Harman Kardon Stereo Receiver 13828 User Manual

System 13828  
AVR 138 Audio/Video Receiver  
DVD 28 Digital Versatile Disc Player  
OWNER’S MANUAL  
DVD 28  
Open/Close  
AUDIO/VIDEO  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Information  
spilled or objects have fallen into the apparatus,  
the apparatus has been exposed to rain or mois-  
ture, does not operate normally, or has been  
dropped.  
a firm and level surface. When placing the  
unit on a shelf, be certain that the shelf and  
any mounting hardware can support the  
weight of the product.  
Important Safety Information  
1. Read these instructions.  
2. Keep these instructions.  
Make certain that proper space is provided  
both above and below the unit for ventilation.  
If this product will be installed in a cabinet or  
other enclosed area, make certain that there  
is sufficient air movement within the cabinet.  
Under some circumstances a fan may be  
required.  
15. Do not expose this apparatus to dripping or  
splashing and ensure that no objects filled with  
liquids, such as vases, are placed on the appara-  
tus.  
3. Heed all warnings.  
4. Follow all instructions.  
5. Do not use this apparatus near water.  
6. Clean only with a dry cloth.  
16. To completely disconnect this apparatus  
from the AC Mains, disconnect the power supply  
cord plug from the AC receptacle.  
7. Do not block any ventilation openings. Install  
in accordance with the manufacturer’s instruc-  
tions.  
Do not place the unit directly on a carpeted  
surface.  
17. The mains plug of the power supply cord  
shall remain readily operable.  
Avoid installation in extremely hot or cold  
locations, or an area that is exposed to direct  
sunlight or heating equipment.  
8. Do not install near any heat sources such as  
radiators, heat registers, stoves or other appara-  
tus (including amplifiers) that produce heat.  
18. Do not expose batteries to excessive heat  
such as sunshine, fire or the like.  
Avoid moist or humid locations.  
The lightning flash with arrowhead  
symbol, within an equilateral triangle,  
is intended to alert the user to the  
9. Do not defeat the safety purpose of the polar-  
ized or grounding-type plug. A polarized plug has  
two blades with one wider than the other. A  
grounding-type plug has two blades and a third  
grounding prong. The wide blade or the third  
prong is provided for your safety. If the provided  
plug does not fit into your outlet, consult an elec-  
trician for replacement of the obsolete outlet.  
Do not obstruct the ventilation slots on the  
top of the unit, or place objects directly over  
them.  
presence of uninsulated “danger-  
ous voltage”within the product’s enclosure that  
may be of sufficient magnitude to constitute a  
risk of electric shock to persons.  
Cleaning  
When the unit gets dirty, wipe it with a clean,  
soft, dry cloth. If necessary, wipe it with a soft  
cloth dampened with mild soapy water, then a  
fresh cloth with clean water. Wipe dry  
immediately with a dry cloth. NEVER use  
benzene, aerosol cleaners, thinner, alcohol or any  
other volatile cleaning agent. Do not use  
abrasive cleaners, as they may damage the finish  
of metal parts. Avoid spraying insecticide near  
the unit.  
The exclamation point within an equi-  
lateral triangle is intended to alert  
10. Protect the power cord from being walked  
on or pinched, particularly at plugs, convenience  
receptacles and the point where they exit from  
the apparatus.  
the user to the presence of impor-  
tant operating and maintenance  
(servicing) instructions in the literature accompa-  
nying the product. WARNING: To reduce the  
risk of fire or electric shock, do not expose this  
apparatus to rain or moisture.  
11. Only use attachments/accessories specified  
by the manufacturer.  
12. Use only with the cart, stand, tripod, bracket  
or table specified by the manufacturer or sold  
with the apparatus. When a cart is used, use  
caution when moving the cart/apparatus  
combination to avoid injury from tip-over.  
Do Not Open the Cabinet  
Moving the Unit  
There are no user-serviceable components inside  
this product. Opening the cabinet may present a  
shock hazard, and any modification to the  
product will void your guarantee. If water or any  
metal object such as a paper clip, wire or a  
staple accidentally falls inside the unit, discon-  
nect it from the AC power source immediately,  
and consult an authorized service station.  
Before moving the unit, be certain to disconnect  
any interconnection cords with other compo-  
nents, and make certain that you disconnect the  
unit from the AC outlet.  
13. Unplug this apparatus during lightning  
storms or when unused for long periods of time.  
Unpacking  
The carton and shipping materials used to pro-  
tect your new receiver during shipment were  
specially designed to cushion it from shock and  
vibration. We suggest that you save the carton  
and packing materials for use in shipping if you  
move, or should the unit ever need repair.  
14. Refer all servicing to qualified service per-  
sonnel. Servicing is required when the apparatus  
has been damaged in any way, such as power  
supply cord or plug is damaged, liquid has been  
Installation Location  
To assure proper operation and to avoid the  
potential for safety hazards, place the unit on  
To minimize the size of the carton in storage,  
you may wish to flatten it. This is done by  
carefully slitting the tape seams on the bottom  
and collapsing the carton. Other cardboard  
inserts may be stored in the same manner.  
Packing materials that cannot be collapsed  
should be saved along with the carton in a  
plastic bag.  
If you do not wish to save the packaging  
materials, please note that the carton and other  
sections of the shipping protection are  
recyclable. Please respect the environment and  
discard those materials at a local recycling  
center.  
SAFETY INFORMATION 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control Functions, common for AVR 138 and DVD 28  
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
Power On Button  
Not active  
IR Transmitter Window  
Power Off Button  
Mute  
Input Selectors  
Info  
Volume Up/Down  
HD Mode Selector  
Speaker Select/Setup  
OK Button  
Delay/Status Button  
Memory/Angle Button  
Clear Button  
Preset Up/Down  
RDS Select/Progressive Scan/Interlaced  
Button  
b
c
d
e
f
a
h
g
f
e
g
d
b
7
8
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
a
b
c
Playlist  
A-B  
DTS Neo:6 Mode Selector  
Stereo Mode Selector  
Logic 7 Selector  
c
a
j
Dim Button  
Z
Transport Buttons  
Skip Up/Down Buttons (DWN)/(UP)  
Night Mode  
DTS Digital Mode Selector  
Dolby Mode Selector  
Repeat  
k
l
Y
X
Random  
Tone Mode/Test Tone ON/OFF  
Tuning Up/Down  
Direct Button  
Tuner Mode/Zoom  
Numeric Keys  
Digital Select/Audio Mode  
Navigation Buttons  
Channel Select /Disc Menu Button  
V.OFF  
Surround Mode Selector/Program  
Down/Subtitle Button  
Sleep/Program Up/Audio Select Button  
Title  
6-Channel Direct Input  
AM/FM Tuner Select  
AVR Selector  
m
o
W
U
V
n
T
R
p
r
q
s
S
`
z
t
v
y
u
d
e
f
g
h
x
w
138  
28  
4 REMOTE CONTROL FUNCTIONS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control Functions, common for AVR 138 and DVD 28  
IMPORTANT NOTE: The 13828 remote has  
some buttons that perform different functions. If  
8
HD Mode Selector (DVD): When the  
DVD player is connected to a video display using  
the HDMI Output , the display sends infor-  
C
Memory/Angle Button: Press this button  
to enter a radio station into the AVR’s preset  
memory. Two underline indicators will flash at the  
right side of the Main Information Display  
F, you then have five seconds to enter a preset  
memory location using the Numeric Keys  
you press the AVR Button  
h
, one set of func-  
A
tions is active, identical to the functions for but-  
tons CD, Tape, Video 1/2/3. If you press the DVD  
mation to the DVD indicating the highest video  
resolution it is capable of handling, and the  
DVD automatically sets the video output to  
match it. Pressing this button allows you to  
manually change the output resolution, with  
your selection indicated by the Video Output  
Indicators O.  
The DVD will not allow you to select a resolution  
beyond the capabilities of your display, and if  
you try to do so, an on-screen error message will  
appear to alert you to the selection of an incom-  
patible video format. Changes made with this  
button remain active until the DVD or the dis-  
play is turned off. When either is turned off, and  
then on again, the DVD will revert to the default  
setting transmitted by the display.  
Button  
5
, some of the buttons change their  
X.  
function as indicated above the button itself, and  
explained below. Refer to the function table for  
an overview of functions in both modes.  
(See page 23 for more information.)  
For DVD: Press to access various camera angles  
on a DVD (If the DVD contains multiple camera  
angles) or to rotate JPEG images.  
0
Power On Button: Press this button to  
turn on the power to the AVR or the DVD selected  
by pressing either the AVR or the DVD Button  
D
Clear Button: Press this button to clear  
incorrect entries when using the remote to  
directly enter a radio station’s frequency.  
h
1
2
or  
5.  
This indicator is not active.  
E
Preset Up/Down: When the tuner is in  
IR Transmitter Window: Point this window  
use, press these buttons to scroll through the  
stations programmed into the AVR’s memory.  
When CD or DVD is selected using the Input  
Selector button  
tion as Slow Fwd/Rev (DVD) or ”+10” (CD).  
towards the AVR when pressing buttons on the  
remote to make certain that infrared commands  
are properly received.  
5, these buttons may func-  
9
Speaker Select/Setup: Press this button  
3
Power Off Button: Press this button to  
to begin the process of configuring the AVR’s  
Bass Management System for use with the type  
of speakers used in your system. Once the but-  
K L  
place the AVR or a selected device unit in the  
Standby mode. If held for more than 3 seconds,  
both the AVR and the DVD switch to Standby.  
F
RDS Select/Progressive Scan/Interlaced  
Button: Press this button to display the various  
messages that are part of the RDS data system of  
the AVR’s tuner. (See page 24 for more informa-  
tion on RDS).  
ton has been pressed, use the  
/
buttons  
Z
to select the channel you wish to set up.  
4
Mute: Press this button to momentarily  
Press the OK button  
speaker type (see page 14 for more informa-  
tion.)  
A
and then select the  
silence the AVR or TV set being controlled,  
depending on which device has been selected.  
For DVD: Press this button to change the resolu-  
tion of the Component Video Output between  
standard definition and progressive definition  
(PAL interlaced and PAL progressive; NTSC inter-  
laced and NTSC progressive).  
5
Input Selectors: Pressing one of these  
For DVD: Press this button to use the DVD’s on-  
screen menu system to adjust the player’s con-  
figuration settings. Note that the Info Button  
buttons will perform three actions at the same  
time. First, if the AVR is not turned on, this will  
power up the unit. Next, it will select the source  
shown on the button as the input to the AVR.  
Finally, the DVD Button will switch the double-  
function remote buttons to their DVD functions.  
After pressing the DVD Button, you must press  
The new setting will become effective after  
quitting the Setup menu.  
6
must be pressed to access the DVD’s  
Information menu to obtain detailed disc infor-  
mation, and to configure the playback mode of  
the disc.  
G
Playlist (DVD): Press this button to  
change the playback order of the disc.  
the AVR Selector button  
h
again to operate  
A
OK Button: This button is used to enter  
H
A-B (DVD): Press to select section A-B and  
all the AVR’s functions with the remote. Note  
that pressing the DVD Button switches on BOTH  
the AVR and the DVD, whereas pressing the AVR  
Button just switches on the AVR.  
settings into the AVR’s memory. It is also used in  
the setup procedures for delay time, speaker  
configuration and channel output level  
adjustment.  
to play repeatedly.  
I
DTS Neo:6 Mode Selector: Pressing this  
selector button cycles the AVR through the  
various DTS Neo:6 modes, which extract a five-  
channel surround field from two-channel  
program material (from PCM source or analog  
input signal). The first press selects the last DTS  
Neo:6 surround mode that was in use, and each  
subsequent press selects the next mode in the  
following order:  
6
Info (DVD): Press for detailed informations  
B
Delay/Status Button: Press this button to  
on the disc playing (Video/Audio Bit rate, Movie  
aspect ratio and others), and for current player  
settings made. Note that the unit doesn’t react  
on any transport button as long as the info  
menu is displayed. Press again to remove  
information from screen.  
begin the process for setting the delay times  
used by the AVR when processing surround  
sound. After pressing this button, the delay  
times are entered by pressing the OK button  
K L  
A
and then using the  
/
buttons  
Z
to  
change the setting. Press the Set button again to  
complete the process. (See page 16 for more  
information.)  
DTS Neo:6 MUSIC  
7
Volume Up/Down: Press these buttons to  
raise or lower the system volume.  
DTS Neo:6  
CINEMA  
For DVD: Press while a disc is playing to view  
banner display. Use the ARROW buttons to move  
through the different features in the Banner  
Display. When a symbol is highlighted, press OK  
on the remote to select it.  
REMOTE CONTROL FUNCTIONS 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control Functions, common for AVR 138 and DVD 28  
J
Stereo Mode Selector: Press this button  
P
DTS Digital Mode Selector: When a DTS  
W
Tuner Mode/Zoom: Press this button  
to select a stereo playback mode. When the but-  
ton is pressed so that DSPSURROFF  
source is in use the AVR will select the  
when the tuner is in use to select between auto-  
matic tuning and manual tuning. When the but-  
ton is pressed so MANUALappears in the  
appropriate mode automatically and no other  
mode will be available. Pressing this button will  
display the mode currently selected by the AVR´s  
decoder, depending on the surround material  
played and the speaker setting.  
appears in the Main Information Display  
F,  
the AVR will operate in a bypass mode with true  
fully analog, two-channel left/right stereo mode  
with no surround processing or bass manage-  
ment as opposed to other modes where digital  
processing is used. When the button is pressed  
so that SURROUNDOFFappears in the  
Main Information Display  
F, pressing the  
Tuning buttons will move the frequency  
U
7
up or down in single-step increments. When the  
FM band is in use and AUTOappears in the  
Q
Dolby Mode Selector: This button is used  
Main Information Display  
F, pressing this  
to select one of the available Dolby Surround  
processing modes. Each press of this button will  
select one of the Dolby Pro Logic II modes,  
Dolby 3 Stereo or Dolby Digital. Note that the  
Dolby Digital mode is only available with a  
digital input selected and the other modes only  
as long as a Dolby Digital source is not playing.  
button will change to monaural reception mak-  
ing even week stations audible. (See page 23 for  
more information.)  
Main Information Display  
F, you may enjoy  
a two-channel presentation of the sound along  
with the benefits of bass management. When  
the button is pressed so that 5CHSTEREO  
appears, the stereo signal is routed to all five  
speakers, if installed.(See page 16 for more  
information on stereo playback modes).  
When a DVD or VCD is playing, press this button  
to zoom the picture so that it is enlarged. There  
are 4 steps to the zoom function, each progres-  
sively larger. Press through each of the zoom  
stages to return to a normal picture.  
R
Repeat (DVD): Each press of this button  
changes the playback mode to repeat a chapter  
or track or the entire disc. A repeat icon will  
appear in the upper right corner of the screen  
indicating the current repeat mode. If the Player  
Information Screen is active, the changes will be  
displayed on screen.  
K
Logic 7 Selector: Press this button to  
X
Numeric Keys: These buttons serve as a  
select one of the available Logic 7 surround  
modes. (See page 19 for the available Logic 7  
options).  
ten-button numeric keypad to enter tuner preset  
positions. For DVD play you may enter track  
numbers directly, followed by OK to go to the  
track.  
L
Dim Button: Press this button to activate  
the Dimmer function, which reduces the bright-  
ness of the front panel display, or turn it off  
entirely. The first press of the button shows the  
default state, which is full brightness by  
indicating VFDFULLin the Main  
S
Random (DVD): Press for RANDOM  
Y
Digital Select/Audio Mode: Press this  
playback in random order.  
button to assign one of the digital inputs  
4G9L to a source. (See page 14 for more  
information on using digital inputs.) Audio  
Mode: When operating the DVD, press this  
Button to switch between Audio Modes.  
T
Tone Mode: Pressing this button enables  
or disables the Bass and Treble tone controls.  
When the button is pressed so that the words  
TONEINappear in the Main Information  
Information Display  
F. Press the button  
again within five seconds to reduce the  
Display  
F, the settings of the Bass and  
Z
Navigation Buttons: These are multi-pur-  
brightness by 50%, as indicated by VFD  
HALF. Press the button again within five  
seconds and the main display will go completely  
dark. Note that this setting is temporary; the  
display will always return to full brightness when  
the AVR is turned on. In addition,both the  
Treble controls will affect the output signals.  
When the button is pressed so that the words  
TONEOUTappear in the Main Information  
pose buttons.They will be used most frequently to  
select a surround mode.These buttons are also  
used to increase or decrease output levels when  
configuring the unit, to select speaker  
Display  
F, the output signal will be “flat,”  
without any bass or treble alteration.  
configuration or to select the digital inputs.  
Power Indicator  
2
and the blue accent  
U
Tuning Up/Down:When the tuner is in use,  
a
Channel Select /Disc Menu Button: This  
lighting inside the volume control will always  
remain at full brightness regardless of the  
setting. This is to remind you that the AVR is still  
turned on.  
these buttons will tune up or down through the  
selected frequency band. If the Tuner Mode  
button is used to start the process of setting the  
AVR’s output levels with an external source. Once  
K L  
button  
on the front panel was held pressed so that  
AUTOappears in the Main Information  
Display , pressing either of the buttons will  
W
has been pressed or the Band button  
this button is pressed, use the  
/
buttons  
Z
to  
8
select the channel being adjusted, then press the  
OK button  
again, to change the level setting. (See page 22 for  
more information.)  
K L  
/
A
, followed by the  
buttons  
M
Transport Buttons: These buttons operate  
F
the DVD player.  
cause the tuner to seek the next station with  
acceptable signal strength for quality reception.  
When the MANUALappears in the Main  
Information Display  
buttons will tune stations in single-step  
N
Skip Up/Down Buttons (DVD):  
DVD Disc Menu: Displays the actual DVD Disc  
Menu on the TV screen in play mode. When  
playing discs with JPEG images, pressing this  
button will access the thumbnails.  
(DWN): Press to go to beginning of current  
track. Press again quickly to go to beginning of  
previous track. After pressing the PAUSE button,  
each press of this button will move the image in  
reverse frame by frame.  
(UP): Press to go to beginning of next track.  
After pressing the PAUSE button, each press of  
this button will move the image forwards frame  
by frame.  
F, pressing these  
increments. (See page 23 for more information.)  
b
V.OFF: Press to turn off video output for  
V
Direct Button: Press this button when the  
improved performance from audio-only discs.  
Press again to restore video output.  
tuner is in use to start the sequence for direct  
entry of a station’s frequency. After pressing the  
button simply press the proper Numeric Keys  
X
to select a station (See page 23 for more  
O
Night Mode: Press this button to activate  
information on the tuner).  
the Night mode. This mode is available only with  
Dolby Digital encoded digital sources, and it  
preserves dialog (center channel) intelligibilty at  
low volume levels (See page 17 for more  
information).  
6 REMOTE CONTROL FUNCTIONS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Function List  
No.  
Button Name  
AVR/TAPE/CD/VID1/VID2/VID3  
DVD  
DVD  
Power On  
Power Off  
Mute (AVR)  
AVR  
c
Surround Mode Selector/Program  
AUDIO  
Power On  
Power Off  
Mute  
AVR Power On  
DVD  
TAPE  
VID1  
AM/FM  
CD  
Down/Subtitle Button: Press this button to  
begin the process of changing the surround  
mode. After the button has been pressed,  
K L  
1
2
5
44  
6
6
6
43  
6
Power On  
Power Off  
Mute  
AVR  
DVD  
TAPE  
VID1  
AM/FM  
CD  
use the  
/
buttons  
Z
to select the desired  
surround mode. (See page 20 for more informa-  
tion).  
DVD  
TAPE  
VID1  
AM/FM  
CD  
When a DVD is playing, press to select a subtitle  
language or to turn subtitles off.  
Note: Due to the variations in how DVD discs  
are authored, the subtitle languages selected  
with the Subtitle Button may not accurately  
reflect the actual languages available on the  
disc. It is recommended that subtitles be select-  
ed using the disc’s menu.  
42  
6
6
40  
41  
8
6CH  
VID2  
VID3  
Sleep/ Audio  
Title  
6CH  
VID2  
VID3  
Sleep  
6CH  
VID2  
VID3  
Audio  
Title  
Info  
Info  
8
Vol Up  
Surr./ Subt.  
V.OFF  
Vol Up  
Surr.  
Vol Up  
Subtitle  
V.OFF  
HD Mode  
Vol Down  
Disc Menu  
Setup  
Up  
39  
38  
9
d
Sleep/Program Up>/Audio Select  
Button: Press this button to place the unit in  
the Sleep mode. After the time shown in the  
display, the AVR will automatically go into the  
Standby mode. Each press of the button changes  
the time until turn-off in the  
HD-M  
8
Vol Down  
CH. / Disc menu  
SPKR / Setup  
Level+/Up  
Left <  
Vol Down  
Channel  
Speaker  
Level+/Up  
Left <  
SET  
Right >  
Level-/Down  
Digital  
Delay  
1
2
3
4
5
6
37  
10  
36  
36  
11  
36  
36  
35  
12  
34  
34  
34  
34  
34  
34  
34  
34  
33  
34  
34  
13  
31  
32  
14  
15  
31  
30  
16  
15  
29  
28  
18  
17  
27  
28  
19  
25  
21  
20  
24  
24  
22  
23  
23  
23  
23  
23  
23  
Left  
following order:  
OK  
Enter  
Right  
Down  
Audio mode  
Status  
1
2
3
4
5
90  
80  
70  
60  
50  
min  
min  
min  
min  
min  
Right >  
Level-/Down  
Digital / Audio mode  
Delay / Status  
1
2
3
4
5
40  
30  
20  
10  
OFF  
min  
min  
min  
min  
Hold the button pressed for two seconds to turn  
off the Sleep mode setting.  
Note that this button is also used to change  
channels on your TV, VCR and SAT receiver when  
selected.  
6
7
8
6
7
8
DVD: Press to access various audio languages on  
a DVD (If the DVD contains multiple audio  
streams).  
7
8
TUN-M / Zoom  
9
0
MEM / Angle  
Tuning Up  
Direct  
TUN-M  
9
0
Memory  
Tuning Up  
Direct  
Clear  
Zoom  
9
0
e
Title: When a disc is playing, press to make  
the player go back to the first section of the disc.  
If you are playing a DVD-Audio disc that con-  
tains other formats the DVD is capable of play-  
ing, such as linear PCM or Dolby Digital 5.1,  
pressing this button may enable you to switch  
playback from one audio format to another.  
Angle  
Clear  
Clear  
Slow Up  
Preset Up  
Tuning Down  
Tone  
RDS/ P/I  
Preset Down  
Random  
Repeat  
A-B  
Playlist  
Dolby Surround  
DTS Surround  
DTS NEO:6  
Night  
Logic7  
Stereo  
Skip Down  
Skip Up  
DIM  
Preset Up  
Tuning Down  
Tone Mode/Test Tone ON-OFF  
RDS  
f
6-Channel Direct Input: Press this button  
to select the component connected to the  
6-Channel Direct Input as the audio. Note  
P/I  
Preset Down  
Slow Down  
Random  
Repeat  
A-B  
Playlist  
Dolby Surround  
DTS Surround  
DTS NEO:6  
Night  
Logic7  
Stereo  
Prev Step  
Next Step  
Dimmer  
REW  
N
that when you wish to use the Six Channel  
Direct Input in conjunction with a video source,  
you must first select the video source by pressing  
Dolby Surround  
DTS Surround  
DTS NEO:6  
Night  
Logic7  
Stereo  
Skip Down(DVD)  
Skip Up(DVD)  
Dimmer  
Rew(DVD)  
Play(DVD)  
FF(DVD)  
Open/Close(DVD)  
Stop(DVD)  
Pause(DVD)  
one of the Input Selectors  
button to choose the 6-Channel Direct Input  
as the audio source.  
5. Then press this  
N
g
AM/FM Tuner Select: Press this button to  
select the AVR’s tuner as the listening choice.  
Pressing this button when the tuner is in use will  
select between the AM and FM bands.  
G
AB  
Rew(  
Play(  
)
h
AVR Selector: Pressing this button will  
)
Play  
FF  
Open/Close  
Stop  
Pause  
switch the remote so that it will operate the AVR’s  
functions. If the AVR is in the Standby mode, it will  
also turn the AVR on.  
H
FF(  
)
Open/Close  
Stop  
Pause  
REMOTE CONTROL FUNCTIONS 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Front Panel Controls  
D
F
I
J
5
DIGITAL  
LOGIC 7  
VID 1  
DVD  
CD  
PRO LOGIC  
3 STEREO  
VID 2  
VID 3  
DSP  
FMAM  
TAPE  
5 CH. STEREO  
SURR. OFF  
6 CH  
G
E
B
6
7
8
2
1
H
A
4
C
9
3
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
Main Power Switch  
System Power Control  
Power Indicator  
Tuning  
Tuner Band Selector  
Remote Sensor Window  
Main Information Display  
Digital Coax 3 Input  
Video 3 input jacks  
Volume Control  
F
G
H
I
J
Preset Stations Selector  
Input Source Selector  
RDS Select Button  
Surround Mode Selector  
Surround Mode Indicators  
Headphone Jack  
Digital Optical 3 Input  
Speaker/Channel Input Indicator  
Surround Mode Group Selector  
Input Indicators  
0
Main Power Switch: Press this button to  
1
System Power Control: When the Main  
is “ON,” press this button to  
5Speaker/Channel Input Indicators:  
apply power to the AVR. When the switch is  
pressed in, the unit is placed in a Standby  
mode, as indicated by the orange LED  
button MUST be pressed in to operate the unit.  
To turn the unit off completely and prevent the  
use of the remote control, this switch should be  
pressed until it pops out from the front panel  
so that the word “OFF” may be read at the top  
of the switch.  
Power Switch  
turn on the AVR; press it again to turn the unit  
off (to Standby). Note that the Power  
Indicator  
0
These indicators are multipurpose, indicating  
either the speaker type selected for each channel  
or the incoming data-signal configuration. The  
left, center, right, right surround and left  
surround speaker indicators are composed of  
three boxes, while the subwoofer is a single box.  
The center box lights when a “Small” speaker is  
selected, and the two outer boxes light when  
“Large” speakers are selected. When none of  
the boxes are lit for the center, surround or  
subwoofer channels, no speaker has been  
selected for that position. (See page 16 for more  
information on configuring speakers.) The letters  
inside each of the center boxes display active  
input channels. For standard analog inputs, only  
the L and R will light, indicating a stereo input.  
When a digital source is playing, the indicators  
will light to display the channels begin received  
at the digital input. When the letters flash, the  
digital input has been interrupted. (See page 15  
for more information on the Channel Indicators).  
2
. This  
2
will turn blue when the unit is on.  
2
Power Indicator: This LED will be  
illuminated in orange when the unit is in the  
Standby mode to signal that the unit is ready to  
be turned on. When the unit is in operation, the  
indicator will turn blue.  
NOTE: This switch is normally left in the “ON”  
position.  
3
Headphone Jack: This jack may be used to  
listen to the AVR’s output through a pair of  
headphones. Be certain that the headphones  
have a standard 6.3 mm stereo phone plug.  
Note that the speakers will automatically be  
turned off when the headphones are connected.  
4
Digital Optical 3 Input: Connect the  
optical digital audio output of an audio or video  
product to this jack. When the Input is not in use,  
be certain to keep the plastic cap installed to  
avoid dust contamination that might degrade  
future performance.  
8 FRONT PANEL CONTROLS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Front Panel Controls  
6
Surround Mode Group Selector: Press  
9
Preset Stations Selector: Press this  
D
Surround Mode Indicators: Indicator will  
this button to select the top-level group of  
surround modes. Each press of the button will  
select a major mode grouping in the following  
order:  
button to scroll up or down through the list of  
stations that have been entered into the preset  
memory. (See page 23 for more information on  
tuner programming.)  
illuminate in front of the surround mode that is  
currently in use.  
E
Remote Sensor Window: The sensor  
behind this window receives infrared signals  
from the remote control. Aim the remote at this  
area and do not block or cover it unless an  
external remote sensor is installed.  
Dolby Modes DTS Digital Modes DSP  
Modes Stereo Modes Logic 7 Modes  
A
Input Source Selector: Press this button  
to change the input by scrolling through the list  
of input sources.  
Once the button is pressed so that the name of  
the desired surround mode group appears in the  
B
RDS Select Button: Press this button to  
F
Main Information Display: This display  
Lower Display Line  
F
, press the Surround  
display the various messages that are part of the  
RDS data system of the AVR’s tuner. (See page 24  
for more information on RDS).  
delivers messages and status indications to help  
you operate the receiver.  
Mode Selector to cycle through the indi-  
C
vidual modes available. For example, press this  
button to select Dolby modes, and then press  
the Surround Mode Selector  
G
Digital Coax 3 Input: This jack is normally  
C
Surround Mode Selector: Press this but-  
used for connection to the output of portable  
digital audio devices, video game consoles or  
other products that have a coax digital jack.  
C
to choose  
ton to select from among the available surround  
mode options for the mode group selected. The  
specific modes will vary based on the number of  
speakers available, the mode group and if the  
input source is digital or analog. For example,  
press the Surround Mode Group Selector  
from the various mode options.  
7
Tuning Selector: Press the left side of the  
H
Video 3 Input Jacks: These audio/video  
button to tune lower frequency stations and the  
right side of the button to tune higher frequency  
stations. When a station with a strong signal is  
reached, MANUALTUNEDor AUTO  
jacks may be used for temporary connection to  
video games or portable audio/video products  
such as camcorders and portable audio players.  
6
to select a mode grouping such as Dolby or  
TUNEDwill appear in the Main Information  
Logic 7, and then press this button to see the  
mode choices available. For more information on  
mode selection, see page 9.  
I
Volume Control: Turn this knob clockwise  
Display  
F
(see page 23 for more information  
to increase the volume, counterclockwise to  
decrease the volume. If the AVR is muted,  
adjusting volume control will automatically  
release the unit from the silenced condition.  
on tuning stations).  
8
Tuner Band Selector: Pressing this button  
will automatically switch the AVR to the Tuner  
mode. Pressing it again will switch between the  
AM and FM frequency bands, holding it pressed  
for some seconds will switch between stereo  
and mono receiving and between automatic and  
manual tuning mode (See page 23 for more  
information on the tuner).  
J
Input indicators: Indicator will illuminate  
in front of the input that is currently being used  
as the source for the AVR.  
FRONT PANEL CONTROLS 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rear Panel Connections  
d
¢
ª
a
§
£
°
B
b
·
¡
e
c
0
9
A
B
C
D
E
F
G
H
I
J
K
L
M
N
Tape Inputs  
Tape Outputs  
Coaxial Digital Inputs  
Subwoofer Output  
Video Monitor Outputs  
Front/Center Speaker Outputs  
Surround Speaker Outputs  
Component Video Outputs  
Video 1 Component Video Inputs  
AC Power Cord  
Video 1 Video Outputs  
Video 2 Audio Inputs  
Video 2 Video Inputs  
Optical Digital Inputs  
Video 1 Video Inputs  
6-Channel Direct Inputs  
1
2
3
4
5
6
7
8
Video 1 Audio Inputs  
AM Antenna  
Video 1 Audio Outputs  
DVD Audio Inputs  
FM Antenna  
CD Inputs  
Video 2 Component Video Inputs  
DVD Video Inputs  
0
Tape Inputs: Connect these jacks to the  
4
Video 1 Audio Outputs: Connect these  
8
Video 2 Component Video Inputs:  
PLAY/OUT jacks of an audio recorder.  
jacks to the RECORD/INPUT audio jacks on  
a VCR or any other Audio recorder.  
Connect the Y/Pr/Pb component video outputs of  
an HDTV Set-top convertor, satellite receiver, or  
other video source device with component video  
outputs to these jacks.  
1
Tape Outputs: Connect these jacks to the  
RECORD/INPUT jacks of an audio recorder.  
5
DVD Audio Inputs: Connect these jacks to  
the analog audio jacks on a DVD or other video  
source.  
2
Video 1 Audio Inputs: Connect these jacks  
9
Coaxial Digital Inputs: Connect the coax  
to the PLAY/OUT audio jacks on a TV or other  
video source.  
digital output from a DVD player, HDTV receiver,  
LD player, MD player or CD player to these jacks.  
The signal may be either a Dolby Digital signal,  
DTS signal or a standard PCM digital source.  
Do not connect the RF digital output of an LD  
player to these jacks.  
6
FM Antenna: Connect the supplied indoor or  
an optional external FM antenna to this terminal.  
3
AM Antenna: Connect the AM loop antenna  
supplied with the receiver to these terminals. If an  
external AM antenna is used, make connections to  
the AM and GND terminals in accordance with  
the instructions supplied with the antenna.  
7
CD Inputs: Connect these jacks to the  
analog output of a compact disc player or CD  
changer.  
A
Subwoofer Output: Connect this jack to  
the line-level input of a powered subwoofer. If  
an external subwoofer amplifier is used, connect  
this jack to the subwoofer amplifier input.  
10 REAR PANEL CONNECTIONS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rear Panel Connections  
B
Video Monitor Outputs: Connect these  
F
Video 1 Component Video Inputs:  
L
Optical Digital Inputs: Connect the optical  
jacks to the composite and/or S-Video input of a  
TV monitor or video projector to view the output  
of any video source selected by the receiver’s  
video switcher.  
Connect the Y/Pr/Pb component video outputs of  
a DVD player to these jacks.  
digital output from a DVD player, HDTV receiver,  
LD player, MD player or CD player to these jacks.  
The signal may be either a Dolby Digital signal, a  
DTS signal or a standard PCM digital source.  
Note: All component inputs/outputs can be  
used for RGB signals too, in the same way as  
described for the Y/Pr/Pb signals, then connected  
to the jacks with the corresponding color.  
RGB connection is not possible if the source  
outputs a separate sync signal (see page 13).  
C
Front/Center Speaker Outputs: Connect  
M
Video 1 Video Inputs: Connect these jacks  
these outputs to the matching + or – terminals  
on your front/center speakers. When making  
speaker connections, always make certain to  
maintain correct polarity by connecting the red  
(+) terminals on the AVR to the red (+) terminals  
on the speaker and the black (–) terminals on  
the AVR to the black (–) terminals on the  
speakers. (See page 12 for more information on  
speaker polarity.)  
to the PLAY/OUT composite or S-Video jacks on  
a TV or other video source.  
Note: Either the Video or S-Video output of any  
S-Video source must be connected to the  
AVR, not both in parallel, otherwise the video  
may be disturbed or its performance be  
adversely effected.  
G
AC Power Cord: Connect the AC plug to an  
unswitched AC wall output.  
H
DVD Video Inputs: Connect these jacks to  
the composite or S-Video output jacks on a DVD  
player or other video source.  
N
6-Channel Direct Inputs: These jacks are  
used for connection to source devices such as  
DVD-Audio or SACD players with discrete analog  
outputs.  
D
Surround Speaker Outputs: Connect  
I
Video 1 Video Outputs: Connect these  
these outputs to the matching + or – terminals  
on your left and right surround speakers. When  
making speaker connections always make cer-  
tain to maintain correct polarity by connecting  
the red (+) terminals on the AVR to the red (+)  
terminals on the speakers and the black (–)  
terminals on the AVR to the black (–) terminals  
on the speakers. See page 12 for more  
jacks to the RECORD/INPUT composite or  
S-Video jack on a VCR.  
J
Video 2 Audio Inputs: Connect these jacks  
to the PLAY/OUT audio jacks on a VCR or other  
video source.  
K
Video 2 Video Inputs: Connect these jacks  
to the PLAY/OUT composite or S-Video jacks on  
information on speaker polarity.  
a second VCR or other video source.  
E
Monitor Component Video Outputs:  
Connect these outputs to the component video  
inputs of a video projector or monitor. When a  
source connected to one of the two  
Component Video Inputs 8Fis selected  
the signal will be sent to these jacks.  
REAR PANEL CONNECTIONS 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation and Connections  
After unpacking the unit, and placing it on a solid  
surface capable of supporting its weight, you will  
need to make the connections to your audio and  
video equipment.  
NOTE: While most speaker manufacturers  
adhere to an industry convention of using black  
terminals for negative and red ones for positive,  
some manufacturers may vary from this  
configuration. To assure proper phase and  
optimal performance, consult the identification  
plate on your speaker or the speaker’s manual to  
verify polarity. If you do not know the polarity of  
your speaker, ask your dealer for advice before  
proceeding, or consult the speaker’s  
Audio Equipment Connections  
We recommend that you use high-quality  
interconnect cables when making connections to  
source equipment and recorders to preserve the  
integrity of the signals.  
5. Connect the supplied FM antenna to the FM  
(75 ohm) connection . The FM antenna may  
6
be an external roof antenna, an inside powered  
or wire lead antenna or a connection from a  
cable system. Note that if the antenna or  
connection uses 300-ohm twin-lead cable, you  
must use a 300-ohm-to-75-ohm adapter to  
make the connection.  
manufacturer.  
When making connections to audio source  
equipment or speakers it is always a good  
practice to unplug the unit from the AC wall  
outlet. This prevents any possibility of  
accidentally sending audio or transient signals to  
the speakers that may damage them.  
We also recommend that the length of cable  
used to connect speaker pairs be identical. For  
example, use the same length piece of cable to  
connect the front-left and front-right or  
surround-left and surround-right speakers,  
even if the speakers are a different distance  
from the AVR.  
6. Connect the front, center and surround  
speaker outputs CDto the respective  
speakers.  
Important Note : In order to clearly identify all  
connectors and simplify nstallation, as per the  
new EIA/CEA-863 standard, all connections are  
colour coded as follows:  
For Speakers and Audio In/Outputs: White (Left,  
speakers front) and Red (Right, speakers front).  
For Speakers: Green (Center), Blue (Left  
Surround) and Grey (Right Surround).  
To assure that all the audio signals are carried to  
your speakers without loss of clarity or  
7. Connections to a subwoofer are normally  
made via a line level audio connection from the  
resolution, we suggest that you use high-quality  
speaker cable. Many brands of cable are  
available and the choice of cable may be  
influenced by the distance between your  
speakers and the receiver, the type of speakers  
you use, personal preferences and other factors.  
Your dealer or installer is a valuable resource to  
consult in selecting the proper cable.  
Subwoofer Output  
A
to the line-level input  
of a subwoofer with a built-in amplifier. When a  
passive subwoofer is used, the connection first  
goes to a power amplifier, which will be  
connected to one or more subwoofer speakers.  
If you are using a powered subwoofer that does  
not have line-level input connections, follow the  
instructions furnished with the speaker for  
connection information.  
For Audio Output: Purple (Subwoofer).  
For Composite Video In/Outputs: Yellow.  
For Digital Audio In/Outputs: Orange.  
1. Connect the analog output of a CD player to  
Regardless of the brand of cable selected, we  
recommend that you use a cable constructed of  
fine, multistrand copper with an area greater  
than 2 mm2.  
Cable with an area of 1.5 mm2 may be used for  
short runs of less than 4 m. We do not  
the CD inputs  
7.  
Note: Speaker sets with two front satellites and  
a passive subwoofer must be connected to the  
NOTE: When the CD player has both fixed and  
variable audio outputs it is best to use the fixed  
output unless you find that the input to the  
receiver is so low that the sound is noisy, or so  
high that the signal is distorted.  
front speaker outputs  
C
only rather than to the  
Subwoofer Output  
A.  
8. If an external multi-channel audio source with  
5.1 outputs such as an external digital  
processor/decoder, DVD-Audio or SACD player is  
used, connect the outputs of that device to the  
recommend that you use cables with an area less  
than 1mm2 due to the power loss and  
2. Connect the analog Play/Out jacks of a  
cassette deck, MD, CD-R or other audio recorder  
degradation in performance that will occur.  
to the Tape Input jacks  
Record/In jacks on the recorder to the Tape  
Output jacks on the AVR.  
0. Connect the analog  
6-Channel Direct Inputs  
N.  
When connecting wires to the speakers, be  
certain to observe proper polarity. Remember to  
connect the “negative” or “black” wire to the  
same terminal on both the receiver and the  
speaker. Similarly, the “positive” or “red” wire  
should be connected to like terminals on the  
AVR and speaker.  
1
3. Connect the output of any digital sources to  
the appropriate input connections on the AVR  
rear panel. Note that the Optical and Coaxial  
digital inputs L94Gmay be used with a  
Dolby Digital or DTS source or the output of a  
conventional CD, MD or LD player’s PCM  
(S/P-DIF) output.  
4. Assemble the AM Loop Antenna supplied with  
the unit as shown below. Connect it to the AM  
and GND screw terminals  
3.  
12 INSTALLATION AND CONNECTIONS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation and Connections  
7. If another component video device is avail-  
able, connect it to the Video 2 Component  
Video Equipment Connections  
Video equipment is connected in the same man-  
ner as audio components. Again, the use of high-  
quality interconnect cables is recommended to  
preserve signal quality. To ensure best video  
performance S-Video sources should be  
connected to the AVR only with their S-Video  
In/Outputs, not with their composite video  
connectors too.  
Video Input jacks  
for this device should be made to either the  
Video 2 Input jacks or any of the Coaxial  
or Optical Digital Input jacks 9L  
8. The audio connections  
J
.
8. If the component video inputs are used,  
connect the Component Video Output  
E
to  
the component video inputs of your TV, projector  
or display device.  
1. Connect a VCR’s audio and video Play/Out  
jacks to the Video 2 In jacks JKon the rear  
panel. The Audio and Video Record/In jacks on  
the VCR should be connected to the Video 1  
Out jacks 4I on the AVR.  
9. If you have a camcorder, video game or other  
audio/video device that is connected to the AVR  
on a temporary, rather than permanent basis,  
connect the audio, video and digital audio out-  
puts of that device to the Front Panel Inputs  
4GH. A device connected to the Video 3  
2. Although any video device may be connected  
to these jacks, we recommend connecting your  
TV to the Video 1 Audio/Video Input Jacks  
2M so that you may take advantage of the  
fact that the remote control is preprogrammed  
with TV product codes for the Video 1 device.  
For the same reason, we recommend connecting  
your video recorder, cable TV converter or satel-  
lite receiver to the Video 2 Audio/Video  
jacks  
H
is selected as the Video 3 input, and  
connected to the digital jacks 4Git is  
selected as "Optical 3" or "Coaxial 3" input.  
(See page 16 for more information on input  
configuration.)  
Video Connection Notes:  
• Y/Pr/Pb Component, RGB (see page 14), or  
Composite video signals may only be viewed  
in their native formats and will not be convert-  
ed to the other formats.  
Input Jacks JK  
.
3. Connect the analog audio and video outputs  
of a DVD to the DVD jacks 5C  
.
• All component inputs/outputs can be used for  
RGB signals too, in the same way as described  
for the Y/Pr/Pb signals, then connected to the  
jacks with the corresponding color.  
4. Connect the digital audio outputs of a CD,  
MD or DVD player, satellite receiver, cable box or  
HDTV converter to the appropriate Optical or  
Coaxial Digital Inputs 9L4G  
Remember that the DVD source defaults to the  
Coaxial 1 Digital Input . All other sources  
default to their analog inputs, although any  
source may be assigned to any digital audio  
input on the receiver.  
.
But this is only correct as long as only the  
three RGB video signals are output by the  
video source, with a sync signal in the "G"  
signal only, without any sync signal output  
separately by the source.  
L
5. Connect the Composite and S-Video  
(if S-Video device is in use) Monitor Output  
jacks on the receiver to the composite and  
B
S-Video input of your television monitor or video  
projector.  
6. If your DVD player and monitor both have  
component video connections, connect the  
component outputs of the DVD player to the  
Video 1 Component Video Inputs  
F. Note  
that even when component video connections  
are used the audio connections must still be  
made to either the analog DVD Audio Inputs  
5
or any of the Coaxial or Optical Digital  
Input jacks 9L  
.
INSTALLATION AND CONNECTIONS 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
System Configuration  
Once the speakers have been placed in the  
room and connected, the remaining steps are to  
program the system configuration memories.  
With the AVR two kind of memories are used,  
those associated individually with the input  
selected, e.g. surround modes, and others  
working independently from any input selected  
like speaker output levels, or delay times used  
by the surround sound processor.  
Settings to be Made With Each  
Input Used  
The AVR features an advanced memory system  
that enables you to establish different settings  
for the speaker configuration, digital input, sur-  
round mode, delay times and output levels for  
each input source. This flexibility enables you to  
custom tailor the way in which you listen to each  
source and have the AVR memorize them. This  
means, for example, that you may associate  
different surround modes and analog or digital  
inputs with different sources, or set different  
speaker configurations with the resultant  
changes to the bass management system or the  
use of the Center speaker. Once these settings  
are made, they will automatically be recalled  
whenever you select an input.  
Pb  
Instructions for users on removal and disposal  
of used batteries.  
Specification of included battery types.  
First Turn On  
These symbols shown on the product, the  
packaging or in the manual or separate infor-  
mation sheet mean that the product itself, as  
well as the batteries included or built into the  
product, should never be thrown away with  
general household waste. Take them to appli-  
cable collection points, where proper treat-  
ment, recycling and recovery takes place, in  
accordance with national or local legislation,  
or European Directives 2002/96/EC and  
2006/66/EC.  
You are now ready to power up the AVR to  
begin these final adjustments.  
1. Plug the Power Cable  
G
into an un-  
switched AC outlet.  
2. Press the Main Power Switch  
0
in until it  
latches and the word “OFF” on the top of the  
switch disappears inside the front panel. Note  
The default settings for the AVR, as it is shipped  
from the factory, have all inputs set for an  
analog source (except for the DVD input, which  
that the Power Indicator  
2
will turn orange,  
indicating that the unit is in the Standby mode.  
has the Coaxial Digital Input 1  
9
as the  
Correct handling of the product and batteries  
to be disposed helps saving resources and  
prevents possible negative effects on the  
environment or human health.  
3. Remove the protective plastic film from the  
front-panel lens. If left in place, the film may  
affect the performance of your remote control.  
default), with Logic 7 Music as the surround  
mode, all speaker positions set to "small", and a  
subwoofer connected. Before using the unit, you  
will probably want to change these settings for  
most inputs so that they are properly configured  
to reflect the use of digital or analog inputs, the  
type of speakers installed and the surround  
mode associated with the input.  
4. Install the three supplied AAA batteries in the  
remote as shown. Be certain to follow the (+)  
and (–) polarity indicators that are on the  
bottom of the battery compartment.  
The batteries included with your equipment  
may be Alkaline, Carbon Zink/Manganese or  
Lithium (button cells) type. All types should  
be disposed of according to the above  
instructions.  
Input Setup  
The first step in configuring the AVR is to select  
an input. This may be done by pressing the front  
To remove the batteries from your equipment  
or remote control, reverse the procedure  
described for inserting batteries in the  
Owners Manual.  
panel Input Source Selector  
desired input’s name appears in the Main  
Information Display , and Indicator will  
illuminate next to the input’s name in the front  
panel Input Indicators . The input may also  
be selected by pressing the appropriate Input  
Selector on the remote control 5g  
A
until the  
F
For products with a built-in battery that lasts  
for the lifetime of the product, removal may  
not be possible for the user. In this case, recy-  
cling or recovery centers handle the disman-  
tling of the product and the removal of the  
battery. If, for any reason, it becomes neces-  
sary to replace such a battery, this procedure  
must be performed by authorized service cen-  
ters.  
5. Turn the AVR on either by pressing the  
J
System Power Control  
Source Selector on the front panel, or via  
the remote by pressing the AVR Selector  
1
or the Input  
A
.
h
The second step is to associate one of the digital  
inputs with the selected input source (if this is  
needed, otherwise the selected analog input will  
remain). Press the Digital Input Select button  
or any of the Input Selectors  
remote. The Power Indicator  
5
2
on the  
will turn blue  
to confirm that the unit is on, and the Main  
Information Display will also light up.  
F
Y
on the remote. Within five seconds, make  
NOTE: After pressing one of the Input Selector  
buttons to turn the unit on, press the AVR  
to have the remote control the AVR  
K L  
your input selection using the  
/
buttons  
5
Z
on the remote until the desired digital or  
analog input is shown in the Main Informa-  
tion Display . Then press the OK button  
to enter the new digital input assignment.  
Selector  
h
functions.  
F
A
After the setting has been made with one input,  
repeat as described above with all inputs in use.  
The digital input associated with the input  
selected can also be changed at any time later  
and the AVR’s memory system will keep the set-  
tings until they are changed again.  
14 SYSTEM CONFIGURATION  
Download from Www.Somanuals.com. All Manuals Search And Download.  
System Configuration  
Speaker Setup  
5. Press the OK button  
A
again, and use the  
When NONEis selected, surround sound  
information will be split between the front-left  
and front-right outputs. Note that for optimal  
performance when no surround speakers are in  
use, the Dolby 3 Stereo mode should be used  
instead of Dolby Pro Logic.  
K L  
This setup tells the AVR which type of speakers  
are in use. This is important as it adjusts the  
settings that determine which speakers receive  
low frequency (bass) information and whether a  
Center speaker should be used or not, separately  
for each input used. For each of these settings  
use the LARGEsetting if the speakers for a  
particular position are traditional full-range  
loudspeakers that are capable of reproducing  
sounds below 100Hz. Use the SMALLsetting  
for smaller, frequency-limited satellite speakers  
that do not reproduce sounds below 100Hz.  
Note that when “small” front (left and right)  
speakers are used, a subwoofer is required to  
reproduce low frequency sounds. If you are in  
doubt as to which category describes your  
speakers, consult the specifications in the  
speakers’ owner’s manual, or ask your dealer.  
/
buttons  
Z
on the remote to select the  
option that best describes your system based on  
the Center speaker definitions shown in preced-  
ing section.  
When SMALLis selected, low frequency center  
channel sounds will be sent to the Fronts, if they  
are set for LARGEand Sub is turned off. When  
Sub is on, low frequency center channel sounds  
will be sent to the subwoofer only.  
8. When you have completed your selection for  
the surround channel, press the OK button  
A,  
K L  
and then press the  
/
buttons  
Z
on  
the remote to change the display to  
S-WSPEAKER.  
When LARGEis selected, a full-range output  
will be sent to the center speaker output, and  
with analog and digital surround modes (except  
with the Pro Logic II Music mode) NO center  
channel signal will be sent to the subwoofer  
output.  
9. Press the OK button  
A, and then press the  
K L  
/
buttons  
Z
on the remote to select the  
option that best describes your Subwoofer sys-  
tem.  
The choices available for the subwoofer position  
will depend on the settings for the other  
speakers, particularly the front left/right  
positions.  
When NONEis selected, no signal will be sent  
to the center channel output. The receiver will  
operate in a “phantom” center channel mode  
and center channel information will be sent to  
the left and right front channel outputs and its  
bass will be sent to the subwoofer output too as  
long as SUB L/R+LFE is selected in the SUB-  
WOOFER line in this menu (see below). This  
mode is needed if no Center speaker is used.  
Note that for the use of Logic 7C surround mode  
a Center speaker is needed, but Logic 7M works  
well without a Center too.  
With the AVR turned on, follow these steps to  
configure the speakers:  
If the front left/right speakers are set to  
SMALL, the subwoofer will automatically be  
set to SUB, which is the “on” position.  
1. Press the Speaker button  
remote. The words FRONTSPEAKERwill  
appear in the Main Information Display  
9
on the  
F
.
If the front left/right speakers are set to  
LARGE, three options are available:  
2. Press the OK button  
A.  
K L  
/
3. Press the  
buttons  
Z
on the remote  
• If no subwoofer is connected to the AVR, press  
to select FRONTLARGEor FRONT  
SMALL, matching the type of speakers you  
have at the left-front and right-front positions,  
as described by the definitions shown in preced-  
ing section.  
the arrow buttons  
Z
so that SUBNONE  
appears in the display. When this option is  
selected, all bass information will be routed to  
the front left/right “main” speakers.  
6. When you have completed your selection for  
the center channel, press the OK button  
A
,
K L  
/
and then press the  
buttons  
Z
on the  
• If a subwoofer is connected to the AVR, you  
have the option to have the front left/right  
“main” speakers reproduce bass frequencies at  
all times, and have the subwoofer operate only  
when the AVR is being used with a digital source  
that contains a dedicated Low Frequency Effects,  
or LFE soundtrack. This allows you to use both  
your main and subwoofer speakers to take  
advantage of the special bass created for certain  
movies. To select that option press the arrow  
remote to change the display to SURR  
SPEAKER.  
When SMALLis selected, low frequency front  
channel sounds will be sent only to the subwoofer  
output. Note that if you choose this option and  
there is no subwoofer connected, you will not  
hear any low frequency sounds from the front  
channels. This setting is not available with stereo  
mode to ensure purest sound by bypassing the  
crossovers of the DSP´s.  
7. Press the OK button  
A
again, and then use  
K L  
the  
/
buttons  
Z
on the remote to select  
the option that best describes your system based  
on the Surround speaker definitions shown in  
preceding section.  
When SMALLis selected, with all digital sur-  
round modes low frequency surround channel  
sounds will be sent to the Fronts, when Sub is  
turned off, or to the subwoofer output when Sub  
is on. With the analog surround modes the rear  
bass feed depends on the mode selected and  
the setting of the sub and front speakers.  
When LARGEis selected, a full-range output  
will be sent to the front left and front right out-  
puts. Depending on the subwoofer configuration  
(see below), the front left and right bass informa-  
tion may also be directed to a subwoofer.  
buttons  
display.  
Z
so that SUBLFEappears in the  
• If a subwoofer is connected and you wish to  
use it for bass reproduction in conjunction with  
the main front left/right speakers, regardless of  
the type of program source or surround mode  
you are listening to, press the arrow buttons  
Important Note: When a speaker set with two  
front satellites and a passive subwoofer is used,  
When LARGEis selected, a full-range output  
will be sent to the surround channel outputs  
(with all analog and digital surround modes),  
and, except with Hall and Theater modes, NO  
surround channel bass will be sent to the  
subwoofer output.  
connected to the front speaker outputs  
the fronts must be set for LARGE.  
C,  
Z
so that SUBL/R+LFEappears in the  
display. When this option is selected, a “com-  
plete” feed will be sent to the front left/right  
“main” speakers, and the subwoofer will receive  
the front left and right bass frequencies under  
the crossover frequency 80 Hz, additionally to  
the LFE soundtrack (see above).  
4.When you have completed your selection for the  
front channels, press the OK button  
A
, and  
KL  
then press the  
/
buttons  
Zon the remote  
to change the display to CENTER  
SPEAKER.  
SYSTEM CONFIGURATION 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
System Configuration  
10. When all speaker selections have been made  
Note that Dolby Digital and DTS will only appear  
as choices when a digital input has been  
selected.  
Stereo-Digital Mode  
for the input selected, press the OK button  
A
When the Stereo-Direct (Bypass) mode is in use  
a full range signal is always sent to the front  
left/right speakers. By its nature, that option  
does not pass the signal through the AVR’s digi-  
tal signal processing, creating the requirement  
for full-range speakers. If your front speakers are  
bandwidth limited, “satellite”speakers, we  
recommend that you do NOT use the Bypass  
mode, but rather use the DSPSURROUND  
OFFmode for stereo listening.  
twice or simply wait for three seconds until the  
display returns to the normal mode.  
After the surround mode setting has been made  
with the current input, repeat the setting with all  
inputs you will use. The surround mode can also  
be changed at any time later, and the AVR’s  
memory system will keep the settings for the  
input selected, until they are changed again.  
To assist in making these settings, the icons in  
the Speaker/Channel Input Indicators  
5
will change as the speaker type is selected at  
each position. When only the inner icon box is  
lit, the speaker is set for “small.” When the inner  
box and the two outer boxes with circles inside  
them are lit, the speaker is set for “large." When  
no indicator appears at a speaker location, that  
position is set for “none” or “no” speaker.  
Configuring the Surround Off  
(Stereo) Modes  
To listen to programs in the two-channel stereo  
mode while taking advantage of the bass  
management system, press the Stereo Mode  
For superior reproduction of two-channel  
program materials, the AVR offers two Stereo  
modes: an analog Stereo-Direct mode that  
bypasses the digital signal processing circuitry  
for a completely analog signal path that pre-  
serves the purity of the original signal, and a  
digital mode that is capable of providing bass  
management for optimal distribution of the low  
frequencies between smaller speakers and a  
subwoofer.  
As an example, in the Figure below, the left front  
and right front speakers are set for “large,” the  
center, left surround and right surround speakers  
are set for small, and a subwoofer is set.  
Selector  
J
until SURROUNDOFF  
appears in the Main Information Display  
and the DSP and SURR.OFFSurround  
F
Mode Indicators  
the SURR.OFFSurround Mode  
Indicators is lit you are in the Stereo-Direct  
(Bypass) mode.  
D
both light up. When only  
D
C
L
R
When this mode is in use, the front left/right  
speakers and subwoofer may be configured to  
meet the requirements of your specific speakers  
using the steps shown in the Speaker Setup  
section.  
Stereo-Direct (Bypass) Mode  
When the analog Stereo-Direct mode is selected  
by pressing the Stereo Mode Selector  
until SURROUNDOFFappears in the Main  
Information Display and the Surround  
Mode Indicator for Surround Off is lit, the  
J
SL  
SR  
LFE  
F
Delay Settings  
D
Only for the Dolby or DTS modes, you will need  
to adjust the delay time setting. Note that the  
delay time is not adjustable for any other modes.  
AVR will pass the analog source material directly  
through to the front left and right speakers,  
bypassing the digital processing circuitry.  
Surround Setup  
Once the speaker setup has been completed, the  
next setup step is to set the surround mode you  
wish to use with each input. Since surround  
modes are a matter of personal taste, feel free to  
select any mode you wish – you may change it  
later. To make it easier to establish the initial  
parameters for the AVR, it is best to leave the  
default setting of Logic 7 Music mode for most  
analog inputs and Dolby Digital for inputs con-  
nected to digital sources. In the case of inputs  
such as a CD Player, Tape Deck or Tuner, you may  
wish to set the mode to Stereo, if that is your  
preferred listening mode for standard stereo  
sources, where it is unlikely that surround encod-  
ed material will be used.  
Due to the different distances between the  
listening position for the front channel speakers  
and the surround speakers, the amount of time it  
takes for sound to reach your ears from the front  
or surround speakers is different. You may  
compensate for this difference through the use  
of the delay settings to adjust the timing for the  
specific speaker placement and acoustic  
conditions in your listening room or home  
theater.  
In this mode, the front left and right speakers  
will automatically be configured as LARGE; it  
is not possible to configure these speakers as  
SMALL.  
When the AVR is in the Stereo Bypass mode you  
may still configure the subwoofer output so that  
it is either turned off, with a full-range signal  
going to the front left/right speakers, or you may  
configure it so that the subwoofer feed is  
activated. The factory default setting is to have  
the subwoofer turned off for this mode, but you  
may change that setting by following these  
steps:  
The factory setting is appropriate for most  
rooms, but some installations create an uncom-  
mon distance between the front and surround  
speakers that may cause the arrival of front  
channel sounds to become disconnected from  
surround channel sounds.  
To set the surround mode you wish to use with  
the input selected, press the Surround Mode  
1. Press the Speaker Button  
9.  
Selector button  
6
on the front or cZon  
2. Press the OK Button  
A
to activate the  
the remote until the desired surround mode´s  
name appears in the Main Information  
configuration menu.  
K L  
/
3. Press the  
Buttons  
Z
on the remote  
Display  
F.  
to select the desired option. SUBNONEturns  
off the feed to the subwoofer, while SUB  
<L+R>turns it on.  
As the modes are changed, Indicator will  
illuminate next to the mode names in the  
Surround Mode Indicators  
D
on the front  
4. When the desired setting has been entered,  
panel.  
press the OK Button  
A
to return to normal  
operation.  
16 SYSTEM CONFIGURATION  
Download from Www.Somanuals.com. All Manuals Search And Download.  
System Configuration  
To resynchronize the front, center and surround  
channels, follow these steps:  
Next press the Night button  
When the button is pressed, the words  
O
on the remote.  
Before beginning the output level adjustment  
process, make certain that all speaker  
D-RANGE(Dynamic Range) followed by the  
current setting (MID, MAX, OFF) will appear in  
connections have been properly made. The  
system volume should be turned down at first.  
1. Measure the distance from the listening/  
viewing position to the front speakers in  
meters.  
the Main Information Display  
F. Press the  
For the easiest set-up, follow these steps while  
seated in the listening position that will be used  
most often:  
K L  
/
buttons  
Z
within five seconds to select  
the desired setting:  
2. Measure the distance from the listening/  
viewing position to the surround speakers.  
OFF: When OFF is shown in the display, the  
Night mode will not function.  
1. Make certain that all speaker positions have  
been properly configured for their “large” or  
“small” settings (as outlined above) and turn  
off the OSD system if it is in use.  
3. Press the Delay Button  
B.  
MID: When MID is shown in the display, a  
mild compression will be applied.  
4. When FRONTLDELAYappears in the  
Main Information Display  
F
press the OK  
Button  
A.  
2. Adjust the volume so that it is at -15, as  
shown in the on-screen display or Main  
MAX: When MAX is shown in the display, a  
more severe compression algorithm will be  
applied.  
K L  
5. Press the  
to enter the distance from the front left/right  
/
Buttons  
Z
on the remote  
Information Display  
F.  
speakers to your listening position. Press the OK  
To adjust and calibrate the output levels, follow  
these steps. For accurate calibration, it is a good  
idea to make these adjustments while seated in  
your favorite listening position. As the adjust-  
ment must be made for each surround mode, it  
is best to select any input associated with any  
Dolby Pro Logic II mode, make the adjustment  
for that surround mode, then step through all  
inputs you´re using (and thus through all sur-  
round modes associated with the inputs) and  
repeat the adjustment when any surround mode  
appears that has not yet been adjusted.  
When you want to use the Night mode feature,  
we recommend that you select the MID setting  
as a starting point and change to the MAX  
setting later, if desired.  
Button  
A
when this is complete.  
K L  
/
6. Press the  
Buttons  
Z
on the remote  
so that CENTERDELAYappears in the  
Main Information Display and press the  
OK Button (After CENTERDELAY,  
F
Output Level Adjustment  
A
Output level adjustment is a key part of the  
configuration process for any surround sound  
product. It is particularly important for a Dolby  
Digital receiver such as the AVR, as correct  
outputs will ensure that you hear sound tracks  
with the proper directionality and intensity.  
you will see FRONTRDELAY).  
K L  
/
7. Press the the  
Buttons  
Z
on the  
remote to enter the distance from the center  
speaker your listening position. Press the OK  
Button  
A
when this is complete.  
K L  
NOTE: Listeners are often confused about the  
operation of the surround channels. While some  
assume that sound should always be coming  
from each speaker, most of the time there will  
be little or no sound in the surround channels.  
This is because they are only used when a  
movie director or sound mixer specifically places  
sound there to create ambiance, a special effect  
or to continue action from the front of the room  
to the rear. When the output levels are properly  
set it is normal for surround speakers to oper-  
ate only occasionally. Artificially increasing the  
volume to the rear speakers may destroy the  
illusion of an enveloping sound field that  
duplicates the way you hear sound in a movie  
theater or concert hall.  
8. Press the  
/
Buttons  
Z
on the remote  
1. Select any input associated with any Dolby  
Pro Logic II surround mode by pressing the  
so that SURRDELAYRand after that  
SURRDELAYLappears in the Lower  
Display Line and press the OK Button  
Input Source Selector  
A
5
until the Pro  
A.  
Logic II Surround Mode Indicator  
D
on  
the frontdisplay lights up.  
K L  
9. Press the the  
/
Buttons  
Z
on the  
remote to enter the distance from the surround  
speakers to your listening position. Press the  
2. Press and hold the Tone button  
T
on the  
remote for more than 3 seconds. The words  
T-T FL 0DBwill appear in the Main  
OK Button  
A
when this is complete.  
Information Display  
F.  
10. When all adjustments have been made, the  
unit will return to normal operation in five  
seconds.  
3. The test noise will immediately begin to  
circulate in the speakers in a clockwise rotation,  
pausing at each position for two seconds. As the  
test noise rotates the speaker positions FL, C,  
FR, SR, SL(Front Left, Center, Front Right,  
Surround Right, Surround Left) will be shown in  
Night Mode Settings  
The Night mode is a feature of Dolby Digital that  
uses special processing to preserve the dynamic  
range and full intelligibility of a movie sound  
track while reducing the peak level. This prevents  
abruptly loud transitions from disturbing others,  
without reducing the sonic impact of a digital  
source. Note that the Night mode is only  
available when the Dolby Digital surround mode  
is selected.  
the Main Information Display  
F. As an  
IMPORTANT NOTE: The output level can be  
adjusted for each digital and analog surround  
mode separately. This allows you to compensate  
for level differences between speakers, that may  
also vary with the surround mode selected, or to  
increase or decrease the level of certain speakers  
intentionally, depending on the surround mode  
selected. Note that adjustments made for any  
surround mode are effective with all inputs  
associated with that surround mode.  
added assist, while the test noise is circulating,  
the proper channel position will also be indicat-  
ed in the Speaker/Channel Indicators  
5
by  
a blinking letter within the correct channel. Turn  
up the volume now until you can hear the noise  
clearly.  
To adjust the Night mode setting press the  
Input Source Selector  
on the remote and select an input that is associ-  
ated with a digital input and the Dolby Digital  
surround mode.  
A
on the front or  
5
SYSTEM CONFIGURATION 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
System Configuration  
IMPORTANT NOTE: Because this test noise will  
have a much lower level than normal music, the  
volume must be lowered after the adjustment  
for all channels is made, BEFORE you turn the  
test tone off.  
IMPORTANT NOTE: The Output level  
Once the settings outlined on the previous  
pages have been made, the AVR is ready for  
operation. While there are some additional  
settings to be made, these are best done after  
you have had an opportunity to listen to a  
variety of sources and different kinds of program  
material. These advanced settings are described  
on page 21 of this manual. In addition, any of  
the settings made in the initial configuration of  
the unit may be changed at any time.  
As you add new or different sources or speakers,  
or if you wish to change a setting to better  
reflect your listening taste, simply follow the  
instructions for changing the settings for that  
parameter as shown above. Note that any  
settings changed at any time, will be stored in  
memory in the AVR, also if it´s turned off  
completely, unless it will be reset (see page 34).  
Having completed the setup and configuration  
process for your AVR, you are about to  
adjustment made will be effective for the  
surround mode currently selected, also when  
other inputs are selected using the same  
surround mode. To adjust the output level with  
all other surround modes used, step through all  
inputs you´re using by pressing the Source  
NOTE: This is a good time to verify that the  
speakers have been properly connected. As the  
test noise circulates, listen to make certain that  
the sound comes from the speaker position  
shown in the Main Information Display. If the  
sound from a speaker location does NOT match  
the position indicated in the display, turn the  
Selector buttons  
appropriate Input Selectors  
A
on the front panel or the  
on the remote.  
5
When the indicator for any surround mode for  
which the level adjustment has not yet been  
made lights in the Main Information Display  
F
or its Indicator will illuminate in the  
AVR off using the Main Power Switch  
0
and  
Surround Mode Indicators field , repeat  
D
check the speaker wiring to make certain that  
each speaker is connected to the correct output  
terminal.  
the level adjustment described above. This will  
also allow you to compensate level differences  
between speakers, that may be different with  
each surround mode, or to increase or decrease  
the level of certain speakers intentionally,  
depending on the surround mode selected.  
After checking for speaker placement, let the  
test noise circulate again, and listen to see  
which channels sound louder than the others.  
Using the front left speaker as a reference, press  
K L  
experience the finest in music and home theater  
listening. Enjoy!  
the  
/
buttons  
Z
on the remote to bring  
all speakers to the same volume level. Note that  
K L  
/
when one of the  
buttons is pushed, the  
test noise circulation will pause on the channel  
being adjusted to give you time to make the  
adjustment. When you release the button, the  
circulation will resume after five seconds.  
Continue to adjust the individual speakers until  
they all have the same volume. Note that  
K L  
adjustments should be made with the  
/
buttons  
Z
on the remote only, NOT the main  
volume controls.  
When all channels have the same output level,  
turn the Volume  
I
7
down to about –40dB,  
otherwise the listening level may be too high as  
soon as the source’s music starts to play.  
Afterwards press the Tone Button  
T
button  
again to turn the test tone off and complete the  
process.  
18 SYSTEM CONFIGURATION  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation  
• During a listening session you may wish to  
adjust the Bass Control and Treble Control  
to suit your listening tastes or room acoustics.  
Basic Operation  
Source Selection  
Once you have completed the setup and  
configuration of the AVR, it is simple to operate  
and enjoy. The following instructions should be  
followed for you to maximize your enjoyment of  
your new receiver:  
• To select a source, press any of the  
Source Selector buttons on the remote  
• To set the output of the AVR so that the out-  
put is “flat,” with the Tone controls de-activated,  
5gh  
.
NOTE: After pressing the DVD Button  
must press the AVR Selector to have the  
remote control all of the AVR functions.  
5
you  
press the Tone Mode button  
T
button once  
h
or twice so that the words ToneOutappear  
momentarily in the Main Information Display  
Turning the AVR On or Off  
• When using the AVR for the first time, you must  
press the Main Power Switch  
panel to turn the unit on. This places the unit in a  
Standby mode, as indicated by the orange color of  
F
. To return the tone controls to an active con-  
• The input source may also be changed by  
pressing the front-panel Input Source  
0
on the front  
dition, press the Tone Mode button once  
T
or twice so that the words ToneInmomen-  
tarily appear in the Main Information Display  
Selector button  
A. Each press of the button  
will move the input selection through the list of  
available inputs.  
the Power Indicator  
Standby, you may begin a listening session by  
pressing the System Power Control or the  
Source button on the front panel or the AVR  
Selector . Note that the Power Indicator  
will turn blue. This will turn the unit on and  
2. Once the unit is in  
F
.
• To change the Bass or Treble Control settings  
press the Tone Mode Button until the  
words Bass or Treble appear momentarily in the  
Main Information Display . Press the OK  
1
• As the input is changed, the AVR will auto-  
matically switch to the digital input (if selected),  
surround mode and speaker configuration that  
were entered during the configuration process  
for that source.  
T
A
h
F
2
A B  
/
Button  
A
followed by the  
Buttons  
Z
return it to the input source that was last used.  
The unit may also be turned on from Standby by  
pressing any of the Source Selector buttons on  
to adjust the setting. When done, press the Tone  
• The front-panel Video 3 Inputs  
Digital 3 Input or the Coaxial Digital 3  
Input may be used to connect a device such  
H, Optical  
Mode Button  
T
again to exit the Tone Mode  
4
Menu.  
the remote 5gh  
.
G
• For private listening, plug the 6.3 mm stereo  
phone plug from a pair of stereo headphones  
NOTE: After pressing the the DVD Button  
to turn the unit on, press the AVR Selector  
to have the remote control all of the AVR func-  
tions.  
5
h
as a video game or camcorder to your home  
entertainment system on a temporary basis.  
into the front panel Headphone Jack  
3. Note  
• As the input source is changed, the new input  
name will appear in the Main Information  
that when the headphone’s plug is connected,  
the word HEADPHONEwill scroll once across  
To turn the unit off at the end of a listening  
session, simply press the System Power  
Display  
the selected input’s name in the front-panel  
Input Indicators  
F
and a green LED will light next to  
the Main Information Display  
F
and all  
speakers will be silenced. When the headphone  
plug is removed, the audio feed to the speakers  
will be restored.  
Control  
Off Button  
1
on the front panel or the Power  
on the remote.  
J
.
3
• When a pure audio input (CD, Tuner, Tape,  
6/8 Channel Input) is selected, the last video  
input used remains routed to the Video Out-  
puts 4Iand Video Monitor Output  
This permits simultaneous viewing and listening  
to different sources.  
When the remote is used to turn the unit “off” it  
is actually placing the system in a Standby mode,  
as indicated by the orange color of the Power  
• When the headphones are in use, you may  
take advantage of the Dolby Headphone modes  
to bring added spaciousness to headphone  
listening. Press the Dolby Mode Select  
B.  
Indicator  
2.  
Button  
Selector  
Q
6
or the Surround Mode Group  
to cycle through the three Dolby  
When you will be away from home for an  
extended period of time it is always a good idea  
to completely turn the unit off with the front  
• When a Video source is selected, its audio  
signal will be fed to the speakers and the video  
signal for that input will be routed to the  
Headphone modes to select the one that you  
prefer.  
panel Main Power Switch  
0.  
appropriate Monitor Output Jack  
be viewable on a TV monitor connected to the  
AVR. If a component video source is connected to  
B
and will  
Surround Mode Selection  
NOTE: All preset memories may be lost if the  
unit is left turned off with the Main Power  
One of the most important features of the AVR is  
its ability to reproduce a full multichannel  
surround sound field from digital sources, analog  
matrix surround encoded programs and standard  
stereo or even mono programs. In all, a total of  
fifteen listening modes are available on the AVR.  
Switch  
0
for more than two weeks.  
the Video 1  
Inputs, it will be routed to the Component  
Video Outputs . Make certain that your TV is  
F
or Video 2  
8
Component  
Using the Sleep Timer  
• To program the AVR for automatic turn-off,  
E
press the Sleep Button  
d
on the remote. Each  
set to the proper input to view the appropriate  
video signal (composite, S-Video or component  
video, see Notes for S-Video on page 13).  
press of the button will increase the time before  
shut down in the following sequence:  
Selection of a surround mode is based on  
personal taste, as well as the type of program  
source material being used.  
90  
80  
70  
60  
50  
min  
min  
min  
min  
min  
Controls and Use of Headphones  
40  
30  
20  
10  
OFF  
min  
min  
min  
min  
• Adjust the volume to a comfortable level using  
For example, motion pictures, CD’s or TV  
programs bearing the logo of one of the major  
surround encoding processes, such as Dolby  
Surround should be played in either the Dolby  
Pro Logic II Movie (with movies) or Music (with  
music) surround mode or with the  
Harman Kardon´s exclusive Logic 7 Movie Mode,  
to create a full range discrete 5.1 channel  
surround signal from surround encoded  
the front panel Volume Control  
Volume Up/Down buttons.  
I
or remote  
When the programmed sleep time has elapsed,  
the unit will automatically turn off (to Standby  
mode). Note that the front panel display will dim  
to one half brightness when the Sleep function  
is programmed. To cancel the Sleep function,  
7
• To temporarily silence all speaker outputs  
press the Mute button . This will interrupt  
4
the output to all speakers and the headphone  
jack, but it will not affect any recording or  
dubbing that may be in progress. Press the  
press and hold the Sleep Button  
d
until the  
information display returns to normal brightness  
and the SLEEPOFFmessage appears in the  
Mute button  
4
again to return to normal  
programs with a stereophonic left and right rear  
signal, just as it was recorded in real life (e.g.  
operation.  
Main Information Display  
F.  
OPERATION 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation  
sound being recorded from left rear side will be  
heard from that side only.  
Surround modes are selected using either the  
front panel controls or the remote. To select a  
surround mode from the front panel, press the  
Dolby Digital  
Dolby Digital (originally known as AC-3®) is a  
standard part of DVD, and is available on  
satellite broadcasts and is a part of the new  
high-definition television (HDTV) system.  
When no rear speakers are in use, the Dolby 3  
Stereo mode should be selected with all surround  
recordings.  
Surround Mode Group Selector Button  
to scroll through the list of available surround  
groups (for example, any Dolby mode or Logic 7  
mode). Next press the Surround Mode  
6
DTS  
Note that when Dolby Digital 2.0 signals (e.g.  
"D.D. 2.0" tracks from DVD), that are encoded  
with Dolby Pro Logic information, are received  
via any digital input, the Dolby Pro Logic II Movie  
mode will be selected automatically (in addition  
to the Dolby Digital mode) and will decode a full  
range 5.1 channel surround sound even from  
those recordings.  
DTS is another digital audio system that is  
capable of delivering 5.1 audio. Although both  
DTS and Dolby Digital are digital, they use  
different methods of encoding the signals, and  
thus they require different decoding circuits to  
convert the digital signals back to analog.  
Selector Button  
C
to choose the specific  
mode within the desired group (for example,  
within the Dolby mode group the options are  
Dolby Pro Logic, Dolby Pro Logic II Music, Dolby  
Pro Logic II Movies and Dolby 3 Stereo). To select  
a surround mode using the remote, any of the  
surround mode selector buttons IJK  
PQcuntil the desired mode appears. As  
you press the buttons, the Surround mode name  
will appear in the Main Information Display  
PCM Audio Playback  
PCM (Pulse Code Modulation) is the non-  
compressed digital audio system used for com-  
pact discs, and some special PCM encoded DVDs.  
The digital circuits in the AVR are capable of high  
quality digital-to-analog decoding, and they may  
be connected directly to the digital audio output  
of your CD/DVD player.  
To create wide, enveloping sound field  
environments and defined pans and flyovers with  
all analog stereo recordings select the Dolby Pro  
Logic II Music mode or Harman Kardon’s  
exclusive Logic 7 Music mode for a dramatic  
improvement in comparison to the Dolby Pro  
Logic (I) mode of former times.  
F
. As the surround mode changes, a blue LED  
will light next to the current mode in the  
Surround Mode Indicators list on the  
D
front panel. Regard that any time a surround  
mode is changed it remains associated with the  
input just selected until another choice is made.  
Connections may be made to the Optical or  
Coaxial inputs 9L on the rear panel or front  
NOTE: Once a program has been encoded with  
matrix surround information, it retains the  
surround information as long as the program is  
broadcast in stereo. Thus, movies with surround  
sound may be decoded via any of the analog sur-  
round modes such as Dolby Pro Logic II or Logic 7,  
when they are broadcast via conventional TV  
stations, cable, pay TV and satellite transmission.  
In addition, a growing number of made-for-televi-  
sion programs, sports broadcasts, radio dramas  
and music CDs are also recorded in surround  
sound. You may view a list of these programs at  
the Dolby Laboratories Web site at  
NOTE: The name of each Surround Mode will  
scroll through the Main Information Display  
panel 4G  
.
To listen to a PCM digital source, first select the  
input for the desired source (e.g., CD) to feed its  
video signal (if any) to the TV monitor and to  
provide its analog audio signal for recording.  
F
while the modes are being selected. To avoid  
exiting from the surround mode selection  
K L  
/
process, be certain to push the  
buttons  
Z
while a mode name is still visible.  
Next press the Digital Select button  
Y
and  
K L  
Note that the Dolby Digital or DTS modes may  
only be selected when a digital input is in use. In  
addition, when a digital source is present, the  
AVR will automatically select and switch to the  
correct mode (Dolby Digital or DTS), regardless of  
the mode that has been previously selected. For  
more information on selecting digital sources, see  
the following section of this manual.  
then use the  
/
buttons  
Z
on the remote  
until the desired choice appears in the Main  
Information Display , then press the OK  
button to confirm the choice.  
F
A
When a PCM source is playing, a brief message  
PCM will appear in the Main Information  
Even when a program is not listed as carrying  
intentional surround information, you may find  
that the Dolby Pro Logic II, Dolby 3 Stereo or  
Logic 7 modes often deliver enveloping surround  
presentations through the use of the natural  
surround information present in all stereo  
recordings.  
Display  
F. During PCM playback you may  
select any surround mode except Dolby Digital or  
DTS.  
To listen to a program in traditional two channel  
stereo, using the front left and front right  
speakers only (plus the subwoofer if installed and  
configured), follow the instructions shown above  
for using the remote until SURROFFappears  
in the Main Information Display  
F.  
However, for stereo programs without any  
surround information the Theater, Hall and 5CH  
Stereo modes should be tried (effective particularly  
with old ”extreme” stereo recordings) and for  
mono programs, we suggest that you try the  
Theater or Hall modes.  
Digital Audio Playback  
Digital audio is a major advancement over older  
analog matrix surround systems. It delivers five  
discrete channels: left front, center, right front, left  
surround and right surround. Each channel  
reproduces full frequency range (20Hz to 20kHz)  
and offers dramatically improved dynamic range  
and significant improvements to signal-to-noise  
ratios. In addition, digital systems have the  
capability to deliver an additional channel that is  
specifically devoted to low frequency information.  
This is the “.1” channel referred to when you see  
these systems descibed as “5.1”. The bass channel  
is separate from the other channels, but since it is  
intentionally bandwidth limited, sound designers  
have given it that unique designation.  
20 OPERATION  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation  
The last number indicates if there is a discrete  
Low Frequency Effects (LFE) channel. This is the  
“.1” in the common abbreviation of “5.1” sound  
and it is a special channel that contains only bass  
frequencies.  
Selecting a Digital Source  
Surround Mode Types  
To utilize either digital mode you must have  
properly connected a digital source to the AVR.  
Connect the digital outputs from DVD players,  
HDTV receivers, satellite systems or CD players to  
the Optical or Coaxial inputs on the rear or  
front panel 9L4G. In order to provide a  
backup signal and a source for analog stereo  
recording, the analog outputs provided on digital  
source equipment should also be connected to  
their appropriate inputs on the AVR rear panel  
(e.g., connect the analog stereo audio output  
For Dolby Digital and DTS sources, a three digit  
indication will appear, showing the number of  
channels present in the data. An example of this  
type of display is 3/2/.1.  
• A .1 tells you that an LFE channel is present.  
This will be displayed for Dolby Digital 5.1 and  
DTS 5.1 programs, as available.  
The first number indicates how many discrete  
front channel signals are present.  
• A 0 indicates that there is no LFE channel  
information available. However, even when  
there is no dedicated LFE channel, low  
frequency sound will be present at the  
subwoofer output when the speaker  
configuration is set to show the presence of  
subwoofer.  
• A 3 tells you that separate front left, center and  
front right signals are available. This will be  
displayed for Dolby Digital 5.1 and DTS 5.1  
programs.  
from a DVD to the DVD inputs  
5
on the rear  
• A 2 tells you that separate front left and right  
signals are available, but there is no discrete  
center channel signal. This will be displayed for  
Dolby Digital bit streams that have stereo  
program material.  
panel when you connect the source’s digital  
outputs).  
An UNLOCKmessage may appear in the  
When playing a digital source such as DVD, first  
select its input using the remote or front panel  
controls as outlined in this manual in order to  
feed its video signal (if any) to the TV monitor  
and to provide its analog audio signal for  
recording. When the digital input appropriate  
with the DVD player is not selected automatically  
(due to the input settings made earlier during the  
system configuration, see page 14), select the  
digital source by pressing the Digital Input  
K L  
Lower Display Line  
F. This is your indication  
that the digital audio data stream has been inter-  
rupted or is no longer present. When that occurs,  
the unit’s digital signal processor has no signal to  
lock onto, and is thus “unlocked.” You may see  
this message when a DVD is first started until the  
stream is playing and the processor determines  
which mode to apply; or any time the data  
stream is stopped or paused, such as when the  
menus of some discs are displayed or when the  
player is switching between the different sections  
of a disc. You may also see the message when a  
satellite receiver, cable set-top or HDTV tuner is  
in use if the digital audio is temporarily  
interrupted when channels are changed or when  
a cable box switches from a channel with a  
digital data stream to a channel with analog  
audio only. The UNLOCKmessage is normal,  
and does not indicate any problem with your  
receiver. Rather, it tells you that the incoming  
data has simply been paused or is not present for  
a variety of possible reasons.  
• A 1 tells you that there is only a mono channel  
available in the Dolby Digital bitstream.  
The middle number indicates how many discrete  
surround channel signals are present.  
• A 2 tells you that separate surround left and  
right signals are available. This will be  
displayed for Dolby Digital 5.1 and DTS 5.1  
programs.  
Selector button  
Y
and then using the  
/
buttons  
Z
on the remote to choose any of the  
OPTICAL(OPT)or COAXIAL  
(COAX)inputs, as they appear in the Main  
• A 1 tells you that there is only a single,  
surround encoded surround channel. This will  
appear for Dolby Digital bit streams that have  
matrix encoding.  
Information Display  
F. When the digital  
source is playing, the AVR will automatically  
detect whether it is a multichannel Dolby Digital,  
DTS source or a conventional PCM signal, which  
is the standard output from CD players.  
• A 0 indicates that there is no surround channel  
information. This will be displayed for two-  
channel stereo programs.  
Digital Status Indicators  
When a digital source is playing, the AVR senses  
the type of bitstream data that is present. Using  
this information, the correct surround mode will  
automatically be selected. For example, DTS bit-  
streams will cause the unit to switch to DTS  
decoding, and Dolby Digital bitstreams will enable  
Dolby Digital decoding. When the unit senses  
PCM data, from CDs and LDs and some music  
DVDs or certain tracks on normal DVDs, it will  
allow the appropriate surround mode to be  
selected manually. Since the range of available  
surround modes depends on the type of digital  
data that is present, the AVR uses a variety of  
indicators to let you know what type of signal is  
present. This will help you to understand the  
choice of modes and the input channels recorded  
on the disc.  
When Dolby Digital 3/2/.1 or DTS 3/2/.1 signals  
are being played, the AVR will automatically  
switch to the proper surround mode, and no  
other processing may be selected. When a Dolby  
Digital signal with a 3/1/0 or 2/0/0 signal is  
detected you may select any of the Dolby  
surround modes.  
It is always a good idea to check the readout for  
the channel data to make certain that it matches  
the audio logo information shown on the back of  
a DVD package. In some cases you will see  
indication for “2/0/0” even when the disc  
contains a full 5.1, or 3/2/.1 signal. When this  
happens, check the audio output settings for  
your DVD player or the audio menu selections for  
the specific disc being played to make certain  
that the player is sending the correct signal to  
the AVR.  
When a digital source is playing, the AVR will  
display a variety of messages to indicate the type  
of bitstream received. These messages will  
appear shortly after an input or surround mode is  
changed, and will remain in the Main  
In addition to the Bitstream Indicators, the  
AVR features a set of unique channel input indi-  
cators that tell you how many channels of digital  
information are being received and if the digital  
signal is interrupted.  
Information Display  
F
for about five  
seconds before the display returns to the normal  
surround mode indication.  
OPERATION 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation  
These indicators are the L/C/R/SL/SR/LFE letters  
that are inside the center boxes of the  
Speaker/Channel Input Indicators in the  
channel signal of that source, the ”Downmix” to  
Stereo or Dolby Surround, can be recorded by  
connecting its analog audio outputs to the  
appropriate analog inputs (e.g. DVD) of the AVR,  
even if the digital input of the AVR remains  
selected. Additionally, the digital signals will be  
passed through to the Digital Audio  
Night Mode  
A special feature of Dolby Digital is the Night  
mode, which enables Dolby Digital input sources  
to be played back with full digital intelligibilty  
while reducing the maximum peak level and  
lifting the low levels by 1/4 to 1/3. This prevents  
abruptly loud transitions from disturbing others  
without reducing the impact of the digital source.  
The Night mode is available only when Dolby  
Digital mode is selected.  
front panel  
5. When a standard analog stereo  
or matrix surround signal is in use, only the “L”  
and “R” indicators will light, as analog signals  
have only left and right channels, respectively,  
even surround recordings, carry surround  
Outputs  
8.  
information on the left and right channels only.  
Tape Recording  
Digital signals, however, may have one to six  
separate channels, depending on the program  
material, the method of transmission and the  
way in which it was encoded. When a digital  
signal is playing, the letters in these indicators  
will light in response to the specific signal being  
received. It is important to note that although  
Dolby Digital, for example, is referred to as a  
“5.1” system, not all Dolby Digital DVD or audio  
tracks selected on DVD or other Dolby Digital  
programs are encoded for 5.1. Thus, it is some-  
times normal for a DVD with a Dolby Digital  
soundtrack to trigger e.g. only the “Land “R”  
indicators.  
In normal operation, the audio or video source  
selected for listening through the AVR is sent to  
the record outputs. This means that any program  
you are watching or listening to may be recorded  
simply by placing machines connected to the out-  
The Night mode may be engaged when a Dolby  
Digital DVD is playing by pressing the Night  
K L  
Button  
O
on the remote. Next, press the  
/
buttons  
Z
to select either the middle range or  
full compression versions of the Night mode. To  
turn the Night mode off, press the  
puts for Tape Outputs  
1
or Video 1 Outputs  
K L  
/
buttons  
4I in the record mode.  
Z
until the message in the lower third of the  
video display and the Main Information  
Display reads D-RANGEOFF.  
Output Level Trim Adjustment  
F
Normal output level adjustment for the AVR is  
established using the test tone, as outlined on  
page 17. In some cases, however, it may be  
desirable to adjust the output levels using  
program material such as a test disc, or a  
selection you are familiar with. Additionally, the  
output level for the subwoofer can only be  
adjusted using this procedure.  
The Night mode may also be selected to always be  
on at either level of compression as soon as the  
Dolby Digital mode is turned on using the options  
in the Night Mode settings. See above for  
information on using this option.  
The letters used by the Speaker/Channel Input  
Indicators  
5
also flash to indicate when a  
IMPORTANT NOTES ON DIGITAL PLAYBACK:  
1. When the digital playback source is stopped,  
or in a pause, fast forward or chapter search  
mode, the digital audio data will momentarily  
stop, and the channel position letters inside the  
bitstream has been interrupted. This will happen  
when a digital input source is selected before the  
playback starts, or when a digital source such as  
a DVD is put into a Pause mode. The flashing  
indicators remind you that the playback has  
stopped due to the absence of a digital signal  
and not through any fault of the AVR. This is  
normal, and the digital playback will resume  
once the playback is started again.  
To adjust the output levels using program  
material, first select the surround mode for which  
you want to trim the speakers (see NOTE below)  
by selecting the appropriate input, associated  
with the desired surround mode, start your  
program material source and set the reference  
volume for the front left and front right channels  
Speaker/Channel Indicators  
5
will flash.  
This is normal and does not indicate a problem  
with either the AVR or the source machine. The  
AVR will return to digital playback as soon as the  
data is available and when the machine is in a  
standard play mode.  
using the Volume Control  
I7.  
2. Although the AVR will decode virtually all DVD  
movies, CDs and HDTV sources, it is possible that  
some future digital sources may not be  
compatible with the AVR.  
Once the reference level has been set, press the  
Channel Select button and note that  
FRONTLLEVELwill appear in the Main  
Information Display for five seconds. To  
a
F
change the level, first press the OK button  
A,  
3. Note that not all digitally encoded programs  
and not all audio tracks on a DVD contain full  
5.1-channel audio. Consult the program guide  
that accompanies the DVD to determine which  
type of audio has been recorded on the disc. The  
AVR will automatically sense the type of digital  
surround encoding used and adjust to  
K L  
and then use the  
/
buttons  
Z
to raise or  
lower the level. DO NOT use the volume control,  
as this will alter the reference setting.  
Once the change has been made, press the OK  
K L  
/ buttons  
button  
A
and then press the  
Z
to select the next output channel location  
accommodate it.  
that you wish to adjust. To adjust the subwoofer  
4. When a Dolby Digital or DTS source is playing,  
you normally may not be able to select some of  
the analog surround modes such as Dolby Pro  
Logic II, Dolby 3 Stereo, Hall, Theater, 5CH Stereo  
or Logic 7, except with special audio tracks  
(see indication ”Dolby Digital” on previous page)  
or data format selected (see ”PCM” on previous  
page).  
K L  
/
level, press the  
buttons  
Z
until  
WOOFERLEVELappears in the Main  
Information Display (only available if the  
F
subwoofer was selected during the speaker  
configuration, page 14).  
5. When a Dolby Digital or DTS source is playing,  
it is not possible to make an analog recording  
using the Tape  
1
or Video 1  
4
record  
outputs, if the source is connected to any digital  
input of the AVR only. But the analog two  
22 OPERATION  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation  
Press the OK button  
desired channel appears in the Main  
Information Display and on-screen display,  
and follow the instructions shown above to  
adjust the level.  
A
when the name of the  
When the button is pressed so that MANUAL  
Memory Backup  
appears in the Main Information Display  
each tap of the Selector will increased or  
decrease the frequency by one increment. When  
the tuner receives a strong enough signal for  
adequate reception, MANAULTUNEDwill  
F
This product is equipped with a memory backup  
system that preserves tuner presets and system  
configuration information if the unit is turned off  
completely, accidentally unplugged or subjected  
to a power outage. This memory will last for  
approximately 1 week, after which time all  
information must be reentered.  
F
Repeat the procedure as needed until all  
channels requiring adjustment have been set.  
When all adjustments have been made press the  
appear in the Main Information Display  
F.  
4. Stations may also be tuned directly by pressing  
OK button  
A
twice, the AVR will return to  
the Direct button , and then pressing the  
V
normal operation.  
Numeric Keys that correspond to the  
X
Tuner Operation  
station’s frequency. The desired station will  
automatically be tuned after the latest number is  
entered. If you press an incorrect button while  
entering a direct frequency, press the Clear  
NOTE: The output levels may be separately  
trimmed for each digital and analog surround mode.  
If you wish to have different trim levels for a specific  
mode, select that mode and then follow the  
instructions in the steps shown above.  
The AVR’s tuner is capable of tuning AM, FM and  
FM Stereo broadcast stations and receiving RDS  
data. Stations may be tuned manually, or they  
may be stored as favorite station presets and  
recalled from a 30 position memory.  
button  
D
to start over.  
NOTE: When the FM reception of a stereo station  
is weak, audio quality will be increased by  
switching to Mono mode by pressing the Tuner  
Changing the levels by the trim adjustment as  
described above will automatically change the  
level settings shown during the Output Level  
Adjustment (see page 22) correspondingly (and  
vice versa) and will remain in the AVR´s memory  
system, even when the unit is turned off. With  
Stereo modes the adjustment procedure  
described above is the only way to trim the out-  
put level.  
Station Selection  
1. Press the AM/FM Tuner Select button  
on the remote to select the tuner as an input. The  
tuner may be selected from the front panel by  
g
Mode button  
Band Selector  
MANUALappears momentarily in the Main  
W
on the remote or holding the  
8
on the front panel so that  
either pressing the Input Source Selector  
until the tuner is active or by pressing the Tuner  
Band Selector at any time.  
A
Information Display  
F
and then goes out.  
Preset Tuning  
8
Using the remote, up to 30 stations may be  
stored in the AVR’s memory for easy recall using  
the front panel controls or the remote.  
2. Press the AM/FM Tuner Select button  
Tuner Band Selector again to switch  
between AM and FM so that the desired  
frequency band is selected.  
g
or  
6-Channel Direct Input  
8
The AVR is equipped for future expansion  
To enter a station into the memory, first tune the  
station using the steps outlined above. Then:  
through the use of optional, external adapters for  
formats that the AVR may not be capable of  
processing. When an adapter is connected to the  
3. Press the Tuner Mode button  
remote or hold the Band Selector  
front panel pressed for 3 seconds to select manual  
or automatic tuning.  
W
on the  
on the  
1. Press the Memory button  
Note that two underscore lines will appear in the  
Main Information Display  
C
on the remote.  
8
6-Channel Direct Input  
by pressing the 6-Ch Direct Input Selector  
. The 6-Channel Direct Input may also be  
selected by pressing the Input Source Selector  
button on the front panel until the words  
6CHDIRECT appear in the Main  
Information Display , and a blue LED lights  
next to 6 CH in the Input Indicators  
N, you may select it  
F
.
f
2. Within five seconds, press the Numeric Keys  
corresponding to the location where you  
When the button is pressed so that AUTO  
appears in the Main Information Display  
each press of the Tuning Selectors  
X
F
A
wish to store this station’s frequency. Once  
entered, the preset number will appear in the  
7
U
will  
put the tuner in a scan mode that seeks the next  
higher or lower frequency station with acceptable  
signal strength. An AUTOSTTUNED  
indication will momentarily appear when the  
station stops at a stereo FM station, and an  
AUTOTUNEDindication will momentarily  
appear when an AM or monaural FM station is  
tuned. Press the Tuning buttons again to scan to  
the next receivable station.  
F
Main Information Display  
F.  
J
.
3. Repeat the process after tuning any additional  
stations to be preset.  
Note that when the 6-Channel Direct Input is in  
use, you may not select a surround mode, as the  
external decoder determines processing. In  
addition, there is no signal at the record outputs  
when the 6-Channel Direct Input is in use.  
Recalling Preset Stations  
• To manually select a station previously entered  
in the preset memory, press the Numeric Keys  
X
that correspond to the desired station’s  
Display Brightness  
memory location.  
The AVR’s front panel Main Information  
• To manually tune through the list of stored  
preset stations one by one, press the Preset  
Display  
F
is set at a default brightness level  
that is sufficient for viewing in a normally lit  
room. However, in some home theater  
installations, you may wish to occasionally lower  
the brightness of the display, or turn it off  
completely.  
Stations Selector buttons  
panel or remote.  
9
E
on the front  
You can also adjust the Display Brightness by  
pressing the Dim Button  
control. Note that the blue lighting inside the  
volume control and the Power Indicator  
L
on the remote  
2
will remain lit at normal brightness to remind you  
that the unit is still turned on.  
OPERATION 23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation  
Program Search (PTY)  
RDS Operation  
An important feature of RDS is its capability of  
encoding broadcasts with Program Type (PTY)  
codes that indicate the type of material being  
broadcast.  
The AVR is equipped with RDS (Radio Data  
System), which brings a wide range of  
information to FM radio. RDS is a system for  
transmitting station call signs or network infor-  
mation, a description of station program type,  
text messages about the station or specifics of a  
musical selection, and the correct time.  
You may search for a specific Program Type  
(PTY) by following these steps:  
1. Press the RDS button  
current PTY is shown in the Main Information  
Display  
B
F
until the  
RDS Tuning  
F
.
When an FM station is tuned in and it contains  
RDS data, the AVR will automatically display the  
station’s call sign or other program service in the  
2. While the PTY is shown, press the Preset  
Up/Down button or hold them pressed  
9
E
Main Information Display  
F.  
to scroll through the list of available PTY types,  
as shown above. To simply search for the next  
station transmitting any RDS data, use the  
RDS Display Options  
The RDS system is capable of transmitting a  
wide variety of information in addition to the  
initial station call sign that appears when a  
station is first tuned. In normal RDS operation  
the display will indicate the station name,  
broadcast network or call letters. Pressing the  
Preset Up/Down button  
9
E
until RDS  
ONLYappears in the display.  
3. Press any of the Tuning Up/Down buttons  
, the tuner begins to scan the FM band  
7
U
upwards or downwards for the first station that  
has RDS data that matches the desired  
selection, and acceptable signal strength for  
quality reception.  
RDS button  
B
F
enables you to cycle  
through the various data types in the following  
sequence:  
4. The tuner will make up to one complete scan  
of the entire FM band for the next station that  
matches the desired PTY type and has  
acceptable reception quality. If no such station  
is found, the display will read NONEfor some  
seconds and the tuner will return to the last FM  
station in use before the search.  
• The station’s call letters (with some private  
stations other information too).  
• The station’s frequency (FREQ).  
• The Program Type (PTY)as shown in the list  
below.  
• A “text” message (Radiotext, RT) containing  
special information from the broadcast station.  
Note that this message may scroll across the  
display to permit messages longer than the eight  
positions in the display. Depending on signal  
quality, it may take up to 30 seconds for the text  
message to appear; in that time, the word  
TEXTwill flash in the Information Display  
when RT is selected.  
NOTE: Many stations do not transmit a specific  
PTY. The display will show NONE, when such a  
station is selected and PTY is active.  
NOTE: Some stations transmit constant traffic  
information. These stations can be found by  
selecting TRAFFIC. The AVR will find the appro-  
priate station, even if it is not broadcasting traf-  
fic information when the search is made.  
• The current time of day (CT). Note that it may  
take up to two minutes for the time to appear,  
in that time the word TIMEwill flash in the  
information display when CT is selected. Please  
note that the accuracy of the time data is  
dependent on the radio station, not the AVR.  
Some RDS stations may not include some of  
these additional features. If the data required  
for the selected mode is not being transmitted,  
the Main Information Display  
F
will show  
a NOTYPE, NOTEXTor NOTIME  
message after the individual time out.  
In any FM mode the RDS function requires a  
strong enough signal for proper operation.  
24 OPERATION  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting Guide  
SYMPTOM  
CAUSE  
SOLUTION  
Unit does not function when  
• No AC Power  
• Make certain AC power cord is plugged  
into a live outlet  
Main Power Switch  
0
is pushed  
• Check to see if outlet is switch controlled  
Display lights, but no sound  
or picture  
• Intermittent input connections  
• Make certain that all input and speaker  
connections are secure  
Mute is on  
• Press Mute button  
4
• Volume control is down  
• Turn up volume control  
Sound is heard, but Front-Panel  
Display does not light  
• Display brightness is turned off  
• Follow the instructions in the Display Brightness section  
on page 23 so that the display is set to VFD FULL  
No sound from any speaker;  
light around Power switch  
• Amplifier is in protection mode  
due to possible short  
• Check speaker-wire connections for shorts at receiver  
and speaker ends  
1
is red  
• Amplifier is in protection mode  
due to internal problems  
• Contact your local Harman Kardon service depot  
No sound from surround or  
center speakers  
• Incorrect surround mode  
• Incorrect configuration  
• Select a mode other than Stereo  
• Check speaker mode  
• Stereo or Mono program material  
• With (analog or digital) Dolby surround modes, the surround  
decoder may not create rear-channel  
information from non-encoded programs  
• Check speaker-wire connections or use test tone  
to verify connections (see page 20)  
• Speakers not properly connected  
Unit does not respond to  
remote commands  
• Weak batteries in remote  
• Wrong device selected  
• Change remote batteries  
• Press the AVR selector  
h
Remote sensor  
E
is obscured  
• Make certain front-panel sensor is visible to remote or  
connect remote sensor  
Intermittent buzzing in tuner  
• Local interference  
• Move unit or antenna away from computers, fluorescent lights,  
motors or other electrical appliances  
Letters flash in the Channel Indicator  
Display and Digital Audio stops  
• Digital audio feed paused  
• Resume play for DVD  
• Check that Digital Signal is fed to the Digital Input selected  
T
To clear the AVR’s entire system memory  
including tuner presets, output level settings,  
delay times and speaker configuration data, first  
NOTE: Resetting the processor will erase any  
configuration settings you have made for  
speakers, output levels, surround modes, digital  
input assignments as well as the tuner presets.  
After a reset the unit will be returned to the  
factory presets, and all settings for these items  
must be reentered.  
Processor Reset  
In the rare case where the unit’s operation or the  
displays seem abnormal, the cause may involve  
the erratic operation of the system’s memory or  
microprocessor.  
put the unit in Standby by pressing the System  
Power Control button  
1. Next, press and  
hold the Surround Mode Button  
onds.  
6
for 5 sec-  
To correct this problem, first unplug the unit  
from the AC wall outlet and wait at least three  
minutes. After the pause, reconnect the AC  
power cord and check the unit’s operation. If the  
system still malfunctions, a system reset may  
clear the problem.  
The unit will turn on automatically. Note that  
once you have cleared the memory in this man-  
ner, it is necessary to re-establish all system  
configuration settings and tuner presets.  
If the system is still operating incorrectly, there  
may have been an electronic discharge or severe  
AC line interference that has corrupted the  
memory or microprocessor.  
If these steps do not solve the problem, consult  
an authorized Harman Kardon service depot.  
TROUBLESHOOTING GUIDE 25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD 28 Digital Versatile Disc Player  
Terminology  
HDMI(High-Definition Multimedia  
Multiple Angle: DVDs have the capability to  
show up to four different views of the same  
scene in a program. When a disc is encoded with  
multiple-angle information, pressing the Angle  
button will enable you to switch between these  
different views. Note that at present, few discs  
take advantage of this capability and, when they  
do, the multiple-angle technology may only be  
present for short periods of time within the disc.  
Producers will usually insert some sort of icon or  
graphic in the picture to alert you to the  
Terminology  
Interface): HDMI is a serial-bus form of com-  
munication between the DVD player and the  
video display or audio/video receiver. With 5Gbps  
of bandwidth, it is capable of passing uncom-  
pressed digital audio and high-definition digital  
video using a single cable. With HDMI, the  
DVD 28 is capable of outputting high-resolution  
(720p or 1080i) video and 5.1-channel Dolby  
Digital or DTS digital audio, with the convenience  
of just a single cable connection.  
Since they share some of the characteristics and  
technology of CD players, many of the terms and  
operational concepts used in a DVD player are  
similar to what you may be familiar with from CD  
players and changers, or older video disc formats  
such as Laser Disc. However, if this is your first  
DVD product, some of the terms used to describe  
the features of a DVD player may be unfamiliar.  
The following explanations should solve some of  
the mysteries of DVD, and help you to enjoy all  
the power and flexibility of the DVD format and  
the DVD.  
availability of multiple viewing angles.  
JPEG Files: JPEG stands for the Joint  
Photographic Experts Group, which developed a  
standard for compressing still images, such as  
photographs. JPEG files may be created on a  
personal computer by importing images from a  
digital camera, or scanning printed photographs.  
These files may be burned onto a compact disc.  
The DVD 28 is capable of recognizing JPEG files  
and enabling you to view them on your video  
screen.  
Reading: This is a message that you will see  
after you´ve loaded the disc and the tray has  
closed. It refers to the fact that the player must  
first examine the contents of the disc to see if it  
is a CD or DVD, and then extract the information  
about the type of material on the disc, such as  
languages, aspect ratios, subtitles, number of  
titles and more. The slight delay while the  
contents of the disc are read is normal.  
With the arrival of DVD, disc data capacity has  
increased dramatically. On a DVD Video disc most  
of this capacity is taken up by MPEG 2 video and  
the multichannel movie soundtrack in Dolby  
Digital and/or DTS. This information is  
compressed.  
Aspect Ratio: This is a description of the width  
of a video image in relation to its height.  
A conventional video screen is four units wide for  
every three units of height, that’s why the ratio is  
called ”4:3”. Newer wide aspect ratio video  
displays are 16 units wide for every nine units of  
height, making them more like the screen in a  
movie theater. The program material on a DVD  
may be recorded in either format and, in  
addition, you may configure the DVD to play  
back in either format, depending on the features  
recorded on a disc.  
Title: For a DVD, a title is defined as an entire  
movie or program. There can be as many chapters  
within a title as the producers decide to include.  
Most discs include only one title, but some may  
have more than one, to give you a “Double  
Feature” presentation.  
Resume: The operation of the Stop Button on  
the DVD works differently from what you are  
used to on CD players. On a traditional CD  
player, when you press the Stop button, the unit  
does just that: it stops playback. On a CD player,  
when you press the start button again, the disc  
starts from the beginning. With the DVD,  
however, you have two options when playing  
DVD discs. Pressing Stop once will stop playback,  
but it actually puts the unit in the Resume mode.  
This means that you can turn the machine off  
and, when you press play the next time, the disc  
will resume or continue from the point on the  
disc where the Stop button was pressed. This is  
helpful if you are watching a movie and must  
interrupt your viewing session but wish to pick  
up where you left off. Pressing the Stop button  
twice will stop the machine in a traditional  
manner and, when the disc is played again, it will  
start from the beginning.  
Chapter: DVD programs are divided into  
chapters and titles. Chapters are the sub-sections  
programmed into a single title on a disc.  
Chapters may be compared to the individual  
tracks on an audio CD.  
Component Video: This form of video signal  
eliminates many of the artifacts of traditional  
composite video signals by splitting the signal  
into a separate luminance channel (the “Y” sig-  
nal channel) and two color-difference signals (the  
Pr and Pb signal channels). With a component  
video connection, you will see greater picture  
resolution and eliminate many picture imperfec-  
tions such as the moiré patterns often seen on  
check-patterned cloth. However, in order to ben-  
efit from component video, you must have a  
video display with Y/Pr/Pb component video  
inputs. Do not connect the component video out-  
puts of the DVD 28 to the standard composite or  
S-video inputs of a TV or recorder.  
Progressive Scan: Due to the immense data  
storage capacity of DVD, images are nowadays  
stored progressively (intact, rather than inter-  
laced). This allow all of the lines in each frame  
(odd and even) to be shown at the same time.  
Harman Kardon Cinema Lounge comes with true  
progressive scan video output resulting in a 40%  
greater light output than a conventional TV and  
a stunningly detailed, high definition image with  
absence of visible scanlines and motion artifacts.  
WMA Files: WMA (Windows Media® Audio) is  
an audio compression format that was developed  
by the Microsoft® Corporation for use with its  
Windows Media Player. WMA files can be even  
smaller in size than MP3 files, while maintaining  
similar quality. The DVD 28 is among those DVD  
players capable of playing discs containing WMA  
files. Note that Windows Media Player uses other  
file formats; however, the DVD 28 is only capable  
of playing files that end in the “.wma” extension.  
See page 5 for more information on WMA file  
support.  
In resume mode, the cover of the DVD will be  
displayed, if available. Otherwise, the  
Harman Kardon screen will appear.  
DivX  
DivX is the name of a revolutionary new video  
codec which is based on the MPEG-4 compres-  
sion standard for video. This DVD player will play-  
back discs created with DivX software. The DVD  
player’s playback functionalities of DivX video  
discs will vary depending on the DivX software  
version used for creating your movies. For more  
information about the different software versions  
HDCP (High-Bandwidth Digital Content  
Protection): HDCP is the specification for pro-  
tecting digitally encoded content from unautho-  
rized copying when it is transmitted from a DVD  
player (or other video source) to a video display  
using HDMI or DVI connections. In order to take  
advantage of the high-resolution output of the  
DVD 28 via its HDMI output, your display must  
be HDCP-compliant. Virtually all displays with  
HDMI inputs are HDCP-compliant, but not all  
DVI-equipped displays are. If you are using the  
DVD 28 with an optional HDMI-to-DVI cable or  
adapter, check the owner’s manual for your dis-  
play to determine whether it is HDCP-compliant.  
26 TERMINOLOGY  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Features  
The DVD 28 will NOT play the following:  
• DVD discs with a Region Code other than 2  
High quality video  
Compatible with CD  
as well as DVD  
• High Definition Multimedia Interface (HDMI)  
for a single wire, digital connection to your  
HD-Ready screen.  
• DVD-ROM data discs  
• DVD-RAM discs  
• CD-I discs  
• The DVD 28 will play any conventional Audio  
CD or recordable (CD-R) or erasable CD  
(CD-RW), MP3, WMA (v8) or any DivX or VCD  
or DVD/Video with the region code 0 or 2.  
• Advanced sophisticated 10-bit MPEG-2 video  
decoding circuits.  
• CD-G discs  
• Direct RGB output via SCART (selectable) for  
optimum video performance. SCART connector  
also configurable for Composite Video output.  
Disc formats supported  
by this player  
• SVCD discs  
• Kodak Photo CDdiscs (Kodak Picture CD  
discs, available to consumers, may be viewed  
using the DVD 28).  
The unit can play the following disc formats  
(8 cm and 12 cm size):  
• DVD-AUDIO  
• DVD  
• DVD-R  
• DVD-RW  
• DVD+R  
• DVD+RW  
• CD  
• Test screen videos available for testing video  
performance and setup.  
• Discs intended for use in video game consoles  
• Pure PAL with NTSC disc due to true  
NTSC/PAL conversion.  
• Discs recorded in the “VR” mode or at any  
speed other than “SP”  
• Dual-layer compatibility for extended play  
DVD.  
• High-definition optical discs such as WMVHD,  
HD-DVD and Blu-ray  
• Progressive Scan component video ouputs  
(NTSC and PAL)  
• CD-R  
• CD-RW  
• VCD  
• Playback of JPEG image files  
Upgradeability via Internet  
High quality digital audio  
The ”firmware” controlling the functionality of  
the Harman Kardon DVD is fully upgradeable. In  
the event of future improvements to its  
operations and features, it will be possible to  
download firmware upgrades from  
All you have to do is create a CD-R with the  
data and insert it in the DVD for an automatic  
upgrade.  
• WMA (v8)  
• Built-in DVD-Audio decoder for improved  
musical realism.  
NOTE: Due to differences in the format of  
certain discs, it is possible that some discs may  
include a mix of features that are not compatible  
with the DVD. Similarly, although the DVD is  
capable of a wide range of features, not all discs  
include every capability of the DVD system. For  
example, although the DVD is compatible with  
multi-angle discs, that feature is only possible  
when the disc is specially encoded for multi-  
pleangle play. In addition, the DVD is capable of  
playing back both Dolby Digital and DTS sound-  
tracks, but the number and types of tracks  
available will vary from disc to disc. To make  
certain that a specific feature or soundtrack  
option is available, please check the options  
noted on the disc jacket.  
• By connecting a DTS (Digital Theater Systems)  
or a Dolby Digital decoder, you can enjoy high  
quality 5.1 digital surround sound from DTS or  
Dolby Digital discs.  
• With linear PCM audio at 16-24 bits and  
44-96 kHz (also on digital output, see table  
page 14), audio quality exceeding that of CD  
becomes possible.  
Packing List  
1 Harman Kardon DVD Player  
1 A/V cable for stereo analog audio and  
composite video  
• Optical and coaxial digital audio output.  
Many convenient features  
1 S-Video cable  
1 HDMI cable  
• On-Screen Menu lcons for disc information or  
player information and access to many major  
functions of this unit.  
1 owner's manual  
Playback capability for CD-R, CD-RW, WMA,  
JPEG, MP3, DivX, VCD/SVCD, DVD-R, DVD+R,  
DVD-RW and DVD+RW discs may vary due to  
variations in the quality of the disc and the  
recorder used to create the disc.  
• Subtitles may be displayed in one of numerous  
languages*.  
• The multi-angle function allows you to choose  
the viewing angle of scenes which were shot  
from a number of different angles (Limited to  
DVD’s recorded with multiple camera angles.)  
The DVD 28 is compatible with most discs  
recorded with files encoded using MP3 or  
Windows Media 8, as well as JPEG still  
images. However, note that variations in the  
encoder or codec used and the bit rate of the  
encoding may affect the DVD 28’s ability to  
play back a specific disc. As a result, we can-  
not guarantee complete compatibility with all  
encoders and versions of the codecs. For best  
results, we recommend that MP3 files be  
encoded at bit rates ranging between 32kbps  
and 320kbps. WMA files should be encoded  
at bit rates between 64kbps and 320kbps.  
Although the DVD 28 is capable of playing  
some WMA 9 files, not all features of version  
9 are supported. JPEG files should contain no  
more than 5 megapixels, and the file size  
should be no larger than 5Mb.  
• Multiple options for dialog language and  
soundtrack selection (limited to DVD’s  
recorded with multiple dialog languages or  
soundtracks).  
• Intuitive menu operating system.  
• 4 step Zoom during play and pause.  
• Backlit, ergonomically designed remote  
control.  
• Future software upgrades accessible via  
Internet. (See information below.)  
* The number of languages recorded depends  
on the software.  
FEATURES 27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Front Panel Controls  
DVD 28  
Open/Close  
AUDIO/VIDEO  
2
0
1
3
4
5
6
7
8
0
1
2
Main Information Display  
Power On/Off (Standby)  
Open/Close  
3
Play  
Pause  
Stop  
6
Skip/Search (Previous)  
Skip/Search (Next)  
Dimmer  
4
5
7
8
0
Main Information Display: This display  
4
Pause: Press this button to momentarily  
6
Skip/Search (Previous): Press this button  
delivers messages and status indications to help  
you operate the DVD player.  
pause playback. To resume playback, press the  
button again. If a DVD is playing, action will  
freeze and a still picture will be displayed when  
the button is pressed.  
to move backward through the music tracks on  
a CD disc or the chapters on a DVD disc. Keep  
the button pressed to search backwards at one  
of the available speeds.  
1
Power On/Off (Standby): Press the button  
once to turn the DVD player on, press it again to  
put the unit in the Standby mode.  
5
Stop: Press this button once to place the  
7
Skip/Search (Next): Press to move forward  
disc in the Resume mode, which means that  
playback will stop, but as long as the tray is not  
opened or the disc changed, DVD playback will  
continue from the same point on the disc when  
the Play Button is pressed again. Resume will  
also work if the unit was turned off. To stop a  
disc and have play start from the beginning,  
press the button twice.  
through the music tracks on a CD or the  
chapters on a DVD disc. Keep the button pressed  
to search forwards at one of the available  
speeds.  
2
Open/Close: Press this button to open or  
close the Disc Tray.  
3
Play: Press to initiate playback or to resume  
playback after Pause has been pressed.  
8
Dimmer: Press this button to reduce the  
brightness of the Information Display by 50% or  
to turn the display off completely in the  
following order: FULL BRIGHTNESS HALF  
BRIGHTNESS OFF FULL BRIGHTNESS.  
28 FRONT PANEL CONTROLS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Front Panel Information Display  
O
C
N
L
M J KI H G  
A
E
F
B
D
A Disc Type Indicators  
B Playback-Mode Indicators  
C Audio Bitstream Indicators  
F Title Indicators  
G V-OFF Indicator  
H Repeat Indicators  
K A-B Repeat Indicator  
L Program Indicator  
M Angle Indicator  
D Chapter/Track Number Indicators  
E Time Indicators  
I VCD Playback Control Indicator  
J Random Indicator  
N Parental Lock Indicator  
O Video Output Indicators  
A Disc Type Indicators: The CD, DVD, DVD-  
Audio, VCD, MP3, WMA or JPEG indicator will  
illuminate to show the type of disc currently  
being played.  
E Time Indicators: These positions in the  
indicator will show the running time of a DVD in  
play. When a CD is playing, these indicators will  
show the current track time, time remaining in  
the current track, or the total remaining time on  
the disc.  
I VCD Playback Control Indicator: This  
indicator lights when the playback control  
function is turned on with VCDs.  
J Random Indicator: This indicator lights  
when the unit is in the Random Play mode.  
B Playback-Mode Indicators: These  
indicators light to show the current playback  
mode:  
K A-B Repeat Indicator: This indicator lights  
when a specific passage for repeat playback has  
been selected.  
NOTE: The Indicators DEF will also display  
text messages about the DVD’s status, including  
LOADINGwhen a disc is loading,  
POWEROFFwhen the unit is turned off, and  
DISCERRORwhen a disc not compatible  
with the DVD is put into the play position.  
B
Lights when a disc is playing in the normal  
mode  
L Program Indicator: This indicator lights  
when the programming functions are in use.  
H
Lights when the disc is in the Fast Search  
Forward mode. The on-screen banner display  
indicates the selected speed (x2, x4, x8, x20,  
x100).  
M Angle Indicator: This indicator blinks when  
alternative viewing angles are available on the  
DVD currently playing.  
F Title Indicators: These two positions in the  
display will show the current title number when  
a DVD disc is playing.  
1
Lights when the disc is paused.  
N Parental Lock Indicator: This indicator  
lights when the parental-lock system is engaged  
in order to prevent anyone from changing the  
rating level without a code.  
G
Lights when the disc is in the Fast Search  
G V-OFF Indicator: This indicator lights when  
the unit's video output has been turned off by  
pressing the V-OFF button on the remote  
control.  
Reverse mode. The on-screen banner display  
indicates the selected speed (x2, x4, x8, x20,  
x100).  
O Video Output Indicators: When the  
C Audio Bitstream Indicators: When a  
Dolby® Digital, DTS® or linear PCM digital audio  
signal is present on the disc, one of these  
indicators will light. DVD-Audio, MP3 and WMA  
bitstreams will be indicated by the Disc Type  
Indicator A.  
DVD 28 is connected to a video display using  
H Repeat Indicators: These indicators light  
when any of the Repeat functions are in use.  
the HDMI Output  
A, the display sends infor-  
mation to the DVD 28 indicating the highest  
video resolution it is capable of handling, and  
the DVD 28 automatically sets the video output  
to match it. That resolution is displayed here.  
You may use the HD Mode Selector  
manually select a lower video output resolution.  
W
to  
D Chapter/Track Number Indicators: When  
a DVD disc is playing, these two positions in the  
display will show the current chapter. When a  
CD disc is playing they will show the current  
track number.  
FRONT PANEL INFORMATION DISPLAY 29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rear Panel Connections  
7
9
2
A
1
3
6
5
B
8
4
0
0
1
2
3
Optical Digital Output  
Coaxial Digital Output  
AC Power Cord  
4
5
6
7
S-Video Output  
Component Video Outputs  
Scart TV Output  
8
9
A
B
Remote Control Input  
Analog Audio Output  
HDMI Output  
Composite Video Output  
Remote Control Output  
6-Channel Audio Outputs  
0
Optical Digital Output: Connect this jack  
”Progressive” must be selected in the Video Set-  
up Menu in order to take advantage of the  
progressive scan circuitry. See page 19 for more  
information on progressive scan video.  
If your video display has a DVI input, you may  
use an optional HDMI-to-DVI cable or adapter  
for the connection to the display. In all cases, the  
video display must be HDCP-compliant in order  
to use the HDMI output. For best results, we do  
not recommend HDMI connections in excess of  
ten feet.  
to the optical digital input of an A/V receiver or  
surround processor for Dolby Digital, DTS or  
PCM audio playback.  
1
Coaxial Digital Output: Connect this jack  
IMPORTANT: These jacks should NOT be  
connected to standard composite video inputs.  
to the coaxial digital input of an A/V receiver or  
surround processor for Dolby Digital, DTS or  
PCM audio playback.  
6
SCART OUT (TV): If your TV has a SCART  
The following audio formats may be output via  
the HDMI connection:  
socket, you can connect a SCART cable to your  
TV and to your DVD Player for improved video  
quality. The SCART cable carries both audio and  
video. You can select Composite Video or RGB  
video for that SCART connector’s video output  
signal.  
NOTE: The coaxial digital output should only be  
connected to a digital input. Even though it is  
the same RCA-type connector as standard  
analog audio connections, DO NOT connect it to  
a conventional analog input jack.  
Audio CD – 2-Channel PCM or 5.1-channel DTS  
DVD-Audio – 2-Channel PCM  
DVD-Video – Up to 5.1-channel Dolby Digital or  
DTS  
Connect either the Optical Digital Audio  
Output  
Output  
7
Remote Control Output: Connect this  
Note: To hear the high-resolution surround  
sound recorded on DVD-Audio discs, you need  
0
or the Coaxial Digital Audio  
jack to the infrared (IR) input jack of another  
compatible Harman Kardon remote controlled  
product to have the built-in Remote Sensor on  
the DVD provide IR signals to other compatible  
products.  
1
to a corresponding digital audio  
to connect the 6-Channel Audio Outputs  
B
input on your receiver or processor, but not both.  
to the corresponding input jacks on your receiver  
or processor. These formats are not output digi-  
tally.  
2
AC Power Cord: Connect this plug to an  
AC outlet. If the outlet is controlled by a switch,  
make certain that it is in the ON position.  
8
Remote Control Input: Connect the  
B
6-Channel Audio Outputs: Connect these  
output of a remote infrared sensor, or the  
remote control output of another compatible  
Harman Kardon product, to this jack. This will  
enable the remote control to operate even when  
the front panel Remote Sensor on the DVD is  
blocked. This jack may also be used with  
compatible IR remote control-based automation  
systems.  
3
Composite Video Output: Connect this  
outputs to the matching 6-channel analog audio  
inputs on your receiver or surround sound  
processor. This connection is required to listen to  
the multichannel tracks on DVD-Audio discs. If  
the disc also contains a linear PCM, Dolby  
Digital or DTS track, you may listen to it using  
jack to the video input on a television or video  
projector, or to a video input on an A/V receiver  
or processor if you are using that type of device  
for video input switching.  
4
S-Video Output: Connect this jack to the  
S-Video input on a television or video projector,  
or to an S-Video input on an A/V receiver or  
processor if you are using that type of device for  
S-Video input switching.  
the HDMI  
Audio Output  
Outputs  
A
, Optical  
0
or Coaxial Dgital  
1
or the Analog Audio  
9
Analog Audio Output: Connect these  
9
.
jacks to an audio input on an A/V receiver or  
surround processor for analog audio playback.  
Note: You’ll find more details about all  
Audio/Video connections under Setup and  
Connections on the following pages.  
5
Component Video Outputs: These out-  
A
HDMI Output: If you have an HDMI-com-  
puts carry the component video signals for  
connection to display monitors with component  
video inputs. For standard analog TV's or  
patible receiver or video display device, connect  
this output to an HDMI input on the receiver or  
video display for the highest-quality uncom-  
pressed digital audio and video available. Even if  
your receiver is not capable of processing audio  
in the HDMI format, you may still experience the  
superb reproduction of HDMI video.  
projectors with inputs marked Y/Pr/Pb or  
Y/Cr/Cb, connect these outputs to the correspon-  
ding inputs. If you have a high-definition televi-  
sion or projector that is compatible with high  
scan rate progressive video, connect these jacks  
to the “HD Component” inputs. Note that if you  
are using a progressive scan display device, then  
30 REAR PANEL CONNECTIONS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup and Connections  
Before connecting your DVD 28, please:  
Ensure that the power switch of this unit and  
other equipment to be connected is set to off  
before commencing connection.  
Do not block ventilation holes of any of the  
equipment and arrange them so that air can  
circulate freely.  
Ensure that you observe the color coding  
when connecting audio and video cables.  
Read through the instructions before  
connecting other equipment.  
For the best quality, if your receiver or processor  
and/or video display are HDMI-capable, we rec-  
ommend using the HDMI output. With a single  
cable connection between components, HDMI is  
able to deliver uncompressed high-definition  
digital video and digital audio programming.  
rates the color (C) and luminance (Y) signals  
before transmitting them to the TV set in order  
to achieve a sharper picture. Use the S-video  
cable when connecting the player to a TV  
equipped with an S-video inputfor improved  
picture clarity. Never connect both outputs,  
Video and S-Video, to your TV or AV Receiver,  
only one of them.  
sion. It is recommended that you connect one  
of the video outputs from the DVD 28 to the  
corresponding input on your receiver to  
simplify operation of your home entertainment  
system. Refer to the owner’s guide for your  
receiver for more information.  
Note: If your video display has a DVI input, you  
may use an optional HDMI-to-DVI cable or  
adapter for the connection to the display. In all  
cases, the video display must be HDCP-compli-  
ant in order to use the HDMI output.  
• If your receiver is capable of multiroom opera-  
tion, it is recommended that you connect both  
the component (or HDMI) and composite  
video outputs of the DVD 28 to the receiver.  
This enables the highest-quality picture (com-  
ponent video) for viewing in the main listening  
room, while enabling the multiroom system, if  
it is video-capable, to distribute the composite  
video signal to the remote zone. Consult the  
owner’s guide for your receiver to determine  
whether it has video multiroom capability.  
Most European TV´s are equipped with SCART  
connectors rather than with a normal video  
input (yellow cinch). In that case the SCART  
connection should be used, providing the audio  
signal too. Separate analog audio connections to  
TV are needed only if your TV is connected to  
the video or S-video output.  
If your equipment is not HDMI-ready, we  
recommend the use of component video for  
higher quality pictures.  
If you are using a television or video display that  
is compatible with high-resolution 576P video  
signals, make sure to use the input jacks on the  
video display marked “HD Component,” if avail-  
able. Also, make sure to configure the display’s  
input settings for use with “576P” video signals.  
You will also need to change the scan type in  
the DVD 28’s Video Setup menu from  
You may also use the standard S-video or  
composite video connection if your TV does not  
have component video inputs. The component  
and S-video outputs are not available  
simultaneously.  
Connecting to a TV Only  
When using the DVD 28 with a television but no  
audio receiver or processor, connect it as follows.  
Make the Analog Audio Connection A and  
one of the Video Connections (Composite  
Video B, S-Video C, Component Video  
D). If your television or video display is HDMI-  
capable, you only need to make the HDMI E  
connection, as it handles both audio and video.  
Remember to plug in the power cord.  
• Modern audio/video receivers are capable of  
connection to several video source devices,  
such as the DVD 28 and a VCR, cable  
television set-top box, HDTV tuner or other  
device. The receiver is equipped with video  
monitor outputs for connection to your televi-  
sion, projector or plasma display. As you select  
any input source device, the receiver selects  
the correct video input and routes it to the  
correct video monitor output to your televi-  
“Interlaced” to “Progressive.” See above.  
The Video output (yellow) combines the com-  
plete video signal (composite) and sends it to  
the TV (or to the AV Receiver) by one line only.  
Use the Video output, when your TV set is  
equipped with a Video input jack only.  
The S (separate) video output connector sepa-  
TV  
To Y (green)/  
Pb (blue)/  
To video  
input  
To S-video  
Pr (red)  
connectors  
(yellow)  
on the TV  
To analog audio  
input connectors  
(red/white) on the TV  
input  
component  
video  
connectors  
To HDMI  
or DVI  
port on TV  
connectors  
on the TV  
To power outlet  
(AC 230V/50Hz)  
E
B
D
C
A
SETUP AND CONNECTIONS 31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup and Connections  
• When the audio signal is to be fed to an  
analog receiver rather than to the TV, connect  
Connecting to a Receiver/Amplifier  
With a Dolby Digital or DTS  
Decoder  
Connecting to a Receiver  
When using the DVD 28 with an audio/video  
receiver or processor, connect it as follows. First,  
make one of the video connections (Composite  
Video C, S-Video D, Component Video E  
or HDMI H) to the video input jacks on the A/V  
receiver, and then connect the receiver’s video  
monitor output to the TV. In addition, to benefit  
from the high-resolution surround sound formats  
recorded on DVD-Audio discs, which are not out-  
put via the HDMI connection, you will need to  
make the 6-Channel Audio Connection A to  
your receiver or processor.  
the Analog Audio Outputs  
9
to any analog  
audio inputs on your receiver or processor.  
One of the major advantages of the DVD format  
is its ability to use a variety of digital audio for-  
mats for the ultimate in sonic performance.  
However, in order to enjoy the benefits of digital  
audio, you must use a receiver or processor that  
has digital audio decoding capabilities and make  
an optical or coaxial digital audio connection  
between the DVD 28 and your home theater  
system. This simple connection is made as shown  
below with an optional coax or optical cable.  
Only one of these connections is required, and  
both should not be made at the same time.  
• The analog audio connection should also be  
made if you wish to play high-resolution 96kHz  
PCM audio discs where your receiver does not  
support 96kHz processing.  
NOTES ON VIDEO:  
Note: With multiple video sources, your  
Audio/Video device can be used for selecting  
the video signal and routing it to the TV.  
Connect the video or S-video output of the  
DVD player (whatever is provided with your  
device) to the video or S-video input on your  
device and the video/S-video output of this  
device to your TV. For more details, see the  
manual of your Audio/Video amplifier/receiver.  
Second, if your receiver or processor is not HDMI-  
capable, make either the Optical Digital Audio  
Connection G or the Coaxial Digital Audio  
Connection F, to the receiver or processor.  
In order to take advantage of the high-resolution  
DVD-Audio output of the DVD 28, you must  
connect the 6-Channel Audio Outputs  
B
to  
IMPORTANT NOTE: Make certain that any  
device being connected, including the DVD 28,  
your receiver or processor and your TV or video  
display, is turned off whenever you make connec-  
tions between products.  
the matching 6-channel inputs on your receiver  
or processor.  
Note for Analog Audio: The connection from  
Audio Out to the TV is optional only. Normally  
you´ll hear the sound from your AV-system´s  
speakers, so the TV volume should be com-  
pletely turned down. If you plan to use your  
DVD player also without having to turn on  
your complete system, this connection must  
exist, then you can turn up the TV´s volume as  
needed.  
NOTES FOR ANALOG AUDIO:  
• If you wish to use the DVD 28 as the input for  
a multiroom system, the Analog Audio  
Outputs  
9
should be connected to the  
standard analog left/right DVD or CD inputs on  
your digital receiver or processor.  
• The connection from the Analog Audio  
Outputs  
9
to the TV is optional.  
HDMI, DVI, Component,  
Front Speakers  
(Left/Right)  
Center  
Speaker  
Surround Speakers  
(Left/Right)  
Subwoofer  
S-video and/or  
Composite video  
monitor outputs  
TV  
Dolby Digital/DTS A/V Receiver or Processor  
To video  
input  
connectors  
(yellow)  
To Y (green)/  
Pb (blue)/  
Pr (red)  
component  
video  
To analog audio  
input connectors  
(red/white)  
on the TV  
or receiver  
To 6-channel  
analog audio  
inputs on  
To S-video  
input  
connectors  
To coaxial  
digital  
audio  
input  
connectors  
To  
HDMI  
or DVI  
port  
To optical  
digital  
audio  
input  
connectors  
receiver  
To power outlet  
(AC 230V/50Hz)  
connectors  
(see above)  
H
G
F
E
D
C
B
A
Important Notes on SCART and RGB  
format:  
Your DVD is equipped with a SCART connec-  
To view RGB video on your TV, the RGB  
compatible SCART connector on the TV must  
be used and the DVD´s TV SCART connector  
must be set to ”RGB”.  
Note that with RGB video the color intensity  
cannot be adjusted with most TVs.  
When the RGB video signal is used, DVD´s  
recorded with the NTSC format (with regional  
code 0 or 2) can be viewed even on non-  
NTSC compatible TVs.  
tor for direct connection to the TV.  
The SCART connector provides the video  
signal as well as audio (stereo L/R) signals.  
The SCART connector for the TV provides the  
composite video signal or the direct RGB  
signal, delivering the best video performance  
possible, selectable in the Setup menu.  
32 SETUP AND CONNECTIONS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Digital Audio Connections  
Audio output from the unit’s  
optical/coaxial digital audio  
output connector  
For your reference:  
Caution for the optical/coaxial  
digital audio outputs:  
Dolby Digital (AC-3) is a digital sound com-  
pression technique developed by the Dolby  
Laboratories Licensing Corporation,  
supporting 5.1-channel surround sound, as  
well as stereo (2-channel) sound, this  
When connecting an amplifier (with an  
optical/coaxial digital input ) which does not  
contain a Dolby Digital (AC-3) or DTS  
decoder, be sure to select ”PCM” as initial  
setting in the ”Digital Output” menu.  
Otherwise, any attempt to play a DVD may  
cause such a high level of noise that it may  
be harmful to your ears and damage your  
speakers.  
Gently push the cable plug through the built-in  
shutter that covers the optical digital audio out-  
put and connect the cable firmly so that the con-  
figurations of both the cable and the connector  
match.  
technique enables a large quantity of sound  
data to be efficiently recorded on a disc.  
Linear PCM is a signal recording format used  
in CDs. While CDs are recorded in  
44.1kHz/16 bit, DVDs are recorded in  
48kHz/16 bit up to 96kHz /24 bit.  
Disc  
Sound recording  
format  
Optical/coaxial digital  
audio output  
DVD  
Dolby Digital  
Dolby Digital bitstream  
(2-5.1ch) or PCM  
CD’s can be played as they would normally  
be played.  
If you have a Dolby Pro Logic Surround  
decoder connected to the DVD’s analog  
AUDIO OUT connectors, thanks to the  
”Downmix” function of the DVD you will  
obtain the full benefit of Pro Logic from the  
same DVD movies that provide full 5.1-chan-  
nel Dolby Digital soundtracks, as well as from  
titles encoded with Dolby Surround.  
(2ch, 48kHz, 16-bit)††  
Note:  
Linear PCM  
(48/96kHz,  
16/20/24-bit)  
Linear PCM (2ch)  
(48/96kHz,  
16/20/24-bit)  
Some first generation DTS decoders which do  
not support DVD-DTS interface may not work  
properly with the DVD/CD player.  
DTS  
Bitstream or no  
output*  
Dolby Digital, DTS and PCM signals are  
MPEG (2.0)  
MPEG  
passed through the HDMI Output  
A.  
bitstream (2ch)  
or linear PCM  
(2ch, 48kHz)  
However, DVD-Audio signals are not carried  
via the HDMI connection. You must connect  
The DVD is designed to digitally output  
96kHz-PCM audio with a 96kHz sampling  
rate. However, some 96kHz DVD's may  
include copy protection codes that do not  
permit digital output. For full 96kHz fidelity  
from these discs, use the analog outputs of  
the DVD.  
the 6-Channel Audio Outputs  
B
to the  
VCD  
CD  
MPEG-1  
CD-DA  
Linear PCM*  
corresponding input jacks on your receiver  
or processor in order to enjoy DVD-Audio  
materials.  
Linear PCM  
Linear PCM  
(44.1kHz sampling)  
Dolby Digital and DTS  
MP3  
MPEG-1  
Audio  
Linear PCM  
(44.1–48kHz,  
depending on  
source, if digital  
output format  
selected as  
Both Dolby Digital and DTS are audio formats  
used to record 5.1-channel audio signals onto  
the digital track of film. Both of these formats  
provide six separate channels: left, right, center,  
left rear, right rear, and common subwoofer.  
The latest 6.1-formats, Dolby Digital EX and  
DTS ES, even one (or two) additional "Surround  
Back" channel for a center between the rears.  
IMPORTANT: If your surround processor/D/A  
converter does not support 96kHz PCM audio,  
you must use the DVD analog outputs for full  
96kHz fidelity with these discs.  
Layer 3)  
“Bitstream”).  
(48kHz if digital  
output format  
selected as  
“PCM”)  
Linear PCM  
WMA  
Remember, that Dolby Digital or DTS will only  
play 5.1-channel sound if you’ve connected the  
optical or coaxial output of the DVD player to a  
DTS or Dolby Digital receiver or decoder and if  
the disc was recorded in the Dolby Digital or DTS  
format.  
(Windows  
Media  
Audio)  
(32–48kHz)  
* Digital Format must be selected as  
“ORIGINAL“ or ”PCM” respectively in Menu  
DVD-Audio  
The high-resolution output of DVD-Audio discs is  
only available as an analog signal. For that  
reason, it is necessary to make direct analog  
connections between the 6-Channel Audio  
Outputs  
B
on the DVD 28 and the matching  
6-channel inputs on your receiver or surround  
processor.  
DIGITAL AUDIO CONNECTIONS 33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playback Basics  
Slow Motion Playback (with DVD only)  
Basic Play  
Disc Playback Features  
1. When a DVD disc is in pause or freeze frame  
mode, you may move slowly forward or back-  
ward through the program being played at  
one of the speeds by pressing the Play  
Buttons on the remote. Each press of the  
buttons will move to the next speed, indicated  
by a number of arrow indicators on the right  
top of the screen.  
Preparation  
Skipping tracks or titles/chapters  
1. Switch the TV ON and select its video input  
connected to the DVD.  
To move forward or backward through the tracks  
on a CD or the titles or chapters on a DVD, press  
skip on the front panel or Previous/Next on the  
remote.  
2. Press POWER to turn on the unit, the DVD  
harman/kardon logo should appear now on  
the screen. If that logo appears distorted on  
the screen or without any color, change the  
appropriate settings at the Video Setting  
Submenu according to your TV set and to the  
connection used between the DVD and your TV.  
Fast Motion Playback/Fast Search  
1. To move forward or backward through the  
DVD or CD disc being played at fast speed,  
press SEARCH on the remote. Once one of  
these buttons is pressed, the fast search will  
continue until PLAY is pressed.  
2. Press PLAY to resume normal playback.  
Note that there will be no audio playback during  
slow-forward or -reverse play of DVD discs. This  
is normal for DVD, as A/V receivers and surround  
processors cannot process the digital audio  
streams during slow modes. Slow play is not  
available for CD.  
3. When you see no video at all, not even the  
harman/kardon logo, check the setting of the  
video input used on your TV (most SCART  
inputs on TVs can be configured in the TV´s  
menu). When you don´t succeed, connect your  
TV with different cables to the DVD, e.g. via  
Composite (yellow jacks) or S-Video cables,  
rather than per SCART to view the setup  
menus until all appropriate ”Video menu”  
settings are made properly.  
There are four fast-play speeds. Each press of  
the SEARCH Buttons will cycle to the next speed  
in the following order: x2, x4, x8, x20, x100,  
indicated by a number of arrow indicators on the  
right top of the screen.  
Notes: Playback features may not be available  
during the opening credits of a movie. This is  
intended by the disc author and is not a failure  
of the DVD.  
2. Press PLAY at any time to resume normal  
playback.  
Playback of a DVD with 96kHz/24-bit audio  
requires the use of circuitry normally used for  
other features. Accordingly, Slow Play Reverse  
and Step Advance features are not available  
with these discs.  
Note that there will be no audio playback during  
fast-forward or -reverse play of DVD discs. This is  
normal for DVD, as A/V receivers and surround  
processors cannot process the digital audio  
streams during fast-play modes; audio will be  
heard during fast-play of conventional CD’s.  
4. Switch on your A/V system’s power, if the  
player has been connected to such a system.  
5. Press OPEN/CLOSE to open the disc tray.  
6. Place a disc on the disc tray.  
Depending on the structure of a VCD disc, the  
functions Slow Reverse and Step Reverse may be  
prohibited or have no function and Fast Playback  
(Search) may not function.  
Hold the disc without touching either of its  
surfaces, position it with the side you wish to  
play facing down, align it with the guides, and  
place it in its proper position.  
Freeze Frame and Frame Advance  
(with DVD only)  
1. Press PAUSE when a DVD is playing to freeze  
the picture.  
3" (8 cm) discs or 5" (12 cm) discs can be  
used.  
2. Each time you press one of the STEP (FWD or  
REV) buttons, the picture advances one frame.  
7. Press PLAY. The disc tray is automatically  
closed and play begins.  
3. Press PLAY to resume normal playback.  
When the disc tray is closed by pressing  
OPEN/CLOSE, play will start automatically.  
With most DVD’s, a Disc Menu appears on the  
screen. Select specific menu item by using  
ARROW buttons on the remote, then press  
OK.  
34 PLAYBACK BASICS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playback Basics  
About DivX Movie Files  
Playing a DivX Movie Disc  
The DivX disc compatibility of this DVD player is  
limited by the following:  
Before playing DivX movie discs, please note the  
following:  
• the available resolution size of the DivX file  
should be below 720x576 (W x H) pixels.  
• multi session DVD containing Windows Media  
Audio files may not be supported.  
• the total number of files and folders on the  
disc should be less than 999.  
• open session discs are not supported.  
• the DVD player does not support PC data.  
• the number of screen frames per second  
should be below 29.97 frames per second.  
• this DVD player does not support an  
unfinalized disc with a closed session.  
• the video and audio structure of recorded file  
should be interleaved.  
1. Insert a disc and close the tray.  
2. Press the OSD button of the remote control  
and select a folder by pressing the up/down  
cursor buttons and press OK. A list of files in  
the folder appears. If you are in a file list and  
want to return to the Folder list, use the  
up/down buttons on the remote to highlight  
and press OK.  
The player is capable of playing DivX files with  
the extensions “.avi”.  
The player is capable of playing subtitle files  
with the extensions “.smi”, “.srt”, “.sub (Micro  
DVD format only)” or "ssa". Other subtitle files  
won’t be displayed. Subtitle files need to carry  
the same name as the movie file (but with either  
one of the above extensions) and should be  
located in the same directory.  
3. If you want to view a particular file, press the  
up/down buttons to highlight a file and press  
PLAY.  
When playing back a DivX movie you can use  
variable playback functions like fast and slow  
backward and forward, as well as step forward  
and step backward.  
4. Press STOP to stop the playback.  
The DVD player’s playback functionalities of DivX  
video discs will vary depending on the DivX  
version used for creating your movies.  
PLAYBACK BASICS 35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
System Setup  
NOTE: Before attempting to use the 13828  
system remote to control DVD 28, you must press  
Set Up Menu  
The first step in checking or changing the system  
defaults is to access the Setup Menu. First, make  
certain that the DVD is properly connected to a  
video display, and that power is connected. For  
this process, however, you do not need to load  
any discs into the unit.  
the DVD Button in the Input button group  
5.  
This activates the secondary functions for double-  
function buttons. Refer to the function list on  
page 7.  
System Defaults  
During STOP, PAUSE or PLAY mode, if you press  
SETUP on the remote, the Set Up Menu appears on  
the screen.  
The final step of the installation is to establish  
the system’s defaults. It is helpful to take a few  
minutes to familiarize yourself with these  
settings, as they may require change before the  
first use and later from time to time.  
This Main Menu and all menus in the following  
section may look different, listing the settings  
with different languages, depending on the set-  
tings made previously. With the factory default  
setting all languages are set to ”English”, that´s  
why with all menus the English version is shown  
in the manual.  
A Main Menu Line  
B Submenus  
General Functionality of the OSD Menu  
The complete setup and control of the DVD 28  
takes place in an advanced user-guided On  
Screen Display (OSD) menu system. The OSD can  
C Actual Settings  
D Instruction Line  
be activated by pressing the SETUP button  
9
on the remote control. Pressing this button again  
deactivates the OSD.  
In the SET-UP Menu you will find submenus for  
making or changing all settings and adjustments  
for both Audio and Video handling of your  
DVD 28.  
Most DVDs are created to allow setup menus to  
be displayed while the disc is playing, super-  
imposed over the video playback. However, some  
discs are authored in a way that does not allow  
The main menu consists of a PLAYER  
INFORMATION Menu and a SET-UP Menu. The  
PLAYER INFORMATION Menu will show all  
information and options available for the disc  
currently playing. The SET-UP Menu will help you  
configure all audio and video settings which are  
normally only made once.  
System Settings  
this. If you see the  
screen after pressing the Setup Button  
the Info Button , press the Stop Button  
and then press the Setup or Info Button  
69again.  
icon displayed on the  
9
or  
6
M
Each Main Menu contains Submenus. These sub-  
menus are shown as icons on the left side of the  
menu. They can be highlighted by a white square  
around the icon by moving the cursor with the  
ARROW buttons. Icons can be activated by  
pressing OK as soon as an icon is highlighted.  
When OK has been pressed, the color of the icon  
will change to dark blue and you will see that  
the Actual Settings of this submenu will appear  
on the right side of the menu.  
The System Setting Submenu contains the  
following settings. Follow the explanations in the  
Instruction Line on the bottom of your screen to  
change the settings.  
Although each Menu has various Submenus and  
Settings, navigating through menus, submenus  
and settings goes the same way. All submenus,  
settings and options can be accessed with the  
help of the ARROW (KLNM) and OK buttons  
on the remote control.  
Please note that when the menus prompt you to  
press ENTER, you must press the OK Button  
A
on the 13828 system remote.  
Display Language: Sets the language in which  
the OSD menus are shown on your screen.  
To change a setting, simply move the cursor to  
the setting you wish to change. This setting will  
be highlighted in light blue, and a brief explana-  
tion will appear in the Instruction Line on the  
bottom of your screen.  
Preferred Subtitle Language: Defines your  
preferred subtitle language. Every time a disc will  
be played that contains this subtitle language, it  
will be shown automatically. If you do not find  
your preferred language in the list of options, you  
can select your preferred language by highlight-  
ing OTHER. Press OK and use the Navigation  
Buttons to select your preferred language from  
the list shown on the screen. Note that only  
those languages will be available that are actual-  
ly on the DVD you would like to play. You can  
also set the preferred subtitle language to OFF. In  
that case no subtitles will be shown.  
Next, press the OK Button  
A
and a dropdown  
menu will appear that contains the available  
options for that setting. Press the KL  
Navigation Buttons  
option is highlighted, then press the OK Button  
to select that option.  
Z
until the desired  
A
36 SYSTEM SETUP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
System Setup  
Panel Time-Out: Sets the time-out interval for  
the Front Panel Information Display. After the  
selected time, the display will dim completely.  
PCM Limit: The DVD 28 is compatible with  
both 48kHz and 96kHz sampling, but some early  
A/V receivers and surround processors are not. If  
your A/V receiver or surround processor is NOT  
capable of handling 96 kHz signals, select the  
48kHz option. If your A/V receiver or surround  
processor IS capable of handling 96kHz signals,  
select the 96kHz option to achieve the greatest  
audio fidelity available. The AVR 138 is capable  
of handling 96kHz signals.  
Audio Settings  
Status Bar Time-Out: Sets the time-out  
interval for the Status Bar, after which the Status  
Bar will disappear from the screen.  
Parental Control: Defines a password used to  
control viewing of restricted programs. The  
default password is 1234. After pressing the  
default password, either the parental control  
setting can be chosen, or a new password. The  
five standard US rating symbols are ”G”  
(General, level 2), ”PG” (Parental Guidance,  
level 4), ”PG13” (Parental Guidance and 13  
years old, level 4), ”R” (Restricted, level 6) and  
”NC 17” (from 17 years old, level 7). The DVD  
will accommodate a total of eight rating steps,  
as set by the DVD creators. These additional  
steps allow for more critical control of program  
playback for all audiences. Level 8: All DVDs can  
be played. Levels 7 to 2: DVDs for general audi-  
ences/ children can be played. Level 1: DVDs for  
children can be played; DVDs for adults/general  
audiences are prohibited. Follow the explana-  
tions on the screen to set a new password.  
Note: Due to copyright restrictions, the DVD 28  
will not output an uncompressed signal in the  
PCM format from a disc recorded with  
The Audio Setting Submenu contains the  
following settings. Follow the explanations in the  
Instruction Line on the bottom of your screen to  
change the settings. In case the audio settings  
have been changed, they will take effect after  
the next time the player goes through STOP  
mode.  
96kHz/24-bit resolution, such as some DTS  
audio CDs. If the Digital Output setting in the  
AUDIOSETUPsubmenu is set to PCM, and  
the PCM Limit setting is set to 96KHZ, no  
audio will be outputted, and the message  
CGMSMUTEwill appear in the Main  
Information Display. “CGMS” stands for “Copy  
General Management System.” Should this  
message appear, change the PCM Limit setting  
to 48KHZto hear the audio at a lower  
resolution.  
Preferred Audio Language: Defines your  
preferred audio language. Every time a disc is  
played that contains this audio language, it will  
be activated automatically. If you do not find your  
preferred language in the list of options, you can  
select your preferred language by highlighting  
OTHER. Press OK and use the Navigation Buttons  
to select your preferred language from the list  
shown on the screen. Note that only those lan-  
guages will be available that are actually on the  
DVD you would like to play.  
Dynamic Range: This setting allows you to  
take advantage of the programming present on  
some Dolby Digital recordings to reduce the vol-  
ume of louder passages while maintaining intel-  
ligibility of quieter passages. This means that you  
may listen to programs at a level that allows the  
full impact of a soundtrack to be heard at a vol-  
ume that is lower than you might otherwise use  
to avoid disturbing others. The DVD 28 accom-  
plishes this by compressing the audio to a  
Disc Recognition: This setting controls the  
Disc Recognition feature. When turned on, it  
allows you to pause a DVD, remove it from the  
player, play another disc, and then resume  
playback of the original disc at a later time from  
the point at which you paused. Note that even  
when the setting is activated, you must pause  
playback, rather than bring it to a full stop, and  
the unit must not be turned off between discs.  
The DVD 28 is capable of storing the informa-  
tion for up to five DVDs at a time.  
Digital Output: If your system includes 5.1  
digital audio surround decoding (Dolby Digital  
and/or DTS), select BITSTREAM as the digital  
output. In that case all audio signals will be out-  
put with their original format. If your system only  
includes stereo and/or Dolby Pro Logic, select  
PCM. Then all audio signals will be output in  
PCM format only (DTS will output no signal).  
greater or lesser degree, depending on which  
setting you choose. Three options are available:  
MAXIMUMdoes not make any changes to  
the original playback, and should be used  
when the volume setting in the listening room  
may be as loud as you desire.  
PBC Support: Activates PBC (Play Back  
Control) Support for VCD discs.  
Screen Saver: Activates a Screen Saver to  
prevent an image to “burn” into a video display  
device. If you connect the DVD 28 to a LCD or  
plasma screen or video projector, we recommend  
you activate the screen saver at all times.  
MEDIUMapplies a moderate amount of  
compression so that louder passages are a  
little bit quieter.  
MINIMUMapplies more compression so  
that louder passages are much softer.  
Show Angle Icon: Determines whether the  
Angle Icon will appear on the screen when there  
are different angles available on a DVD disc.  
Feel free to experiment with the settings at any  
time. Note that if your receiver or processor also  
allows you to program the dynamic range  
setting, also known as the “Night Mode,” you  
do not need to make any adjustments on the  
DVD 28 and should leave the setting at  
MAXIMUM.  
Closed Caption: This setting enables viewing  
of closed caption messages, if they have been  
encoded in the video material. Closed captions  
are text displays of the program’s dialogue,  
normally hidden from view, that are made  
available for the hearing-impaired or others.  
Select the ONsetting to activate the DVD 28’s  
closed captioning decoder so that these  
messages may be viewed.  
SYSTEM SETUP 37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
System Setup  
While DVD-Audio also is output only in analog  
form, many discs also contain PCM, Dolby Digital  
or DTS digital tracks and may be played through  
Audio Adjustments Submenu  
This menu allows you to adjust bass manage-  
ment settings that control the audio output of  
the Digital Audio Outputs 01  
.
the 6-Channel Audio Outputs  
B
for speaker  
Delay Unit: This setting selects the unit of  
distance used for calculating delay times when  
the AUDIOADJUSTMENTSmenu is  
activated. The default unit is feet, but you may  
select meters.  
size, output level and delay times. The proper  
adjustment of these settings is key to optimal  
reproduction of DVD-Audio discs, when the  
DVD 28 is used with a receiver or processor that  
does not have audio adjustment capabilities for  
the direct inputs.  
Bass Management: This setting activates the  
AUDIOADJUSTMENTSmenu’s bass  
management settings, to optimize playback of  
DVD-Audio discs through the Analog Audio  
Outputs 9B. Three settings are available:  
The following adjustments are available on the  
AUDIOADJUSTMENTSmenu for each  
speaker position. It is recommended that you  
cycle through the adjustments for each speaker  
position using the KLM NNavigation  
Important Note: In order to avoid audio  
problems, when the DVD 28 is connected to a  
receiver or processor that does have the  
capability to adjust bass management  
parameters for its multichannel inputs, you have  
the option to either use that capability or adjust  
the settings in the DVD 28. The preferred method  
of operation is to use the receiver for these  
adjustments. In that case, remember to set the  
Bass Managementsetting in the  
AUDIOSETUPmenu to Bypass. If you  
make the adjustments using the DVD 28's  
settings, it is important that the receiver's  
settings for the multichannel direct inputs be  
disabled, or set to “Large” for the speaker sizes  
and “0” for the level adjustments and delay  
times, unless these settings are also used for the  
receiver’s other source inputs, in which case they  
should be left the way you set them when you  
configured your receiver. If you have any  
questions about the capabilities of your receiver  
or processor, we recommend that you consult its  
owner’s manual or the manufacturer’s Web site  
for further information.  
On: This is the default setting. If your receiver  
or processor is equipped with “direct” 6-chan-  
nel inputs and the receiver is not capable of  
performing bass management on these inputs,  
then leave this setting on the DVD 28 at the  
default of ON, and proceed to the AUDIO  
ADJUSTMENTSmenu to program the  
bass management settings.  
Buttons  
appropriate for your system. Pressing the OK  
Button displays a dropdown menu with the  
selections available for that setting. Use the  
KLNavigation Buttons to highlight  
the appropriate setting, and then press the OK  
Button to select it.  
Z
to enter the settings that are  
A
Z
A
You will notice that the adjustments for speaker  
size and distance (used to calculate delay times)  
are set in tandem for the front left and right  
speaker pair, and for the surround left and right  
speaker pair. Changing the settings for either  
speaker in these pairs also affects that setting for  
the other speaker in that pair. For this reason, it  
is important to select the same brand and model  
for both speakers in each pair, and also to place  
them at about the same distance from the  
listening position.  
Bypass: If your receiver or processor is  
equipped with 6-channel inputs and is capable  
of adjusting the bass management settings  
(speaker size, output levels and delay times)  
for its 6-channel analog inputs, then  
Harman Kardon recommends that you change  
this setting to Bypass, and adjust the bass  
management settings on your receiver.  
Stereo: If your receiver or processor is not  
equipped with 6-channel inputs at all, then  
change this setting to Stereo, which will  
send a downmixed 2-channel signal to the  
Speaker Size: Speaker size is part of the bass  
management system which determines which  
frequencies are sent to the specific speaker  
position, and which are sent to the subwoofer.  
The designation of “size” does not refer to the  
speaker’s physical size, but rather to the lowest  
frequency a speaker can handle. For this purpose,  
“full-range” speakers are considered “large,”  
while those not capable of reproduction below  
100Hz are considered “small.” In general, if you  
are using a packaged speaker system with  
smaller satellite-type speakers and a subwoofer,  
you should select Smallfor all five speakers.  
Largeshould only be selected if you are  
certain that your speakers are capable of  
If your receiver or processor does not have  
6-channel analog inputs, make sure to select  
Stereofor the BassManagement  
setting in the AUDIOSETUPmenu. Then  
Analog Audio Outputs  
9, for use with any  
2-channel analog input on your receiver.  
You may then select an analog surround mode  
available on your receiver.  
connect the Analog Audio Outputs  
9
to any  
2-channel analog inputs on your receiver.  
Before proceeding with the DVD 28’s audio  
setup adjustments, we recommend that you first  
use the menu system in your receiver or proces-  
sor to ascertain the settings already established  
for “Speaker Size,” “Output Level” and “Delay  
Time,” which may be set as a distance. Write  
these settings down to refer to during the  
configuration process.  
handling extreme low-frequency sounds.  
At the subwoofer setting, you can select the fre-  
quency under which bass information is directed  
to the Subwoofer Output and above which  
the remaining signal is directed to all other  
speakers. When making these selections, choose  
the crossover frequency that is closest to the  
lower frequency limit of your "SMALL" speakers.  
This figure is normally printed in the owner’s  
manual or data sheet for the speakers; or consult  
the speaker’s manufacturer.  
Press the Setup Button  
Setup menu; then use the KLNavigation  
Buttons until the AUDIOADJUST-  
MENTSsubmenu is highlighted within a white  
outline box, and press the OK Button  
9
to activate the  
Z
A
.
38 SYSTEM SETUP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
System Setup  
Delay  
Aspect Ratio: This step selects the TV aspect  
ratio, conventional screen shape (4:3) or  
widescreen (16:9), according to your TV.  
Video Adjustment: The Video Adjustment  
Submenu contains access to the Test Screen. First  
adjust the video display device (TV) with the help  
of the Test Screen. After that the output settings  
of the player can be fine-tuned with the  
Brightness, Sharpness and Black Level settings. In  
order to change the settings, move the cursor to  
the “+“ or “-“ icon on the same line as the set-  
ting. Once one of the icons is highlighted, press-  
ing OK will increase or decrease the value of the  
setting, as will be shown in the bar behind the  
setting. To exit the Video Adjustment Menu,  
move the cursor to DONE, and press OK.  
Due the different distances between the listening  
position for the front channel speakers and the  
surround speakers, the amount of time it takes  
for sound to reach your ears from the front or  
surround speakers is different. You may  
compensate for this difference through the use of  
the delay settings to adjust the timing for the  
specific speaker placement and acoustic con-  
ditions in your listening room or home theater.  
Measure the distance from the listening position  
to each of the individual loudspeakers. Once  
done, select per loudspeaker the distance that is  
closest to the one measured.  
When the HDMI Output  
A
is used, the aspect  
ratio will automatically be set appropriately for  
the specific display. However, you may select an  
alternate view.  
Video Standard: Sets the output video format  
i.e. NTSC, PAL or SECAM, of the DVD player. If  
you have a multi standard TV, we recommend the  
AUTO setting for optimal picture quality.  
Video Output: Sets the video output type to  
S-Video, Component or SCART. Scart will be used  
for most TV’s. Component will be used for most  
LCD, Plasma and projectors.  
Output level adjustment  
Output level adjustment is a key part of the  
configuration process for any surround sound  
product. It is particularly important for DVD-  
Audio, as correct outputs will ensure that you  
hear sound tracks with the proper directionality  
and intensity.  
Scan Type: This setting allows you to select  
between progressive and interlaced scanning for  
the Component Video Outputs  
mize the image resolution for the type of video  
display in use. The output at the S-Video and  
Composite Video outputs will always be  
5
to maxi-  
4
3
NOTE: Listeners are often confused about the  
operation of the surround channels. While some  
assume that sound should always be coming  
from each speaker, most of the time there will be  
little or no sound in the surround channels. This is  
because they are only used when a movie direc-  
tor or sound mixer specifically places sound there  
to create ambiance, a special effect or to contin-  
ue action from the front of the room to the rear.  
When the output levels are properly set it is  
normal for surround speakers to operate only  
occasionally. Artificially increasing the volume to  
the rear speakers may destroy the illusion of an  
enveloping sound field that duplicates the way  
you hear sound in a movie theater or concert  
hall.  
standard-rate video that is compatible with any  
television set or video display. Two choices are  
available:  
DivX Subtitle: This setting selects the desired  
subtitle language for DivX movies.  
Progressive: Select this option if you have a  
video display that is compatible with input  
sources of 480P or greater. Displays labeled as  
“HDTV Ready,” including virtually all large-screen  
LCD and plasma displays, are compatible with  
progressive scan.  
Below the menu items you will find your personal  
DivX Video On Demand (VOD) code.  
This code allows you to rent and purchase videos  
using the DivX VOD service. For more infor-  
instructions and download the video onto a disc  
for playback on this unit. Note that all the  
downloaded videos from DivX VOD can only be  
played back on this unit.  
Interlaced: Select this option when you are  
using an older video display that has Y/Pr/Pb  
component inputs, but which is not capable of  
displaying high scan rate, or “HD” signals.  
Once the DivX icon is highlighted, press OK to  
access your personal DivX VOD code.  
NOTES:  
1. The Scan Type may only be changed when the  
Video Output setting has been set to  
Component.  
The default settings of the DVD player is 0dB for  
all channels. In case you feel adjustments are  
necessary in your setup, we advise you to copy  
the settings currently in use with 5.1 surround  
modes (for instance Dolby Prol Logic II) of your  
AV receiver to the DVD player.  
HDMI Settings: This setting displays the  
characteristics of the video output signal at the  
HDMI Output  
connected to a video display using the HDMI  
Output , the display sends information to the  
A. When the DVD 28 is  
2. If you have connected the DVD 28 to a video  
display that is not capable of displaying  
progressive scan video using the Component  
A
DVD 28 that indicates the highest video  
resolution it is capable of handling, and the  
DVD 28 automatically sets the video output to  
match it. That resolution is displayed here. You  
may use this setting to manually select a lower  
video output resolution. Changes made here  
remain active until the DVD 28 or the display is  
turned off. When either is turned off, and then on  
again, the DVD 28 will revert to the default  
setting transmitted by the display. Make sure  
your video display or other video switching  
equipment (such as an HDMI-capable receiver) is  
capable of handling the DVD 28’s HDMI output  
signal.  
(Y/Pr/Pb) Video Outputs  
3, and you have  
inadvertently changed the Video Output  
Setting to Component and the Scan Type  
setting to Progressive, you may reset the scan  
type to interlaced by pressing the  
Video Settings  
Progressive Scan/Interlaced Button  
F.  
The display will blink, indicating that the scan  
type has been reset to interlaced mode.  
Scart Output: Selects which kind of video  
output signals will be routed over the scart.  
RGB will be used for most TV’s and is therefore  
recommended.  
The Video Setting Submenu contains the  
following settings. Follow the explanations in the  
Instruction Line on the bottom of your screen to  
change the settings.  
SYSTEM SETUP 39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Test Screen  
Contrast adjustment:  
Sharpness Adjustment  
Test Screen  
1. Adjust the contrast on your TV until you see a  
bright white bar in the right low corner of the  
screen and a deep dark black bar at the left.  
The optimal contrast setting will depend from  
your preference and the surrounding light in  
the TV room.  
Contrary to intuition, the picture will appear  
sharper and clearer with the sharpness, or Edges,  
setting backed off from the maximum setting.  
Reduce the sharpness setting on your television,  
and the Edges setting on the DVD 28 video  
adjustments menu if necessary, to minimize the  
appearance of any white lines between the bars  
in the gray scale portion of the test screen.  
When you activate the Test Screen via the OSD  
you can activate a still image to test all settings  
and the video performance of your TV. With the  
vertical color bars you can test the following:  
proper color intensity setting on your TV,  
2. If the brightness of the white bar will no more  
increase while turning up the contrast or when  
the borders of the white ”harman/kardon” text  
letters on top will bloom (overlight) into the  
black areas, what drasticly will decrease the  
sharpness of the script, then the Contrast has  
been turned up too much. Reduce the contrast  
until these effects will disappear and the video  
still looks realistic.  
the proper color of each bar, showing if the  
proper video standard is turned on: the colors  
should be (left to right): black, white, yellow,  
cyan (turquoise), green, magenta (purple), red,  
blue, black.  
Convergence and Edge Focus  
The crosshatch pattern that surrounds the test  
screen may be used to evaluate edge focus and  
convergence in front- or rear-projection video  
displays. However, the controls used to adjust  
these parameters are often not user-accessible.  
In any event, these adjustments are extremely  
complex, and require proper training and  
experience to avoid worsening the situation.  
Therefore, it is recommended that if you are  
unable to improve the picture using the available  
controls, contact the video display manufacturer’s  
authorized service representative for assistance.  
proper color transition, seen as sharp  
separation of the bars, S-Video will be better  
than Video, RGB best of all.  
the performance of the color filter in your TV  
(with ”Video” signals), bar edges should show  
no vertical crawling dots. Here S-Video and  
RGB formats usually give no problems.  
3. If you are watching TV with a usual surround-  
ing daylight, adjust the Contrast so that a nor-  
mal video picture has about the same looking  
as the surroundings in your room. By that way  
the eye is relazed when watching the TV pic-  
ture. This contrast setting may be reduced  
when the surrounding light is dimmed, usually  
improving the sharpness of a video a lot  
thereby.  
With the grey scale and the black/white fields  
below the color bars the brightness and contrast  
of your screen can be adjusted optimally, see  
chapter ”TV Picture Adjustment” below.  
When all desired setup and configuration entries  
have been made, use the KLNavigation  
Buttons  
bottom of the Video Adjustments submenu. Press  
the OK Button to select it to return to the  
on-screen menu system. Then, press the Setup  
Button to remove the menu displays from  
Z
until “Done” is highlighted at the  
4. The grey scale in the middle line needs to have  
the same clear difference between each bar as  
before the contrast adjustment. If not, go back  
to the brightness adjustment and repeat step 3  
and then the contrast adjustments, making  
only minor adjustments each time for  
optimisation.  
A
Color Bars  
Grey Scale  
9
the screen. The unit will return to normal opera-  
tion and you are ready to enjoy the finest in DVD  
or CD playback!  
100%  
Black/White  
fields  
Color adjustment.  
1. When the Brightness and the Contrast are set  
optimally, turn up the color control to the level  
of your perference. Adjust to the level where  
the colors look strong but still natural, not  
overdone. If the color level is too high,  
depending from the TV used some of the bars  
will seem wider or the color intensity will not  
increase while the control is turned up. Then  
the color control must be reduced again. At the  
end you should test the color intensity also  
with a video, e.g. pictures of natural faces,  
flowers, fruit and vegetables and other well  
known natural articles of our life most usefull  
for an optimal setting of the color intensity.  
TV Picture Adjustment with  
Test Screen  
These adjustments may be done now, but you  
can also make them after setup has been  
finalized.  
Brightness adjustment:  
1. Turn down the color control on your TV until  
the color bars are visible in black and white.  
2. Adjust the contrast to the lowest level where  
you still can see all bars within the grey scale  
in the test picture separately and clearly.  
3. Adjust the Brightness so that the bars in the  
grey scale are all visible. The bar furtherst to  
the left has to be as black as possible rather  
than grey but the next aside must clearly be  
differable. All the bars in the grey scale have to  
be gradually and evenly changing from black  
to whiter, going from left to right.  
2. If your TV has a Tint option (with most  
European TVs this is available or effective only  
with NTSC signals, not with PAL), use the large  
white bar below the Greyscale to tweak the  
warmth of the picture. Every viewer has a  
difference in preference as how the glow of  
the picture should be. Some prefer a little  
colder picture, some a warmer glow. The Tint  
function on your TV and the white bar can be  
used to control this. Adjust the Tint to the level  
where you feel the white color has the tone  
you prefer.  
40 TEST SCREEN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Player Menu  
Disc: This line displays the disc type.  
Using the Player Information Menu  
Using the On-Screen Status  
Display  
Disc ID: If the disc is encoded with an  
identification label, it will appear here.  
The DVD 28’s Player Information menu displays  
disc information and enables you to program  
When a DVD is playing, you may press the  
playback modes. Press the Info Button  
display the Player Information menu.  
6
to  
Status Button  
B
at any time to view a quick  
Aspect Ratio: This line displays the aspect  
ratio of the video content on the disc, and the  
format in which it is being played back  
according to the setting established in the  
VIDEOSETUPsubmenu as shown on  
page 39. Some discs may contain two versions  
of the same program with a widescreen  
aspect ratio on one side of the disc, and a  
standard aspect ratio on the other.  
summary of the disc’s playback status. The Status  
Bar not only gives you a snapshot of the unit’s  
current state; it also provides an easy way to  
select a different title, chapter or track, or use the  
time search feature.  
Video Standard: The disc’s format is shown  
here. For Region 2 players, this will normally  
be PAL, although some DVDs that are open  
region (playable in all regions) may be in the  
NTSC format.  
Title: This displays the current title on the  
left, and the total number of titles on the disc  
on the right.  
The Player Information menu has two submenus  
which may be accessed by using the KL  
Chapter: This displays the current chapter on  
the left, and the total number of chapters on  
the disc on the right.  
Navigation Buttons  
Z
to highlight the sub-  
Scan Type: This line displays whether the  
video program on the DVD was recorded with  
a progressive or interlaced scan rate. It also  
displays how the program is being played  
back, based on the setting established in the  
VIDEOSETUPsubmenu as shown on  
page 39.  
menu’s icon, and pressing the OK Button  
A
Play Mode Icon: This displays the current  
to select it. These submenus are different from  
the Setup menus in that many items are for dis-  
play only and cannot be changed using the menu  
system.  
play mode icon: e.g. Play  
Stop  
B, Pause  
1,  
0.  
Time Display: This section of the display  
shows the time corresponding to the type of  
display indicated in the Time Display Type.  
The Time Search function enables you to start  
playback at any point in the program. Use the  
PLAYBACKINFOSubmenu: This submenu  
displays basic disc and playback mode informa-  
tion. You may not make any changes to the items  
shown in this submenu, except for the Repeat  
mode.  
Audio Resolution: This line displays the  
sample rate and bit rate for the current audio  
format.  
M NNavigation Buttons  
Z
to highlight  
Audio Format: This line displays the current  
audio track, such as Dolby Digital 5.1 or linear  
PCM.  
this display, and the numbers will change to  
dashes. You may then use the Numeric Keys  
to enter the numbers corresponding to the  
time on the disc at which you wish play to  
Disc: This line displays the disc type, such as  
DVD-Video.  
Disc ID: If the disc is encoded with an identifi-  
cation label, such as a movie title, it will  
appear here.  
Video Bit Rate: This line displays the video  
bit rate up to the limit of 10 Mbps. This indica-  
tion will vary as a disc is played in response to  
changes in the amount of compression that  
was applied to the video signal when the disc  
was created. Thus, when the disc is stopped or  
paused, this line will remain blank.  
commence. Press the OK Button  
A, and  
play will immediately begin at the selected  
time position.  
Playlist: For DVDs, this line will reflect that  
playback will occur in the disc’s order.  
Programmable playlists are not available when  
a DVD is loaded.  
Time Bar: This display is a graphic representa-  
tion of the time elapsed for the title being  
played. As the disc plays, the number of bars  
will increase to reflect approximately what  
percentage of the title has been played thus  
far.  
When you have finished viewing the Player  
Repeat: This line displays the current repeat  
mode, or Off if Repeat mode is not active.  
menus, press the Info Button  
6
to remove  
the displays from the screen and return to normal  
play.  
Time Display Type: This section identifies the  
type of information in the Time Display  
section of the display. Use the KLM N  
Navigation Buttons  
setting, and each subsequent press of the OK  
Button will change the time display from  
Z
to select this  
A
Title Elapsed, to Title Remaining, to Chapter  
Elapsed to Chapter Remaining, and cycle back  
to Title Elapsed. The time displayed on screen  
and in the front-panel Information Display  
PROGRAMsubmenu: The PROGRAMsub-  
menu is not accessible for DVDs.  
0
will change accordingly.  
DISCINFOSubmenu: This submenu dis-  
plays detailed information about the disc content.  
You will not be able to make any changes to the  
items on this submenu. However, you may use  
the SETUPmenu system as described on page  
39 to change the DVD 28 player settings for  
video aspect ratio or scan type.  
PLAYER MENU 41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD Playback  
Many functions of the DVD 28 operate the same  
way for CD playback as for DVD play; however,  
there are some important differences. When a CD  
is loaded, the DVD 28 will automatically display  
the Player Information menu. Status banners are  
not available during CD play.  
Track List: A list of tracks on the disc will  
appear. Use the KLNavigation Buttons  
Z
to scroll through the list. Press the OK  
Button or the Play Button while a  
track is highlighted, to begin play.  
A
M
A greater variety of playback options are  
available during CD play, including Random play  
and programmed playlists.  
These and other features unique to CD play are  
described in this section.  
Disc InformationSubmenu: This  
screen displays abbreviated track and playback  
information, plus more detailed timing informa-  
tion. It is only available for CDs.  
Using the Player Information Menu  
The DVD 28’s Player Information menu displays  
disc information and enables you to program  
The information at the top of the screen provides  
the same information on the disc type, audio  
format, playlist setting, Repeat play setting and  
Random play setting as on the Playback  
Infosubmenu. The following additional  
information appears next.  
playback modes. Press the Info Button  
display the Player Information menu.  
6
to  
PROGRAMSubmenu: This submenu lets you  
program a playlist. The PROGRAMsubmenu is  
only accessible for CDs.  
Disc: This line displays the disc type.  
Audio: This line displays the type of audio  
recorded on the disc, usually Stereo.  
Track: This line displays the current track on  
the left, and the total number of tracks on the  
disc to the right.  
Playlist: With this line highlighted, press the  
OK Button  
A
to change the order in which  
Play Mode Icon: This icon will appear to the  
right of the Track display and will indicate the  
current playback mode.  
the tracks are played from the order in which  
they appear on the disc (Disc’sorder)  
to a playlist order which you may program  
(Programmedorder). A list of pro-  
gram steps and the track programmed for  
each step will appear at the bottom of the  
screen. You may enter a track number using  
Time: This section consists of three lines:  
The Player Information Menu has three sub-  
menus which may be accessed by using the  
Track Elapsed: Displays the elapsed or  
remaining time of the current track.  
KLNavigation Buttons  
the submenu’s icon, and pressing the OK  
Button to select it. These submenus are  
different from the Setup menus in that many  
Z
to highlight  
Disc Elapsed: Displays the elapsed or  
remaining time of the disc.  
the Numeric Keys  
Navigation Button  
another track.  
Use the KLM NNavigation Button  
X
and then press the  
A
L
Z
to program  
items are for display only and cannot be changed  
using the menu system.  
Elapsed Time Bar: Displays in graphical  
form a temperature bar reflecting the per-  
centage of the disc that has been played.  
Z
to select the desired program steps. Note that  
you may not enter a track more than once in  
the playlist, if it appears in an earlier step.  
However, you may use the Repeat function  
while the playlist is playing. After you have  
finished programming the playlist, press the  
PLAYBACKINFOSubmenu: This submenu  
displays basic disc and playback mode information.  
Use the KLNavigation Buttons  
highlight either Track Elapsed or Disc Elapsed,  
and each press of the OK Button will tog-  
Z
to  
Disc: This line displays the disc type, such as  
CDDA (Compact Disc Digital Audio).  
A
gle between the elapsed and remaining settings.  
The time displayed to the right and in the front-  
Audio: This line displays the type of audio  
recorded on the disc, usually Stereo.  
Play Button  
3
M
to begin play.  
panel Information Display  
0
will change  
accordingly.  
Playlist: For CDs only, you may choose to  
play the tracks in order as they appear on the  
disc, or you may program a playlist containing  
some or all of the tracks in the order in which  
you wish to hear them. This line indicates  
which of these two modes has been selected.  
In order to change this setting, you will need  
to access the PROGRAMsubmenu as  
described below.  
The Time Search function enables you to start  
playback at any point in the program. Use the  
KLNavigation Buttons  
the time display. Press the Numeric Keys  
followed by the OK Button to select a new  
Z
to highlight  
X
A
point in the track from which to commence play.  
When you have finished viewing the Player  
menus, press the Info Button  
the displays from the screen and return to normal  
play.  
6
to remove  
Repeat: With this line highlighted, press the  
OK Button  
A
to activate Repeat mode.  
Each press will change the repeat mode from  
Repeat 1 (to repeat one track) to Repeat All  
(to repeat all tracks on the disc) to Repeat Off.  
Random: With this line highlighted, press the  
OK Button  
A
to activate Random mode.  
Each press will toggle between turning the  
Random play on or off.  
42 CD PLAYBACK  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD Playback  
Selecting a Track  
To select a track, make sure the Player  
Information menu is on screen. Press the Info  
A-B Repeat Play  
Video Off Feature  
The Repeat A-B function allows you to select any  
portion of a CD and have it repeat continually  
until the unit is manually stopped.  
During CD playback, some listeners may prefer to  
turn off the DVD 28’s video circuitry. Although  
the video section is electrically isolated from the  
audio section, some users may prefer to turn the  
video displays off during audio playback to  
prevent any possibility of interference between  
audio and video. You may also wish to turn the  
video display off if you find the menu system  
distracting or unnecessary during CD playback.  
Button  
press the KLM NNavigation Button  
so that the Track Number is highlighted. Use the  
Numeric Keys to enter the desired track,  
6
to activate it if necessary. Next,  
Z
To initiate a Repeat A-B playback sequence,  
follow these steps while a disc is playing:  
X
and press the OK Button  
the new track.  
A
to begin playing  
1. Press the A-B Repeat Button  
H
on the  
remote when you want to choose the begin-  
ning point; the Repeat icon appears in the  
upper right corner of the screen, followed by  
A-to indicate the beginning of the passage  
to be repeated.  
To select a specific track on a CD at any time  
during playback, simply press the number  
corresponding to the track you wish to listen to  
using the Numeric Keys  
move one by one through the chapters at any  
time by pressing the Skip DWN (Down)/  
Skip Up Buttons 67  
the DWN or Skip Reverse  
IMPORTANT NOTE: It is strongly recommended  
that plasma video display owners use the Video  
Off feature to avoid burn-in.  
X. You may also  
2. Press the A-B Repeat Button  
H
again to  
To turn the video displays off while a CD is  
playing, simply press the Video Off Button  
choose the end point. Repeat A-B has been  
set, and the A-B section will be played  
continuously.  
N
. When you press  
button once, the  
6
b
. Press the button again to restore the video  
player will return to the start of the current track.  
Additional presses of either button will step back  
through the available tracks, one at a time.  
output. The V-Off Indicator G will light to  
remind you that the video displays have been  
turned off. Note that the video output will  
automatically be restored each time the DVD 28  
is turned on.  
3. Press the A-B Repeat Button  
remote again to cancel Repeat A-B mode.  
H
on the  
Note: When a JPEG, MP3 or Windows Media  
disc is playing, a special screen will appear.  
Random Play  
The Random Play function will play all of the  
tracks on a CD in a random order, as selected by  
the DVD 28. Once the DVD 28 has played all of  
the tracks on the disc once, it will stop.  
Repeat Play  
The DVD 28 offers several repeat functions for  
CDs that allow you to take advantage of the  
capacity of the unit for unattended playback:  
You may select the random mode by pressing the  
Repeat Program: Repeats the current playlist  
if Programmed Order has been selected at the  
Playlist setting.  
Random Button  
S
on the remote. Each press  
will toggle the  
of the Random Button  
S
setting between “Off” and “On”, meaning that  
the remaining tracks on the disc will be played in  
random order.  
Repeat 1 Track: For CDs, VCDs, MP3s and  
WMAs, repeats the track or file currently being  
played until the disc is manually stopped. The  
Repeat and 1 indicators will light in the front-  
panel display, and the REPEAT1icon will  
appear on screen.  
The Random Indicator J in the Front-Panel  
Information Display  
Random setting is on.  
0
will light any time the  
Repeat Disc: For CDs, VCDs, MP3s, WMAs,  
and JPEGs, repeats the entire disc until play is  
manually stopped. The Repeat and All  
indicators will light in the front-panel display,  
and the REPEATALLicon will appear in  
the Status Bar.  
Repeat Folder: For MP3s, WMAs and JPEGs,  
repeats all tracks within the current folder until  
play is manually stopped. The Repeat H  
indicator will light in the front-panel display,  
and the REPEATFOLDERicon will  
appear on screen.  
Repeat A-B: Repeats any selected portion of  
the disc until the disc is manually stopped (see  
below for more information).  
To select any Repeat mode (other than Repeat A-B):  
While a disc is playing, press the Repeat  
Button  
R
on the remote. The Repeat icon will  
appear on screen, indicating the new repeat  
mode. Each press of the Repeat Button  
R
will cycle through the available repeat modes. To  
end Repeat play, continue pressing the Repeat  
Button  
R
until the Off mode is selected.  
CD PLAYBACK 43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MP3, Windows Media and JPEG Playback  
Discs containing MP3, WMA or JPEG files are  
• Press the Search Forward  
Reverse buttons, for fast search of a  
track. Press the Play , Pause or  
Stop Button to end fast play.  
7
M
or Search  
MP3, Windows Media and JPEG  
Playback  
navigated and controlled differently from  
standard DVDs and CDs. When a disc containing  
one or more of these types of files is loaded in  
the DVD 28, the Player Information menu screen  
will appear.  
6M  
3
M
M
4M  
The DVD 28 will recognize data from CD-ROM  
discs recorded in the MP3, Windows Media 8  
(WMA) or JPEG formats, including images stored  
on Kodak Picture CDs. You may also play discs  
with more than one of the three formats.  
5
• Slow-play is not available during MP3/WMA  
playback.  
• You may play an MP3 or WMA disc in random  
mode like a normal CD. You may also access  
the Random function while an MP3 or WMA  
disc is playing by pressing the Random  
The Specific File Types That May be Played  
on the DVD 28 Are:  
MP3 Files: MP3 is a popular audio compres-  
sion format that was developed by the Motion  
Picture Experts Group as part of the MPEG-1  
video compression format. Depending on the  
specific MP3 encoder used, file size is greatly  
reduced so that you store many more songs on  
one compact disc than in the standard audio  
CD format. MP3 is also used to download  
audio files to computers for home use. Note,  
however, that in order to play an MP3 file on  
the DVD 28, the disc may not contain any  
encryption or coding that prevents playback.  
Always be certain that you have, or have  
purchased, the proper rights or authorization  
before creating a CD-ROM with MP3 or any  
other codec format. Due to variations in the  
different encoders and variations of the MP3  
codec and the different bit rates used to record  
MP3 discs, the DVD 28 may not be able to play  
all discs with MP3 files. We cannot guarantee  
complete compatibility with MP3 discs, even  
though they may play on a computer. This is  
normal and does not indicate a problem with  
the DVD 28. Note, also, that when a multi-  
session disc with both standard CD audio and  
MP3 (or WMA) content is used, the DVD 28  
will only play the CD audio sections of the disc.  
Button  
S.  
• The Repeat function may be accessed during  
playback of an MP3 or WMA disc by pressing  
the Repeat Button  
R
on the remote.  
Repeatedly press the Repeat Button  
R
to  
scroll through the options of Repeat 1 (repeat  
one file), Repeat All (repeat all files) or Repeat  
Folder (repeat all files within the current  
folder). The next press will turn the repeat  
function off. Repeat A-B is not available during  
MP3/WMA playback.  
This screen will display a list of the main folders  
contained on the disc The elapsed time will  
appear in the upper right corner of the screen. It  
isn’t possible to change the time display, and the  
Time Search function is not available.  
MP3 or WMA Disc Playback  
NOTES ON MP3 AND WMA PLAYBACK  
• During playback, the front-panel display and  
the time indicator on the screen above the list  
will show the elapsed time of the track being  
played. Other time display options are not  
available with MP3/WMA playback.  
MP3 and WMA discs may contain 200 tracks or  
even more. To get the best overview about all  
tracks on the disc and their names and to select  
them comfortably, use the on-screen display  
rather than the front-panel display. The front-  
panel display will only show the number and the  
elapsed time of the track being played for WMA  
files.  
• The DVD 28 is only compatible with standard  
MP3- and WMA-encoded discs. Other  
compressed audio formats used for Internet  
audio downloads will not play on the DVD 28.  
The supported bit rate for WMA files is between  
64k bits and 320k bits. The supported bit rate for  
MP3 files is between 32k bits and 320k bits.  
• Due to the differences in various versions of  
the MP3 and WMA formats, and the many  
differences between the CD-R machines used  
to record discs on a computer, it is possible  
that some discs may not play on the DVD 28  
even though they will work on a computer. This  
is normal and does not indicate a fault with  
the unit.  
• To select a folder (if any), press the KL  
Navigation Buttons  
folder name is high-lighted, then press the OK  
Button  
Z
until the desired  
WMA Files: WMA (Windows Media Audio) is  
an audio compression format developed by the  
Microsoft® Corporation for use with its  
Windows Media Player. WMA files may be  
created with greater compression than MP3  
without sacrificing audio quality so that even  
more songs may be recorded on a disc. Note  
that there have been a number of versions of  
Windows Media, and the DVD 28 is compatible  
only with files that end in the “wma”  
A
.
• To select a track, press the KLNavigation  
Buttons until the desired track name is  
highlighted. To start play of the track selected  
on the list, press the OK Button or Play  
Button  
Z
• When a multisession disc with both standard  
CD audio and MP3 or WMA content is in use,  
the DVD 28 will play only the CD audio sec-  
tions of the disc. Track numbers will be visible  
in the display, but the files will not be decoded.  
A
3
M.  
During MP3/WMA playback, some of the  
standard CD/DVD playback controls operate in  
their normal fashion:  
• If a disc containing MP3, WMA and/or JPEG  
files is created in more than one session, the  
DVD 28 may not recognize files added during  
the later sessions, especially if the disc was  
finalized after the first session.  
extension and that were recorded using the  
Windows Media Series 8 encoding.  
• You may skip forward to the next track on the  
disc by pressing the Skip/UP Button  
7N.  
JPEG Files: “JPEG” is the acronym used to  
identify image files recorded according to  
specifications established by Joint  
• You may skip back to the previous track on the  
disc by pressing the Skip/DWN Button  
6
N.  
Photographic Experts Group for compressing  
still images. Identified by the file extension  
“jpg” when they are recorded on most com-  
puters, JPEG files may be created by a digital  
still camera and then edited and “burned” to a  
disc in your personal computer, recorded on a  
CD-ROM disc from film images by a photo  
processor, or scanned from printed photos into  
your personal computer and then burned onto  
a CD-ROM.  
• Press the Pause Button  
momentarily stop playback. Press the Play  
Button  
Button  
4
M
to  
3
5
M
M
to resume play. Press the Stop  
to enter stop mode.  
44 MP3, WINDOWS MEDIA AND JPEG PLAYBACK  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MP3, Windows Media and JPEG Playback  
• When a disc with multiple folders is playing,  
only tracks from one folder can be displayed  
and played at a time. Select the desired folder  
You may view thumbnails of the images in the  
selected folder by pressing the Disc Menu  
Button . When the images appear on  
screen, you may use the KLMNNavigation  
Buttons to move the picture frame around  
until the desired image is selected. Press the OK  
a
and press the Play Button  
3
M
or  
OK Button to start the first track.  
A
Z
To see and play tracks from other folders, you  
must first select the root folder using the  
Button  
A
to display a full-size view of that  
KLNavigation Buttons  
Z
, and press  
image.  
the OK Button to open or close that fold-  
A
er. You may then navigate an open folder and  
select the desired folder. Press the OK Button  
A
to open the folder, and select the desired  
track. Then press the Play Button  
3
M.  
• Only stereo audio playback is available for MP3  
and WMA discs.  
• Programmed playlists are not available for  
MP3/ WMA discs.  
• Use the KLMNNavigation Buttons  
Z
to select the DISCINFOSubmenu icon on  
the left side of the screen, and press the OK  
Button  
A
to view it. If the disc contains ID3  
tag information, then the current MP3 track  
information will appear: song title, artist,  
album, year, genre, and any comments. For  
WMA and JPEG files, only the file name will  
appear.  
JPEG Playback  
The DVD 28 is capable of recognizing JPEG still-  
image files and displaying them. When a disc or  
folder containing JPEG files is loaded, the JPEG  
Disc-Type Indicator A will light in the Main  
Information Display  
0. The disc will  
immediately begin displaying the images on the  
disc in order.  
When viewing JPEG images, the Angle Button  
C
may be used to rotate the image. With the  
image on-screen, press the Angle Button  
C
once to display the current orientation of the  
image, usually +0. Press the Angle Button  
again within one second to rotate the image  
C
clockwise 90 degrees. The new orientation of  
+90 will be displayed. Each additional press of  
the Angle Button  
C
will continue to rotate  
the image clockwise by 90 degrees.  
You may use the Zoom Button  
a JPEG image, and the KLMNNavigation  
Buttons to explore the enlarged image.  
W
to enlarge  
Z
MP3, WINDOWS MEDIA AND JPEG PLAYBACK 45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting Guide  
TroubleShooting Guide  
Symptom  
Possible Cause  
Solution  
Unit does not turn on  
• No AC power  
• Check AC power plug and make certain any switched  
outlet is turned on.  
Disc does not play  
• Disc loaded improperly  
• Load disc label-side up; align the disc with the guides and place  
it in its proper position.  
• Incorrect disc type  
• Check to see that disc is CD, CD-R, CD-RW, DivX, VCD, MP3, WMA,  
JPEG, DVD-R, DVD-RW, DVD+R, DVD+RW (standard conforming),  
DVD-Audio or DVD-Video; other types will not play.  
• Invalid Region Code  
• Use Region 2 or Open Region (0) disc only.  
• Rating is above parental preset  
• Enter password to override or change rating settings.  
No picture  
• Intermittent connections  
• Wrong input  
• Check all video connections.  
• Check input selection of TV or receiver.  
• Progressive Scan output selected  
• Use Progressive Scan mode only with compatible TV. If needed, press  
the Progressive Scan/Interlaced Button  
F
to toggle to the  
correct mode.  
• Video Off feature active  
• Press Video Off Button  
b
to reactivate video circuitry (see page 43)  
HDMI Output  
A
is connected to a  
• The HDMI Output may not be used with video displays that are not  
A
video display that is not HDCP-compliant. HDCP-compliant. Unplug the cable and select another audio and video  
connection (see pages 31 through 32).  
No sound  
• Intermittent connections  
• Check all audio connections.  
• Incorrect digital audio selection  
• DVD disc is in fast or slow mode  
• Surround receiver not compatible  
with 96kHz PCM audio  
• Check digital audio settings.  
• There is no audio playback on DVD discs during fast or slow modes.  
• Use analog audio outputs.  
• DVD Audio disc is loaded without  
using analog audio connection  
• Use 6-Channel Audio Outputs  
B
or Analog Audio Outputs  
9.  
Picture is distorted or jumps during  
fast forward or reverse play  
• MPEG-2 decoding  
• It is a normal artifact of DVD playback for pictures to jump or show  
some distortion during rapid play.  
Some remote buttons do not operate  
during DVD play; prohibited symbol  
appears (see below)  
• Function not permitted at this time  
• With most discs, some functions are not permitted at certain  
times (e.g., Track Skip) or at all (e.g., direct audio track selection).  
The OSD menu is in a foreign language  
• Incorrect OSD language  
• Change the display language selection.  
The  
symbol appears  
• Requested function not available at  
this time  
• Certain functions may be disabled by the DVD itself during  
passages of a disc.  
Picture is displayed in the  
wrong aspect ratio  
• Incorrect match of aspect ratio settings • Change aspect ratio settings.  
to disc  
Remote control inoperative  
Disc will not copy to VCR  
Password not accepted.  
• Weak batteries  
• Sensor is blocked  
• Change both batteries.  
• Clear path to sensor or use optional outboard remote sensor.  
• Copy protection  
• Many DVDs are encoded with copy protection to prevent  
copying to VCR.  
• Incorrect password being used or  
password has been forgotten.  
• Stop play of disc. Press and hold the Clear Button  
blinks. This resets the password and all settings to their defaults.  
D
until the display  
46 TROUBLESHOOTING GUIDE  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Specifications for AVR 138  
Audio Section  
Stereo Mode  
FM Tuner Section  
Frequency Range  
87.5108MHz  
IHF 1.3 µV/13.2dBf  
Mono/Stereo: 70/65dB (DIN)  
Mono/Stereo: 0.15/0.3%  
35dB @ 1kHz  
400kHz: 70dB  
80dB  
90dB  
Continuous Average Power (FTC)  
Usable Sensitivity  
Signal-to-Noise Ratio  
Distortion  
Stereo Separation  
Selectivity  
40 Watts per channel, 20Hz–20kHz,  
@ < 0.07% THD, both channels driven into 8 ohms  
Five-Channel Surround Modes  
Power Per Individual Channel, all channels driven simultaneously  
Image Rejection  
IF Rejection  
Front L&R channels:  
30 Watts per channel,  
@ < 0.07% THD, 20Hz–20kHz into 8 ohms  
AM Tuner Section  
Frequency Range  
Signal-to-Noise Ratio  
Usable Sensitivity  
Distortion  
522–1620kHz  
45dB  
Loop: 500µV  
1kHz, 50% Mod: 0.8%  
10kHz: 30dB  
Center channel:  
30 Watts, @ < 0.07% THD, 20Hz–20kHz into 8 ohms  
Surround channels:  
30 Watts per channel,  
@ < 0.07% THD, 20Hz–20kHz into 8 ohms  
Selectivity  
Input Sensitivity/Impedance  
Video Section  
Video Format  
Linear (High Level)  
200mV/47kohms  
95dB  
PAL/NTSC  
Signal-to-Noise Ratio (IHF-A)  
Input Level/Impedance 1Vp-p/75 ohms  
Output Level/Impedance 1Vp-p/75 ohms  
Video Frequency  
Surround System Adjacent Channel Separation  
Analog Decoding  
(Pro Logic, etc.)  
Dolby Digital (AC-3)  
DTS  
40dB  
Response  
10Hz–8MHz (–3dB)  
55dB  
55dB  
General  
Power Requirement  
Power Consumption  
AC 230V/50Hz  
72W idle, 580W maximum  
(2 channels driven)  
Frequency Response  
@ 1W (+0dB, –3dB)  
10Hz100kHz  
25 Amps  
High Instantaneous  
Current Capability (HCC)  
Dimensions (Max)  
Width  
440mm  
165mm  
382mm  
9.6 kg  
Transient Intermodulation  
Distortion (TIM)  
Height  
Depth  
Weight  
Unmeasurable  
16 µsec  
Rise Time  
Slew Rate  
40V/µsec  
Depth measurement includes knobs, buttons and terminal connections.  
Height measurement includes feet and chassis.  
All features and specifications are subject to change without notice.  
Harman Kardon is a registered trademark.  
*Manufactured under license from Dolby Laboratories.  
“Dolby, Pro Logic, and the Double-D symbol are  
trademarks of Dolby Laboratories, Inc.  
Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380;  
5,978,762; 6,487,535; 7,003,467 & other U.S. and worldwide patents issued &  
pending. DTS, DTS Digital Surround, ES, and Neo:6 are registered trademarks and the  
DTS logos Symbol are trademarks of DTS, Inc. © 1996-2007 DTS, Inc. All Rights  
Reserved.  
Logic 7 is a registered trademark of Lexicon, Inc.  
TECHNICAL SPECIFICATIONS 47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Specifications for DVD 28  
Applicable Disc:  
Disc formats: 5 inch (12 cm) or 3 inch (8 cm) DVD Video, DVD-Audio, Standard conforming DVD+RW, DVD+R, DVD-R,  
DVD-RW, DivX, VCD, CD, CD-R, MP3, WMA, JPEG or CD-RW discs,  
Regio code: DVD Movie disc with Code 2 or 0 only.  
DVD-Layers: Single Side/Single Layer, Single Side/Dual Layer, Dual Side/Single Layer, Dual Side/Dual Layer  
Audio formats: DVD-Audio MLP lossless, Linear PCM, MPEG, Windows Media® 9,  
Dolby Digital or DTS Audio discs  
Still-image format: JPEG  
Video Signal System:  
HDMIOutput:  
PAL/NTSC  
Video: 576p, 720p, 1080i  
HDMI Version 1.0-compliant  
HDCP Version 1.1-compliant  
Composite Video Output:  
S Video Output:  
1 Vp-p/75 Ohms, sync negative polarity  
Y/Luminance: 1 Vp-p/75 Ohms, sync negative polarity  
C/Chrominance: 0.286 Vp-p  
Component Video Output:  
Y: 1 Vp-p/75 Ohms, sync negative polarity  
Cr: 0.7 Vp-p/75 Ohms  
Cb: 0.7 Vp-p/75 Ohms  
2 Vrms max  
Analog Audio Output:  
Frequency Response:  
DVD (Linear PCM):  
2Hz - 22kHz (48kHz sampling)  
2Hz - 44kHz (96kHz sampling)  
CD:  
2Hz - 20kHz  
Signal/Noise Ratio (SNR):  
Dynamic Range:  
105 dB (A-weighted)  
DVD: 100dB (18 Bit) / 105dB (20 Bit)  
CD/DVD: 96dB (16 Bit)  
THD/1kHz:  
DVD/CD: 0.0025 %  
Below Measurable Limits  
100 - 240 V/50 ~ 60 Hz  
1 Watts (Standby)/13 Watts (Max)  
440 x 50 x 285 mm  
4.0 kg  
Wow & Flutter:  
AC Power:  
Power Consumption:  
Dimensions (WxHxD):  
Weight:  
Depth measurement includes knobs and connectors.  
Height measurement includes feet and chassis.  
All specifications subject to change without notice.  
Harman Kardon and Harman International are registered trademarks of Harman International Industries, Incorporated.  
Manufactured under license from Dolby Laboratories. Dolby, Dolby Digital, ProLogic and the double-D symbol are trademarks of  
Dolby Laboratories.  
Manufactured under license under U.S. Patent #: 5,451,942 & other U.S. and worldwide patents issued & pending. DTS and DTS Digital Out are registered  
trademarks and the DTS logos and Symbol are trademarks of DTS, Inc. © 1996-2007 DTS, Inc. All Rights Reserved.  
Microsoft, Windows and WMA are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.  
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.  
DivX, DivX Certified, and associated logos are trademarks of DivX Networks, Inc and are used under license.  
This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights  
owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation and  
is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or diassembly is  
prohibited.  
48 TECHNICAL SPECIFICATIONS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TECHNICAL SPECIFICATIONS 49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
250 Crossways Park Drive, Woodbury, New York 11797  
Harman Consumer Group, Inc.:  
2, route de Tours, 72500 Château-du-Loir, France  
© 2008 Harman Kardon, Incorporated  
Part No.: CQX1A1382Z  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Groupe SEB USA T FAL Iron FV5110 User Manual
Haier Flat Panel Television L1509A A User Manual
Hamilton Beach Humidifier 05518C User Manual
Hans Grohe Plumbing Product 31073XX1 User Manual
Healthrider Home Gym HREX04981 User Manual
Hearth and Home Technologies Indoor Fireplace SL 550TRS E User Manual
Honeywell Barcode Reader 1200g User Manual
Hotpoint Dishwasher BFV620 User Manual
Hunter Fan Fan 22068 User Manual
Image Treadmill IMTL591050 User Manual