Garden Lantern
92508
INSTALLATION AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
TO HELP PREVENT SERIOUS INJURY AND ELECTROCUTION,
READ AND UNDERSTAND ALLWARNINGS AND
INSTRUCTIONS BEFORE INSTALLATION OR USE.
©
®
Copyright 2005 by Harbor Freight Tools . All rights reserved. No
portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor FreightTools.
For technical questions and replacement parts, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL SAFETY
4. This light must be installed into an outlet box properly installed and grounded in
accordance with all codes and ordinances. Check with a qualified electrician if
you are in doubt as to whether the outlet is properly grounded. If the light should
electrically malfunction or break down, grounding provides a low resistance path to
carry electricity away from the user.
5. During installation, avoid body contact with grounded surfaces such as pipes,
radiators, ranges, and refrigerators. There is an increased risk of electric shock if
your body is grounded.
6. Do not expose open power outlets or wires to rain or wet conditions. Work only
on a dry day with no chance of rain, and finish all work and seal the Base (1) of the
lantern BEFORE leaving the work area.
7. Do not abuse the power lines. Never use the power lines to hold the lantern
during installation. Keep the power lines away from heat, oil, sharp edges, or
moving parts. Replace damaged power lines immediately. Damaged power lines
increase the risk of electric shock.
8. Always disconnect the electrical circuit before performing any installation, inter-
nal inspection, or maintenance procedures.
9. Use the plastic hook on the Mounting Bracket (8) or other practical ways to se-
cure and support the lantern to the outlet during installation. Holding the lantern
by hand or allowing the lantern to hang on the wires is dangerous and may damage
the wiring, leading to electric shock or fire.
PERSONAL SAFETY
10. Stay alert. Watch what you are doing, and use common sense during installa-
tion. Do not attempt to install this item while tired or under the influence of drugs,
alcohol, or medication. A moment of inattention during installation may result in seri-
ous personal injury.
11. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep
your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or
long hair can be caught in moving parts during installation.
12. Do not overreach. Keep proper footing and balance at all times. Proper footing
and balance enables better control of any power tools used during installation, if an
unexpected situation arises.
13. Use safety equipment. Always wear eye protection. Dust mask, nonskid safety
shoes, hard hat, or hearing protection must be used for appropriate conditions. Al-
ways wear ANSI approved safety goggles when installing using tools and/or equipment.
14. Do not use the light if the Power Switch does not turn it on or off. Any light that
cannot be controlled with the Power Switch is dangerous and must be replaced.
SKU 92508
For technical questions, please call 1-800-444-3353.
PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Maintain light with care. Keep lantern clean. Properly maintained lights will work
better and more efficiently. Do not use a damaged lantern. Tag damaged lanterns and
their corresponding switches “Do not use” until repaired.
16. Check for loose mounting, breakage of parts, and any other condition that may
affect the lantern’s operation. If damaged, have the lantern serviced before use.
Many accidents are caused by poorly maintained fixtures.
SERVICE
17. Fixture service must be performed only by qualified repair personnel. Service or
maintenance performed by unqualified personnel could result in a risk of injury.
18. When servicing a fixture, use only identical replacement parts. Follow instruc-
tions in the “Maintenance Instructions”section of this manual. Use of unauthorized
parts or failure to follow maintenance instructions may create a risk of electric shock or
injury.
19. Maintain labels and nameplates on the Lantern. These carry important information.
If unreadable or missing, contact Harbor Freight Tools for a replacement.
20. Only install type A bulbs rated at or below the maximum wattage (100Watts) for
this Lantern.
21. Do not open the black box inside the Base (1). There are no user-serviceable parts
inside.
SYMBOLOGY
Double Insulated
Canadian Standards
Association
Underwriters
Laboratories, Inc.
Volts Alternating Current
V ~
Amperes
A
n
No Load Revolutions
per Minute (RPM)
o
xxxx/min.
UNPACKING
When unpacking, check to make sure all the parts shown on the Parts List on
the last page are included. If any parts are missing or broken, please call Harbor
Freight Tools at the number shown on the cover of this manual as soon as possible.
SKU 92508
For technical questions, please call 1-800-444-3353.
PAGE 4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTIONS
NOTE: For additional information regarding the parts listed in the following pages, refer to
the Assembly Diagram on the last page.
The power to the outlet box must be disconnected before attempting to
install this item.
If the power is left connected during installation, or if the power comes on
accidentally, SEVERE PERSONAL INJURY or DEATH can occur.
1. BEFORE STARTING THE INSTALLA-
installed on. Visibly label the power
switch leading to the circuit,“Work in
progress on this circuit, DO NOT
TURN POWER ON.”
TION MAKE CERTAIN THAT:
A. All needed tools and materials are
present at the work area. Weather-
proof sealant is not included.
5. Remove the cover from the outlet box.
Use a multimeter, set to a setting appro-
priate for testing 120 VAC, to determine
that the power to the outlet is truly dis-
connected.
B. Sufficient time is allotted for complet-
ing the installation.
C. It is a dry day with no chance of rain.
Leaving the work area without finishing
the installation creates a dangerous situ-
ation, and should be avoided at all costs.
6. Parts 1-7 and 10 are typically preas-
sembled. Remove the Mounting Bracket
(8) if it is attached to the Base (1). Both
Bracket Screws (9) should remain
threaded into the Bracket - see below.
2. This device is installed on an electri-
cal circuit that has sufficient voltage
to SERIOUSLY INJURE or KILL you.
If any doubt exists about your capa-
bility to install this unit safely and
properly, this unit should be installed
by a licensed electrician.
7. Using an Outlet Box Screw (12) through
each slot in the Mounting Bracket (8), sol-
idly attach it to the outlet box.
3. Select an appropriate switch-controlled
outlet box for installation. Having a
switch-controlled outlet allows quick dis-
connection in the event of an emergency.
The lantern’s mounting location:
Figure 1
A. Should be unblocked for optimal illu-
mination and sensor range.
B. Must not block or interfere with any
walkways.
C. Must be out of children’s reach.
4. Disconnect all power connected to
the outlet box that this item is to be
SKU 92508
For technical questions, please call 1-800-444-3353.
PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
8. While being careful not to scrape either
the wall or the lantern, hang the Base
(1) of the lantern on the plastic hookon
the Mounting Bracket (10) by the hole in
the side of the Base - see Figure 1 on
the previous page.
Figure 2
9. The included Wire Nuts (11) may not be
suitable for all applications; ALWAYS
make sure that all connections are se-
cure and, if a wire nut will not tighten
properly, supply one of appropriate size.
Using the wire nuts, carefully attach the
wires in the lantern to the power supply
lines. For each connection, twist the nuts
over both wires clockwise until both
wires are secure. NOTE: If any differ-
ence from these directions is noted
in the color/type of supply lines, have
a licensed electrician finish the instal-
lation. Secure the wires in the order
explained below:
10. Turn the front part of the Mounting
Bracket (8) until the Bracket Screws (9)
are horizontal.
11. Carefully, so as not to pinch any wires
or pull on any connections, slide the
Base (1) off of the plastic hook and onto
the Bracket Screws (9) so that the end
of both Bracket Screws are visible at the
front of the Base.
A. Attach the Black (hot) line to the Black
wire.
12. Thread the Acorn Nuts (10) onto the
ends of the Bracket Screws (9) and
tighten just enough to hold the Base (1).
B. Attach the White (neutral) line to the
white wire.
13. Gently rotate the Base until the lantern
is vertical. A level can be used to en-
sure that the lantern is level.
C. If a Green (ground) line is present,
attach it to the yellow-green wire.
If a Green (ground) line is not present
and the outlet box is a grounded
metal outlet box, then attach the
yellow-green wire to the GND screw
on the Mounting Bracket (8) - see
Figure 1, previous page.
14. Securely tighten the Acorn Nuts (10).
15. Apply weatherproof sealant (not in-
cluded) around the top half of the base
where it meets the wall.
DO NOT APPLY SEALANT TO THE
BOTTOM OF THE BASE.
If a Green (ground) line is not
present and the outlet box is not
grounded, contact a licensed elec-
trician.
The opening at the bottom allows mois-
ture to drain out and helps prevent
moisture from accumulating inside.
Make sure that all connections are se-
cure and that there is no metal showing
on either the Black (hot) or White (neu-
tral) connection before proceeding - see
Figure 2, above right, for an example of
a proper wire nut connection.
16. Install a type A light bulb rated at 100
watts or less, following the instructions
outlined in number three of the Mainte-
nance Instructions.
SKU 92508
For technical questions, please call 1-800-444-3353.
PAGE 6
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
Refer to Figure 3 on the right for the
location of the different settings.
Figure 3
TIME Setting
This controls the amount of time that the
light stays on when the sensor is tripped.
Turn the dial clockwise for more time (up
to 5 minutes) and counterclockwise for less
time (down to one minute).
View from underneath the Base (1).
SENSITIVITY Setting
MODE Settings
TEST
This mode leaves the lantern on con-
stantly and illuminates the red light on
the control panel if the unit detects mo-
tion. This setting is helpful for adjusting
the sensitivity.
This controls the amount of motion
needed to trip the sensor and the distance
that the sensor detects motion at. Keep in
mind that the motion sensor’s range is
approximate and many different factors
can affect the range that this unit detects
motion at.
PHOTO
This mode switches the lantern on when
darkness falls.
Turn the dial clockwise to increase the
sensitivity and counterclockwise to make the
unit less sensitive.
SECURITY
This mode illuminates the lantern for the
duration set by the TIME setting when-
ever the sensor detects motion.
MAINTENANCE INSTRUCTIONS
Shut the unit off at the wall switch before 3. To Change The Bulb:
performing any maintenance, or inspection
procedures, or before changing the light bulb.
A. Shut off the switch and wait until the
lantern has cooled off.
B. Remove the Hood Nut (4) and the
Hood (3).
1. Inspect the unit periodically. Check for
loose mounting, breakage of parts, and
any other condition that may affect the
lantern’s operation. If damaged, have the
lantern serviced before use. Many acci-
dents are caused by poorly maintained
fixtures.
C. Loosen and remove both Nuts (7).
D. Remove both Washers (6) and the
Hood Bracket (5).
E. Using protective gloves, remove the
old bulb and install a new type A bulb
of 100 watts or less.
2. Weekly, wipe the lantern and sensor off
with a damp cloth.
F. Reassemble the lantern securely.
SKU 92508
For technical questions, please call 1-800-444-3353. PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
Part
Description
Q'ty
Part
7
Description
Q'ty
1
2
3
4
5
6
Base
1
6
1
1
1
2
Nut
2
1
2
2
3
1
Window
Hood
8
Mounting Bracket
Bracket Screw
Acorn Nut
9
Hood Nut
Hood Bracket
Washer
10
11
12
Wire Nut
Outlet Box Screw
ASSEMBLY DIAGRAM
NOTE:
Some parts are listed and shown for illustration purposes only, and are not available individu-
ally as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION ORWARRANTY OF ANY KINDTOTHE BUYERTHAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIEDTO REPLACE ANY PARTS OFTHE PRODUCT. IN FACT,THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE
UNDERTAKEN BY CERTIFIED AND LICENSEDTECHNICIANS,AND NOT BYTHE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTSTHERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTSTHERETO.
SKU 92508
For technical questions, please call 1-800-444-3353.
PAGE 8
Download from Www.Somanuals.com. All Manuals Search And Download.
|