AUTOMATIC
PET WATER FOUNTAIN
Model 95781
AssEMbly ANd OPERATION INsTRUCTIONs
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
TO PREVENT sERIOUs INjURy, REAd ANd UNdERsTANd
All WARNINgs ANd INsTRUCTIONs bEFORE UsE.
©
®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
grounding prong or modify the plug in any way. do not use any adapter plugs.
Check with a qualified electrician if you are in doubt as to whether the outlet
is properly grounded. If the product should electrically malfunction or break down,
grounding provides a low resistance path to carry electricity away from the user.
2.
3.
double insulated products are equipped with a polarized plug (one blade is
wider than the other). This plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician to install a polarized outlet. do not change
the plug in any way. Double insulation
eliminates the need for the three wire
grounded power cord and grounded power supply system.
Avoid body contact with grounded surfaces such as pipes, radiators, ranges,
and refrigerators. There is an increased risk of electric shock if your body is
grounded.
4.
5.
do not expose the AC/dC Adapter of this product to rain or wet conditions.
Water entering the Adapter will increase the risk of electric shock.
do not abuse the Power Cord. Never use the Power Cord to carry this prod-
uct or pull the Plug from an outlet. keep the Power Cord away from heat, oil,
sharp edges, or moving parts. Replace damaged Power Cords immediately.
Damaged Power Cords increase the risk of electric shock.
6.
1.
When operating a power tool outside, use an outdoor extension cord marked
“W-A” or “W”. These extension cords are rated for outdoor use, and reduce the
risk of electric shock.
PERsONAl sAFETy
stay alert. Watch what you are doing, and use common sense when operat-
ing this product. do not use this product while tired or under the influence of
drugs, alcohol, or medication. A moment of inattention while operating electrically
powered products may result in serious personal injury.
2.
3.
do not overreach. keep proper footing and balance at all times. Proper footing
and balance enables better control of the power tool in unexpected situations.
Use safety equipment. Wear ANsI approved safety eye goggles when assem-
bling this product.
PROdUCT UsE ANd CARE
1.
do not force this product. Use the correct product for your application. The
correct product will do the job better and safer at the rate for which it is designed.
Do not force this product and do not use this product for a purpose for which it is
not intended.
SKU 95781
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
3.
do not use if Power switch of theTimer does not turn it on or off. Any product
that cannot be controlled with Power Switch is dangerous and must be replaced.
disconnect the Power Cord Plug from the power source before making any
adjustments, changing accessories, or storing the tool. Such preventive safety
measures reduce the risk of starting the tool accidentally. Always unplug this
prouduct from its electrical outlet before performing any inspection, mainte-
nance, or cleaning procedures.
4.
5.
store idle electrically powered products out of reach of children and other un-
trained persons. Such products are dangerous in the hands of untrained users.
Maintain this product with care. keep this product clean. Properly maintained
products are less likely to malfunction and are easier to control. Do not use dam-
aged products. Tag damaged products “Do not use” until repaired.
6.
7.
Check for misalignment or binding of moving parts, breakage of parts, and
any other condition that may affect this product’s operation. If damaged,
have the product serviced before using. Many accidents are caused by poorly
maintained products.
Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one product may become hazardous
when used on another product.
sERVICE
1.
2.
Product service must be performed only by qualified repair personnel. Service
or maintenance performed by unqualified personnel could result in a risk of injury.
When servicing a product, use only identical replacement parts. Follow
instructions in the “Inspection, Maintenance, And Cleaning” section of this
manual. Use of unauthorized parts or failure to follow maintenance instructions
may create a risk of electric shock or injury.
sPECIFIC sAFETy RUlEs
1.
2.
3.
4.
Maintain labels and nameplates on this product. These carry important informa-
tion. If unreadable or missing, contact Harbor Freight Tools for a replacement.
Maintain a safe environment. Make sure there is adequate surrounding space.
Do not use this product in a damp or wet location.
The AC/dC Adapter must only be plugged into a 120 volt, grounded, electrical
outlet INdOORs. Keep the Adapter dry at all times.
keep product out of reach of children and in a location that will not cause a
tripping hazard.
SKU 95781
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
People with pacemakers should consult their physician(s) before use. Elec-
tromagnetic fields in close proximity to a heart pacemaker could cause pacemaker
interference or pacemaker failure.
gROUNdINg
WARNINg!
Improperly connecting the grounding wire can result in the risk of electric shock.
Check with a qualified electrician if you are in doubt as to whether the outlet is
properly grounded. do not modify the power cord plug provided with this prod-
uct. Never remove the grounding prong from the plug. do not use this product
if the power cord or plug is damaged. If damaged, have it repaired by a service
facility before use. If the plug will not fit the outlet, have a proper outlet installed
by a qualified electrician.
gROUNdEd PROdUCTs: PROdUCTs WITH THREE PRONg PlUgs
1.
Products marked with “Grounding Required” have a three wire cord and three
prong grounding plug. The plug must be connected to a properly grounded outlet.
If the tool should electrically malfunction or break down, grounding provides a low
resistance path to carry electricity away from the user, reducing the risk of electric
shock. (see 3-Prong Plug and Outlet.)
2.
3.
The grounding prong in the plug is connected through the green wire inside the
cord to the grounding system in the tool. The green wire in the cord must be the
only wire connected to the tool’s grounding system and must never be attached to
an electrically “live” terminal. (see 3-Prong Plug and Outlet.)
Your product must be plugged into an appropriate outlet, properly installed and
grounded in accordance with all codes and ordinances. The plug and outlet should
look like those in the following illustration. (see 3-Prong Plug and Outlet.)
3-Prong Plug and Outlet
Outlets for 2-Prong Plug
SKU 95781
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
dOUblE INsUlATEd PROdUCTs:
PROdUCTs WITH TWO PRONg PlUgs
1.
2.
Products marked “Double Insulated” do not require grounding. They have a special
double insulation system which satisfies OSHA requirements and complies with the
applicable standards of Underwriters Laboratories, Inc., the Canadian Standard
Association, and the National Electrical Code. (see Outlets for 2-Prong Plug.)
Double insulated products may be used in either of the 120 volt outlets shown in
the preceding illustration. (see Outlets for 2-Prong Plug.)
ExTENsION CORds
1.
2.
Grounded products require a three wire extension cord. Double Insulated tools
can use either a two or three wire extension cord.
As the distance from the supply outlet increases, you must use a heavier gauge
extension cord. Using extension cords with inadequately sized wire causes a seri-
ous drop in voltage, resulting in loss of power and possible product damage.
(see Table A.)
3.
The smaller the gauge number of the wire, the greater the capacity of the cord. For
example, a 14 gauge cord can carry a higher current than a 16 gauge cord.
(see Table A.)
4.
5.
When using more than one extension cord to make up the total length, make sure
each cord contains at least the minimum wire size required. (see Table A.)
If you are using one extension cord for more than one product, add the nameplate
amperes and use the sum to determine the required minimum cord size.
(see Table A.)
6.
7.
If you are using an extension cord outdoors, make sure it is marked with the suffix
“W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.
Make sure your extension cord is properly wired and in good electrical condition.
Always replace a damaged extension cord or have it repaired by a qualified electri-
cian before using it.
8.
Protect your extension cords from sharp objects, excessive heat, and damp or wet
areas.
SKU 95781
For technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
RECOMMENdEd MINIMUM WIRE gAUgE FOR ExTENsION CORds*
(120 OR 240 VOlT)
NAMEPlATE
AMPEREs
(at full load)
ExTENsION CORd lENgTH
25 Feet
50 Feet
75 Feet 100 Feet 150 Feet
0 – 2.0
2.1 – 3.4
18
18
18
18
18
14
12
18
18
18
16
14
12
10
18
18
16
14
12
10
-
18
16
14
12
10
-
16
14
12
12
-
3.5 – 5.0
5.1 – 7.0
7.1 – 12.0
12.1 – 16.0
16.1 – 20.0
-
-
-
* based on limiting the line voltage drop to five volts at 150% of the rated amperes.
TAblE A
syMbOlOgy
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
Volts Alternating Current
V~
A
Amperes
No Load Revolutions per Minute (RPM)
n xxxx/min.
0
UNPACkINg
When unpacking, check to make sure that the item is intact and undamaged. If any
parts are missing or broken, please call Harbor Freight Tools at the number shown on the
cover of this manual as soon as possible.
AssEMbly INsTRUCTIONs
Note: For additional information regarding the parts listed in the following pages, refer to
the Assembly Diagram near the end of this manual.
SKU 95781
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
1.
2.
WARNINg! Make sure the Power Switch of the Timer is in its “OFF” position
and that the PetWater Fountain is unplugged from its electrical outlet before making
any adjustments to the unit.
Insert the Pump (11) into the Base (1). Fit the Clear Tube (12) into the holding slot
in the Base. Then, place the Pump’s Power Cord in the wire holders along the side
of the Base. (see Figure A.)
CLEAR TUBE (12)
PUMP (11)
CLEAR TUBE (12)
PUMP POWER CORD
FIgURE b
FIgURE A
3.
Make sure all Tubes are properly connected. Remove any sharp bends or kinks in
the Clear Tube (12) or water flow could be reduced. (see Figure b.)
FILTER (3)
FIgURE C
4.
5.
Align the Filter (3) into the corner slots of the Base (1) and press the Filter down
into the water chamber. Use the correct slot, and do not use excessive force.
(see Figure C.)
Feed the Power Cord of the Pump (11) through the square hole in the back of the
Water Tank Stand (16). Make sure the Power Cord is secured by the wire holders
on the side of the Base (1). (see Figure d, next page.)
SKU 95781
For technical questions, please call 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
WATER TANK STAND (16)
BASE (1)
WATER TANK STAND (16)
FIgURE d
FIgURE E
6.
Carefully slide the Water Tank Stand (16) into the Base (1) while pulling the
Power Cord of the Pump (11) out the back of the Water Tank Stand. Make sure all
of the Power Cord comes out the back. (see Figure E.)
WATER TANK CAP (6)
WATER OUTLET (8)
WATER TANK GASKET (5)
WATER TANK
FIgURE F
FIgURE g
7.
8.
Fill the Water Tank (4) with clean, cool water. Make sure the Water Tank Gasket
(5) is properly seated in the Water Tank Cap (6). Then, screw the Water Tank Cap
onto the Water Tank. (see Figure F.)
Turn the Water Tank (4) upside down. With the black Water Outlet (8) on the Water
Tank pointing to the hole in the Water Tank Stand (16), insert the Water Tank into
the Water Tank Stand. (see Figure g.)
SKU 95781
For technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
AC/DC ADAPTER (9)
MUSHROOM HEAD (2)
MUSHROOM STAND (17)
TIMER UNIT (10)
FIgURE I
FIgURE H
9.
Insert the Mushroom Head (2) onto the Mushroom Stand (17).
(see Figure H.)
10.
Connect the AC/DC Adapter (9) to the Timer Unit (10). Then connect the Timer
Unit to the Power Cord of the Water Pump (11). NOTE: Should you not want to
use the Timer Unit, you can remove it and connect the AC/DC Adapter directly to
the Power Cord of the Water Pump. (see Figure I.)
OPERATINg INsTRUCTIONs
1.
2.
Plug the AC/DC Adapter (9) into the nearest 120 volt, grounded electrical outlet.
The Water Pump (11) should start and water will come out from the nozzle or
from the Mushroom Head (2). (see Figures H and I.)
Check the position of the Switch on the Timer Unit (10). Slide the Switch to 30
Min. to turn the Water Pump (11) ON for 30 minutes and OFF for 30 minutes
repeatedly. Or slide the Switch to 60 Min. to turn the Water Pump ON for 60 min-
utes and OFF for 60 minutes repeatedly. (see Figure I.)
3.
4.
NOTE: Slide the Switch on the Timer Unit (10) to the OFF position to turn off the
Water Pump (11). It is recommended to unplug the AC/DC Adapter (9) if the Pet
Water Fountain will not be used for long periods of time. (see Figure I.)
Water flow speed can be adjusted by sliding the small window located on the
Water Pump’s (11) side next to where the water flows out.
5.
6.
SKU 95781
For technical questions, please call 1-800-444-3353.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
(14-1) Fountain Nozzle
(14) Spray Nozzle
(14-2) Spray Cover
Figure j
7.
IMPORTANT: Dogs and larger pets will probably prefer that you remove the
Mushroom Head (2) and Mushroom Stand (17) and replace them with the includ-
ed Spray Nozzle (14) or Fountain Nozzle (14-1). (See Figures H and J.)
6.
To install the Spray Nozzle (14) or Fountain Nozzle (14-1):
a. �e�o�e the ushroo� �eaꢀ (�) anꢀ ushroo� Stanꢀ (1�).
(See Figure H.)
b. �ꢏꢊꢓꢒꢓꢇꢏ ꢇꢐꢏ �ꢋꢏꢓꢒ �ꢌbꢏ ꢀꢁꢂ bꢃ ꢌꢉꢊꢋꢌꢍꢍꢈꢉꢍ ꢇꢐꢏ ꢄꢅ ꢑꢏꢍꢒꢏꢏ ꢆꢇꢇꢈꢉꢍ ꢇꢐꢓꢇ ꢊꢋꢌꢍꢎ
into the botto� of the ushroo� Stanꢀ (1�). (See Figures A, B, and H.)
c. Separate the t o �lear Tubes (1�) at the blacꢁ union. Then re�o�e the blacꢁ
union anꢀ the short length of the �lear Tube (1�) (See Figures A and B.)
ꢀ. To use the Spray Nozzle (14)ꢂ slip the �ale enꢀ of it (14) into the longest
length of �lear Tube (1�) that connects to the Water Pu�p (11).
To use it ith the Fountain function (14-1)ꢂ re�o�e the spray co�er (14-�).
(See Figures A, B and J.)
ꢏ. �ꢌꢒꢉ ꢕꢉ ꢇꢐꢏ �ꢓꢇꢏꢒ �ꢌ�ꢊ ꢀꢁꢁ ꢓꢉꢑ ꢓꢑꢖꢌꢎꢇ ꢇꢐꢏ ꢗꢓꢇꢏꢒ ꢔꢕꢗ bꢃ ꢒꢓꢈꢎꢈꢉꢍ ꢕꢒ ꢋꢕꢗꢏꢒꢈꢉꢍ
the Blacꢁ Le�er (13)ꢂ hich the �lear Tube passes through. (See Assembly
diagram.)
INsPECTION, MAINTENANCE, ANd ClEANINg
1.
2.
WARNINg! Make sure the Power Switch of the AC/DC Adapter (9) is in its
“OFF”position and that the PetWater Fountain is unplugged from its electrical outlet
before performing any inspection, maintenance, or cleaning procedures.
bEFORE EACH UsE, inspect the general condition of the Pet Water Fountain.
Check for misalignment or binding of moving parts, cracked or broken parts, dam-
aged electrical wiring, and any other condition that may affect its safe operation. If
abnormal noise or vibration occurs, have the problem corrected before further use.
do not use damaged equipment.
REV 07j
SKU 95781
For technical questions, please call 1-800-444-3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE CHART
before
Use
After
Use
Every 6
Months
Maintenance Type
Weekly Monthly
yearly
Inspect tool for damage
(See Step #2, previous page.)
x
Wipe off with clean, moist
cloth
x
x
x
x
x
x
Empty old water
Refill with clean, cool water
Clean Water Filter
x
x
TROUblEsHOOTINg
Problem
Possible Causes
Probable solutions
Fountain will not start 1. No power at outlet.
1. Check power at outlet.
2. Cord not connected.
2. Check that cord is plugged in.
Improper water flow
Clogged water filter
1. Sharp bend(s) or kink(s) in Clear
Tubes.
1. Remove any bends or kinks in
Clear Tubes.
2. Improper adjustment of Black Lever. 2. Slide Black Lever up or down until
proper water flow is achieved.
1. Dirt or debris has clogged filter.
2. Animal hair has clogged filter.
1. Clean filter.
2. Keep fountain clear of debris to
prevent clogging.
PlEAsE REAd THE FOllOWINg CAREFUlly
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEM-
BLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER
OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER
THAT HE OR SHE IS qUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR
SHE IS qUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR ExPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS
TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS
OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 95781
For technical questions, please call 1-800-444-3353.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTs lIsT ANd dIAgRAM
Part
description
Q’ty
Part
10
description
Timer Unit
Q’ty
1
2
3
4
5
6
7
8
9
Base
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
Mushroom Head
Water Filter
11
Water Pump
Clear Tube
12
Water Tank
13
Black Lever
Spray Nozzle
Water Tank Gasket
Water Tank Cap
Water Outlet Gasket
Water Outlet
14
14 - 1 Fountain Nozzle
14 - 2 Spray Cover
16
17
Water Tank Stand
Mushroom Stand
AC/DC Adapter
Record Product’s serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available
individually as replacement parts.
REV 07j
SKU 95781
For technical questions, please call 1-800-444-3353.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
AssEMbly dIAgRAM
4
5
11
6
9
7
8
10
3
2
17
16
1
14, 15
12
13
SKU 95781
For technical questions, please call 1-800-444-3353.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
|