®
CUP TYPE OIL FILTER
WRENCH SET
93468
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright © 2005 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Dress properly. Do not wear loose clothing or jewelry as they can be caught
in moving parts. Protective, electrically nonconductive clothes and nonskid
footwear are recommended when working. Wear restrictive hair covering to
contain long hair.
7. Use eye and ear protection. Always wear ANSI approved impact safety
goggles. Wear a full face shield if you are producing metal filings or wood
chips. Wear an ANSI approved dust mask or respirator when working around
metal, wood, and chemical dusts and mists.
8. Do not overreach. Keep proper footing and balance at all times. Do not
reach over or across running machines.
9. Maintain tools with care. Keep tools clean for better and safer performance.
10. Stay alert. Watch what you are doing, use common sense. Do not operate
any tool when you are tired.
11. Check for damaged parts. Before using any tool, any part that appears
damaged should be carefully checked to determine that it will operate
properly and perform its intended function.Check for alignment and binding
of moving parts; any broken parts or mounting fixtures; and any other
condition that may affect proper operation. Any part that is damaged should
be properly repaired or replaced by a qualified technician.
12. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use
accessories intended for use with this tool. Approved accessories are
available from Harbor Freight Tools.
13. Do not operate tool if under the influence of alcohol or drugs. Read
warning labels if taking prescription medicine to determine if your judgment or
reflexes are impaired while taking drugs. If there is any doubt, do not operate
the tool.
14. Maintenance. For your safety, service and maintenance should be
performed regularly by a qualified technician.
Product Specific Safety Precautions
1. Avoid burns from hot oil. Allow vehicle engine to cool down before
removing oil filter. Oil streaming down may splash and strike the head or body
of the operator.
2. Secure vehicle before working underneath. When using vehicle stands to
support the vehicle, make sure that the stands are placed in the correct
position as described in the vehicle maintenance manual, and the emergency
brake is set. Do not rely on a jack to support the vehicle.
SKU 93468
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 3
Warning:The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions and situations that may occur. It
must be understood by the operator that common sense and caution are fac-
tors which cannot be built into this product, but must be supplied by the opera-
tor.
Unpacking
When unpacking, check to make sure the following parts are included. If any parts
are missing or broken, please call Harbor FreightTools at the number on the cover
of this manual.
3/8” Socket
Driver (15)
Oil Filter Cups
Operation
Warning: The vehicle engine must never be started in a closed garage, or any
other sealed structure. Carbon monoxide is produced during operation and is
deadly in a closed environment. Early signs of carbon monoxide poisoning
resemble the flu, with headaches, dizziness, or nausea. If you have any of these
signs get fresh air immediately.
1. Select the appropriate Oil Filter Cup by size specification of the oil filter, and
the number stamped on the Oil Filter Cup.
2. Snap in the 3/8” Socket Driver (15) into the bottom of the selected Oil Filter
Cup.
3. Snap in the other end of the 3/8” Socket Driver (15) into the 1/2” socket
wrench (not supplied).
4. Press the Oil Filter Cup over the Oil Filter
as far as it will go.
5. Place an oil pan, or other oil recovery
devise, under the oil filter to catch the
draining oil.
6. Turn socket wrench counterclockwise until oil filter is removed.
7. Install a new oil filter by first lubricating the new filter gasket, then hand-screw
the filter in place until tight.
SKU 93468
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 4
Caution: Always dispose of used oil properly.
Contact your local HazardousWaste Authority for proper disposal guidelines.
Maintenance
1. Thoroughly clean the Oil Filter Cups before storing.
2. Store all Oil Filter Cups and 3/8” Socket Driver (15) back in the Molded Case
(16) when finished.
Parts List
Item
1.
2.
3.
4.
5.
6.
7.
8.
Description
Cup, 65 mm x 14 *
Cup,65/67 mm x 14
Cup,68 mm x 14
Cup, 73 mm x 14
Cup, 74/76 mm x 15
Cup, 76 mm x 14
Cup, 76 mm x 30
Cup, 75/77 mm x 15
Cup, 80 mm x 15
Cup, 80/82 mm x 15
Cup, 90 mm x 15
Cup, 93 mm x 15
Cup, 93 mm x 36
Cup, 100 mm x 15
3/8” Socket Driver
Case, Blow Mold
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
9.
10.
11.
12.
13.
14.
15.
16.
* (# of Flutes in cup)
NOTE: Some parts are listed and shown for illustration purposes only
and are not available individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST IN
THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE
BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR
THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT,
THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS
AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK
AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT
OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
SKU 93468
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 5
|