BREAKER HAMMER
WITH PORTABLE CASE
Model 46935
ASSEMBLY and OPERATING
INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright © 2002 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
REV 04/03
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Maintain tools with care. Keep tools sharp and clean for better and safer performance.
Follow instructions for lubricating and changing accessories. Inspect tool cords periodically
and, if damaged, have them repaired by an authorized technician.The handles must be
kept clean, dry, and free from oil and grease at all times.
11. Disconnect power. Unplug tool when not in use.
12. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches are
removed from the tool or machine work surface before plugging it in.
13. Avoid unintentional starting. Be sure the Switch Knob #87 is not depressed when not
in use and before plugging in. Do not carry any tool with the switch depressed, whether
it is plugged in or not.
14. Stay alert. Watch what you are doing, use common sense. Do not operate any tool when
you are tired.
15. Take caution as some woods contain preservatives such as copper chromium
arsenate (CCA) which can be toxic.When cutting these materials extra care should be
taken to avoid inhalation and minimize skin contact.
16. Check for damaged parts. Before using any tool, any part that appears damaged should
be carefully checked to determine that it will operate properly and perform its intended
function.Check for alignment and binding of moving parts; any broken parts or mounting
fixtures;and any other condition that may affect proper operation. Any part that is damaged
should be properly repaired or replaced by a qualified technician. Do not use the tool if
any switch does not turn On and Off properly.
17. Guard against electric shock. Prevent body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerator enclosures.
18. Replacement parts and accessories. When servicing, use only identical replacement
parts. Use of any other parts will void the warranty. Only use accessories intended for
use with this tool. Approved accessories are available from Harbor Freight Tools.
19. Do not operate tool if under the influence of alcohol or drugs. Read warning labels
on prescriptions to determine if your judgment or reflexes are impaired while taking drugs.
If there is any doubt, do not operate the tool.
20. People with pacemakers should consult their physician(s) before using this product.
Electromagnetic fields in close proximity to a heart pacemaker could cause interference
to or failure of the pacemaker.
21. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities, contain chemicals known [to the State of California]
to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
- Lead from lead-based paints
- Crystalline silica from bricks and cement or other masonry products
- Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals: work in a well ventilated area, and work
with approved safety equipment, such as those dust masks that are specially designed
to filter out microscopic particles.
(California Health & Safety Code § 25249.5, et seq. )
SKU 46935
For technical questions, please call, 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
22. Maintenance. For your safety, maintenance should be performed by a qualified technician.
23. Use proper size and type extension cord. If an extension cord is required, it must be of
the proper size and type to supply the correct current to the tool without heating up.
Otherwise, the extension cord could melt and catch fire, or cause electrical damage to
the tool. See the chart below for appropriate extension cord size. Longer extension
cords require larger size wire. If you are using the tool outdoors, use an extension cord
rated for outdoor use (signified by “WA” on the jacket).
RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS*
(120 VOLT)
NAMEPLATE
AMPERES
EXTENSION CORD LENGTH
(At Full Load)
25
Feet
18
18
18
18
16
14
12
50
Feet
18
18
18
16
14
12
10
75
Feet
18
18
16
14
12
10
-
100
150
Feet
16
14
12
12
-
Feet
18
16
14
12
10
-
0 – 2.0
2.1 – 3.4
3.5 – 5.0
5.1 – 7.0
7.1 – 12.0
12.1 – 16.0
16.1 – 20.0
-
-
-
* Based on limiting the line voltage drop
to five volts at 150% of the rated amperes.
Note: Performance of this tool (if powered by line voltage) may vary depending on
variations in local line voltage. Extension cord usage may also affect tool performance.
Warning:The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be understood
by the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
Unpacking
When unpacking, make sure the parts listed on page 7 are included. If parts are missing or
broken, call Harbor Freight at the number on the cover of this manual as soon as possible.
Maintenance
Warning!! Make sure the Breaker Hammer is unplugged before doing any maintenance.
1.
Wipe the tool with a lint free cloth after each use. Remove all dust and grit from the tool.
2.
Add a drop or two of a lightweight oil to the Switch assembly area to lubricate the
Switch Knob (#87).
3.
Examine the tool before each use. Make sure the Chisel Bit is sharp and not dull or
cracked. Replace worn or broken bits with approved replacement bits from Harbor
Freight Tools.
4.
Store in temperatures no lower than 50-60° F.
REV 11/06; 02/07
SKU 46935
For technical questions, please call, 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Installing a Chisel.
Figure 1
Chisels come with or without collars. Figure 1 shows
installation of a chisel without a collar (the two included chisels
are without a collar). Figure 2 shows installation of a chisel
with a collar.
Without a Collar:
1.
Pull the retaining ring to the side just far enough to allow
the bit to be inserted, as shown in Figure 1.
2.
3.
Insert the bit. Slide the chisel in as far as it will go.
Pull the retaining ring down approximately 120° until it
contacts the housing. Physically check that the chisel is
secure before operating.
Retaining
Ring
Note: If the Chisel Bit doesn’t slide in easily, apply some grease
on the loading end of the Chisel Bit.
With a Collar:
1.
Pull the retaining ring open about 30-40° to the second
engaging position as shown in Figure 2.
2.
3.
Insert the collared chisel.
Return the retaining ring to close to its original position
to lock the chisel in place. Physically check that the chisel
is secure before operating.
Figure 2
Before each use, check the Chisel for cracks or other dam-
age: Never use a damaged Chisel.
Make sure you only use sharp tipped chisels.
Retaini
Ring
Dull tipped chisels can cause unnecessary
chisel movement resulting in tool wear, and
possible injury.
REV 11/03; REV 06/04
SKU 46935
For technical questions, please call, 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation (continued)
Warning!! Always wear ANSI approved impact safety goggles. Wear a full face shield if you
are producing metal filings or wood chips. Wear an ANSI approved dust mask or
respirator when working around metal, wood, and chemical dusts and mists. Always
wear ear protection. Ear protection is required for any other persons in the work
area.
Warning!! Be aware of flying concrete chips. Keep all spectators clear of the work area.
Warning!! Do not operate this tool if you have back, neck, wrist, or other conditions or injuries
that will be aggravated by the severe jerking forces that this tool exerts upon its
operator.
Warning!! If the Breaker Hammer ever gets out of your control, immediately release the Switch
Knob (87).
Note: Use the weight of the Breaker Hammer to help you break up concrete. Use the tool in
the vertical position whenever possible. This tool was intended to break up larger pieces of
concrete.
IMPORTANT - READ BEFORE USE
This Breaker Hammer may have decreased performance for a brief period at the beginning
of each use. This warmup period lasts approximately 3-5 minutes. This happens because
the grease inside the tool may be somewhat thick, preventing the tool from operating at full
efficiency while the motor is cold. This is perfectly normal and does not indicate a problem.
To help reduce this effect, we recommend storing this equipment in temperatures no lower
than 50-60° F.
Chipping a Straight Line
1.
Use chalk or another suitable writing material and mark you work surface to delineate
the area you intend to hammer.
2.
3.
Plug in the Breaker Hammer.
Grasp the handles firmly with both hands. When you are sure that no people or animals
are in the vicinity, and it’s safe to begin, depress the Switch Knob (#87).
4.
5.
The Breaker Hammer will begin to break the top layer of concrete. If you push down, it
will begin to break the next layer as well.
Keep moving the Breaker Hammer along the line you want to section, breaking concrete
as you go. If the Breaker Hammer jumps off of the line or section, release the Switch
Knob (#87) and reposition the Breaker Hammer.
6.
When you are finished, release the Switch Knob (#87) and unplug the Breaker Hammer.
Breaking up Concrete.
1.
2.
Place the bit on the center of a piece of concrete.
Grasp the handles firmly with both hands. When you are sure that no people or animals
are in the vicinity, and it’s safe to begin, depress the Switch Knob (#87).
3.
4.
As you break the concrete into big chunks, release the Switch Knob (#87)and move to
other large pieces until all of the larger pieces are broken. Do not try to break up smaller
pieces with this tool as it is too powerful and aggressive to control on small pieces.
When you are finished, release the Switch Knob (#87) and unplug the Breaker Hammer.
REV 12/04
SKU 46935
For technical questions, please call, 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
Part
No.
1
2
3
4
5**
6
7
8**
9
10
11*
12
13
14
15
16
17
18*
19
20
21
22**
23
24
25
26
27
28
29
30
31
Description
Qty
Part
No.
32**
33
34
35**
36
37**
38
39
40**
41
42
43
44
45
46
47
48
49
50
Description
Qty
Part
No.
63**
64
Description
Qty
Screw
Cover
4
1
1
1
1
1
1
1
1
4
1
1
1
1
2
1
1
1
1
2
1
1
1
2
9
2
1
2
1
1
1
Spring
1
1
1
2
1
3
3
3
2
1
1
2
1
1
1
2
2
1
2
2
2
2
2
1
1
1
9
1
1
1
2
Rubber Seal
Bearing
Fixing Sheath
1
1
1
Fixing Sheath
Hammer Cylinder
O-ring
Clamp Base
Spring
Washer
Nut
Rubber Washer
Pin
Clamp Frame
Roll Pin
Shell
Wire Protector
Stator
Stator Compressor
Screw
Rotor
Wire Fixing Board
Carbon Brush
Screw
Carbon Brush Holder
Screw
Wind Lead Ring
Vane
Tail Cover
Screw
Crankshaft Box
Connecting Rod
Fixing Ring
Piston
Spring Hammer
O-ring
Cylinder Box
Screw
Bearing
Pin
Felt Washer
Bearing
Axle
Bearing Ass’y.
Gear
65
67
68*
69**
70**
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
Crankshaft
Bearing
Seal Washer
Seal Cover
Right-down Cover
Screw
Screw
Right Balancing
Nut
Switch Box
Switch
Switch Sheath
Screw
Switch Box Cover
Capacitor
Terminal
Cable Clip
Screw
1
2
1
1
1
4
4
1
2
1
1
1
2
1
1
1
1
2
1
1
1
1
1
4
2
1
4
Bearing
Adjust Washer
Snap Ring
Gear
Seal Spacer
Gear Box
Shock Absorber
Screw
Spline Ass’y.
Spline Axle
Nut
Left Balancing
Fixing Sheath Washer
Fixing Sheath
51
52
53
54
55
56
57
58
Cable
Switch Knob Base
Switch Knob
Roll Pin
Right Handle
Screw
Nut
Left Handle
Screw
59*
60
61
Bearing
Nut
Rear Cover
Washer
92
93
62
94*
95**
Bearing Kit
Seal Kit
Parts with one or two asterisks are not available individually. You must purchase the
parts kits.
#94* - Bearing Kit includes part numbers 11*, 18*, 59*, 68*.
#95** - Seal Kit includes part numbers 5**, 8**, 22**, 32**, 35**, 37**, 40**, 63**, 69**,
70**
NOTE: Some parts are listed and shown for illustration purposes only and
are not available individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM INTHIS MANUAL
AS A REFERENCETOOL ONLY. NEITHERTHE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REP-
RESENTATION ORWARRANTY OF ANY KINDTOTHE BUYERTHAT HE OR SHE IS QUALIFIEDTO MAKE
ANY REPAIRSTO THE PRODUCT ORTHAT HE OR SHE IS QUALIFIEDTO REPLACE ANY PARTS OFTHE
PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL RE-
PAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSEDTECH-
NICIANS AND NOT BY THE BUYER.THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF
HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTSTHERETO.
REV 06/04; 02/05
SKU 46935
For technical questions, please call, 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Drawing
SKU 46935
For technical questions, please call, 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
|