All purpose
solAr lAntern
94740
Assembly And operAtion instructions
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
to preVent serious injury, reAd And understAnd
All wArnings And instructions before use.
Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
for technical questions or replacement parts, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
5.
do not abuse the power cord. never use the power cord to carry the adapter
or pull the plug from an outlet. Keep the power cord away from heat, oil,
sharp edges, or moving parts. replace damaged power cords immediately.
Damaged Power Cords increase the risk of electric shock.
Always wear eye protection. Always wear ANSI-approved safety goggles when
performing maintenance on this product.
6.
7.
do not use the product for a purpose for which it is not intended.
do not use the product if the power switch does not turn it on or off. Any
product that cannot be controlled with the Power Switch is dangerous and must be
replaced.
8.
disconnect the power cord plug from the power source before making any
adjustments, changing accessories, or storing the product. Such preventive
safety measures reduce the risk of starting the product accidentally. Always un-
plug the product from its electrical outlet before performing any inspection,
maintenance, or cleaning procedures.
9.
store lantern out of reach of small children.
10.
check for breakage of parts and any other condition that may affect the
product’s operation. if damaged, have the product serviced before using.
Many accidents are caused by poorly maintained products.
11.
use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one product may become hazardous
when used on another product.
12.
13.
product service must be performed only by qualified repair personnel. Service
or maintenance performed by unqualified personnel could result in a risk of injury.
when servicing a product, use only identical replacement parts. follow
instructions in the “Inspection, Maintenance, And Cleaning” section of this
manual. Use of unauthorized parts or failure to follow maintenance instructions
may create a risk of electric shock or injury.
14.
15.
maintain labels and nameplates on the product. These carry important informa-
tion. If unreadable or missing, contact Harbor Freight Products for a replacement.
never leave the product unattended when its adapter is plugged into an elec-
trical outlet. Turn off the product, and unplug the adapter from its electrical outlet
before leaving.
16.
17.
use only rechargeable batteries when replacing the batteries. Do not substitute
with any other size or type of battery.
never mix new and old batteries or batteries of different types together. Mix-
ing batteries may result in fire, leakage, or explosion.
SKU 94740
for technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
18.
nicd batteries must be disposed of or recycled properly. Do not incinerate.
Batteries may burst, causing personal injury and/or property damage. Contact your
local hazardous waste disposal authority for disposal or recycling.
unpAcKing
When unpacking, check to make sure that the product is intact and undamaged.
If any parts are missing or broken, please call Harbor Freight Tools at the number shown
on the cover of this manual as soon as possible.
note: The AC Adapter is located inside of the Bottom Cover. See instructions for
removing the AC Adapter on page 6.
operAting instructions
note: For additional information regarding the parts listed in the following pages, refer to
the Assembly diagram at the end of the manual.
1.
Turn the switch to the “OFF”position – the unit will charge much faster if it is switched
off while charging. Charge the batteries by using the wall adapter, car adapter,
or sitting the Solar Lantern in the sunlight for an extended period. if using the
automobile outlet, be aware that it will use up power and can drain the car
battery.
2.
3.
Once the lantern is charged, turn the switch to the “ON” position to illuminate the
lantern. Turn the switch to off to conserve power when done.
If the Solar Lantern stops working or is not holding a charge, replace the batteries
- see next page.
SKU 94740
for technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
bAttery replAcement
1.
2.
Turn the Solar Housing Lid (7) slightly counterclockwise.Remove the Solar Housing
Lid (7) from the top of the Solar Lantern. See Figure 1.
Remove the three Screws from the Battery Cover (6). See Figure 2.
Solar Housing (7)
Battery
Cover (6)
Led
Cover
(4)
Figure 2
Batteries (9)
Figure 1
3.
4.
With the Solar Housing Lid (7) off, gently twist off the Battery Cover (9) with the LED
Strip of 12 Bulbs (5) and LED Cover (4) assembly. Move the Battery Cover aside,
being careful not to disturb the wires and the internal components. See Figure 2.
Removed the dead batteries and dispose of them or recycle them properly according
to the Solid Waste Disposal regulations. Replace with new Rechargeable Batteries.
The polarity of the batteries is marked. Be careful of the internal components and
do not disturb the wires. See Figure 2.
5.
Once the batteries are in place, return the Solar Housing Lid (7) and twist clockwise
onto the Light Cover (3). Tighten.
SKU 94740
for technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
AdApter storAge compArtment
1.
Remove the Protective Cover (16) from the bottom of the Solar Lantern by pulling
down. Set the Cover aside. See Figures 3 & 4.
Protective
Cover (16)
Figure 4
Bottom Cover (1)
AC Adapter (15)
AC Adapter
Bracket (13)
Wing Nuts (14)
Figure 3
Protective
Cover (16)
2.
3.
Unscrew the Bottom Cover (1) from the base of the Lantern.
Inside of the Bottom Cover (1) is the AC Adapter (15) held in place by the AC Adapter
Bracket (13). Remove the Wing Nuts (14). Set the AC Adapter Bracket and Wing
Nuts aside. Remove the AC Adapter. Use this Adapter in a household electric outlet
for charging the Solar Lantern. See Figure 4.
4.
After charging, fold up the wiring of the AC Adapter (15) and store in the Bottom
Cover (1), using the AC Adapter Bracket (13) to hold it in place.With the AC Adapter
Bracket in place, tighten the Wing Nuts. Thread the assembly back on the bottom
of the Lantern. Replace the Protective Cover (16). See Figure 4.
inspection, mAintenAnce, And cleAning
1.
2.
3.
wArning! Make sure the Power Switch (17) of the Solar Lantern is in its
“OFF” position and that the Adapter is unplugged from its electrical outlet before
performing any inspection, maintenance, or cleaning procedures.
before eAcH use, inspect the general condition of the Lantern. Check for loose
screws, cracked or broken parts, damaged electrical wiring, and any other condition
that may affect its safe operation. do not use damaged equipment.
Clean the outside of the Lantern with a clean damp cloth. Never use abrasive clean-
ers; they will damage the unit. You may use a mild detergent. Never submerge
the Lantern in water or any other liquid. Dust covering the Plastic Light Cover will
block out sunlight causing a decrease or stoppage of efficiency in recharging the
batteries.
SKU 94740
for technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
pArts list
part
description
Q’ty
part
description
Q’ty
1
2
3
4
5
6
7
8
9
Bottom Cover
1
1
1
1
1
1
1
1
3
10 Screw
3
Base
Fuse* (F3AL250V)
*within Car Adapter (12)
11
1
Lens Cover
LED Cover
12 Car Adapter
1
1
2
1
1
1
LED Strip (12 LED’s)
Battery Cover
Solar Housing
Handle
13 AC Adapter Bracket
14 Wing Nut
15 AC 120V Adapter
16 Protective Cover
17 ON/OFF Switch
AA NiCd Battery
pleAse reAd tHe following cArefully
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION ORWARRANTY OF ANY KINDTOTHE BUYERTHAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIEDTO REPLACE ANY PARTS OFTHE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
LIMIted 90 dAy
wArrAnty
Harbor FreightTools Co.makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for
the period of ninety days from the date of purchase. This warranty does not apply to damage due directly or
indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, or to lack of
maintenance.We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent,
special or consequential damages arising from the use of our product. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you.THiS
WarranTy iS expreSSly in lieu oF all oTHer WarranTieS, expreSS or implied, inCluding
THe WarranTieS oF merCHanTabiliTy and FiTneSS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid.
proof of purchase date and an explanation of the complaint must accompany the merchandise. if our inspection
verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our
expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of
our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 94740
for technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly diAgrAm
8
7
6
3
2
16
3
2
17
1
16
15
5
6
4
7
8
13
14
12
10
9
11
note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 94740
for technical questions, please call 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
|