electric clipper
Model 47082
Set up and Operating inStructiOnS
read this material before using this product.
Failure to do so can result in serious injury.
SaVe thiS Manual.
©
®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools. Diagrams
within this manual may not be drawn proportionally. Due to continuing improve-
ments, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 09k
Download from Www.Somanuals.com. All Manuals Search And Download.
5. keep the cord away from heated surfaces.
6. never operate the appliance with the air openings blocked. Keep the air
openings free of lint, hair, and the like.
7. never drop or insert any object into any opening.
8. do not use outdoors or operate where aerosol (spray) products are being
used or where oxygen is being administered.
9. do not use this appliance with a damaged or broken comb.
10. to reduce the risk of electric shock, the clipper is equipped with a polarized
plug (one blade is wider than the other). This plug will only fit into the polarized
outlet one way. In the event the plug does not fit fully into the outlet, reverse
the plug. If the plug still will not fit the outlet, have a proper outlet installed by a
qualified electrician. Do not change the plug in any way.
general Safety rules
1. do not abuse the power cord. Never use the Power Cord to carry the clippers
or pull the Plug from an outlet. Keep the Power Cord away from heat, oil, sharp
edges, or moving parts. Replace damaged Power Cords immediately. Damaged
Power Cords increase the risk of electric shock.
2. Stay alert. Do not use while tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating this appliance can result in
serious personal injury.
3. avoid accidental starting. Be sure the Power Switch is off before plugging in.
4. disconnect the power cord plug from the power source before making any
adjustments, changing accessories, or storing the clipper. Such preventive
safety measures reduce the risk of starting the clipper accidentally. Always unplug
the clipper from its electrical outlet before performing any inspection, maintenance,
or cleaning procedures.
5. Store idle clippers out of reach of children and other untrained persons.
Clippers are dangerous in the hands of untrained users.
6. this product is intended for household use only.
7. Maintain labels and nameplates on the clipper. These carry important
information. If unreadable or missing, contact Harbor Freight Tools for a
replacement.
8. People with pacemakers should consult their physician(s) before use.
Electromagnetic fields in close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
9. WARNING: Handling the cord on this product will expose you to lead, a chemical
known to the State of California to cause cancer, and birth defects or other
reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.)
reV 09b
For technical questions, please call 1-800-444-3353.
SKU 47082
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
unpacking
When unpacking, check to make sure that the item is intact and undamaged. If
any parts are missing or broken, please call Harbor Freight Tools at the number shown
on the cover of this manual as soon as possible.
OperatiOn inStructiOnS
blade alignment
• The Clipper comes oiled and aligned from the factory. Blades must be realigned
after they have been removed for cleaning or replacement.
1. To realign blades, match the upper and lower blades teeth up, point for point. The
end of the top blade teeth should be approximately 1.2mm (just under 1/16”) back
from the bottom blade.
2. If blade alignment is incorrect: add a few drops of oil to the blades, turn the
Clipper on for a few moments, then turn off and unplug. Loosen screws slightly
and readjust. Tighten screws after blade is aligned.
• Blades should be oiled every few haircuts to maintain the Clipper in peak
condition.
• Do not use hair oil, grease, or any solvent on the Clipper. The solvent will
evaporate and leave a residue that can slow down the blade’s motion.
power Screw
• The power screw, located on the side of the Clipper, allows the power level of
the Clipper to be adjusted. The power screw has been pre-set at the factory,
however, if the voltage in your home is low, the Clipper may need to be
readjusted.
1. To adjust, use a screwdriver to turn the power screw clockwise until the arm strikes
the coil. When the arm touches the coil it will begin to make noise.
2. Slowly turn power screw counterclockwise until the noise stops. This is the
maximum power setting.
note: DO NOT remove power screw.
blade lever
• The Blade lever allows the operator to change the closeness setting of the cut
without an additional attachment comb.
• At the top position, the blades will give the closest cut and leave the hair the
shortest. Pushing the lever downward increases the cutting length.
• If hair jams the blades, switch the Blade Lever up and down rapidly to clear the
blades.
For technical questions, please call 1-800-444-3353.
SKU 47082
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
• Before turning the Clipper off, rapidly move the Blade Lever from close cut to
longer cut twice. This will clear trimmings from the Clipper.
cutting hair
Attachment Comb #1 leaves 3mm (1/8 inch) hair length.
Attachment Comb #2 leaves 6mm (1/4 inch) hair length.
Attachment Comb #3 leaves 9mm (3/8 inch) hair length.
Attachment Comb #4 leaves 12mm (1/2 inch) hair length.
• The Comb’s sizes are marked on the outside middle surface. To apply a Comb,
hold it with the teeth upwards and slide it onto and along the Clipper blade until
the front of the comb is seated firmly against the clipper blade.
1. Inspect the Clipper, making sure it is free of oil between the cutting blade teeth.
Turn the unit on to distribute the oil and to make sure it runs smoothly. Wipe off
any excess oil. This should be done after each use. Untwist the power cord to
avoid tangling.
2. For good visibility and easy access, seat the person getting their hair cut with their
head at eye level of the person cutting the hair.
3. Comb hair so it is tangle free and arrange in style desired.
4. Place a towel around the neck and shoulders of the person getting the haircut.
5. Attach Comb #1 or #2
• Leave hair dry to more easily control the amount of hair being cut.
• Cut hair slowly and in short strokes.
• Only cut a little hair at a time, more can be trimmed later if necessary.
• Comb hair frequently back into the intended style.
6. Hold the Clipper, cutting edge up, and begin the haircut starting at the middle of
the base of the neck (see diagram 1).
7. With the Comb teeth pointed upwards, lift the Clipper upwards and outwards
through the hair, trimming a small amount at a time.
8. As you cut, lift the Clipper head towards you while continuing to cut the back area
from the bottom of the neck to the top of the ears.
For technical questions, please call 1-800-444-3353.
SKU 47082
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Change to Comb #3 or #4 and, working upwards, cut the hair on the back and top
of the head (see diagram 2 & diagram 3).
9. Using Comb #3 or #4, cut hair on top of head from back to front, against the
direction in which the hair normally grows. In some cases, this may require
changing direction (see diagram 4).
10. Comb #1 or #2 can be used to achieve very close “crew” cuts.
11. For longer hair, use the provided comb to lift the hair away from the top of the
head. Cut over the comb with the hair lifted to desired length (see diagram 5 &
diagram 6).
12. Use the taper level without an attachment comb for close trimming around the
base and side of the neck, and around the ears.
For technical questions, please call 1-800-444-3353.
SKU 47082
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
13. To cut the sideburns, change Comb to #1 or #2. To produce a clean, straight line
for the sideburns, reverse the Clipper by turning the bottom side upwards (see
diagram 7).
14. Press the Clipper at a right angle to the head, with the tips of the blades lightly
touching the skin and work downwards to obtain a clean, razor-like cut.
15. Comb through hair to check for uneven strands and ensure an even cut.
Short tapered styles
1. Starting with Comb #4, cut from the back of the head to the top of the head. Hold
the attachment comb flat against the head and slowly move the Clippers through
the hair (see diagram 8).
2. Use the same procedure from the lower side of the head to the upper side of the
head (as illustrated).
3. Cut the hair against the direction in which it grows, from the front to the top of the
head, and then level the cut with the sides.
4. To create a “flat top” look, the hair must be cut over the top of a flat comb rather
than with an attachment Comb.
5. Use the closer cutting attachments to taper the hair down to the neckline, as
desired.
inSpectiOn, Maintenance, and cleaning
Make sure the power Switch of the clipper is in its “OFF”
position and that the clipper is unplugged from its electrical
outlet before performing any inspection, maintenance, or cleaning
procedures.
BEFORE EACH USE, inspect the general condition of the clipper. Check for loose
screws, misalignment or binding of moving parts, cracked or broken parts, dam-
aged electrical wiring, and any other condition that may affect its safe operation. If
abnormal noise or vibration occurs, have the problem corrected before further use.
do not use damaged equipment.
For technical questions, please call 1-800-444-3353.
SKU 47082
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
pleaSe read the FOllOWing careFully
the ManuFacturer and/Or diStributOr haS prOVided the partS liSt and
aSSeMbly diagraM in thiS Manual aS a reFerence tOOl Only. neither the
ManuFacturer Or diStributOr MakeS any repreSentatiOn Or Warranty
OF any kind tO the buyer that he Or She iS qualiFied tO Make any repairS
tO the prOduct, Or that he Or She iS qualiFied tO replace any partS OF
the prOduct. in Fact, the ManuFacturer and/Or diStributOr expreSSly
StateS that all repairS and partS replaceMentS ShOuld be undertaken
by certiFied and licenSed technicianS, and nOt by the buyer. the buyer
aSSuMeS all riSk and liability ariSing Out OF hiS Or her repairS tO the
Original prOduct Or replaceMent partS theretO, Or ariSing Out OF hiS
Or her inStallatiOn OF replaceMent partS theretO.
partS liSt & diagraM
record product’s Serial number here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not available
individually as replacement parts.
For technical questions, please call 1-800-444-3353.
SKU 47082
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
|