ADIRONDACK CHAIR
90849
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright © 2003 by Harbor FreightTools®. All rights reserved.No portion of this manual or
any artwork contained herein may be reproduced in any shape or form without the express
written consent of Harbor FreightTools.
For technical questions and replacement parts, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Use eye and ear protection. Always wear ANSI approved impact safety
goggles during assembly.Wear a full face shield if you are producing wood
chips.Wear an ANSI approved dust mask or respirator when working around
wood, and chemical dusts and mists.
9. Take caution as some woods contain preservatives such as copper
chromium arsenate (CCA) which can be toxic. When cutting these
materials extra care should be taken to avoid inhalation and minimize skin
contact.
10. Check for damaged parts. Before using this chair, any part that appears
damaged should be carefully checked to determine that it will operate properly
and perform its intended function. Any part that is damaged should be properly
repaired or replaced.
11. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use
accessories intended for use with this item. Approved accessories are
available from Harbor FreightTools.
12. Do not assemble this chair if under the influence of alcohol or drugs.
Read warning labels on prescriptions to determine if your judgment or reflexes
are impaired while taking drugs. If there is any doubt, do not proceed with
assembly.
13. Maintenance. For your safety, service and maintenance should be performed
regularly. Check the alignment of all parts, and check the tightness of all
fasteners.
Warning: The warnings, cautions, and instructions discussed in this
instruction manual cannot cover all possible conditions and situations
that may occur. It must be understood by the operator that common
sense and caution are factors which cannot be built into this product,
but must be supplied by the operator.
Unpacking
When unpacking, check to make sure the following parts are included.
1 Back
1 Front Support
1 Seat
14 Wood Screws
2 Front Legs
2 Back Supports
2 Arms
10 55mm Bolts with nut and washer
2 65mm Bolts with nut and washer
1 Owner’s Manual
If any parts are missing or broken, please call Harbor FreightTools at the number
on the cover of this manual, or contact your local Harbor Freight retailer.
SKU 90849
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Carefully unpack the parts and check for damaged or missing parts.
1. Attach Left Front Leg (C1) and Right Front Leg (C2) to Seat (B) using 3 Bolts (H)
per side. Use the included washers and nuts to tighten.
2. Attach both Back Supports (D) to the inner sides of the Seat (B) using 2 Bolts
(H) per side.Tighten using the included washers and nuts.
3. Attach the Left Arm (E1) and Right Arm (E2) to the Front Legs (C1, C2) using 2
Wood Screws (G) per side. Attach the Arms (E1, E2) to the Back Supports (D)
using 1 Long Bolt (I) per side.Tighten the bolts using included washers and nuts.
4. Attach the Back (A) to Seat (B) and Back Supports (D) using a total of 6 Wood
Screws (G).
5. Attach the Front Support (F) to the Front Legs (C1, C2) using 2 Wood Screws (G)
per side.
6. Recheck the alignment of all parts, and recheck the tightness of all fasteners.
7. Set up the chair on a flat, level location. Do not exceed load capacity of 250 lbs.
Maintenance
1. This chair is made of natural Fir wood.This beautiful material will naturally
weather over time, especially if used outdoors.You can manage the speed and
extent of this weathering by controlling the environment in which the chair is
used and stored, as well as any coatings you may apply.
2. Leaving the chair outside exposed to weather, especially direct sun, rain and salt
air, will speed the weathering process.This can be slowed by removing the chair
from these conditions, or covering it with a suitable cover.
3. You may wish to stain, varnish or paint the chair. If so, follow the instructions
supplied with these coatings.
4. Occasionally wash the chair with a garden hose or pressure sprayer to remove
accumulated dust or dirt.Wipe down or blow off any remaining water left on the
chair after washing.
5. Periodically (perhaps once per year), recheck the tightness of all fasteners.
Normal usage of the chair and weathering of the wood may cause fasteners to
loosen.
SKU 90849
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Drawing
SKU 90849
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
Back
Seat
Left Front Leg
Right Front Leg
Back Support
Left Arm
Right Arm
Front Support
Wood Screws
55mm Bolt
65mm Bolt
with Washer and Nut
with Washer and Nut
NOTE: Some parts are listed and shown for illustration purposes only and are not
available individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE
BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR
THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT,
THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THat ALL REPAIRS
AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LI-
CENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK
AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT
OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLA-
TION OF REPLACEMENT PARTS THERETO.
SKU 90849
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
|