2 PIECE SOLAR LIGHT SET
95745
assembly and Operating instructiOns
read this material before using this product.
Failure to do so can result in serious injury.
saVe this manual.
Copyright© 2008 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight
Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual
product may differ slightly from the product described herein. Tools required for assembly and service may not
be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 10f
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Use eye protection. Always wear ANSI approved impact safety goggles when setting up this
product.
10. Maintain products with care. Keep the Solar Spotlights clean for better and safer
performance. Inspect the Solar Spotlights periodically. if damaged, have it repaired by an
authorized technician.
11. Do not overreach. Keep proper footing and balance at all times.
12. Use the right Solar Spotlight for the job. Do not attempt to force a small Solar Spotlight to
do the work of a larger Light. There are certain applications for which this Solar Spotlight was
designed. Do not modify these products and do not use this Solar Spotlights for a purpose for
which it was not intended.
13. Do not set up the Solar Spotlights if under the influence of alcohol or drugs. Read
warning labels on prescriptions to determine if your judgement or reflexes are impaired while
taking drugs. If there is any doubt, do not set up the Solar Spotlights.
14. Keep the Solar Panel free of dirt, dust and grime. Dust covering the Solar Panel will
block out sunlight causing a decrease or stoppage of efficiency in recharging the
batteries.
WARNING: NiCd batteries must be recycled or disposed of properly. Do not incinerate. Batteries
may burst, causing personal injury and/or property damage. Contact your local
hazardous waste disposal authority for proper disposal.
WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood by
the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
Unpacking
When unpacking the 2 Piece Solar Spotlights, check to make sure parts on page 5 are included. If
any parts are missing or broken, please call HARBOR FREIGHT TOOLS at 1-800-444-3353.
Assembly/ Operation
Your 2 Pc. Solar Spotlights will require complete assembly. The Solar Spotlights requires special
conditions for set up and operation. It is important that you read the entire manual to become familiar
with the product BEFORE you use the Solar Spotlights. Before operating the Solar Spotlights be sure
that you have all parts described in the Parts List and Assembly Diagram located on page 5 of this
manual.
1. Decide where you want to place the Solar Spotlights. Choose a location that receives full,
direct sunlight a minimum of six hours a day. The location should not be near nighttime light
sources such as porch lights or streetlights as this may trigger the lights to turn off or flicker.
2. The Solar Spotlights will need to charge for at least 6 hours before using for the first time.
3. Each light is powered by two “AA” batteries. Each battery has a pull tab that keeps the battery
disconnected until you are ready to use the Solar Spotlights To access the battery,
see steps 4, 5 and 6. Refer to the section, “Replacing the Battery” and see Figure 1.
SKU 95745
For technical questions please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Unscrew the battery cover located at the rear of the Spotlight by twisting it counterclockwise.
See Figure 1.
Battery Cover
Figure 1
Figure 2
5. Located underneath the two batteries is an “Auto/Off” Switch-see Figure 2. Turn the switch to
the “Auto” position. Moving the Switch to “Auto” will automatically turn on the Solar Spotlight
during the night. Check to make sure that the two batteries are installed correctly, then twist the
battery cover back on. See Figure 2.
6. After the initial charge is set, check to see that the LED Lights are on by viewing the light at
night or in a dark location. If the LED Lights (2) are not lit, check the position of the “Auto”
Switch.
Note: During the day, the Solar Panel converts sunlight into electricity, recharging the batteries.
The amount of light the Solar Panel receives depends on placement of the Solar Spotlights,
geographic location and weather. If the weather is cloudy and the panel did not receive a full
charge, the Solar Spotlights may not achieve the full hours of operating time. They will catch
up on their own after two to three days of full sun.
7. Insert Nut (4) into nut-shaped hole of Stake (3), then thread in Knob (1) - see Assembly
Diagram.
Warning: Before inserting the Solar Spotlight into the ground, makcertain to choose
an area where there are no underground pipes, cables or other obstructions. Make
certain that the ground is soft enough to accept the Stakes (7). Gently insert them
into the ground making certain that it is in solid. Make certain that the Stake is
completely inserted into the ground to assure full stability for the Solar Spotlight.
8. The Light Assembly (2) rotates up and down to obtain the best lighting situation. The Solar
Panel pivots on a ball and can be set to a number of different angles to obtain the best angle for
solar power.
Rev 07e, 08i, 10f
SKU 95745
For technical questions please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Battery
It is recommended that you replace the battery every 12 months. Before performing any maintenance
on the Solar Spotlight, make certain that the “Off-Auto Switch is in the “OFF” position.
1. Unscrew the battery cover located at the rear of the Spotlight. See Figure 1, page 4.
2. Remove the old batteries. Make certain that the new batteries are “AA” , Ni-Cd rechargeable.
Install the new battery into the battery compartment. Make certain that the battery is placed
according to the correct polarity. Replace the battery cover.
Maintenance
Clean regularly with a damp towel. Do not use any type of solvent for cleaning. Do not put
too much pressure on the light or components while cleaning. Dry thoroughly.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL
ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO
THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO
REPLACE ANY PARTS OFTHE PRODUCT. IN FACT,THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATESTHAT ALL
REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSEDTECHNICIANS AND NOT BYTHE
BUYER.THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT
OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Note: Some parts are listed and shown for illustration purposes only and are not available individually
as replacement parts.
Parts List
Assembly/Parts Diagram
Part
Description
Knob
Quantity
1
2
3
4
2
2
2
2
Light Assembly
Stake
Nut
4
1
3
2
REV 03/07
07e, 08i
SKU 95745
For technical questions please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
|