7” x 10” Precision
Mini Lathe
Model 93212
set uP and oPerating instructions
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
saVe this ManuaL.
©
®
Copyright 2006 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Manual revised 10e
Download from Www.Somanuals.com. All Manuals Search And Download.
notice is used to
address practices not
saVe this ManuaL
Keep this manual for the safety warnings
and precautions, assembly, operating,
inspection, maintenance and cleaning
procedures. Write the product’s serial number
in the back of the manual near the assembly
diagram (or month and year of purchase if
product has no number). Keep this manual
and the receipt in a safe and dry place for
future reference.
related to personal injury.
caution, without the
safety alert symbol, is
used to address practices not
related to personal injury.
general tool safety Warnings
Warning read all safety warnings
and instructions. Failure to follow the
warnings and instructions may result
in electric shock, fire and/or serious
injury.
iMPortant saFetY
inForMation
in this manual, on the labeling, and
all other information provided with
this product:
save all warnings and instructions
for future reference.
1. KEEP GUARDS IN PLACE and in
working order.
this is the safety alert
symbol. it is used to alert
you to potential personal
injury hazards. obey all
safety messages that follow
this symbol to avoid possible
injury or death.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking to
see that keys and adjusting wrenches
are removed from tool before turning it
on.
3. KEEP WORK AREA CLEAN. Cluttered
areas and benches invite accidents.
danger indicates a
hazardous situation
which, if not avoided, will result
in death or serious injury.
4. DON’T USE IN DANGEROUS
ENVIRONMENT. Don’t use power tools
in damp or wet locations, or expose them
to rain. Keep work area well lighted.
Warning indicates a
hazardous situation
which, if not avoided, could
result in death or serious injury.
5. KEEP CHILDREN AWAY. All visitors
should be kept safe distance from work
area.
6. MAKE WORKSHOP KID PROOF
with padlocks, master switches, or by
removing starter keys.
caution, used with
the safety alert
symbol, indicates a hazardous
situation which, if not avoided,
could result in minor or moderate
injury.
7. DON’T FORCE TOOL. It will do the job
better and safer at the rate for which it
was designed.
SKU 93212
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
8. USE RIGHT TOOL. Don’t force tool or
attachment to do a job for which it was
not designed.
13. DON’T OVERREACH. Keep proper
footing and balance at all times.
14. MAINTAIN TOOLS WITH CARE. Keep
tools sharp and clean for best and safest
performance. Follow instructions for
recoMMended MiniMuM Wire
gauge For extension cords
(120 VoLt)
lubricating and changing accessories.
extension cord
naMePLate
aMPeres
(at full load)
15. DISCONNECT TOOLS before servicing;
when changing accessories, such as
blades, bits, cutters, and the like.
Length
25’
50’ 100’ 150’
0 – 6
18
18
16
14
16
16
16
12
16
14
14
14
12
12
6.1 – 10
16. REDUCE THE RISK OF
UNINTENTIONAL STARTING. Make
sure switch is in off position before
plugging in.
10.1 – 12
12.1 – 16
taBLe a
do not use.
17. USE RECOMMENDED ACCESSORIES.
Consult the owner’s manual for
9. USE PROPER EXTENSION CORD.
Make sure your extension cord is in good
condition. When using an extension
cord, be sure to use one heavy enough
to carry the current your product will
draw. An undersized cord will cause a
drop in line voltage resulting in loss of
power and overheating. Table A shows
the correct size to use depending on
cord length and nameplate ampere
rating. If in doubt, use the next heavier
gauge. The smaller the gauge number,
the heavier the cord.
recommended accessories. The use of
improper accessories may cause risk of
injury to persons.
18. NEVER STAND ON TOOL. Serious
injury could occur if the tool is tipped
or if the cutting tool is unintentionally
contacted.
19. CHECK DAMAGED PARTS. Before
further use of the tool, a guard or other
part that is damaged should be carefully
checked to determine that it will operate
properly and perform its intended
10. WEAR PROPER APPAREL. Do not wear
loose clothing, gloves, neckties, rings,
bracelets, or other jewelry which may get
caught in moving parts. Nonslip footwear
is recommended. Wear protective hair
covering to contain long hair.
function – check for alignment of moving
parts, binding of moving parts, breakage
of parts, mounting, and any other
conditions that may affect its operation.
A guard or other part that is damaged
should be properly repaired or replaced.
11. ALWAYS USE SAFETY GLASSES. Also
use face or dust mask if cutting operation
is dusty. Everyday eyeglasses only have
impact resistant lenses, they are NOT
safety glasses.
20. NEVER LEAVE TOOL RUNNING
UNATTENDED. TURN POWER OFF.
Don’t leave tool until it comes to a
complete stop.
12. SECURE WORK. Use clamps or a vise
to hold work when practical. It’s safer
than using your hand and it frees both
hands to operate tool.
Page 4
For technical questions, please call 1-800-444-3353.
SKU 93212
Download from Www.Somanuals.com. All Manuals Search And Download.
3-pole receptacles that accept the tool’s
plug.
grounding instructions
to PreVent
eLectric shock
and death FroM incorrect
grounding Wire
6. Repair or replace damaged or worn cord
immediately.
connection
read and FoLLoW these
instructions:
grounding
Pin
110-120 V~ grounded tools: tools
with three Prong Plugs
1. In the event of a malfunction or
breakdown, grounding provides a path
of least resistance for electric current
to reduce the risk of electric shock.
This tool is equipped with an electric
cord having an equipment-grounding
conductor and a grounding plug. The
plug must be plugged into a matching
outlet that is properly installed and
grounded in accordance with all local
codes and ordinances.
125 V~ 3-Prong Plug and outlet
(for up to 125 V~ and up to 15 a)
7. This tool is intended for use on a circuit
that has an outlet that looks like the one
illustrated above in 125 V~ 3-Prong
Plug and outlet. The tool has a
grounding plug that looks like the plug
illustrated above in 125 V~ 3-Prong
Plug and outlet.
8. The outlet must be properly installed and
grounded in accordance with all codes
and ordinances.
2. Do not modify the plug provided – if it will
not fit the outlet, have the proper outlet
installed by a qualified electrician.
9. Do not use an adapter to connect this
tool to a different outlet.
3. Improper connection of the equipment-
grounding conductor can result in a risk
of electric shock. The conductor with
insulation having an outer surface that
is green with or without yellow stripes is
the equipment-grounding conductor. If
repair or replacement of the electric cord
or plug is necessary, do not connect the
equipment-grounding conductor to a live
terminal.
Mini Lathe safety Warnings
1. For Your oWn saFetY, read and
understand this instruction
ManuaL BeFore oPerating
Lathe.
2. Wear ANSI-approved eye protection.
3. Do not wear gloves, necktie, or loose
clothing while operating the Lathe.
4. Check with a qualified electrician or
service personnel if the grounding
instructions are not completely
4. Tie back long hair. Long hair in a ponytail
needs to be secured so there is no risk
of entanglement.
understood, or if in doubt as to whether
the tool is properly grounded.
5. Use only 3-wire extension cords that
have 3-prong grounding plugs and
5. Tighten all locks before operating.
SKU 93212
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
6. do not oPerate With anY
guard disaBLed, daMaged, or
reMoVed. Moving guards must
move freely and close instantly.
carriage will contact the chuck during
operation.
19. Use the appropriate feed and speed
rates for the project.
7. Rotate workpiece by hand before
applying power.
20. Allow the lathe to reach its full speed
before beginning a cut.
8. Rough out workpiece before installing on
faceplate.
21. Only use safety equipment that has been
approved by an appropriate standards
agency. Unapproved safety equipment
may not provide adequate protection.
Eye protection must be ANSI-approved
and breathing protection must be
9. Do not mount split workpiece or one
containing knot.
10. Use lowest speed when starting new
workpiece.
NIOSH-approved for the specific hazards
in the work area.
11. Do not reverse motor direction while the
lathe is in motion.
22. Industrial applications must follow OSHA
guidelines.
12. Do not clear chips by hand or when
lathe is running. Use a brush to sweep
chips away after the tool has come to a
complete stop.
23. Maintain labels and nameplates on
the tool. These carry important safety
information. If unreadable or missing,
contact Harbor Freight Tools for a
replacement.
13. Select the proper tool for the job. Using
the correct tool for the job produces a
better finish and minimizes strain on the
lathe.
24. Avoid unintentional starting. Prepare to
begin work before turning on the tool.
14. The use of accessories or attachments
not recommended by the manufacturer
may result in a risk of injury to persons.
When servicing, use only identical
replacement parts.
25. People with pacemakers should
consult their physician(s) before use.
Electromagnetic fields in close proximity
to heart pacemaker could cause
pacemaker interference or pacemaker
failure.
15. Support pieces extending beyond the
headstock so they cannot cause injury to
the operator, bystanders or lathe. Turn
supported long stock at slower RPM’s.
26. WARNING: Some dust created by power
sanding, sawing, grinding, drilling, and
other construction activities, contains
chemicals known [to the State of
California] to cause cancer, birth defects
or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints
16. Use a chuck cradle or piece of plywood
to protect the precision ground ways and
your hands when servicing chucks.
17. Check that the workpiece, tool, tool post,
chuck and saddle all have adequate
clearance before starting the lathe.
• Crystalline silica from bricks and
cement or other masonry products
• Arsenic and chromium from chemically
treated lumber
18. Check that no part of the tool, tool
holder, compound slide, cross slide, or
Page 6
For technical questions, please call 1-800-444-3353.
SKU 93212
Download from Www.Somanuals.com. All Manuals Search And Download.
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to
these chemicals: work in a well ventilated
area, and work with approved safety
equipment, such as those dust masks
that are specially designed to filter out
microscopic particles. (California Health
& Safety Code § 25249.5, et seq.)
or physical symptoms related to vibration
(such as tingling, numbness, and white
or blue fingers), seek medical advice as
soon as possible.
2. Do not smoke during use. Nicotine
reduces the blood supply to the hands
and fingers, increasing the risk of
vibration-related injury.
3. Wear suitable gloves to reduce the
vibration effects on the user.
27. WARNING: Handling the cord on this
product will expose you to lead, a
chemical known to the State of California
to cause cancer, and birth defects or
other reproductive harm. Wash hands
after handling. (California Health &
Safety Code § 25249.5, et seq.)
4. Use tools with the lowest vibration when
there is a choice between different
processes.
5. Include vibration-free periods each day
of work.
28. The warnings, precautions, and
instructions discussed in this instruction
manual cannot cover all possible
conditions and situations that may occur.
It must be understood by the operator
that common sense and caution are
factors which cannot be built into this
product, but must be supplied by the
operator.
6. When cutting do not apply too much
pressure to the workpiece. Let the tool
do the work.
7. To reduce vibration, maintain the tool
as explained in this manual. If any
abnormal vibration occurs, stop use
immediately.
saVe these
Vibration safety
instructions.
This tool vibrates during use. Repeated
or long-term exposure to vibration may
cause temporary or permanent physical
injury, particularly to the hands, arms
and shoulders. To reduce the risk of
vibration-related injury:
1. Anyone using vibrating tools regularly
or for an extended period should first
be examined by a doctor and then have
regular medical check-ups to ensure
medical problems are not being caused
or worsened from use. Pregnant
women or people who have impaired
blood circulation to the hand, past hand
injuries, nervous system disorders,
diabetes, or Raynaud’s Disease should
not use this tool. If you feel any medical
reV 10b
SKU 93212
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Packing List
sPeciFications
Part
#(s)
Motor
120 V~ / 60 Hz / 3/4 HP
description
Main unit
Qty
0 - 1100 RPM (Low)
0 - 2500 RPM (High)
Speed Ranges
1
2
3
4
5
6
1
External Chuck Jaw Set
Chip Tray
3 jaws
166
126
167
314
Fast Acting 4 amp mini
glass (F4AL250VP)
Fuse Type
Belt
1
1
1
Lx136
Pitch: 1.5mm
Teeth: 70
Chuck Key
5 A Fuse
Gear: 30, 35, 40, 40, 45,
50, 55, 57, 60, 65 T
10
gears
157-
165
Drive
Gear and Belt
Swing Over Bed
Dist. Between Centers
Swing Over Cross Slide
Swing Over Saddle
Swing Over Gap
Max. Tool Bit Size
Compound Travel
Carriage Travel
Cross Slide Travel
Work Tolerance
Bed Dimensions
Tailstock Taper
7”
7
8
9
Spanner Wrench: 8-10,
14-17
2
312,
313
10”
wrenches
2-1/8”
Hex Key Wrench Set: 3,
4, 5, 6
4
311
wrenches
4-1/2”
Oil can
1
1
4
4
310
143
125
67
7”
10 MT:2 Live Center
11 Rubber Foot
5/16”
2-3/4”
12
Rubber Foot Mounting
Screw
6-1/2”
2-3/4”
13
Knob
2
1
85
0.005”
14
Manual
317
15-7/8” L x 3-1/4” W
MT#2
18 threads from 12 - 52
TPI
Threads
Through Chuck Capacity
5/8”
chuck dia.
external
Jaws
internal Jaws
(mm)
A - A1
B - B1
C - C1
80
5/64” - 1-1/8” 1” - 2-3/4” 7/8” - 2-1/2”
shipping Bolt Locations
To remove the lathe from the packing
crate, remove both bolts on the crate bottom
as shown above.
Many components need to be installed
before use. it is essentiaL that both
guards (found in separate boxes within the
main box) are installed before connecting
power.
unPacking
When unpacking, make sure that the
item is intact and undamaged. If any parts
are missing or broken, please call Harbor
Freight Tools at 1-800-444-3353 as soon as
possible.
note: Wipe off protective grease from the
lathe before using.
reV 10b, 10e
Page 8
For technical questions, please call 1-800-444-3353.
SKU 93212
Download from Www.Somanuals.com. All Manuals Search And Download.
generaL Mini Lathe coMPonents
note: Refer to the parts list and diagram at the end of this manual for complete part number
listings and locations. See the following page for a description of the major components.
Part
description
Part
description
1
Bed Way
Chuck
126
129
138
143
146
151
153
178
179
180
181
268
302
Chip Tray
Lead Screw
Tailstock
2
33
35
53
H/L Speed Gear Shift Lever
Feed Direction Selector
Gear Drive Cover
Automatic Feed Handle
Tailstock Quill Control Wheel
Feed Control Wheel
Cross Slide Crank
Live Center
Tailstock Quill Fix Holder
Motor Cover
Rear Splash Guard
Power Switch
79
84a
84b
86a
86b
100
Fuse Holder
Compound Rest Crank
Cross Slide
Speed Control Knob
Forward-Off-Reverse Switch
Tailstock Set Screw
Thread Dial Indicator
105/108 Compound Rest (A and B)
112
124
Tool Post
Power Cord
181
179
180
2
112 105 143
146 138
84(a)
178
268
86(b)
1
84(b)
86(a)
100
79 302
129
53
35
153
126
33
151
124
Figure 1
reV 10b
SKU 93212
For technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
PoWer controLs oVerVieW
controls on the Front of the Lathe
controls on the Back of the Lathe
Forward-OFF-Reverse Switch (181)
Feed Direction Selector (35)
H/L Gear Shift Lever (33)
Power Switch (178)
Speed Control Knob (180)
Figure 2
Power switch (178)
Figure 3
Turns on and off power to the motor.
When the Power Switch is lit, the motor
is on.
Feed direction selector (35)
Changes the Lead Screw (129) rotation
from Forward (toward the Chuck) to
Neutral (no rotation), to Reverse (away
from the Chuck).
Forward-oFF-reverse switch (181)
Changes the Spindle (3) (Chuck (2))
rotation from Forward (clockwise),
to OFF (no rotation), to Reverse
(counterclockwise).
do not change the Feed direction
selector while the Lathe is running.
h/L gear shift Lever (33)
do not change the Forward-oFF-
reverse switch direction while the
lathe is running.
Changes the spindle speed range from
High (0 - 2500 RPM) to Low (0-1100
RPM).
speed control knob (180)
do not adjust the h/L gear shift
Lever while the Lathe is running.
Adjusts the Spindle (3) speed from 0 to
2500 RPMs.
Check that this knob is at 0 before
turning on the Lathe.
note: The Speed Control Knob (180) is
dependant on the H/L Gear Shift Lever
(33). When the H/L Gear Shift Lever is in
the Low setting, the Speed Control Knob
runs from 0 to 1100 RPM. When the H/L
Gear Shift Lever is in the High setting,
the Speed Control Knob runs from 0 to
2500 RPM.
reV 10b
Page 10
For technical questions, please call 1-800-444-3353.
SKU 93212
Download from Www.Somanuals.com. All Manuals Search And Download.
Lathe coMPonents oVerVieW
Following are brief descriptions of major components of the Mini Lathe.
Bed Way (1) - The Bed Way is the base of
the work area under the Chuck and
Tailstock. It is where the Tailstock and
Compound Rest are attached and what
they slide along.
tailstock (138) - The Tailstock holds the
Tailstock Quill (142) which is used to
hold various tools (sold separately) or a
Live Center (143).
thread indicator dial (302) - The Threading
Dial is used to measure the number of
rotations of the Lead Screw when thread
cutting. It eliminates the need to reverse
the lathe and return the carriage to the
starting point each time a successive
threading cut is taken. You must adjust
the Threading Dial so that it engages
the Lead Screw (129) in order for it to
function.
chuck (2) - The Chuck holds the three Jaws
(two sets included) which clamp the work
piece in place.
compound rest (105/108) - The Compound
Rest and Compound Slide (100) work
together to adjust the position of the
Cutting Tool to the desired location.
Jaws (166 & 168) - The Jaws fit into the
Chuck (2) and hold the workpiece in
place. There are a set of internal Jaws
(168), which fit inside the workpiece
and External Jaws (166) which fit on the
outside of the workpiece.
threading gears (45,50, 59, 157-165) - The
Threading Gears are positioned under
the Gear Drive Cover (53) on the far
left side of the Lathe. They are used in
various configurations for thread cutting.
Lead screw (129) - The Lead Screw controls
automatic feeding. In thread cutting or
when you want to cut into the workpiece
automatically, you engage the Lead
Screw with the Feeding Direction
tool Post (112) - The Tool Post sits on the
top of the Compound Rest (105/108) and
is used to hold various cutting tools by
clamping them in place with Tool Post
Bolts (110).
Selector (35) and use the Automatic
Feed Handle (79). Keep track of the cut
with the Thread Dial Indicator (302).
Live center (143) - The Live Center fits into
the Tailstock Quill (142) on the Tailstock
(138) and helps to hold the end of the
workpiece that is opposite from the
Chuck (2). A live center spins with the
workpiece and chuck, while a dead
center (sold separately) does not spin.
reV 10b
SKU 93212
For technical questions, please call 1-800-444-3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
to Mount the Lathe to a Workbench:
asseMBLY instructions
Drill holes for permanent mounting:
14-7/8”
note: For additional information regarding the
parts listed in the following pages, refer
to the Assembly Diagram near the end of
this manual.
1.
Warning! Make sure the Power
Switch of the tool is in its “OFF” position
and that the tool is unplugged from
its electrical outlet before making any
adjustments to the tool.
Figure 5
Unthread the Bolts (67) from the bottom
of the unit. Measure and drill holes in the
workbench. Use appropriate length M6-1
bolts and washers (sold separately) to
secure the Lathe and Chip Tray to the
workbench.
2. Clean off the protective grease on the
Mini Lathe.
installing handwheel handles
attaching rubber Feet or
installing to Workbench
Tailstock Quill Control Wheel (84a)
note: Mount or place the Lathe on a sturdy
workbench or table, with good lighting,
at a height that allows you to comfortably
work without back strain.
Cross Slide
Crank (86a)
The Lathe can be mounted permanently
to a workbench or used with it’s included
Rubber Feet (125) on a tabletop.
to attach the rubber Feet:
Feed Control Wheel (84b)
Chip Tray (126)
Bolts (67)
Handwheel Handles
Figure 6
1. To install the Handwheel Handles on the
Tailstock Quill Control Wheel (84a) and
the Feed Control Wheel (84b), use a
flathead screwdriver and a 14mm open
end wrench to thread the handles onto
the wheels.
Rubber Feet (125)
Bolts (67)
Figure 4
To attach the Rubber Feet to the bottom
of the Lathe, unthread the Bolts (67)
from the bottom of the Chip Tray (126).
Slide the Rubber Feet onto the Bolts
and re-thread them into the bottom of
the Lathe through the Chip Tray holes.
Tighten securely.
2. For packaging purposes, the Cross Slide
Crank (86a) is shipped from the factory
facing backwards. Adjust the Cross Slide
Crank (86a) to face forward using a 5mm
Hex Wrench (part of 311) to unthread the
Cap Screw (52) and turn the Cross Slide
Crank around. Tighten the Cap Screw
securely.
reV 10b
Page 12
For technical questions, please call 1-800-444-3353.
SKU 93212
Download from Www.Somanuals.com. All Manuals Search And Download.
Washer (239), Spring (237), and Nut
(240). Then, thread the Screw (238) into
the Compound Rest (108). Slide the
notch in the Protective Cover (235) over
the end of the Slotted Screw (236).
installing guards
Protective Cover (235)
Chuck Guard (201)
Figure 7
Figure 8
1. To install the Chuck Guard (201), remove
the two Screws (73) on the Hinge (202).
Attach the Chuck Guard (201) to the
Hinge using the Screws. The Chuck
Guard should be aligned so that it covers
the Chuck (2) when swung down over it.
Figure 9
2. To install the Protective Cover (235),
remove the Screw (238) from the
Compound Rest (108). Slide the Screw
(238) through the Protective Cover (235),
reV 10b
SKU 93212
For technical questions, please call 1-800-444-3353.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Feeding Direction Selector (35) to the
middle (Neutral).
set uP
Forward/OFF/Reverse Switch (181)
Fuse Holder (179)
initial test run
Before further set-up of the Lathe, check
that the power components are working
properly by performing the following test
run.
1. Check that all loose parts and tools are
out of the way and nothing will interfere
with the Chuck (2) when it rotates.
Power Switch (178)
Chuck (2)
Speed Control Knob (180)
Figure 12
5. On the front of the Lathe, make sure the
Forward/OFF/Reverse Switch (181) is
set to the OFF position.
6. Turn the Speed Control Knob (180) to
zero.
Warning: BeFore turning on the
Mini Lathe each tiMe it is to Be
used, the sPeed controL knoB
(180) Must Be set to zero.
Spindle (3)
Nuts (6)
Figure 10
2. Turn the Chuck by hand and check that it
rotates freely.
7. Plug in the electrical cord and turn
the Forward/OFF/Reverse Switch to
Forward.
3. Check that the three Nuts (6) on the
Chuck are tight.
8. Turn the Power Switch (178) to the ON
position.
Feeding Direction Selector (35)
9. Gently rotate the Speed Control Knob
clockwise past the 1 to the first setting.
The speed will increase the further the
Knob is turned. The Lathe should run
smoothly with little or no vibration or
friction sounds when it starts. If you
notice unusual sounds or vibrations, turn
off the Power Switch, turn the Speed
Control Knob to 0, unplug the machine
and have the problem corrected before
further use.
H/L Gear Shift Lever (33)
Figure 11
10. If the Lathe is running smoothly, continue
running it for several minutes, gradually
increasing the Speed Control Knob
4. On the back of the Lathe, set the H/L
Gear Shift Lever (33) to low and the
reV 10b
Page 14
For technical questions, please call 1-800-444-3353.
SKU 93212
Download from Www.Somanuals.com. All Manuals Search And Download.
setting, and letting it run for several
minutes at each setting before increasing
to the next level. Continue until you’ve
run the Lathe all the way up to the
highest setting.
replacement of chuck
Chuck (2)
11. Turn the Power Switch OFF and wait for
the Lathe to come to a complete stop.
12. Repeat the process with the H/L Gear
Shift Lever at the High setting. Then
repeat at both the Low, then High setting
with the Forward/OFF/Reverse Switch in
the Reverse position.
Warning: the Mini Lathe Must Be
coMPLeteLY stoPPed BeFore
changing the ForWard/oFF/
reVerse sWitch (181), the Feed
direction seLector (35), or the
gear shiFt LeVer (33).
Spindle (3)
Nut (6)
Figure 13
1. When replacing the Chuck, place a cloth
or a piece of wood on the bedway at the
bottom of the chuck. This step will help
avoid damage to the bedway caused by
accidentally dropping the chuck.
13. Turn the Power Switch off, the Speed
Control Knob to 0 and unplug the Lathe.
2. To replace the chuck, loosen the 3 Nuts
(6) as shown in Figure 13, remove the
old Chuck and replace with a new chuck.
Replace and tighten the Nuts.
14. Check the Compound Rest Crank (86b)
and the Cross Slide Crank (86a) to see
that the Compound Rest (105/108) and
Cross Slide work properly. If they are
too tight or too loose, adjust the Gibs
(94/107) located at both crank sides (See
Gib Adjustments in the Maintenance
Section of this manual).
replacement of Jaws
External Jaw Set (166)
Internal Jaw Set (168)
Insert this
end first
Number
Figure 14
The Lathe comes with two sets of
Jaws: an External Jaw Set (166) and
an Internal Jaw Set (168). Each piece
is numbered and fits into the Chuck
grooves with the corresponding number
reV 10b
SKU 93212
For technical questions, please call 1-800-444-3353.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
in the Chuck groove. The Jaws are
designed to work as complete sets. Do
not mix pieces from one set with the
other set when installing in the Chuck.
Lead thread of Scroll
a
Insert Jaw #1
B
Chuck
Key
(167)
Jaw
Scroll
Grooves
Chuck (2)
Chuck (2)
Figure 15
The jaws are held in place by a spiralled
scroll inside the Chuck which rotates
around the center of the chuck with the
Chuck Key. As the scroll rotates, it hooks
into the jaw ridges, then pulls each Jaw
toward the center of the Chuck as the
spiral of the scroll rotates around the
Chuck.
c
Insert Chuck
Key (167),
Turn Clockwise
Figure 16
To replace the Jaws:
a. Unplug the Lathe.
b. Place a towel under the Chuck to
protect the Bed Way (1) from any Jaws
that may be dropped. Carefully remove
any Jaws by inserting the Chuck Key
(167) into the side of the Chuck, turning
it counterclockwise, and sliding each
Jaw out of it’s slot as it becomes free.
c. Look at the Chuck so you can see
into the grooves, and find the groove
marked #1. Rotate the Chuck Key
clockwise until you see the lead thread
of the Scroll in groove #1 (A in Figure
16).
d. Slide Jaw #1 into the groove and
rotate the Chuck Key counterclockwise
reV 10b
Page 16
For technical questions, please call 1-800-444-3353.
SKU 93212
Download from Www.Somanuals.com. All Manuals Search And Download.
slightly, then clockwise, to engage the
lead thread into the Jaw (B and C in
Figure 16).
tailstock adjustments
The Tailstock (138) holds tools, such as
the Live Center (143), which are used
with the Chuck Jaws (167 or 168) to hold
work pieces in place.
e. Slide Jaw #2 into the next groove
and continue turning the Chuck Key
clockwise to advance the lead thread
into the next Jaw. Slide Jaw #3 with the
same procedure as Jaw #2.
Tailstock Quill Fix
Holder (146)
Tailstock
Quill (142)
Tailstock
(138)
Live Center
(143)
note: When mounting a workpiece, it is
recommended that all three jaws are
loosened at the same time. This will
protect the threads inside.
Underside
of
Tailstock
Tailstock
Quill
compound rest adjustment
Control
Wheel
(84a)
Nut (6)
Tailstock
Nut
(268)
Screw (197)
Figure 18
Compound Rest Crank (86b)
Compound Rest B (105)
1. Use the Tailstock Quill Control Wheel
(84a) to position the Live Center. Turning
the Wheel counterclockwise slides
the Live Center away from the Chuck,
turning it clockwise slides it toward
the Chuck. It can be adjusted up to
approximately 2”.
Bolt Holes
& Bolts (67)
Compound Rest A (108)
Figure 17
2. The Tailstock Quill (142) holds the
Live Center in place. To remove or
replace the Live Center, continue
turning the Tailstock Quill Control Wheel
counterclockwise until the Live Center
begins to slide out of the Quill. Insert
the Live Center or other tool (sold
separately) into the Quill and turn the
Tailstock Quill Control Wheel clockwise
to lock the tool in place.
To adjust the angle of Compound Rest:
a. Turn the Compound Rest Crank (86b)
counterclockwise to slide the top section
of the Compound Rest (Compound Rest
A (108)) so that the two screw holes
are exposed on the lower section of the
Compound Rest (Compound Rest B
(105)).
b. Turn the two Bolts (67)
3. You may need to slide the Tailstock
closer to, or further away from, the
Chuck before adjusting the Live Center.
To do so, loosen the Tailstock Nut (268),
adjust the Tailstock as needed, then re-
tighten the Nut. Use this method when
replacing the Tailstock as well.
counterclockwise to loosen them.
c. Swivel the Compound Rest to the
desired angle.
d. Tighten the two Screws.
reV 10b
SKU 93212
For technical questions, please call 1-800-444-3353.
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
4. The Tailstock Quill is locked in place with
the Tailstock Quill Fix Holder (146). Turn
it clockwise to lock the Quill in place and
counterclockwise to loosen it. Tighten the
Nut (6) underneath the Quill to eliminate
any play in the Quill.
until they are securely holding the tool in
place.
automatic Feeding
Feed Control
Wheel (84b)
5. To adjust the Tailstock slightly to the right
or left of center, loosen the Screw (197)
on the bottom of the Tailstock. Adjust,
then tighten.
OFF
ON
tool Post adjustment
Automatic Feel Lever (79)
Tool Post Lever (111)
Figure 20
Tool Post (112)
Tool Post Bolt (110)
The Automatic Feed Lever (79) controls
whether the Carriage (93) moves
automatically, or manually.
When the Lever is Up, the Lathe is in
Manual mode. Use the Feed Control
Wheel (84b) to slide the Carriage to the
right or left.
Cutter
(Sold separately)
When the Lever is Down, the Lathe is
in automatic mode. The carriage will
automatically move to the right or left
depending on whether it is set to forward
or reverse.
Figure 19
To adjust the position of the Tool Post
(112):
note: The Feed Control Wheel (84b) is locked
a. Turn the Tool Post Lever (111)
counterclockwise to loosen the Tool
Post.
when the automatic feed is ON.
b. Rotate the Tool Post as needed.
c. Hold the Tool Post in position while
turning the Tool Post Lever clockwise,
tightening the Tool Post in place.
To install a cutting tool (Sold separately):
a. Use the 1/4” Hex Wrench (part of 311)
to raise enough Tool Post Bolts (110)
to hold the tool. Use at least two Tool
Post Bolts to hold the tool in place (Turn
counterclockwise to raise).
b. Slide the tool under the raised screws
and hold it while lowering the screws
reV 10b
Page 18
For technical questions, please call 1-800-444-3353.
SKU 93212
Download from Www.Somanuals.com. All Manuals Search And Download.
b. Use the 5mm Hex Wrench (part of
311) to loosen the Plate (303) and the
Threading Dial Body (68).
threading dial
The Threading Dial (65) is used to align
and track the threads cut in a threading
project. It can only be used when the
Lathe is set to automatic feed (See
previous section on Automatic Feeding).
To set up the Threading Dial:
c. Rotate both pieces so the Pinion (66)
on the back side of the Threading Dial
Body makes contact with the Lead
Screw (129) (“Dial Engaged” in Figure
21, bottom photo).
d. Tighten both pieces in place and
remove the Wrench.
e. To dis-engage the Threading Dial Body
when not in use, loosen the Plate and
rotate the Dial away from the Lead
Screw (129), then retighten the Plate.
Lead Screw (129)
Threading Dial (65)
Plate (303)
Threading Dial Body (68)
Automatic Feel Lever (79)
Dial Disengaged - Rotate up to engage:
Loosen here
and here
Lead Screw
(129)
Pinion (66)
Dial Engaged:
Lead Screw
(129)
Pinion (66)
Hex Wrench (311)
(Remove before using Lathe)
Figure 21
a. Adjust the dial to line up with one of the
numbers or lines as needed (Consult
advanced information about cutting
threads with mini-lathes to determine
where to line up the dial for your
threading project).
reV 10b
SKU 93212
For technical questions, please call 1-800-444-3353.
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeat each time before using a Crank
in either direction when you need precise
measurements.
oPeration
start up
4. Adjust the Controls:
note: Not following this start-up procedure
will cause the Lathe to immediately
h
shutdown. This is an overload protection
feature for the circuit board and motor.
L
n
r
L
1. Begin with the Lathe unplugged.
2. Install the required Jaws (166 or 168)
into the Chuck (2).
Figure 23
a. On the back of the Lathe, set the
Spindle Speed with the H/L Gear Shift
Lever (33) and the feed direction with
the Feed Direction Selector (35).
3. Set up the work area as needed for your
project. You will need to:
a. Secure the workpiece in place.
b. Install the cutting tool (sold separately)
in the Tool Post (112).
Forward-OFF-Reverse Switch (181)
c. Set the Automatic Feed Lever (79) to
manual or automatic.
d. If threading, engage the Threading Dial
(65) and set it as needed for the project.
e. Move the cutting tool in place using the
Cross Slide (100) and Compound Rest
(105/108) Cranks (86a and 86b).
Power Switch (178)
Speed Control Knob (180)
Figure 24
b. On the front of the Lathe, make sure
that the Main Power Switch (178),
Forward/OFF/Reverse Switch (181) and
the variable Speed Control Knob (180)
are in their off positions.The variable
Speed Control Knob has an actual “0/
Off” position and will “click” when placed
in the “Off” position.
note: Before beginning any machining
process, remove backlash from the
Cross Slide (100) and/or Compound
Rest (105/108) Cranks (86a and 86b)
and reset the Dials (87) to zero.
Compound Rest Crank (86b)
note: the Lathe will not start-up unless
the Variable speed control knob is
turned to the “0/off” position before
restarting. attempting to start the
lathe with the speed control knob
(180) set at any speed other then “0/
off” or attempting to start the lathe
out of sequence, will cause the fuse
to blow.
Dials (87)
Cross Slide Crank (86a)
Figure 22
To do this, begin rotating the Crank in
the desired direction until all play is
gone. Hold the Crank in place with one
hand and rotate the Dial (87) to zero.
reV 10b
Page 20
For technical questions, please call 1-800-444-3353.
SKU 93212
Download from Www.Somanuals.com. All Manuals Search And Download.
to stop the Lathe
chuck guard
(201)
1. Turn the Speed Control Knob (180) to 0.
Properly in place
2. Move the Forward-OFF-Reverse Switch
to OFF.
safety
Mechanism
3. Turn the Power Switch (178) OFF.
4. Unplug the Lathe when not in use.
Pin (251) properly extended
into the recess, allowing
the lathe to operate.
rotating
Plate
(252)
safety
Mechanism
Figure 25
5. the chuck guard (201) has a safety
interlock and the Lathe will not
operate unless the guard is properly
in place. Install the guard if not already
done so. Check to ensure that the Guard
(201) is in its operating position over
the Chuck (2). The Pin (251) must be
correctly seated in the recess in the
Rotating Plate (252) for the Lathe to
work.
6. Plug in the Lathe.
Forward-OFF-Reverse Switch (181)
Power Switch (178)
Figure 26
Speed Control Knob (180)
7. Move the Power Switch (178) to the “On”
position (switch will turn Red) and place
the Forward-Off-Reverse Switch (181) in
the direction needed.
8. Move the Variable Speed Control Knob
(180) to the needed operating speed to
start the Lathe.
reV 10b
SKU 93212
For technical questions, please call 1-800-444-3353.
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Face cutting
Basic operations
Warning: Make sure the Lathe power is
off and the Lathe is unplugged before
setting up a project or working near the
Chuck (2).
Following are some of the basic
operations used with the Lathe. It is
recommended that you become familiar
with mini lathe techniques before using
this tool. Consult books on the subject
and/or web page resources for your
project before using this tool.
Figure 28
2. Use the chuck to hold the workpiece
firmly, and the cutter positioned as
shown above for face cutting. The edge
of the cutter must be at the same height
as the center.
holding a project between the chuck (2)
and the Live center (143)
internal cutting
(As seen from back of Lathe to show detail)
Figure 27
1. Use the chuck to hold the workpiece
firmly. Then, use the Live Center (143)
to fix the other end.
Figure 29
3. By changing the tool post angle and
adjusting the compound rest, you can
make internal cuts.
note: If you change the Live Center to a
drilling chuck (sold separately), you start
your drilling immediately.
reV 09c, 10b
Page 22
For technical questions, please call 1-800-444-3353.
SKU 93212
Download from Www.Somanuals.com. All Manuals Search And Download.
Bevel cutting
thread size gear settings
gear Box stud
threads
Per inch
a
B
c
d
12
13
14
16
18
19
20
22
24
26
28
32
36
38
40
44
48
52
40
40
40
40
40
40
40
40
40
40
20
20
20
20
20
20
20
20
30
30
35
40
45
57
50
55
60
65
35
40
45
57
50
55
60
65
65
60
50
60
Figure 30
4. After adjusting the angle of the
compound rest, you can make bevel
cuts.
50
60
threading gears
By changing the gear set-up it is possible
to cut any thread size. The factory set-up for
Mini Lathe gears is as follows:
Motor end view of Lathe with
Gear Drive Cover (53) removed:
A
A
B
D
B
a
B
D
A
c
A
d
example 1: To cut 12 threads per inch (see
illustration above), use 40T in position A,
30T in position D, and put any other gear
is position B to connect A and D.
B
C
B
C
D
D
A
A
B
B
C
D
C
Positions A and C= 20T
Positions B & D= 80T
D
To change the thread size, use the gear
box settings shown on the table that
follows.
example 2: To cut 38 threads per inch (see
illustration above), use 20T in position A,
57T in position D, 50T in position B, and
60T in position C.
reV 10b
SKU 93212
For technical questions, please call 1-800-444-3353.
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Position C= 20T
Position D= 80T
automatic Feed and threading dial
Once the gears are set up, you will need
to engage the Threading Dial (65) so you
can monitor the number of threads cut.
Set up the Threading Dial as described
in the set uP section under threading
dial.
Set the direction for the lathe with the
Forward/OFF/Reverse Switch.
Turn the Power Switch on (the switch will
light up).
Adjust the speed needed to cut the
threads (consult advanced information
about cutting threads with mini-lathes).
Use the following table, also located on
the front of the Lathe, to determine what
number to start threading:
indicator table
16t
t.P.i. scaLe t.P.i. scaLe
12
13
14
16
18
19
20
22
24
1, 3, 5, 7
1
26
28
32
36
38
40
44
48
52
1, 5
1, 3, 5, 7
1 ~ 8
1, 5
1 ~ 8
1, 5
1, 3, 5, 7
1, 5
1
1 ~ 8
1, 3, 5, 7
1, 5
1, 3, 5, 7
1 ~ 8
1 ~ 8
1, 3, 5, 7
Move the cutting blade to the proper
position. Pull down the Automatic
Feed Lever (79) to start threading
automatically.
To stop the automatic setting, pull up on
the Automatic Feed Lever.
Remember: After thread cutting
operation is complete, change back to
the factory set-up gear setting:
Position A= 20T
Position B= 80T
reV 10b
Page 24
For technical questions, please call 1-800-444-3353.
SKU 93212
Download from Www.Somanuals.com. All Manuals Search And Download.
Belt inspection and tensioning
Maintenance and
serVicing
1. Remove belt cover, if equipped.
Procedures not specifically
explained in this manual must
be performed only by a qualified
technician.
2. Examine belt for cracks, tears in the
backing, or other damage. Replace belt
if damaged according to steps below:
a. Loosen the motor mounting bolts and
slide the motor towards the other pulley
as far as possible.
to PreVent
serious inJurY
FroM accidentaL
oPeration:
b. Slide the old belt off of the smallest
pulley first, then remove it.
turn the Power switch of the tool
to its “oFF” position and unplug
the tool from its electrical outlet
before performing any
inspection, maintenance, or
cleaning procedures.
c. Put the new belt around the larger
pulley first, then around the smaller
pulley.
d. Move the motor away from the other
pulley until it is properly tensioned
according to the directions below.
Tighten the motor mounting bolts.
to PreVent serious inJurY
FroM tooL FaiLure:
do not use damaged equipment.
if abnormal noise or vibration
occurs, have the problem
3. Check and adjust belt tension according
to the steps below:
Deflection
distance
corrected before further use.
cleaning, Maintenance, and
Lubrication
1. BeFore each use, inspect the
general condition of the tool. Check for
loose hardware, misalignment or binding
of moving parts, cracked or broken parts,
damaged electrical wiring, and any
other condition that may affect its safe
operation.
a. Press on the center of the longest
span on the belt with moderate finger
pressure. Then measure the deflection
distance, the distance that the belt
moved. The belt should deflect about
1/4”.
2. aFter use, wipe external surfaces of
b. If the belt deflects too much, tighten
belt by loosening the motor mounting
bolts and moving the motor away from
the other pulley slightly. Secure motor
mounting bolts and retest tension. If the
belt is too long to be properly tensioned,
it must be replaced.
the tool with clean cloth.
3.
Warning! if the supply cord of
this power tool is damaged, it must be
replaced only by a qualified service
technician.
c. If the belt deflects too little, loosen
belt by loosening the motor mounting
reV 10b
SKU 93212
For technical questions, please call 1-800-444-3353.
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
bolts and moving the motor towards the
other pulley very slightly. Secure motor
mounting bolts and retest tension.
Compound Rest A (108)
Gib Screws (106)
and Nuts (98)
Cross
Slide
(100)
4. Before use, replace belt cover if
equipped.
gib adjustments
Compound Rest A (108)
Gib Screws (99)
and Nuts (98)
Gib (94)
Gib (107)
Figure 32
Cross
Slide
(100)
To make the adjustment:
1. Unplug the Lathe.
2. Working one set of three gib Screws and
Nuts at a time, loosen the three Nuts
(98) with a wrench (sold separately).
Gib (94)
Compound Rest
Crank (86B)
3. Holding the center Nut with the wrench,
loosen or tighten the Center Screw (99
or 106) with a flat head screw driver
(sold separately) and check the sliding
movement. It should be even and
smooth while removing any play. Adjust
as needed, then, holding the Screw with
the screw driver, tighten the Nut with the
wrench.
Cross Slide
Crank (86A)
Figure 31
4. Repeat step 3 for the two side Screw/Nut
sets.
Adjusting the metal strips, or Gibs
(94/107) on the underside of the
Compound Rest A (108) and the Cross
Slide (100) helps to snug up those units
so they slide smoothly along the lathe.
The goal is to tighten them enough so
that the Compound Rest and Cross Slide
do not have any unnecessary movement,
but not so tight that they bind. It should
not be difficult to turn the hand Cranks
(86A/86B).
tailstock alignment
The Tailstock (138) needs to be adjusted
for offset, then re-aligned before first use
and any time the tool in the Tailstock is
changed.
To align the Tailstock:
1. Center drill both ends of a 6” long piece
of round cold rolled stock. Set aside.
The Gibs become loose with use, so
the Compound Rest A and Cross Slide
should be checked periodically for any
play. Readjust the Gibs as needed.
2. Turn a 60° point on a piece of scrap
metal to make a dead center.
reV 10b
Page 26
For technical questions, please call 1-800-444-3353.
SKU 93212
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Place the dead center in the Tailstock.
replacement of carbon Brushes
4. Attach a Lathe Dog (part of SKU 3448 -
sold separately) the to 6” piece from step
1 and mount between centers.
Carbon Brush Cover
5. Turn approximately 0.010” off of the
diameter of the mounted workpiece.
Feed
Control
Wheel (84b)
6. Measure the workpiece with a
micrometer at the Tailstock end and the
Chuck end. Divide any difference by
two. If it is thicker at the Chuck (2) end,
move the tailstock away from you by the
resulting amount. If it is thicker at the
Tailstock end, move the Tailstock closer
to you by the resulting amount.
Front - Bed Way (1)
Carbon Brush Cover
Plug
7. Turn another 0.010” off of the workpiece.
Back - Motor Cover (151)
Carbon Brush Cover
8. Repeat steps 5 and 6 as needed until
there is no taper and/or the desired
amount of accuracy is achieved.
Carbon Brush (318)
Figure 33
1. Unscrew the Brush Covers on the front
and back of the machine using a flat
head screwdriver (sold separately).
2. Pull the Brush out, noting the orientation
of the old Carbon Brushes to prevent
needless wear if they will be reinstalled.
3. The Carbon Brushes are approximately
5/8” long. If either one is worn down by
more than 1/2, replace both Brushes.
4. To clean old Carbon Brushes, rub the
contact areas with a pencil eraser.
5. Carefully, without forcing them, insert
the Carbon Brushes. Make sure the
carbon portions of the brushes contact
the motor armature and that the springs
operate freely. If reinserting a used brush
make sure it is in the same orientation to
reduce wear.
6. Replace the Brush Covers.
For technical questions, please call 1-800-444-3353. Page 27
reV 10b
SKU 93212
Download from Www.Somanuals.com. All Manuals Search And Download.
replacing the Fuse
The Fuse (314) is located in the Fuse
Holder (179) on the Control Panel (122).
The Fuse Holder is spring fitted.
Fuse Holder (179)
Control Panel
To remove Fuse Holder (179)
(122)
Press down, then turn counterclockwise.
Fuse (314)
Fuse Holder (179)
Figure 34
Fuse Holder Socket
1. To Remove the Fuse Holder:
a. Insert a flathead screwdriver (sold
separately) into the slot in the Fuse
Holder.
b. Press down and turn counterclockwise
1/4 turn.
c. Release pressure. Pull the Fuse Holder
and Fuse out of the socket.
d. Replace with a new 250V 3 amp mini
glass fuse.
2. To Replace the Fuse Holder, slide it into
the Fuse Holder Socket and press in
with the screw driver, turning clockwise
until the Fuse Holder clicks into place.
Release pressure. The Fuse Holder will
be flush with the rim of the Fuse Holder
Socket.
reV 10b
Page 28
For technical questions, please call 1-800-444-3353.
SKU 93212
Download from Www.Somanuals.com. All Manuals Search And Download.
troubleshooting
Problem
Possible causes
Likely solutions
Motor and Electrical
Lathe will not start
or a breaker trips on
startup.
1. Cord not connected.
2. No power at outlet.
1. Check that cord is plugged in.
2. Check power at outlet. If outlet is unpowered,
turn off tool and check circuit breaker. If breaker
is tripped, make sure circuit is right capacity for
tool and circuit has no other loads.
3. Fuse has blown.
3. Check for short, replace fuse (see Maintenance
section of this manual).
4. Chuck Guard safety interlock not 4. Rotate Pin (251) so it seats in Plate (252).
in place.
5. PC Board (182) faulty.
5. Inspect PC Board, have replaced if needed.
6. Check and replace as needed.
6. Power Switch (178), Forward/
OFF/Reverse Switch (181) and/
or Speed Control Knob (180) not
working.
7. Internal damage or wear. (such 7. Have technician service tool.
as wiring or motor.)
Lathe stalls.
1. Incorrect workpiece material
(metal).
1. Use metal suited for Lathe.
2. Drive Pulleys slipping on shaft.
2. Tighten or Replace Pulleys (27,148).
3. Removing too much material per 3. Remove less material per pass.
pass.
Lathe operates
slowly.
Extension cord too long or wire size Eliminate use of extension cord. If an extension
too small.
cord is needed, use shorter/heavier gauge cord.
See Extension Cords in GROUNDING section.
1. Keep cutting accessories sharp. Replace as
needed.
Performance
decreases over time.
1. Accessory dull or damaged.
2. Carbon Brushes (318) worn or
damaged.
2. Replace Carbon Brushes (See Maintenance
section of this manual).
Excessive noise or 1. Pulley setscrews missing or
1. Check Pulley keys and setscrews. Replace or
tighten as needed.
rattling.
loose.
2. Motor fan hitting cover.
2. Tighten fan cover or replace as needed.
3. Properly tension belt.
3. Belt (if equipped) too loose
(slipping) or too tight (bearing
damage).
4. Internal motor damage or wear.
4. Have technician service tool.
Follow all safety precautions whenever diagnosing or servicing the tool.
disconnect power supply before service.
reV 10b
SKU 93212
For technical questions, please call 1-800-444-3353.
Page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Overheating.
Possible causes
1. Motor overloaded.
Likely solutions
1. Reduce load on motor. Loosen drive Belt (see
Maintenance section of this manual).
2. Forcing machine to work too fast. 2. Allow machine to work at its own rate.
3. Accessory dull or damaged.
3. Keep cutting accessories sharp. Replace as
needed.
4. Incorrect RPM or feed rate.
4. Check that RPM feed rate chart for appropriate
rates for operation.
5. Gear setup is too tight, gears
bind.
5. Adjust gears so there is a small amount of play
and the gears move freely and smoothly when
the Chuck is rotated by hand.
6. Blocked motor housing vents.
6. Wear ANSI-approved safety goggles and NIOSH-
approved dust mask/respirator while blowing dust
out of motor using compressed air.
7. Motor being strained by long or
small diameter extension cord.
7. Eliminate use of extension cord. If an extension
cord is needed, use one with the proper diameter
for its length and load. See Extension Cords in
GROUNDING section.
tool Performance
Whole unit vibrates 1. Workpiece unbalanced.
1. Re-center workpiece.
excessively while in
use.
2. Loose or damaged belt(s).
2. Tighten or replace the belt.
3. Align Drive Pulleys (27, 148).
4. Inspect gears and replace if needed.
3. Drive Pulleys not aligned.
4. Worn or broken gear.
5. Chuck loose or unbalanced.
5. Tighten Nuts (6) or have a qualified technician
rebalance Chuck.
6. Spindle bearings worn.
6. Have a qualified technician replace bearings.
Uneven surface
finish.
1. Incorrect RPM or feed rate for
job.
1. Adjust RPM and/or feed rate.
2. Dull or incorrect tool for job.
3. Gibs need adjustment.
2. Sharpen and/or change tool.
3. Tighten Gibs (99 and/or 106) (See Gib
Adjustment in Maintenance Section).
4. Tool positioned too high.
Quill not fully seated in Tailstock
or taper was inserted without first
removing debris.
4. Lower position of tool.
Unable to remove
tapered tool from
Tailstock.
Turn quill handwheel until taper is forced out of quill.
In the future make sure that the quill is fully seated
in the tailstock and that the tool is wiped free of
debris before installing.
Cross Slide,
1. Gibs need adjusting.
1. Loosen or tighten the Gib screws (99 and/or 106)
(See Gib Adjustment in Maintenance Section).
Compound Slide
and/or carriage
feed do not move
smoothly.
2. Handwheel or crank handles are 2. Tighten Handwheel and/or crank handle.
too loose.
3. Leadscrew worn or needs
adjustment.
3. Tighten Leadscrew fasteners or have lead screw
replaced by a qualified technician.
Follow all safety precautions whenever diagnosing or servicing the tool.
disconnect power supply before service.
reV 10b
Page 30
For technical questions, please call 1-800-444-3353.
SKU 93212
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Difficulty moving
Cranks of Cross
Slide, Compound
Slide and/or
Possible causes
Likely solutions
1. Remove Gibs, clean Gibs and all adjacent areas.
Re-lubricate, then reinstall Gibs.
1. Debris jammed around Gibs.
2. Gibs adjusted too tight.
2. Loosen Gib screws (99 and/or 106) and lubricate
bedways.
Carriage Handwheel.
3. Bedways need lubrication.
1. Tool Post (112) too loose.
3. Lubricate bedways.
1. Clean any debris around Tool Post, then securely
tighten Tool Post.
Cutting Tool
or machine
components vibrate
excessively during
operation.
2. Cutting tool jutting too far out of
Tool Post or not secure.
2. Remove and reinstall cutting tool so that at least
two screws hold it securely in place and no more
than 1/3 of the tool extends beyond the Tool Post.
3. Gibs need adjustment.
3. Adjust Gib screws (99 and/or 106).
4. Sharpen or replace tool.
4. Cutting tool need sharpening.
5. RPM or feed rate incorrect for
job.
5. Check and adjust for recommended RPM and/or
feed rate.
Finished piece
uneven from one
end to the other.
Difficulty moving
Chuck Jaws.
Carriage will not
feed.
Chuck and Tailstock are not aligned. Realign Tailstock following Tailstock Alignment
instructions in the maintenance section of this
manual.
Debris lodged between Jaws and
Chuck.
Remove Jaws. Clean and lubricate Chuck threads,
then reinstall Jaws.
1. Gear or gears not engaged.
1. Check gears and adjust positions.
2. Damaged gears.
2. Check and replace damaged gears.
3. Tighten feed handle screw.
3. Feed Handle screw loose.
Follow all safety precautions whenever diagnosing or servicing the tool.
disconnect power supply before service.
PLease read the FoLLoWing careFuLLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE
OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED
TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY
CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK
AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT
PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
reV 10b
SKU 93212
For technical questions, please call 1-800-444-3353.
Page 31
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
Part
1
2
3
4
6
7
8
9
description
Qty
Part
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84a
84b
85
86A
86B
87
88
89
90
91
92
93
94
95
description
Qty
1
1
10
1
3
1
1
2
2
1
1
1
2
1
1
1
1
1
4
1
1
2
1
1
2
1
1
4
6
2
1
1
1
1
6
6
3
1
2
1
1
3
1
1
1
8
1
1
1
1
1
2
2
1
1
1
1
1
Bed way
Chuck
Spindle
Stud M6 x 25
Nut M6
Key 5 x 40
Key 4 x 8
1
1
1
3
5
1
2
6
2
2
2
1
1
1
1
2
1
2
3
3
2
2
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
1
1
2
1
1
1
1
2
2
6
2
1
2
1
12
2
1
2
1
1
3
3
1
Threading Dial
Pinion 16T
Bolt M6 x 16
Threading Dial Body
Set screw M4 x 10
Apron
Gib strip
Washer
Set Screw M5 x 12
Cover
Ball bearing 80206
Spacer
Headstock casting
H/L gear 21T/29T
Spacer
Spur gear 45T
Nut M27 x 1.5
Set screw M5 x 8
Steel ball 5
Compression spring
Set screw M6 x 8
Retaining ring 12
Ball bearing 6201Z
H/L gear 12T/20T
Parallel key 4 x 45
H/L gear shaft
Pulley
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
Screw M4 x 8
Shaft
Half nut base
Angle block
Screw M4 x 10
Groove cam
Automatic Feed Lever
Shaft
Feeding gear 11T/54T
Feeding gear 24T
Screw M6 x 10
Wheel (Tailstock Quill Control)
Wheel (Feed Control)
Knob
Cross Slide Crank
Compound Rest Crank
Dial
Bracket
Retaining ring 10
Timing belt L136
Shifting fork
Feeding screw
Nut M5
Screw M6 x 12
Slide plate
Shifting arm
Shifting knob
H/L Speed Gear Shift Lever
Shifting grip
Feed Direction Selector
Handle mount
Spring
Carriage
Gib strip
Feeding nut imperial
Swivel disk
Screw M8 x 20
Nut M4
Screw M4 x 16
Cross slide
Screw M5 x 10
Screw M4 x 8
Compound rest (B)
Screw M4 x 14
Gib strip
Compound rest (A)
Position pin
Tool Post Bolt M6 x 25
Tool Post lever
Tool Post
96
97
98
99
Indicator
Pinion 25T
100
101
102
105
106
107
108
109
110
111
112
113
114
115
116
119
120
121
122
123
124
Support screw
Pinion 20T
Fixed cover
Screw M6 x 20
Gear 45T
Shaft
Parallel key 3 x 8
Mount
Screw M5 x 18
Gear 20T
Washer M6
Stud M10 x 65
Cross feed screw
Bracket
Screw M4 x 12
Nut M18
Cap Screw M6 x 8
Gear Drive Cover
Screw M5 x 45
Thread cutting chart
Screw M5 x 8
Washer M4
Model label
Dial indicator label
Control Panel
Control box
Bushing w/key
Gear 80T
Shaft
Support plate
Washer 8
Nut M8
Shaft
Power Cord
*not shown on assembly diagrams.
reV 10b
Page 32
For technical questions, please call 1-800-444-3353.
SKU 93212
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List (continued)
Part
125
126
127
128
129
131
133
134
135
136
137
138
139
140
141
142
143
144
145
146
148
150
151
152
153
description
Qty
4
1
1
1
1
1
3
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
Part
194
195
196
197
198
199
200
201
202
205
206
207
208
209
210
211
212
235
236
237
238
239
240
251
252
253
254
255
256
257
258
265
266
267
268
269
270
271
272
273
300
301
302
303
304
description
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
2
1
1
1
1
1
1
1
1
1
2
1
1
1
1
3
2
2
2
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
Rubber foot
Chip tray
Bracket
Key M3 x 16
Lead screw
Bracket
Screw M4 x 38
Nut M4
Tailstock plate
Screw M5 x 16
Flange
Screw M5 x 25
Key 3 x 12
Screw M3 x 10
Rack
Clamp plate
Washer M10
Screw M5 x 16
Tailstock
Chuck Guard
Hinge
Spring washer 6
Big washer 6
Spring
Tailstock screw
Bracket
Washer 6
Screw M3 x 4
Switch cover
Screw M5 x 16
Fixed cover
Protective cover
Slotted screw
Compression spring
Screw M6 x 30
Small washer 6
Hexagon nut M6
Pin
Screw M4 x 10
Tailstock quill
Live Center
Stud M8 x 40
Clamp
Tailstock Quill Fix Holder
Pulley
Motor
Motor Cover
Cable Roller
Rear splash guard
Rotate plate
Screw 2.9 x 4.5
Cover
157* Gear 30T
158* Gear 35T
159* Gear 40T
160* Gear 45T
161* Gear 50T
162* Gear 55T
163* Gear 57T
164* Gear 60T
Micro Switch
Dustproof sleeve
Protective Cover for Leadscrew
Screw M5 x 8
Spring Washer 6
Big Washer 6
Screw M6 x 25
Tailstock Nut M10
Screw M5 x 14
Leadscrew Support
Nut M4
Protective Cover
Screw M4 x 6
Screw
Label
Thread Dial Indicator
Plate
165* Gear 65T
166* External jaws (set)
167* External Jaw (set)
168* Internal Jaw (set)
170
171
172
173
174
175
176
177
178
179
180
181
182
184
185
186
187
188
190
191
192
193
Screw M4 x 8
Clamp block
Check ring 8
Screw M5 x 10
Protector
1
1
1
4
1
2
2
2
1
1
1
1
1
1
1
1
1
1
2
1
2
2
Screw M5 x 10
Nut M6
Screw M6 x 25
Power switch
Fuse Holder
Speed Control Knob
Forward/OFF/Reverse Switch
PC board
Screw M5 x 10
Spring washer 5
Washer 5
Screw M6 x 12
310* Oil can
311*
L hex wrench set S: 3,4,5,6
312* Double end wrench 8-10
313* Double end wrench 14-17
314* Fuse
318* Carbon brush set
*not shown on assembly diagrams.
Key 3*16
Spacer
Spring
Washer 8
Spring washer
Screw M8 x 55
reV 10b
SKU 93212
For technical questions, please call 1-800-444-3353.
Page 33
Download from Www.Somanuals.com. All Manuals Search And Download.
asseMBLY diagraM
reV 10b
Page 34
For technical questions, please call 1-800-444-3353.
SKU 93212
Download from Www.Somanuals.com. All Manuals Search And Download.
asseMBLY diagraM (continued)
b
a
record Product’s serial number here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not available
individually as replacement parts.
reV 10b
SKU 93212
For technical questions, please call 1-800-444-3353.
Page 35
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring diagraM
FC250BJ/110V
CONTROLLER
DC
Output
AC
Input
SAFETY
SWITCH
Rev
Off
F/O/R
SWITCH
POTENTIOMETER
For
POWER
CORD
Black
White
POWER
SWITCH
MOTOR
reV 10b
Page 36
For technical questions, please call 1-800-444-3353.
SKU 93212
Download from Www.Somanuals.com. All Manuals Search And Download.
LiMited 1 Year / 90 daY WarrantY
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that for a period of ninety
days from date of purchase that the engine/motor, the belts (if so equipped), and the blades
(if so equipped) are free of defects in materials and workmanship. Harbor Freight Tools also
warrants to the original purchaser, for a period of one year from date of purchase, that all other
parts and components of the product are free from defects in materials and workmanship (90
days if used by a professional contractor or if used as rental equipment). This warranty does
not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents,
repairs or alterations outside our facilities, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental,
contingent, special or consequential damages arising from the use of our product. Some states
do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF
ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the complaint
must accompany the merchandise. If our inspection verifies the defect, we will either repair or
replace the product at our election or we may elect to refund the purchase price if we cannot
readily and quickly provide you with a replacement. We will return repaired products at our
expense, but if we determine there is no defect, or that the defect resulted from causes not
within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which
vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 93212
For technical questions, please call 1-800-444-3353.
Page 37
Download from Www.Somanuals.com. All Manuals Search And Download.
|