CP35 QUICK-START GUIDE
Thank you for purchasing a Harman Kardon CP 35 Home Theater System. This
Quick-Start Guide will help you with a basic system installation. For detailed
information on any step in this Guide, please refer to the pages referenced in
the Owner’s Manual for the AVR 335, which is part of this system. We strongly
recommend that you read all four Owner’s Manuals for complete details on
how to install, configure and operate the AVR 335, DVD 31, HKTS 14 and
HKS 4, as well as for the important safety information they contain. You should
also read the Owner’s Manual for the included RCP 2 system remote.
FRONT
RIGHT
SPEAKER
CENTER
SPEAKER
(Green)
FRONT
LEFT
SPEAKER
(Red)
(White)
SURROUND
RIGHT
SPEAKER
Figure 1 – Speaker Placement
The colors shown for each speaker correspond to
the matching output terminal connection on the back
of the AVR 335 (see page 7).
(Gray)
SUBWOOFER
(Purple)
SURROUND
LEFT
SPEAKER
Connections Color Guide
Audio Connections
Front
Left
Right
SURROUND
BACK
RIGHT
SPEAKER
(Tan)
(Blue)
Center
SURROUND
BACK
Surround
LEFT
SPEAKER
(Brown)
Subwoofer
Surround Back
Digital Audio Connections
Coax
Step 1. Place your speakers in the listening room
(see page 16).
Optical
Video Connections
Composite
S-Video
Match the colored jacks on the AVR 335 to the appropriate
jacks on your source equipment or speakers. The colors are
standardized, but not all equipment or connectors use them.
SPEAKER PLACEMENT
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Antenna
AM Antenna
91329
240
Figure 4 – DVD Connections
Dashed lines (– – – –) indicate coax
and optical digital audio connections.
Choose either type (but not both) for
each digital audio source.
Figure 5 – Connecting EzSet+
Microphone
Step 4. Connect AM and FM antennas, as shown above (see page 14).
Step 5. Connect the DVD 31 to the AVR 335 as shown above:
AUDIO connections: Connect the L/R Audio Out jacks on the DVD
to the L/R DVD Audio in jacks on the AVR.
back of this Guide. Plug all sources into an AC power outlet.
at your normal listening position. If desired, the mike may be
attached to a standard camera tripod using the threads on the
bottom of the mike. Follow the instructions on pages 20–21 of
the Owner’s Manual, which contains the steps needed to activate
the system. As EzSet+ senses the output of each speaker, you will
hear loud test signals. This is a normal part of the EzSet+ process.
When the on-screen menu indicates that setup is complete, your
system is adjusted for output levels, delay times and speaker set-
tings. Unplug the microphone and store it for future use.
Step 10. If you are using a component video connection to a digital television,
set the DVD 31’s output to Progressive Scan, as shown on page 17
of the DVD 31 manual.
Step 7. Connect the AVR to your TV or video display. You must make a
composite, “S” or component video connection corresponding
corresponding to each video source device used in your system.
Remember to switch the TV to the correct input for each source.
NOTE: The AVR’s on-screen menus are not available when viewing
a component video connection. For that reason, a composite or
S-video connection is recommended, though not required, when
component video is used.
DIGITAL AUDIO connections: Use the enclosed coaxial interconnect
(orange connectors) to connect the Coaxial Digital Output on the
DVD to the Coaxial Digital 1 Input on the AVR.
VIDEO connections: Depending on the input available on your TV,
use either composite video (dotted yellow), S-video (dotted black)
or component video (dotted red/blue/green) connections. Only one
connection type is needed.
POWER: Plug the DVD’s AC power cord into the SWITCHED output
on the back of the AVR. Press the Main Power Switch on the DVD so
that it is ON (see page 17).
Basic Configuration
Step 8. Select digital inputs: Use the On-Screen Input Setup menu or the
front-panel Digital Select button and the arrow buttons to select an
optical or coaxial digital input, for any digital source of the DVD
(see page 18).
Step 11. Your system is configured – sit back and enjoy!
Step 6. Connect other source devices such as a VCR, Cable or Satellite set-
top box, HDTV receiver or audio recorder using the connections
shown in the Device Connection Options chart and Figure 6 on the
+
Step 9. Use
to configure and optimize your system.
Plug the EzSet+ microphone into the front-panel Headphones
Jack (Fig. 5). Place the microphone at the center of the room, or
SPEAKER AND DVD CONNECTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
VCR (Video 1)
R
TV or Video Monitor
S-Video
Cable or Sat or HDTV Set-Top Box (Video 2)
OUT
L
VIDEO
Video
Component Video
Component Video
L
R
Video
S-Video
Y
Pb
Pr
Y
Pb
Pr
IN
In/Rec
Out/Play
Optical
Coax
AUDIO RECORDER
Figure 6 – Source Component Connections
Dashed lines (– – – –) indicate coax and optical digital audio connections. Choose either type (but not both) for each
digital audio source.
REC/IN
PLAY/OUT
Dotted lines (••••) indicate component, composite or S-vdeo connections. Component video is the preferred connection
when available, but you may use any of the three types (but not more than one). When component, composite and
S-video sources are connected to the AVR, you must also connect all outputs from the AVR to your TV.
Device Connection Options: Recommended connections are shown in red, but connections may be made to best fit your system requirements. The Video 4, Coax 3 and Optical 3 inputs are on the front panel of the receiver.
Device
CD Player
DVD Player
VCR
Input Name
CD
Audio Input Connections
Audio Output Connections
Not required
Video Connections
Not required
CD L/R Inputs, Optical Digital 1, 2 or 3, or Coaxial Digital 1, 2 or 3
Coaxial Digital 1, 2 or 3, Optical Digital 1, 2 or 3, or DVD L/R Inputs
Video 1 L/R Inputs
DVD
Not required
DVD Component, Composite or S-Video
Video 1 Composite or S-Video Input and Output
Video 3 Composite or S-Video Input
Video 1
Video 1 L/R Outputs
Not required
Cable Box or Satellite Receiver Video 3
Video 3 L/R Inputs, Optical Digital 1/2/3*, or Coaxial Digital 1/2/3* Inputs
Audio Recorder
TV or Projector
Tape
Tape L/R Inputs, Optical Digital 1/2/3** or Coaxial Digital 1/2/3** Inputs
Not required
Tape L/R Outputs, Digital Optical** or Coaxial Outputs** Not required
Not required Monitor-Out Component, Composite and/or S-Video
Not applicable
Check with your cable company to determine whether digital audio is available for all channels. It may be necessary to make BOTH analog and digital connections if it is not.
Digital audio recorders only.
*
**
®
SOURCE COMPONENT CONNECTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
|