GRINDER/BUFFER
CABINET
40089
OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright © 2002 by Harbor FreightTools®. All rights reserved. No portion of this manual
or any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
UNPACKING
When unpacking, check to make sure all parts shown on the Parts List (page 4) are included. If any parts are
missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon
as possible.
ASSEMBLY INSTRUCTIONS
NOTE: All parts below refer to the parts listed on page 4 of this manual.
Assembly
1.
To assemble Steel Grinding/Buffing Cabinet with three storage shelves you must first lay out all parts and
hardware on a clean surface.
2.
Identify the Top Shelf (#6), the two Side Panels (#2A, #2B, right and left), the Base (#1), and the
Back Panel (#5).
#9, #8, #7
#2A
#5
#2B
#1
3.
4.
Starting with the Base (#1), fit the side panels over the Base, lining up the holes. Use the Bolt (#9) through
the holes. Secure with Washer (#8) and Nut (#7). Repeat with Side Panels (#2A & #2B). Attach Back Panel
(#5) to Side Panels and Base in the same way.
Slide in Shelves (larger on bottom and graduating up to smallest) (C & D). Secure each shelf with Bolts (#9),
Washers (#8) and Nuts (#7) to Side Panels and Back Panel.
#D
#6
#C
5.
Attach Top (#6) aligning with remaining holes. With Bolt (#9) through the holes, secure with Washer (#8) and
Nut (#7) through front and back of Cabinet.
6.
Choose where you want to place Cabinet permanently. Anchor through holes in Base (#1) with hardware for
cement or wood flooring, depending on where you choose to mount Cabinet so it is secure during Grinding
or Buffing for a strong sturdy work surface. (Hardware not included.)
7.
Attach your Buffer or Grinder through the 6 top mounting holes (3/8” H X 2-3/4” L). Hardware will be
required (not supplied). A non flammable rubber pad (not supplied) for insulation, is recommended between
the Cabinet Top and the Buffer or Grinder. This pad will help reduce vibration.
SKU 40089
PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
PART #
DESCRIPTION
QTY
Base
1
1
Left Side
2A
2B
C
D
5
1
Right Side
1
(larger) Shelf
1
(smaller) Shelf
Back Panel
1
1
Top (with sloted holes)
Nut (10MM)
6
1
7
16
16
16
Washer
8
Bolt (M6 X 1,00MM Round Flat)
9
(#6)
(#5)
(D)
(#2B)
(#7)
(#8)
(#9)
(C)
(#2A)
(#1)
MAINTENANCE
1.
For better and safer performance, keep all parts of this product clean and dry at
all times.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM INTHIS MANUAL
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY
REPRESENTATION ORWARRANTY OF ANY KINDTOTHE BUYERTHAT HE OR SHE IS QUALIFIEDTO
MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY
PARTS OFTHE PRODUCT. IN FACT,THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES
THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABIL-
ITY ARISING OUT OF HIS OR HER REPAIRSTOTHE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTSTHERETO.
SKU 40089
PAGE 4
REV 03/05
Download from Www.Somanuals.com. All Manuals Search And Download.
|