”
GUM BALL MACHINE- 9
92336
GUM BALL MACHINE w/STAND
”
15
92337
ASSEMBLY INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright © 2004 by Harbor Freight Tools® All rights reserved. No portion of this
.
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Maintain products with care. Keep Gumballs filled in globe. Empty coins
out of lower portion when refilling to prevent over filling.
7. Children should be supervised. Letting a child operate the Gumball
Machine is fun for all but caution should be observed. Allowing the child to
dispense and chew more than one Gumball at one time could cause
choking. Coins could be swallowed. Both the 9” and the 15” Gumball
Machine on the Stand could be pulled over by the child, causing personal
injury. It is best to supervise the operation of the Gumball Machine. Make
sure children keep their hands clear of the dispensing area to avoid getting
hands or fingers caught. Harbor Freight Tools is not responsible for injuries
caused by this product.
8. Caution when refilling Gumballs. Avoid sharp edges on the inside of the
cast metal base when disassembling and assembling this product. Caution:
The Globe is made of glass. Set Carefully on the table or workbench and
avoid accidently hitting the glass or letting it roll off the counter.
Warning:The warnings, cautions,and instructions discussed in this instruction
manual cannot cover all possible conditions and situations that may occur. It
must be understood by the operator that common sense and caution are
factors which cannot be built into this product, but must be supplied by the
operator.
Unpacking
When unpacking the Gumball Machine, check to make sure that all parts
are included as shown in the parts list. If any parts are missing or broken,
please call Harbor Freight Tools at the number below. Thoughly clean all
parts with anti-bacterial soap and water before using. Be sure to thoroughly
dry all parts before reassembling.
Operating Instructions
Filling Machine:
1. Works with all coins, pennies, nickels, dimes and quarters. Dispenses
Gumballs, Peanuts, Jelly Beans, and more. To add Gumballs or other small
objects to the Gumball Machine, you must first unscrew the Plug (1) at the
top and remove the Cap (2). Pour Gumballs (not included) slowly into the
Glass Globe (5). Reassemble the Cap (2) and Plug (1). See Figure 1.
Plug (1)
Glass Globe (5)
with Gumballs
Cap (2)
Figure 1
SKU 92336-SKU92337
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal of Coins:
1. Remove the Plug (1), Cap (2), Nut (3), Retaining Ring (4), Glass Globe
(5), Gasket (6), Brush Plate (7), and Adjustable Wheel (8). Hold Body (9)
firmly and lift up. You should be able to reach the coins. After removing the
coins, carefully reassemble the above parts in the reverse order.
See illustration on Page 6 and Figure 2.
Glass Globe (5)
Nut (3)
Retaining Ring (4)
Gasket (6)
Cap (2)
Brush Plate (7)
Adjustable
Wheel (8)
Body (9)
Figure 2
Varying the Amount of Gumballs to be Dispensed:
1. Loosen screws on the Adjustment Wheel (8). Adjust the size of the
opening to the desired amount of Gumballs to be dispensed. Tighten screws
and replace assembly. See Figure 3.
Coin Slot
Face Plate of the
Coin Mechanism (10)
Handle
Figure 4
Figure 3
Operating the Machine:
1. Place the coin into the slot (See Figure 4) on the Face Plate of the Coin
Mechanism (10). Turn the Handle one revolution. To dispense without using
coins, with the Globe off, lift the Coin Mechanism (10) upward from it’s
position. Turn over. Unscrew and remove the brass colored restraining arm
on the back of the Coin Mechanism (10). Reassemble. See Figures 4 & 5.
Face Plate of the
Coin Mechanism (10)
Restraining Arm
Figure 5
SKU 92336-SKU92337
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching the Stand to SKU 92337:
1. Attach the four Feet (12) to Center Disk (13) with four Screws (14) and
Nuts (15). See Figure 6.
2. Twist on Center Extension (16) to Center Disk (13). Twist Top Extension
(17) to Center Extension (16) and then the top threaded end to the Base
Plate (11) of the Gumball Machine. Tighten all hardware and connections.
See Figures 7 & 8.
Threaded
area to
attach to
Gumball
Machine.
Center Extension (16)
Feet (12)
Top Extension (17)
Top
Extension (17)
Screw (14)
Nut (15)
Center
Extension (16)
Center Disk
(13)
Figure 6
Feet (12)
Figure 7
Gumball Machine
Base Plate (11)
Figure 8
The 15” Gumball Machine with Stand fits well in a corner or out of the traffic area,
and must be located on a flat, level floor surface.
Maintenence
1. To remove dust, use a damp cloth. To remove grease or oil, use a detergent
based cleaning solvent, rinse with damp cloth, and dry.
SKU 92336-SKU92337
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
Part # Description
Qty.
Part #
Description
Qty.
12
13
14
15
16
17
Feet
4
1
4
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
Plug
Center Disk
Screw
Cap
3
Nut
Nut
4
Retaining Ring
Globe
Center Extension
Top Extension
5
Gasket
6
Brush Plate
Adjustable Wheel
Body
Coin Mechanism
Base Plate
7
8
9
Parts Identification
10
11
Part 1
Part 2
Part 17
Part 3
Part 4
Part 5
Part 16
Part 14
Part 6
Part 12
Part 7
Part 8
Part 10
Part 13
Part 9
Part 15
Part 11
NOTE: Some parts are listed and shown for illustration purposes only and are not
available individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM INTHIS MANUAL
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO
MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THat
ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING
OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO,
OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts.
SKU 92336-SKU92337
For technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
|