MOTORCYCLE LIFT
AIR OPERATED - 1,200 LB. CAPACITY
Model 94813
ASSEMBLY AND OPERATING INSTRUCTIONS
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
©
®
Copyright 2006 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of Harbor
Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improve-
ments, actual product may differ slightly from the product described herein. Tools required for assembly
and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 10h; 11a
Download from Www.Somanuals.com. All Manuals Search And Download.
PERSONAL SAFETY
1.
2.
Stay alert. Watch what you are doing, and use common sense during use. Do
not use the Motorcycle Lift while tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating equipment may result in
serious personal injury.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep
your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or
long hair can be caught in moving parts.
3.
4.
Do not overreach. Keep proper footing and balance at all times. Proper footing
and balance enables better control in unexpected situations.
Always wear eye protection. Wear ANSI-approved safety impact eye glasses
when using this product.
TOOL USE AND CARE
1.
2.
Store idle tools and equipment out of reach of children and other untrained
people. Tools and equipment are dangerous in the hands of untrained users.
Maintain the Motorcycle Lift with care. Keep this product clean. A properly
maintained tool is easier to control. Do not use damaged tools and equipment. Tag
damaged tools and equipment “Do not use” until repaired.
3.
4.
Check for misalignment or binding of moving parts, loose or broken parts,
and any other condition that may affect the Motorcycle Lift’s operation.
If damaged, have the tool serviced before using. Many accidents are caused by
poorly maintained tools and equipment.
Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one product may become hazardous
when used on another product.
SERVICE
1.
2.
Tool service must be performed only by qualified service technician. Service
or maintenance performed by unqualified personnel could result in a risk of injury.
When servicing the Motorcycle Lift, use only identical replacement parts.
Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this
manual. Use of unauthorized parts or failure to follow maintenance instructions
may create a risk of injury.
SKU 94813
For technical questions, please call 1-800-444-3353
PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFIC SAFETY RULES
1.
2.
Maintain labels and nameplates on the Motorcycle Lift. These carry important
information. If unreadable or missing, contact Harbor Freight Tools for a replace-
ment.
Use the right product for the job. There are certain applications for which this
product was designed. Do not use this product for a purpose for which it was not
intended.
3.
4.
Industrial applications must follow OSHA requirements.
Prior to using this product, make sure to read and understand all
instructions and safety precautions as outlined in the motorcycle
manufacturer’s manual.
5.
WARNING! Do not exceed the 1,200 pound maximum lifting capacity of this
tool. Exceeding the maximum lifting capacity could cause personal injury and/or
property damage. Beware of dynamic loading! Suddenly dropping a load onto this
product may create, for a brief instant, an excess load which may result in damage
to the product and/or personal injury.
6.
7.
Use the Motorcycle Lift only on a flat, level, solid surface capable of support-
ing the weight of the Lift and the weight of the object being lifted.
Make sure any load being supported by this Motorcycle Lift is well balanced
and centered over the Lift. Unbalanced loads may cause the lift to tip over, po-
tentially causing serious personal injury and/or property damage.
8.
Stay clear of the Motorcycle Lift when in motion. Never go under an object be-
ing supported by the Lift unless the Safety Bar (11) is in place. Always use the
Safety Bar to lock the Lift when in its up position.
9.
This Motorcycle Lift is not designed to be used for aircraft purposes.
10.
Always make sure the object being lifted is properly and safely secured to the
Motorcycle Lift prior to raising the object.
11.
WARNING! Do not operate a motorcycle in a closed area or a poorly ventilated
area. When running, the engine of a motorcycle produces carbon monoxide, a
colorless, odorless, toxic fume that, when inhaled, can cause serious personal
injury or death.
12.
13.
Always monitor the object being lifted so it does not rock back and forth.
Never exceed the maximum working air pressure of 125 PSI for this Motorcycle
Lift. Doing so may cause personal injury and/or property damage.
SKU 94813
For technical questions, please call 1-800-444-3353
PAGE 4
Download from Www.Somanuals.com. All Manuals Search And Download.
14.
15.
Use compressed air only. Use clean, dry, regulated, compressed air. Never use
oxygen, carbon dioxide, combustible gases, or any other bottled gas as a power
source for this tool.
WARNING! The warnings and cautions discussed in this manual cannot cover all
possible conditions and situations that may occur. It must be understood by the
operator that common sense and caution are factors which cannot be built into this
product, but must be supplied by the operator.
SAVE THESE INSTRUCTIONS
PRE-ASSEMBLY INSTRUCTIONS
NOTE:
For further references to the parts mentioned in the following pages,
see the Assembly Diagrams on pages 13 and 14 of this manual.
To Move The Motorcycle Lift To A Proper Location:
1.
2.
AminimumoftwoadultsarenormallyrequiredtosetupandoperatetheMotorcycleLift.
Prepare for assembly by having a clean, spacious, well lit location. It is recom-
mended to assemble the Motorcycle Lift on the floor.
PLATFORM
(8)
DOLLY HANDLE
(1D)
HOOK
LIFT DOLLY
(58)
FOOT AIR VALVE
(48)
FIGURE A
AIR HOSE CONNECTOR (49)
3.
Once the Motorcycle Lift is unpacked, use the accessory Lift Dolly (58) to move
the Lift to the desired assembly location. To do so, insert the Hook on the Lift’s
bottom chassis into the hole at the bottom of the Lift Dolly. Press down on the
Dolly Handle (1D) to slightly raise the end of the Motorcycle Lift. Then, move the
Lift to the desired assembly location. (See Figure A.)
SKU 94813
For technical questions, please call 1-800-444-3353
PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
REGULATOR
TO
QUICK COUPLER (49)
OF
MOTORCYCLE LIFT
FILTER
OILER
FIGURE B
To Connect The Motorcycle Lift To An Air Compressor:
For best service, you should incorporate an oiler, regulator, and in-line filter, as
above. Hoses, couplers, oilers, regulators, and filters are all available at Harbor
Freight Tools.
Note: If an automatic oiler is not used, put 3-5 drops of pneumatic Tool Oil (not included) in
the Motorcycle Lift’s Air Hose Connector (49) before each use. (See Figure A.)
SKU 94813
For technical questions, please call 1-800-444-3353
PAGE 6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTIONS
SAFETY BAR HANDLE
(14)
SAFETY BAR
(11)
LIFTING ARM
TEETH
(24)
FIGURE C
WARNING! As an additional safety precaution, ALWAYS lower the Safety Bar
(11) completely and make sure it rests between the teeth of the Lifting Arms
(24) when the Motorcycle Lift is in its raised position. To do so, raise the Mo-
torcycle Lift to slightly above the desired height. Lower the Safety Bar and, while
holding the Safety Bar in its lowered position, slowly lower the Motorcycle Lift until
the Safety Bar is firmly settled between the teeth of the Lifting Arms.
(See Figure C.)
To Attach The Tire Stop Plate:
1.
Step on and hold down the right side of the Foot Air Valve (48) until the Platform (8)
of the Motorcycle Lift reaches its maximum height. Then, lower and lock the Safety
Bar (11) in position. (See Figures A and C.)
SKU 94813
For technical questions, please call 1-800-444-3353
PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
BOLT
(2)
STOP PLATE
(1)
WASHER
(29)
NUT
(27)
FIGURE D
2.
Align the two mounting slots in the Stop Plate (1) with the two mounting holes located
at the rear of the Platform (8). Then secure the Stop Plate to the Platform, using two
Bolts (2), two Washers (29), and two Nuts (27). NOTE: When adjusting the Stop
Plate forward or backward, make sure to retighten the two Nuts. (See Figure D.)
To Install The Vise Assembly:
VISE ASSEMBLY
(4, 6, 7)
WASHER
(29)
NUT
(27)
FIGURE E
1.
2.
NOTE: Additional mounting holes at the rear of the Platform (8) allow for adjusting
the forward/backward location of the Vise assembly. (See Figure E.)
To install the Vise Assembly (4, 6, 7), align the ten mounting holes at the base of
the Vise Assembly with ten of the mounting holes located at the rear of the Platform
(8). Then secure the Vise assembly to the Platform, using ten Bolts (2), Washers
(29), and Nuts (27). (See Figure E.)
Rev 11a
SKU 94813
For technical questions, please call 1-800-444-3353
PAGE 8
Download from Www.Somanuals.com. All Manuals Search And Download.
To Install The Ramp:
PLATFORM
(8)
RAMP
(10)
FIGURE F
With assistance, lift the Ramp (10) and insert its two prongs into the two mounting
holes located at the front of the Platform. (See Figure F.)
SKU 94813
For technical questions, please call 1-800-444-3353
PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
1.
WARNING! Do not exceed the maximum lifting capacity of this tool (1,200
pounds). Exceeding the maximum lifting capacities could cause personal injury
and/or property damage.
2.
3.
Make sure the Platform (8) is fully collapsed to the floor. Also, make sure the Remov-
able Plate (9) is properly positioned over the inspection hole of the Platform (8).
With assistance, roll the motorcycle up the Ramp (10) and onto the Platform (8)
until its front wheel contacts the Stop Plate (1). Then, kick the center stand of the
motorcycle down to stabilize it on the Lift.
4.
5.
Adjust the Vise assembly (4, 6, 7), and clamp the bottom of the front motorcycle
wheel into the Vise assembly. Then, resecure the Vise assembly to the Platform
(8). You should also stabilize the motorcycle using tie-down straps (not included) on
each side of the motorcycle with one end of the straps tied to the motorcycle and
the other end of the straps tied to the Platform (8).
Connect the air compressor’s hose to the Foot Valve Air. Then turn on the air
compressor and set its regulator to 110 to 125 PSI. Do not exceed 125 PSI. (See
Figure B.) Make sure the Foot Air Valve (48) is located on the floor surface and
safely away from the Motorcycle Lift so as to avoid damaging the Foot Air Valve.
(See Figure A.) Step on and hold down the right side of the Foot Air Valve (48) until
the Platform (8) of the Motorcycle Lift reaches its maximum height. Then step on
and hold the left side of the Foot Air Valve until the Platform is fully collapsed to the
floor. Repeat this procedure several times to ensure the Motorcycle Lift is operating
properly. (See Figure A.)
6.
7.
8.
9.
When the Platform (8) has been raised to the working height, lower the Safety Bar
(11) completely to prevent the Motorcycle Lift from accidentally lowering.
When work on the motorcycle is completed, check under the Motorcycle Lift to make
sure there are no tools, motorcycle parts, etc. and that it is safe to lower the Lift.
Swing the Safety Bar (11) aside. Then step on and hold down the left side of the
Foot Air Valve (48) to slowly lower the Platform (8) to the floor.
With assistance, remove the tie-down straps from the motorcycle. Loosen the Vise
assembly (4, 6, 7). Kick the center stand of the motorcycle up. Then, slowly back
the motorcycle completely off the Motorcycle Lift.
10.
11.
Turn off the air compressor. Step on and hold down the left side of the FootAir Valve
(48) to release any remaining compressed air in the system. Then, disconnect the
compressor’s air hose from the Foot Air Valve.
Make sure to store the Motorcycle Lift in a clean, dry, safe location out of reach of
children and other unauthorized people.
SKU 94813
For technical questions, please call 1-800-444-3353
PAGE 10
Download from Www.Somanuals.com. All Manuals Search And Download.
INSPECTION, MAINTENANCE, AND CLEANING
1.
Before each use: Inspect the general condition of the Motorcycle Lift. Check for
cracked, worn or damaged parts, loose or missing parts, low or no hydraulic oil, and
any other condition that may affect the tool’s safe operation. If a problem occurs,
have the problem corrected before further use.
Do not use damaged equipment.
2.
3.
4.
To clean: Use a damp cloth and a mild detergent. Do not use solvents or other
flammable agents.
When storing: Keep the Motorcycle Lift and its accessories in a clean, dry, safe
location out of reach of children and other unauthorized people.
CAUTION! All maintenance, service, and repairs not discussed in this manual
should only be performed by a qualified service technician.
TROUBLESHOOTING
Problem
Possible Solution
1. Make sure the unit’s 1,200 pound lifting capacity is not being
exceeded.
Motorcycle Lift “fades”, allowing a
load to slowly lower on its own.
2. Check all air connections for leaks.
3. The Air Foot Valve (48) may be leaking. A technician should
investigate and replace o-rings or entire unit as necessary.
4. If none of the above solutions correct the problem, have a
qualified service technician examine the unit. Do not use the
unit until completely repaired.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND
ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE
MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY
OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY
CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER AS-
SUMES ALL RISKS AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGI-
NAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 94813
For technical questions, please call 1-800-444-3353
PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
MAIN PARTS LIST
Part
Description
Qty.
Part
Description
Qty.
1
Stop Plate
1
12
1
47
48*
49
51
52
53
54
56
57
58*
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
Air Hose
1
1
1
2
1
2
4
2
2
1
4
2
2
1
1
1
4
4
2
1
2
1
1
1
1
1
1
4
2
Bolt (M10 x 25)
Adjustable Shelf M10 x 25
Bolt (M8 x 20)
Moveable Vise Assy.
Stationary Vise Assy.
Platform
Foot Operated Air Valve
Air Hose Connector
Wheel
4
5
4
6
1
Connection
7
1
Bolt (M10 x 45)
Cam Bearing Spacer
Roller
8
1
9
Removable Plate
Ramp
1
10
11
1
Roller
Safety Bar
1
Lift Dolly
12
13
14
15
16
17
18
19
22
23
24
25
26
27
28
29
30a
31a
33a
34a
35
36
37a
38a
39a
40a
41a
43a
45a
46a
Clevis Pin
2
Grease fitting
Cotter Pin
R-Pin
2
Safety Bar Handle
Bolt (M16 x 130)
Washer (#16)
Lock Nut (M16)
Lifting Arm
1
Air Pump Washer
Bolt (M12 x 25)
Washer (#12)
O-Ring
2
6
4
1
Retaining Ring
Cam Bearing Spacer
Retaining Ring
Split Washer
O-Ring
Bolt (M16 x 80)
Retaining Ring
Frame/Cylinder Pivot Shaft
Lifting Arm
2
4
1
1
Cylinder End Plate
Lock Nut (M10)
Nut (M10)
1
Connector
2
Connecting Block
Filter Base
16
20
20
4
Lock Washer (#10)
Washer (#10)
Stay Bolt
Filter
O-Ring
Connecting Bolt
Mut (M10)
Cylinder
1
Piston
1
O-Ring
1
O-Ring
1
Seal Ring
1
Press Ring
1
Retaining Ring
Piston Rod
2
1
O-Ring
2
Shaft Bushing
O-Ring
1
1
Front Cover
Nut
1
1
* See the additional Parts List and Assembly Diagram on page 14.
NOTE:
Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
REV 10h
SKU 94813
For technical questions, please call 1-800-444-3353
PAGE 12
Download from Www.Somanuals.com. All Manuals Search And Download.
MAIN ASSEMBLY DIAGRAM
NOTE:
Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
REV 10h
SKU 94813
For technical questions, please call 1-800-444-3353
PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST AND ASSEMBLY DIAGRAM - LIFT DOLLY (58)
Part
1D
2D
3D
4D
5D
6D
7D
Description
Dolly Handle
Bolt
Qty
1
2
Pin
2
Washer
Nut
2
2
Wheel
2
Dolly Set
1
NOTE:
Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
PARTS LIST AND ASSEMBLY DIAGRAM - FOOT AIR VALVE (48)
Part
1V
Description
Foot Pedal
Retaining Ring
Washer
Qty
1
2V
1
3V
2
4V
O-Ring
1
5V
Valve Rod
O-Ring
1
6V
2
7V
Seal
1
8V
Retaining Ring
Lock Nut
1
9V
1
10V
11V
12V
Valve Body
Bolt
1
1
Quick Coupler
1
NOTE:
Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
REV 10h
SKU 94813
For technical questions, please call 1-800-444-3353
PAGE 14
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED 90 DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this product
is free from defects in materials and workmanship for the period of 90 days from the date
of purchase. This warranty does not apply to damage due directly or indirectly, to misuse,
abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity,
improper installation, normal wear and tear, or to lack of maintenance. We shall in no event
be liable for death, injuries to persons or property, or for incidental, contingent, special
or consequential damages arising from the use of our product. Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation
of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the com-
plaint must accompany the merchandise. If our inspection verifies the defect, we will either
repair or replace the product at our election or we may elect to refund the purchase price
if we cannot readily and quickly provide you with a replacement. We will return repaired
products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning
the product.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 94813
For technical questions, please call 1-800-444-3353
PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
|