AIR GRAVITY SPRAY
GUN, 20 OUNCES
Model 47016
ASSEMBLY and OPERATING
INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright © 2002 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor FreightTools.
For technical questions and replacement parts, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Dress properly. Do not wear loose clothing or jewelry as they can be caught in
moving parts. Protective, electrically nonconductive clothes and nonskid footwear are
recommended when working. Wear restrictive hair covering to contain long hair.
8. Use eye and breathing protection. Always wear ANSI-approved impact safety
goggles. Wear an ANSI-approved respirator when spraying.
9. Do not overreach. Keep proper footing and balance at all times. Do not reach over or
across running machines.
10. Maintain tools with care. Keep tools clean for better and safer performance. Follow
instructions for lubricating and changing accessories. Inspect tool cords and hoses
periodically and, if damaged, have them repaired by an authorized technician. The
handles must be kept clean, dry, and free from oil and grease at all times.
11. Disconnect power. When not in use disconnect from compressor.
12. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches
are removed from the tool or machine work surface before plugging it in.
13. Avoid unintentional starting. Do not carry any tool with your finger on the trigger,
whether it is plugged in or not.
14. Stay alert. Watch what you are doing, use common sense. Do not operate any tool
when you are tired.
15. Check for damaged parts. Before using any tool, any part that appears damaged
should be carefully checked to determine that it will operate properly and perform its
intended function. Check for alignment and binding of moving parts; any broken parts
or mounting fixtures; and any other condition that may affect proper operation. Any
part that is damaged should be properly repaired or replaced by a qualified
technician. Do not use the tool if any switch does not turn On and Off properly.
16. Guard against electric shock. Prevent body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerator enclosures.
17. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty.
18. Do not operate tool if under the influence of alcohol or drugs. Read warning
labels on prescriptions to determine if your judgment or reflexes are impaired while
taking drugs. If there is any doubt, do not operate the tool.
19. Use proper size and type extension cord. If an extension cord is required, it must be
of the proper size and type to supply the correct current to the air compressor without
heating up. Otherwise, the extension cord could melt and catch fire, or cause electrical
damage to the air compressor. Check air compressor manual.
20. Maintenance. For your safety, maintenance should be performed regularly by a
qualified technician.
21. Keep aware of air hoses. Be careful not to trip over air hoses while working. Check
air connections periodically.
REV 12/05
SKU 47016
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
22. Do not operate Spray Gun near open flames, pilot lights, heaters, or any other
heat source. Make sure you have adequate ventilation. Most solvents and paints
are extremely flammable, especially when sprayed. Never smoke cigarettes in the
same room you are working in.
23. Read labels on cleaning solvents and paint coatings. Chlorinated solvents such as
111-Trichloroethane and Methylene Chloride (also known as methyl-chloride) can
chemically react with aluminum and may explode. Many paint sprayers contain
aluminum. Contact solvent manufacturer or paint supplier if your are in doubt.
24. Paints and solvents may be harmful or fatal if swallowed or inhaled. Always use
a respirator when spraying. Avoid prolonged skin contact with solvents or paints as
they will irritate skin. After contact, immediately wash off exposed area with hot,
soapy water.
25. Check all Spray Gun Seals and Air Connection. Before use, make sure the
Lid (#23) is fully tightened to the Cup (#19). Make sure the air hose is securely
fastened to the Gun Body (#13).
Note: Performance of the compressor (if powered by line voltage) may vary depending
on variations in local line voltage. Extension cord usage may also affect tool perfor-
mance.
Warning:The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be under-
stood by the operator that common sense and caution are factors which cannot be
built into this product, but must be supplied by the operator. Additionally, read all of
the warnings and instructions provided in the instruction manual of the air
compressor you will be using.
WARNING: This product contains or, when used, produces a chemical known to the
State of California to cause cancer and birth defects or other reproductive harm.
(California Health & Safety Code § 25249.5, et seq.)
Unpacking
When unpacking, check to make sure the parts listed on page 8 are included. If any parts
are missing or broken, please call Harbor Freight Tools at the number on the cover of this
manual as soon as possible.
REV 12/05
SKU 47016
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Refer to Assembly Drawing on page 9.
1. To attach the Cup (#19), screw it onto the Connector (#43).
2. Screw the Air Connector (#40) into the bottom of the Body (#13).
Operation
Warning! Never allow the Spray Gun and Cup (#19) to lay on it’s side when the Cup (#19) is
full of
For best service, you should incorporate an oiler, a regulator, and an inline air filter, as shown
above. All are available at Harbor Freight Tools.
Note: It is recommended that you test the Spray Gun on scrap material, to become familiar
with the available adjustments, prior to use.
1. Remove the Lid (#23) on the Cup (#19) and add no more than 10 ounces of paint.
Replace the Lid (#23).
2. Connect the air hose to the Air Connector (#40) and set the pressure to 50 PSI. Do
not exceed 70 PSI.
3. Squeeze the Trigger (#31) to test the pattern.
4. Spray from a distance of approximately four to eight inches while keeping the Spray
Gun perpendicular to the ground.
5. Maintain your distance as you evenly move from side to side. Do not fan or arc the
Spray Gun or the paint will apply unevenly.
6. When you finish spraying, release the Trigger (#31), and disconnect the air hose.
7. Empty the Cup (#19). Never store the Cup (#19) with paint in it.
Warning! Even after the compressor is shut down, the Cup (#19) may still be pressurized.
Open it slowly and carefully.
Adjustments
1. You can fine tune the air pressure by slowly turning the Air Adjustment Screw Valve
Assy. (#A5). You may also adjust the pressure with the air compressor. Make sure
you do not exceed the recommended 70 PSI.
2. You can adjust the amount of fluid coming through the gun with the Fluid Control
Knob (#18). Loosen the Fluid Control Knob Lock (#17), make the adjustment, and
tighten the Fluid Control Knob Lock (#17).
Warning! Keep your hand away from theTrigger (#31) while adjusting jet shape.
3. To adjust the spray pattern, turn the Air Cap (#3).
SKU 47016
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem 1: Heavy top/bottom, or right/left pattern.
Cause:
Material buildup on Air Cap (#3).
Partially plugged Air Cap (#3) center holes.
Remove Air Cap (#3), soak in solvent, and wipe clean.
Material partially plugging Tip of Gun.
Solution:
Cause:
Solution:
Remove Air Cap (#3) and clean.
Cause:
Damaged Paint Needle (#14).
Solution:
Have a qualified technician replace the Paint Needle (#14) .
Problem 2: Heavy Center Pattern
Cause:
Too much paint.
Solution:
Reduce fluid flow with the Fluid Control Knob (#18).
Loosen the Fluid Control Knob Lock (#17), make the adjustment and
tighten the Fluid Control Knob Lock (#17).
Cause:
Solution:
Coating too thick.
Thin out coating.
Problem 3: Split spray pattern.
Cause:
Solution:
Cause:
Pressure too high.
Reduce air pressure at the regulator.
Not enough paint.
Solution:
Increase fluid flow with the Fluid Control Knob (#18).
Loosen the Fluid Control Knob Lock (#17), make the adjustment, and
tighten the Fluid Control Knob Lock (#17).
Problem 4: Jerky or fluttering spray.
Cause:
Solution:
Cause:
Solution:
Insufficient paint.
Fill Cup (#19).
Gun and Cup (#19) tipped at excessive angle.
Correct angle.
Problem 5: Air mixes with paint.
Cause:
Worn Air Adjustment Screw Valve Assy. (Set A).
Solution:
Have a qualified technician replace the Air Adjustment Screw Valve
Assy. (Set A)
SKU 47016
For technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT: Before using for the first time, the spray gun must be cleaned
using a solvent based thinner. If not removed, the red oil used by the
manufacturer for testing and corrosion protection may contaminate paint.
IMPORTANT: The Spray Gun must be cleaned immediately after use.
Improper cleaning is a common reason for the Spray Gun not to work.
Maintenance
Cleaning (Gun should be attached to compressor to complete the cleaning process)
Warning!! Do not use paint strippers on this unit as they will damage the aluminum. Never
allow the unit to lay on it’s side while paint is in the Cup (#19).
1. Empty paint from Cup (#19) and add small amount of clean solvent. Replace Lid (#23)
and shake Cup (#19) vigorously. At the lowest possible pressure, spray out the solvent into a
waste bucket (make sure you are wearing respirator and eye protection).
2. Empty Cup (#19) of remaining solvent and repeat the process until the Cup (#19) solvent
appears clean and free of the paint.
3. Disconnect air supply. Remove surplus solvent and wipe the Cup (#19) clean with a lint
free cloth.
Note: The Cup (#19) may be fully immersed in solvent for no more than 24 hours if needed.
4. Remove the Air Cap (#3) and the Ring (#4). Remove the Brass Ring (#5) and unscrew
the Fluid Nozzle (#6), and remove it. Use the Brush (#1) to clean the Paint Needle (#14)
with solvent. When replacing the Fluid Nozzle (#6), do not overtighten. Overtightening of the
Fluid Nozzle (#6) will result in leakage. Unscrew the Fluid Control Knob Lock (#17) and
remove the Fluid Control Knob (#18). Use the Brush (#1) to clean the gun body
opening that the Fluid Control Knob (#18) fits in, and clean all of the parts.
Reassemble gently. Parts may be damaged if forced into place.
Note: Always dispose of paints and solvents properly. Consult the local hazardous
waste authority for proper disposal procedures and sites.
REV 12/05
SKU 47016
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
Note: To order parts included in a lettered set, you must order the entire set.
Set A (Air AdjustingValve Assembly) includes parts A1, A2, A3, A4, A5, 34.
Set B (Cup) includes 19, 20.
Set C (Lid) includes 22, 23.
Set D (Needle Valve Assembly) includes 14, 15.
Set E (Spray Assembly) includes 34, 35, 36, 37, 38, 39.
Set F (Air Valve Assembly) includes 24, 25, 26, 27, 28, 29, 30.
Part No.
1
Description
Brush
Part No.
22
Description
Lid Nut
2
Wrench
23
Lid
3
Air Cap
24
Screw
4
Ring
25
Pin
5
6
7
8
Brass Cap
Fluid Nozzle
Packing Screw
Teflon Seal
Washer
26
27
28
29
Body
PC Seal
Valve
Valve
Spring
9
30
10
11
12
13
14
15
16
17
18
19
20
21
Spring
Brass Ring
Gasket
Gun Body
Paint Needle
Paint Needle Nut
Paint Needle Spring
Fluid Control Knob Lock 38
Fluid Control Knob
Cup
Adapter
Material Sleeve
31
32
33
34
35
36
37
Trigger
Screw
Pin
Washer
Spray Regulating Screw
Teflon Seal
Spray Regulating Nut
Control Knob
Countersunk Screw
Air Connector
Screw
Washer
Connector
Pin
39
40
41
42
43
44
PLEASE READTHE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM INTHIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBU-
TOR MAKES ANY REPRESENTATION ORWARRANTY OF ANY KINDTO THE BUYERTHAT HE
OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSEDTECHNICIANS AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
NOTE: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
SKU 47016
For technical questions, please call 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Drawing
Note: To order parts included in a lettered set, you must order the entire set.
Set A (Air Adjusting Valve Assembly) includes parts A1, A2, A3, A4, A5, 34.
Set B (Cup) includes 19, 20.
Set C (Lid) includes 22, 23.
Set D (Needle Valve Assembly) includes 14, 15.
Set E (Spray Assembly) includes 34, 35, 36, 37, 38, 39.
Set F (Air Valve Assembly) includes 24, 25, 26, 27, 28, 29, 30.
22
Set C (Lid)
23
1
19
Set B (Cup)
20
Set D (Needle Valve Assembly)
21
13
2
3
17
12
11
18
4
10
28
5
6
9
16
15
7
8
43
14
A1
A2
29
30
27
26
25
24
Set A
(Air
Adjusting
Valve
Assembly)
Set F (Air Valve Assy.)
34
41
42
31
32
34
A3
A4
35
Set E
(Spray
Assy.)
36
37
38
39
44
A5
40
SKU 47016
For technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
|