2” CLEAR WATER PUMP
5.5 HP - OVERHEAD VALVE ENGINE
Model 93662
ASSEMBLY AND OPERATING INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright© 2005 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
PERSONAL SAFETY
1.
Stay alert. Watch what you are doing, and use common sense when operat-
ing a power tool. Do not use a power tool while tired or under the influence
of drugs, alcohol, or medication. A moment of inattention while operating power
tools may result in serious personal injury.
2.
3.
4.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
Avoid accidental starting. Be sure the Power Switch (98A) is in its “OFF”
position before moving the Water Pump and before performing any service,
maintenance, or cleaning procedures on the unit.
Remove adjusting keys or wrenches before turning the Water Pump on. A
wrench or a key that is left attached to a rotating part of the machine may result in
personal injury.
5.
6.
Do not overreach. Keep proper footing and balance at all times. Proper footing
and balance enables better control of the power tool in unexpected situations.
Use safety equipment. Always wear eye protection. Always wearANSI
approved safety impact goggles when using this product. ANSI approved
hearing protection must also be used.
TOOL USE AND CARE
1.
2.
Do not force the tool. Use the correct tool for your application. The correct tool
will do the job better and safer at the rate for which it is designed.
Do not use the Water Pump if the Engine’s Power Switch (98A) does not turn
it on or off. Any tool that cannot be controlled with its power switch is dangerous
and must be replaced.
3.
4.
Store idle tools out of reach of children and other untrained persons. Tools
are dangerous in the hands of untrained users.
Maintain tools with care. Properly maintained tools with a sharp cutting edge
are less likely to bind and are easier to control. Do not use a damaged tool. Tag
damaged tools “Do not use” until repaired.
5.
6.
Check for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tool’s operation. If damaged, have the tool
serviced before using. Many accidents are caused by poorly maintained tools.
Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one tool may become hazardous
when used on another tool.
SKU 93662
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE
1.
2.
Tool service must be performed only by qualified repair personnel. Service or
maintenance performed by unqualified personnel could result in a risk of injury.
When servicing a tool, use only identical replacement parts. Follow instruc-
tions in the “Inspection, Maintenance, And Cleaning” section of this manual.
Use of unauthorized parts or failure to follow maintenance instructions may create
a risk of electric shock or injury.
SPECIFIC SAFETY RULES AND PRECAUTIONS
1.
Your Warranty is voided if you do not put engine oil in the Engine’s crankcase
prior to its first use. Before each use, check the oil level. Never run the Engine
with low or no engine oil. Running the Engine with low or no oil will permanently
damage the unit.
2.
3.
Maintain labels and nameplates on the Water Pump. These carry important
information. If unreadable or missing, contact Harbor Freight Tools for a replace-
ment.
Make sure the Water Pump is located on a flat, level, sturdy surface capable
of supporting the weight of the Water Pump and any additional tools and
equipment.
4.
5.
Industrial applications must follow OSHA guidelines.
Never stand on the Water Pump. Serious injury could result if the Water Pump
is tipped.
6.
7.
8.
Never leave the Water Pump unattended when it is running. Turn off the Engine
before leaving.
Do not allow children and other unauthorized people to handle or play with
the Water Pump.
Use this Water Pump outdoors only. Do not operate the Water Pump in a closed
area or in a poorly ventilated area. When running, the Engine of this Water Pump
produces carbon monoxide, a colorless, odorless, toxic fume that, when inhaled,
can cause serious personal injury or death.
9.
1.
Do not force the Water Pump. This tool will do the work better and safer at the
speed and capacity for which it was designed.
FIRE AND EXPLOSION PRECAUTIONS
Gasoline fuel and fumes are flammable, and potentially explosive. Use proper
fuel storage and handling procedures. Always have multiple ABC class fire extin-
guishers nearby.
SKU 93662
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
3.
Keep the Water Pump, its Engine, and surrounding areas clean at all times.
When spills of fuel or oil occur, they must be cleaned up immediately. Dis-
pose of fluids and cleaning materials as per any local, state, or federal codes and
regulations. Store oil rags in a covered metal container.
4.
5.
Never store fuel or other flammable materials near the Water Pump.
Do not smoke, or allow sparks, flames, or other sources of ignition around
the Water Pump.
6.
Keep grounded conductive objects, such as tools, away from exposed, live
electrical parts and connections to avoid sparking or arcing. These events
could ignite fumes or vapors.
7.
8.
Do not refill the Fuel Tank while the Engine is running or while the Engine is
still hot. Do not operate the Water Pump with known leaks in the fuel system.
Use only Engine manufacturer recommended fuel and oil.
MECHANICAL PRECAUTIONS
1.
Prior to performing service, maintenance, or cleaning procedures, always
make sure the Engine’s Power Switch (98A) is in its “OFF” position. Allow
the Engine and Water Pump to completely cool. Then, remove the spark plug
from the Engine.
2.
3.
Do not alter or adjust any part of the Water Pump or Engine that is assembled
and supplied by the manufacturer.
Always follow and complete scheduled Water Pump and Engine mainte-
nance.
CHEMICAL PRECAUTIONS
1.
2.
Avoid contact with hot fuel, oil, exhaust fumes, and solid surfaces.
Avoid body contact with fuels, oils, and lubricants used in the Water Pump
and Engine. If swallowed, seek medical treatment immediately. Do not induce
vomiting if fuel is swallowed. For skin contact, immediately wash with soap and
water. For eye contact, immediately flush eyes with clean water.
NOISE PRECAUTION
Prolonged exposure to noise levels above 85 dBA is hazardous to hearing.
Always wear ANSI approved hearing protection when operating or working around
the Water Pump when it is running.
SKU 93662
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
MISC. PRECAUTIONS
1.
2.
WARNING: The brass components of this product contain lead, a chemical
known to the State of California to cause birth defects (or other reproductive
harm). (California Health & Safety code § 25249.5, et seq.)
People with pacemakers should consult their physician(s) before use. Elec-
tromagnetic fields in close proximity to heart pacemaker could cause pacemaker
interference or pacemaker failure. Caution is necessary when near engine’s mag-
neto or recoil starter.
3.
WARNING! The warnings and precautions discussed in this manual cannot cover
all possible conditions and situations that may occur. It must be understood by the
operator that common sense and caution are factors which cannot be built into this
product, but must be supplied by the operator.
SAVE THESE INSTRUCTIONS
UNPACKING
When unpacking, check to make sure all the parts shown on the Parts Lists on
pages 14 and 15 are included. If any parts are missing or broken, please call Harbor
Freight Tools at the number shown on the cover of this manual as soon as possible.
SKU 93662
For technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTIONS
CAUTION! Always make sure the Power Switch (98A) of the Engine is in its “OFF”
position prior to performing any service, maintenance, or cleaning of the Water
Pump or Engine.
To Add Engine Oil:
1.
IMPORTANT! Prior to first using the Water Pump, the Engine MUST be filled with
a high quality 10W-30 grade engine oil. (See Figure A.)
OIL DIPSTICK (65A)
MAXIMUM OIL LEVEL
MINIMUM OIL LEVEL
FIGURE A
2.
3.
To do so, unscrew and remove the Engine Oil Dipstick (65A). Pour approximately
2/3 quart of engine oil into the Dipstick Hole. Do not overfill. (See Figure A.)
Clean the Oil Dipstick (65A). Then screw the Dipstick fully back into the Dipstick
Hole. Unscrew and remove the Oil Dipstick again, and observe the level of en-
gine oil on the Dipstick. The oil level should appear between the “MINIMUM” and
“MAXIMUM” indicator marks on the Oil Dipstick. (See Figure A.)
4.
If necessary, continue adding engine oil, while rechecking the Oil Dipstick (65A),
until the oil level reaches the “MAXIMUM” indicator on the Oil Dipstick.
Do not exceed the “MAXIMUM” indicator mark on the Oil Dipstick.
(See Figure A.)
5.
When finished adding engine oil, carefully screw the Oil Dipstick (65A) back into
the Dipstick Hole. (See Figure A.)
SKU 93662
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
To Fill The Fuel Tank:
FUEL TANK CAP
(83A)
FUEL TANK
(84A)
FIGURE B
1.
2.
Prior to first using the Water Pump, the Fuel Tank (84A) MUST be filled with high
octane unleaded gasoline. (See Figure B.)
To do so, remove the Fuel Tank Cap (83A) and fill the Fuel Tank with unleaded
gasoline. Then, replace the Fuel Tank Cap. Thereafter, check the Fuel Tank (84A)
for the amount of unleaded gasoline. When necessary, refill the Fuel Tank.
(See Figure B.)
To Connect An Intake Hose & Discharge Hose To The Water Pump:
1.
The Intake Filter (21) that is provided with the Water Pump should be attached to
the end of the Intake Hose (not included) with a Hose Clamp that is provided with
the Intake Union Set (9). (See Figure C, next page.)
2.
To connect the other end of the Intake Hose to the Water Pump, slide the Coupling
Gasket onto the Hose Coupling of the Intake Union Set (9). Slide the Hose Clamp
and Hose Joint of the Intake Union Set (9) onto the end of the Intake Hose. Insert
the Intake Hose onto the Hose Coupling, and firmly tighten the Hose Clamp to
secure the Intake Hose onto the Hose Coupling. Then, screw the Hose Joint onto
the Intake Flange (14) of the Water Pump. (See Figure C.)
3.
To connect a 2” diameter Discharge Hose (not included) to the Water Pump, slide
the Coupling Gasket onto the Hose Coupling of the Discharge Union Set (9). Slide
the Hose Clamp and Hose Joint of the Discharge Union Set (9) onto the end of the
Discharge Hose. Insert the Discharge Hose onto the Hose Coupling, and firmly
tighten the Hose Clamp to secure the Discharge Hose onto the Hose Coupling.
Then, screw the Hose Joint onto the Discharge Flange (10) of the Water Pump.
(See Figure C.)
SKU 93662
For technical questions, please call 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
HOSE
COUPLING
HOSE
JOINT
INTAKE
FILTER
(21)
2” DIAMETER
INTAKE HOSE
(NOT INCLUDED)
COUPLING
GASKET
HOSE
CLAMP
HOSE
CLAMP
HOSE
COUPLING
HOSE
JOINT
2” DIAMETER
DISCHARGE HOSE
HOSE
CLAMP
COUPLING
GASKET
(NOT INCLUDED)
DISCHARGE FLANGE
(10)
INTAKE FLANGE
(14)
FIGURE C
SKU 93662
For technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
To Properly Locate The Water Pump:
1.
WARNING! Use this Water Pump outdoors only. Do not operate the Water
Pump in a closed area or in a poorly ventilated area. When running, the Engine
of this Water Pump produces carbon monoxide, a colorless, odorless, toxic
fume that, when inhaled, can cause serious personal injury or death.
2.
3.
Keep your work area clean and well lit. Cluttered and dark areas invite acci-
dents.
Do not operate the Water Pump in explosive atmospheres, such as
in the presence of flammable liquids, gases, or dust. The Water Pump
and its Engine can create sparks which may ignite the dust or fumes.
4.
5.
Make sure the Water Pump is located on a flat, level, sturdy surface capable of sup-
porting the weight of the Water Pump and any additional tools and equipment.
Route the Intake Hose with its Intake Filter (21) fully immersed in the water supply
source. Then, make sure to secure the Intake Hose in place to keep it from mov-
ing once the Water Pump is turned on. NOTE: The maximum suction lift of the
Water Pump is 26 feet. The Intake Hose should be kept as short as possible for
more efficient operation.
6.
Route the Discharge Hose to the desired discharge location. If necessary, connect
additional Discharge Hoses to direct the discharge to the desired location. Then,
secure the Discharge Hose in place to keep it from moving once the Water Pump
is turned on.
Note: The maximum discharge length of the Water Pump is 86 feet. The Discharge Hose
should be kept as short as possible for more efficient operation.
To Prime The Water Pump:
1.
The Water Pump MUST be primed with clean water prior to each use of the Pump.
To Prime the Water Pump, unscrew and remove the Priming Cap (11) located at
the top of the Discharge Flange (10). (See Figure D, next page.)
2.
Fill the Discharge Flange (10) to its top with clean water. Then, replace the
Priming Cap (11). (See Figure D.)
SKU 93662
For technical questions, please call 1-800-444-3353.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
PRIMING CAP (11)
DISCHARGE FLANGE (10)
FIGURE D
To Start And Stop The Engine:
Note: Only use this pump to pump unheated clean water. Other liquids may damage the
pump and/or be hazardous.
1.
2.
Once the Engine is started, the Water Pump will run continuously until the Engine
is turned off.
When finished using the Water Pump, turn off the Engine. Make sure to allow the
Water Pump and its Engine to completely cool before moving the Water Pump or
storing the unit.
REV 06j, 07f
SKU 93662
For technical questions, please call 1-800-444-3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
INSPECTION, MAINTENANCE, AND CLEANING
1.
2.
CAUTION! Always make sure the Power Switch (98A) of the Engine is in its “OFF”
position prior to performing any service, maintenance, or cleaning of the Water
Pump or Engine.
Before each use, inspect the general condition of the Water Pump. Check for loose
screws, misalignment or binding of moving parts, cracked or broken parts, loose
hose connections, and any other condition that may affect the safe operation of the
Water Pump. If abnormal noise or vibration occurs, have the problem corrected
before further use.
Do not use damaged equipment.
3.
4.
5.
6.
Before each use, check the Engine oil level in the Engine. If necessary, fill the
crankcase of the Engine with the proper amount and type of engine oil.
Before each use, check the Inlet Filter (21) for accumulated debris, rocks, and
other objects that may clog the Inlet Filter.
If the Water Pump is not in use due to dry conditions, etc., prime the Water
Pump and activate the unit once every three months.
In cold weather, when if the Water Pump is not in use, protect the interior of the
Pump from freezing by draining any remaining water and pumping a permanent
type automotive antifreeze containing a rust inhibitor through the system. A 50%
mixture with clean water is recommended. Make sure to flush the system with a
neutralizing liquid prior to reuse of the unit.
7.
To clean the Water Pump, use a garden hose and a mild detergent. Avoid intro-
ducing water into the interior parts of the Engine.
8.
When storing the Water Pump, make sure to store the unit in a clean, dry, safe
location out of reach of children and other unauthorized people.
9.
Engine maintenance: Refer to the Engine manufacturer’s manual for complete
inspection, maintenance, and cleaning instructions.
10.
CAUTION! All maintenance, service, or repairs not mentioned in this manual
must only be performed by a qualified service technician.
SKU 93662
For technical questions, please call 1-800-444-3353.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
1. Take the engine to a
qualified service technician.
NOTE: If the water pump still does not operate
properly, take the pump to a qualified service technician.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND
ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE
MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY
OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY
CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER AS-
SUMES ALL RISKS AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGI-
NAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 93662
For technical questions, please call 1-800-444-3353.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST & ASSEMBLY DIAGRAM - WATER PUMP
Part
Description
Qty.
Part
Description
Qty.
1
2
3
4
5
6
7
8
9
Cover
Hex Bolt
O-Ring
1
1
13 Washer
9
1
1
1
2
1
8
4
4
1
1
14 Intake Flange
15 Check Valve
3# O-Ring
3#-1 O-Ring
16 Tube Frame
17 Screw
18 Oscillation Absorber
19 Bolt
20 Gasoline Engine
21 Intake Filter
4
1
1
1
1
1
1 ea.
2
1
Mechanical Seal
Impeller
Casing
Pump Housing
Discharge Packing
Intake/Discharge Union Set
10 Discharge Flange
11 Priming Cap
12 Bolt
9
21
Note: Some parts are listed and shown for illustration purposes only, and are not available
individually as replacement parts.
SKU 93662
For technical questions, please call 1-800-444-3353.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST - ENGINE
Part
2A
3A
4A
5A
6A
7A
8A
9A
Description
Qty.
4
4
1
2
2
3
2
1
2
1
1
1
1
1
1
4
1
1
1
1
1
2
1
1
1
2
1
2
2
2
2
1
1
1
1
1
1
2
1
1
1
1
1
1
2
1
1
1
1
Part
Description
Qty.
1
1
1
1
1
1
2
1
2
2
1
2
1
1
2
2
1
6
2
2
1
4
2
2
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
2
1
2
1
1
1
1
2
1
Cylinder Head Bolt
51A Flywheel Magneto
52A Cylinder Block
53A Speed Control Lever
54A Governor Arm
55A Governor Spring
56A Governor Support
57A Bolt (M6-15)
Cylinder Head Cover Bolt
Cylinder Head Cover
Lock Nut
Adjusting Screw
Rocker Arm
Rocker Arm Bolt
Valve Push Rod Guiding Board
58A Oil Alert Nut
59A Plug (M10-15)
60A Plug Washer
61A Oil Alert
62A Bolt (M6)
63A Crankshaft
64A Crankshaft Gear
65A Oil Dipstick
66A Oil Dipstick Seal Ring
67A Gear Casing
68A Bolt (M8-35)
10A Valve Push Rod
11A Cylinder Head
12A Carburetor Shield
13A Carburetor Packing
14A Carburetor Assembly
15A Air Cleaner Case
16A Air Cleaner Seal
17A Bolt (M6)
18A Air Cleaner Cover
19A Air Cleaner Element
20A Air Cleaner Separator
21A Choke Lever
22A Carburetor Packing II
23A Stud Bolt (M6-109)
24A Intake Valve
25A Exhaust Valve
26A Cylinder Head Gasket
27A Exhaust Pipe Stud
28A Spark Plug
69A Gear Case Packing
70A Bearing
71A Camshaft Assembly
72A Locating Pin
73A Oil Seal
74A Connecting Rod Bolt
75A Connecting Rod Cap
76A Connecting Rod
77A Piston
78A Compression Ring 1
79A Compression Ring 2
80A Oil Scraper Ring
81A Piston Pin
82A Piston Pin Circlip
83A Fuel Tank Cap
84A Fuel Tank
85A Fuel Pipe
86A Fuel Pipe Protecting Tube
87A Fuel Filter
29A Valve Guide
30A Valve Spring
31A Rocker Shaft Circlip
32A Anti-Wear Valve Stem Protector
33A Cylinder Head Cover Packing
34A Governor Spring
35A Bolt
36A High Tension Line
37A Ignition Coil
38A Nut (Special 14mm)
39A Starter Ratchet Spring
40A Start Rope
41A Start Handle
42A Starting Case Assembly
43A Spiral Spring
44A Starting Wheel
45A Circlip
46A Starting Ratchet
47A Friction Plate Screw
48A Cover
88A O-Ring
89A Fuel Valve
90A Bolt (M5-8)
91A Complete Outside Cover
92A Bolt (M5-8)
93A Bolt (M4-8)
94A Complete Silencer
95A Exhaust Filter Cartridge Assy.
96A Exhaust Pipe Packing
97A Bolt (M5-38)
49A Starter Pulley
50A Cooling Fan
98A Power Switch
Engine Maintenance
The Spark Plug is LD(F7RTC), BPR6ES(NGK). The Spark Plug gap setting is 0.7--0.8mm. The Intake
Valve clearance is 0.15mm, Exhaust Valve clearance is 0.20mm. The valve clearance needs to be ad-
justed after 100 hours. Change the engine oil after 20 hours or internal one month.
SKU 93662
For technical questions, please call 1-800-444-3353.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY DIAGRAM - ENGINE
REV 08c
SKU 93662
For technical questions, please call 1-800-444-3353.
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
Emission Control System Warranty
California and United States Emission Control Defects Warranty Statement
The CaliforniaAir Resources Board (herein CARB), the United States Environmental ProtectionAgency (herein EPA), and Harbor Freight
Tools® (herein HFT) are pleased to explain the emission control system warranty on your 1995 and later Small Off-Road Engine (herein
engine). In California, the engine must be designed, built and equipped to meet the State’s stringent anti-smog standards. Elsewhere
within the United States, new off-road, spark-ignition engines certified for model year 1997 and later, must meet similar standards set
forth by the EPA. HFT must warrant the emission control system on your engine for the periods of time described below, provided
there has been no abuse, neglect or improper maintenance of your engine.
Your emission control system may include parts such as the carburetor or fuel-injection system, and the ignition system. Also included
may be hoses, belts, connectors and other emission-related assemblies.
Where a warrantable condition exists, HFT will repair your engine at no cost to you including diagnosis, parts and labor.
Manufacturer’s Warranty Coverage
The 1995 and later engines are warranted for two (2) years. If any emission-related part on your engine is defective, the part will be
repaired or replaced by HFT.
Harbor Freight Tools Emission Control Defects Warranty Coverage
Engines are warranted for a period of two (2) years relative to emission control parts defects, subject to the provisions set forth below.
If any emission related part on your engine is defective, the part will be repaired or replaced by HFT.
Owner’s Warranty Responsibilities
-
As the engine owner, you are responsible for the performance of the required maintenance listed in your Owner’s Manual. HFT
recommends that you retain all receipts covering maintenance on your engine, but HFT cannot deny warranty solely for the lack
of receipts or for your failure to ensure the performance of all scheduled maintenance.
-
-
As the engine owner, you should, however, be aware that HFT may deny you warranty coverage if your engine or a part has failed
due to abuse, neglect, improper maintenance, or unapproved modifications.
You are responsible for shipping your engine to a HFT warranty station as soon as a problem exists. Contact the HFT Customer
Service department at the number below to make shipping arrangements. The warranty repairs should be completed in a reason-
able amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you should contact the Harbor Freight Tools Customer
Service Department at 1-800-444-3353.
Harbor Freight Tools Emission Control Defects Warranty Provisions
1. Length of Coverage
HFT warrants to a first retail purchaser and each subsequent purchaser that the engine is free from defects in materials and
workmanship that cause the failure of warranted parts for a period of two (2) years after the date of delivery to the first retail
purchaser.
2. No Charge Repair or Replacement
Repair or replacement of any warranted part will be performed at no charge to the owner if the work is performed through a warranty
station authorized by HFT. For emissions warranty service, contact the HFT Customer Service Department at 1-800-444-3353.
3. Consequential Damages Coverage
Coverage under this warranty shall also extend to the failure of any engine components caused by the failure of any warranted
part while it is still covered under this warranty.
4. Coverage Exclusions
Warranty claims shall be filed in accordance with the provisions of the HFT warranty policy explained in the box at the top of the
previous page. HFT shall not be liable for any loss of use of the engine, for any alternative usage, for any damage to goods, loss
of time, or inconvenience. Warranty coverage shall also be excluded for any part which fails, malfunctions, or is damaged due to
failure to follow the maintenance and operating instructions set forth in the Owner’s Manual including, but not limited to:
(a) use of parts which are not authorized by HFT
(b) improper installation, adjustment or repair of the engine or of any warranted part unless performed by an authorized warranty
center
(c) failure to follow recommendations on fuel use contained in the Owner’s Manual
(d) improper or inadequate maintenance of any warranted parts
(e) repairs performed outside of the authorized warranty service dealers
(f) alterations by changing, adding to or removing parts from the engine.
SKU 93662
For technical questions, please call 1-800-444-3353.
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Emission Control System Warranty - continued
Harbor Freight Tools Emission Control Defects Warranty Provisions
5. Service and Maintenance
Component parts which are not scheduled for replacement as required maintenance or are scheduled only for regular inspection
to the effect of “repair or replace as necessary” are warranted for the warranty period. Any warranted part which is scheduled
for replacement as required maintenance is warranted for the period of time up to the first scheduled replacement point for that
part. Any replacement part, provided it is equivalent in durability and performance, may be used in performance of maintenance
or repairs. The owner is responsible for commissioning a qualified technician/mechanic to perform all required maintenance, as
outlined in the Inspection, Cleaning, and Maintenance section on page 17 of this manual.
6. Warranted Parts
1) Fuel Metering System
i)
Carburetor and its internal parts.
ii) Fuel pump (if so equipped).
iii) Cold start enrichment system.
2) Air Induction System
i)
Intake pipe/manifold.
ii) Air cleaner.
3) Ignition System
i)
Spark plug.
ii) Magneto ignition system.
4) Catalyst System (if so equipped)
i)
Exhaust pipe stud.
ii) Muffler.
iii) Catalytic converter (if so equipped).
5) Miscellaneous items Used in Above Systems
i)
Vacuum, temperature and time sensitive valves and switches.
ii) Hoses, belts, connectors, and assemblies.
PUMP PERFORMANCE FLOW CHART
SKU 93662
For technical questions, please call 1-800-444-3353.
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
|