Download from Www.Somanuals.com. All Manuals Search And Download.
General Tool Safety Warnings (cont.)
13. DON’T OVERREACH. Keep proper
Table A: RECOMMENDED MINIMUM WIRE GAUGE
FOR EXTENSION CORDS
footing and balance at all times.
(120 VOLT)
14. MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
EXTENSION CORD
LENGTH
NAMEPLATE
AMPERES
(at full load)
25′
50′ 100′ 150′
15. DISCONNECT TOOLS before servicing;
when changing accessories, such as
blades, bits, cutters, and the like.
0 – 6
18
18
16
14
16
16
16
12
16
14
14
14
12
12
6.1 – 10
10.1 – 12
12.1 – 16
16. REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure switch is in
off position before plugging in.
Do not use.
9. USE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using
an extension cord, be sure to use one heavy
enough to carry the current your product will
draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
Table A shows the correct size to use depending
on cord length and nameplate ampere rating.
If in doubt, use the next heavier gauge.
17. USE RECOMMENDED ACCESSORIES.
Consult the owner’s manual for recommended
accessories. The use of improper accessories
may cause risk of injury to persons.
18. NEVER STAND ON TOOL. Serious injury
could occur if the tool is tipped or if the
cutting tool is unintentionally contacted.
19. CHECK DAMAGED PARTS. Before further use
of the tool, a guard or other part that is damaged
should be carefully checked to determine that
it will operate properly and perform its intended
function – check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting, and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or replaced.
The smaller the gauge number, the heavier the cord.
10. WEAR PROPER APPAREL. Do not wear
loose clothing, gloves, neckties, rings, bracelets,
or other jewelry which may get caught in moving
parts. Nonslip footwear is recommended.
Wear protective hair covering to contain long hair.
11. ALWAYS USE SAFETY GLASSES. Also use
face or dust mask if cutting operation is dusty.
Everyday eyeglasses only have impact resistant
lenses, they are NOT safety glasses.
20. DIRECTION OF FEED. Feed work into
a blade or cutter against the direction of
rotation of the blade or cutter only.
12. SECURE WORK. Use clamps or a vise to hold
work when practical. It’s safer than using your
hand and it frees both hands to operate tool.
21. NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN POWER OFF. Don’t leave tool
until it comes to a complete stop.
Item 60238
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Grounding Instructions
TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING WIRE CONNECTION
READ AND FOLLOW THESE INSTRUCTIONS:
110-120 V~ Grounded Tools: Tools with Three Prong Plugs
1. In the event of a malfunction or breakdown,
grounding provides a path of least resistance for
electric current to reduce the risk of electric shock.
This tool is equipped with an electric cord having an
equipment-grounding conductor and a grounding
plug. The plug must be plugged into a matching
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
6. Repair or replace damaged or worn cord immediately.
Grounding
Pin
2. Do not modify the plug provided – if it will
not fit the outlet, have the proper outlet
installed by a qualified electrician.
125 V~ 3-Prong Plug and Outlet
(for up to 125 V~ and up to 15 A)
3. Improper connection of the equipment-grounding
conductor can result in a risk of electric shock.
The conductor with insulation having an outer
surface that is green with or without yellow
stripes is the equipment-grounding conductor.
If repair or replacement of the electric cord or
plug is necessary, do not connect the equipment-
grounding conductor to a live terminal.
7. This tool is intended for use on a circuit that has
an outlet that looks like the one illustrated above in
125 V~ 3-Prong Plug and Outlet. The tool has a
grounding plug
that looks like the plug illustrated above
in 125 V~ 3-Prong Plug and Outlet.
4. Check with a qualified electrician or service
personnel if the grounding instructions are
not completely understood, or if in doubt as
to whether the tool is properly grounded.
8. The outlet must be properly installed and grounded
in accordance with all codes and ordinances.
9. Do not use an adapter to connect
this tool to a different outlet.
5. Use only 3-wire extension cords that
have 3-prong grounding plugs and 3-pole
receptacles that accept the tool’s plug.
Drill Press Safety Warnings
For Your Own Safety Read Instruction
Manual Before Operating Drill Press
7. The use of accessories or attachments not
recommended by the manufacturer may
result in a risk of injury to persons.
1. Wear eye protection.
8. When servicing use only identical replacement parts.
2. Do not wear gloves, necktie, or loose clothing.
9. Only use safety equipment that has been approved
by an appropriate standards agency. Unapproved
safety equipment may not provide adequate
3. Clamp workpiece or brace against
column to prevent rotation.
protection. Eye protection must be ANSI-approved
and breathing protection must be NIOSH-approved
for the specific hazards in the work area.
4. Use recommended speed for drill
accessory and workpiece material.
5. The included chuck key is specially designed
to be self-ejecting, reducing the risk of ejecting
at high speed. Only use the included chuck
key or an identical replacement key.
10. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication.
A moment of inattention while operating power
tools may result in serious personal injury.
6. DO NOT OPERATE WITH ANY GUARD DISABLED,
DAMAGED, OR REMOVED. Moving guards
must move freely and close instantly.
Page 4
For technical questions, please call 1-800-444-3353.
Item 60238
Download from Www.Somanuals.com. All Manuals Search And Download.
Drill Press Safety Warnings (cont.)
11. Industrial applications must follow OSHA guidelines.
• Crystalline silica from bricks and cement or other
masonry products
• Arsenic and chromium from
12. Maintain labels and nameplates on the tool.
These carry important safety information.
If unreadable or missing, contact
chemically treated lumber
Your risk from these exposures varies,
depending on how often you do this type of work.
To reduce your exposure to these chemicals:
work in a well ventilated area, and
work with approved safety equipment, such
as those dust masks that are specially
designed to filter out microscopic particles.
(California Health & Safety Code § 25249.5, et seq.)
Harbor Freight Tools for a replacement.
13. Avoid unintentional starting.
Prepare to begin work before turning on the tool.
14. To prevent FIRE, do not install a larger
bulb in this item′s bulb holder than
listed in the specifications chart.
17. WARNING: Handling the cord on this product will
expose you to lead, a chemical known to the State
of California to cause cancer, and birth defects or
other reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.)
15. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
16. WARNING: Some dust created by power
sanding, sawing, grinding, drilling, and other
construction activities, contains chemicals
known [to the State of California] to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints
18. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.
Vibration Safety
This tool vibrates during use. Repeated or long-term
exposure to vibration may cause temporary or permanent
physical injury, particularly to the hands, arms and
shoulders. To reduce the risk of vibration-related injury:
2. Do not smoke during use. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.
3. Use tools with the lowest vibration when there
is a choice between different processes.
1. Anyone using vibrating tools regularly or for an
extended period should first be examined by a
doctor and then have regular medical check-ups
to ensure medical problems are not being caused
or worsened from use. Pregnant women or
people who have impaired blood circulation to
the hand, past hand injuries, nervous system
disorders, diabetes, or Raynaud’s Disease should
not use this tool. If you feel any medical or
physical symptoms related to vibration (such as
tingling, numbness, and white or blue fingers),
seek medical advice as soon as possible.
4. Include vibration-free periods each day of work.
5. Grip tool as lightly as possible (while still keeping
safe control of it). Let the tool do the work.
6. To reduce vibration, maintain the tool as
explained in this manual. If any abnormal
vibration occurs, stop use immediately.
SAVE THESE INSTRUCTIONS.
Item 60238
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Electrical Rating
Spindle Speeds
120V~ / 60Hz / 2.4A
760, 1150, 1630, 2180, 3070 RPM
5 Speeds
Table Tilt
45º left and right
Swing
8"
Spindle Stroke
Spindle Taper
Chuck Capacity
Worklight Bulb Size
2"
227541
B16
1/16″ - 1/2″ (13mm)
E14 base, 120V, 15W
Setup - Before Use:
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool off and unplug the tool from its electrical
outlet before performing any procedure in this section.
Note: For additional information regarding the parts listed in the following pages,
refer to the Assembly Diagram near the end of this manual.
Mounting
Secure the tool to a supporting structure before use.
Before assembly, bolt the Base to a flat, level,
solid workbench capable of supporting the
weight of the drill press and any workpieces.
Verify that installation surface has no hidden
utility lines before drilling or driving screws.
Assembly
Column to Base
Column (8)
Bolt (5)
1. Place Column (8) on the Base (1) and align
holes in the Column with holes in the Base.
2. Attach using Bolt (5), Spring Washer (4),
and Washer (3) in each hole through
the Column and into the Base.
Base (1)
Figure A: Column to Base Connection
Page 6
For technical questions, please call 1-800-444-3353.
Item 60238
Download from Www.Somanuals.com. All Manuals Search And Download.
Table Support
1. Loosen the Pivot Lever (51).
2. Slide the Table Support (52) over the Column (8).
Table
Column (8)
3. Tighten the Pivot Lever to secure
the Table Support in place.
Support (52)
Pivot
Lever (51)
Figure B: Installing Table Support
Headstock and Feed Handles
Headstock (42)
1. Loosen the two Set Screws (9) on the
right side of the Headstock (42) so they
will stay clear while installing it.
2. With the help of an assistant, lift the Headstock
above the Column (8), and gently slide it
down the Column as far as it will go.
Set
Screws
(9)
3. Tighten the two Set Screws to secure
the Headstock in place.
4. Thread the Feed Handles (6) into the
Feed Seat (7) and tighten them.
Feed
Handle (6)
Feed
Seat (7)
Figure C: Installing Headstock and Feed Handles
Item 60238
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
Tool Set Up
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool off and unplug the tool from its electrical
outlet before performing any procedure in this section.
TO PREVENT SERIOUS INJURY:
DO NOT OPERATE WITH ANY GUARD DISABLED, DAMAGED, OR REMOVED.
Moving guards must move freely and close instantly.
Table Adjustment
1. Adjust the Table (54) by loosening the
Pivot Lever (51), moving the Table,
and tightening the Pivot Lever.
Table
Support (52)
Column (8)
2. Tilt the Table by loosening the Angle Bolt (56) and
tilting to the required angle.
The angle can be read using the Angle Scale (53).
3. TO ENSURE THAT THE DRILL IS ENTIRELY
PERPENDICULAR TO THE TABLE,
insert a straight round bar (not included)
in the Chuck (72), place a square on the
Table (54) and bring it up to the round bar.
Pivot
Lever (51)
Angle Bolt (56)
Adjust the angle as needed.
under Table
Figure D: Table Adjustment
CAUTION! To prevent injury from unexpected
Table movement, tighten Angle Bolt (56)
and Pivot Lever (51) after adjustment.
Setting a Drilling Depth
Located around the Spindle Feed Shaft is a
Depth Stop Collar (A) with a scale. The collar is
capable of turning about the shaft, and may be
locked in place by a Locking Screw (B).
1. Lower the drill (with the power OFF) so that it
contacts the material and hold in that position.
2. Loosen the locking screw and turn the collar
so that the measurement for the depth of the
hole required is in line with the pointer (C).
Figure E: Drill Depth Adjustment
3. Lock the collar in this position using the locking screw.
Page 8
For technical questions, please call 1-800-444-3353.
Item 60238
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Drill Speed
Before changing the speeds, make sure the
machine is switched OFF and UNPLUGGED.
3. Consult the chart below and position
the Belt (59) on the Pulleys (16, 60)
according to the desired drill speed.
1. Open the pulley cover.
4. When the Belt has been correctly positioned, tighten
it by pushing the Motor away from the Headstock until
the belt deflects by approximately 1/2″ at its center
when using reasonable thumb pressure. Lock this
position in with the Motor Tension Knob (10).
2. Loosen the Motor Tension Knob (10) on the
Headstock (42), and move the Motor (14) towards
the Headstock to relieve tension on the Belt (59).
Deflection
Distance
Lamp
(34)
Figure G: Belt Deflection
Note: If either belt is too long to be properly
tensioned, it must be replaced.
Motor Tension
Knob (10)
Light Bulb (73)
Figure F: Motor Tension Knob location
760 RPM
1150 RPM
1630 RPM
2180 RPM
3070 RPM
Spindle
Motor
Spindle
Motor
Spindle
Motor
Spindle
Motor
Spindle
Motor
Figure H: Drill Speed Table
The table above shows the belt arrangements for given drill speeds.
A full chart is also located on the inside of the pulley cover.
Light Bulb Installation
1. To prevent injury, allow the old
3. Install a new Light Bulb of the same type and rating.
(E14 base, 120V, 15W)
Light Bulb (73) to cool completely first.
2. Remove the old Light Bulb (73) from the
Lamp (34) and dispose of it properly.
WARNING! TO PREVENT SERIOUS INJURY
FROM FIRE: Do not install a different style Light Bulb
or a Light Bulb with a higher wattage rating.
Drill Bit Installation
1. Insert the drill bit into the jaws of the Chuck
approximately 1″, ensuring that the jaws
do not touch the flutes of the drill bit.
2. Before tightening the Chuck, ensure that
the drill bit is centered within the jaws.
3. Tighten the Chuck securely with
the included Chuck Key.
Item 60238
For technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Workpiece and Work Area Set Up
1. Designate a work area that is clean and well-lit.
The work area must not allow access by children
or pets to prevent distraction and injury.
9. FOR SMALL MATERIALS that cannot be clamped
to the table, use a drill press vise. Make sure
the vise is clamped or bolted to the table.
2. Route the power cord along a safe route to reach
the work area without creating a tripping hazard or
exposing the power cord to possible damage. The
power cord must reach the work area with enough
extra length to allow free movement while working.
10. WHEN DRILLING COMPLETELY THROUGH
WOOD, position a piece of scrap wood between the
material and the table to prevent splintering on the
underside of the material as the drill breaks through.
The scrap piece of wood must make contact with
the left side of the column. Securely clamp the
other end of the scrap wood to the table. Also, set
the depth of the drill so that the drill will not come
in contact with the table - or align the table so that
the hole in its center is in line with the drill bit.
3. Secure loose workpieces using a vise or clamps
(not included) to prevent movement while working.
4. There must not be objects, such as utility lines,
nearby that will present a hazard while working.
5. Make sure the table height and position
is set so that the drill travel range is
sufficient for the material to be drilled.
6. Make sure the work is securely clamped.
That is, held in a drill vise, or bolted to the table.
Never hold the material with your bare hands while
drilling. Severe personal injury may be caused if
the material is flung out of the operator’s hand.
7. IF THE MATERIAL IS IRREGULARLY SHAPED and
cannot be laid flat on the table, it should be securely
blocked and clamped. Any tilting, twisting or shifting
will result not only in a roughly drilled hole but also
increases the chances of damage to the drill.
Figure I: Bracing workpiece against column
8. FOR FLAT WORK, lay the piece on to a
wooden base and clamp it down firmly against
the table to prevent it from turning.
Page 10
For technical questions, please call 1-800-444-3353.
Item 60238
Download from Www.Somanuals.com. All Manuals Search And Download.
General Operating Instructions
1. Bring the drill bit down with the Feed Knob to where
the hole is to be drilled.
WARNING! If the drill bit grabs and spins the workpiece,
do not attempt to stop the spinning with your hands.
Step back, and turn the drill press off. Wait for the
spindle to stop turning before dislodging the workpiece.
Make minor workpiece alignment adjustments.
2. Plug the Power Cord into an electrical outlet.
3. Turn the Drill Press on.
5. To prevent accidents, turn off the tool and
disconnect its power supply after use. Clean, then
store the tool indoors out of children’s reach.
4. Pull down on the Feed Knob and slowly
drill the hole into the workpiece.
Item 60238
For technical questions, please call 1-800-444-3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Servicing
Procedures not specifically explained in this manual must
be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool off and unplug the tool from its electrical
outlet before performing any procedure in this section.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise or vibration
occurs, have the problem corrected before further use.
Cleaning, Maintenance, and Lubrication
1. BEFORE EACH USE, inspect the general
2. AFTER USE, wipe external surfaces
condition of the tool. Check for:
of the tool with clean cloth.
• loose hardware,
3.
WARNING! If the supply cord of this
power tool is damaged, it must be replaced
only by a qualified service technician.
• misalignment or binding of moving parts,
• cracked or broken parts,
• damaged electrical wiring, and
• any other condition that may
affect its safe operation.
Belt Inspection and Tensioning
1. Examine belt for cracks, tears in
the backing, and other damage.
2. Replace belt if damaged, following the instructions
under Changing Drill Speed on page 9.
Page 12
For technical questions, please call 1-800-444-3353.
Item 60238
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Possible Causes
Likely Solutions
Tool will not start. 1. Cord not connected.
1. Check that cord is plugged in.
2. No power at outlet.
2. Check power at outlet. If outlet is unpowered,
turn off tool and check circuit breaker.
If breaker is tripped, make sure circuit is right
capacity for tool and circuit has no other loads.
3. Tool’s thermal reset breaker
tripped (if equipped).
3. Turn off tool and allow to cool.
Press reset button on tool.
4. Internal damage or wear. (Carbon
brushes or switch, for example.)
4. Have technician service tool.
Tool operates
slowly.
Extension cord too long or
wire size too small.
Eliminate use of extension cord. If an extension cord
is needed, use one with the proper diameter for its
length and load. See Table A on page 3.
Performance
decreases
over time.
1. Accessory dull or damaged.
1. Keep cutting accessories sharp. Replace as needed.
2. Carbon brushes worn or damaged. 2. Have qualified technician replace brushes.
Excessive noise 1. Internal damage or wear. (Carbon
1. Have technician service tool.
or rattling.
brushes or bearings, for example.)
2. Belt (if equipped) too loose (slipping) 2. Properly tension belt.
or too tight (bearing damage).
Overheating.
1. Forcing machine to work too fast.
2. Accessory dull or damaged.
3. Blocked motor housing vents.
1. Allow machine to work at its own rate.
2. Keep cutting accessories sharp. Replace as needed.
3. Wear ANSI-approved safety goggles and
NIOSH-approved dust mask/respirator while
blowing dust out of motor using compressed air.
4. Motor being strained by long or
small diameter extension cord.
4. Eliminate use of extension cord. If an extension cord
is needed, use one with the proper diameter for
its length and load. See Table A on page 3.
Follow all safety precautions whenever diagnosing or servicing
the tool. Disconnect power supply before service.
Item 60238
For technical questions, please call 1-800-444-3353.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List and Diagram
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Parts List
Part
Description
Qty
1
1
5
3
3
3
1
1
2
1
1
1
1
1
2
1
2
4
1
1
1
1
1
5
4
1
3
1
1
2
2
1
2
1
1
1
1
Part
Description
Qty
1
4
1
1
1
1
2
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
2
1
1
1
1
1
1
1
1
2
3
4
5
6
7
8
9
Base
38 Power Cord
Column Support
Flat Washer 8
Spring Washer 8
Bolt M8×20
Feed Handle
Feed Seat
39 Nut M10
40 Spring Cap
41 Depth Spring
42 Headstock
43 Switch Box
44 Flat Washer 4
45 Bolt M4×12
46 Switch Panel
47 Screw ST2.9×10
48 Switch
Column
Set Screw M8×10
10 Motor Tension Knob
11 Spring
12 Slide Bar
13 Rubber Pad
14 Motor
49 Nut M8
50 Set Screw
51 Pivot Lever
52 Table Support
53 Angle Scale
54 Table
55 Spring Washer 12
56 Angle Bolt M12×25
57 Pointer
58 Pointer Stud
59 V-Belt K-660
60 Spindle Pulley
61 Retaining Ring 22
62 Internal Spindle Sleeve
63 Retaining Ring 40
64 Ball Bearing 6203
65 Retaining Ring 12
66 Ball Bearing 6201
67 Gasket
15 Set Screw M6×10
16 Motor Pulley
17 Bolt M8×16
18 Rubber Pad
19 Nut M4
20 Rubber Ring
21 Pulley Cover
22 Bolt M5×10
23 Flat Washer 5
24 Washer 6
25 Bolt M6×12
26 Wire Clamp
27 Screw M4×8
28 Rubber Ring
29 Knob
30 Screw M6×10
31 Wire Clamp
32 Nut M10
33 Flat Washer 10
34 Lamp
35 Nut M6
36 Switch
37 Switch Panel
68 Spindle Sleeve
69 Bolt M6×25
70 Bracket
71 Spindle
72 Chuck
73 Light Bulb
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
Page 14
For technical questions, please call 1-800-444-3353.
Item 60238
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Diagram
27
26
25
28
29
30
31
24
23
22
59
15
60
32
33
33
39
34
21
16
15
57
61
20
19
38
35
62
39
39
17
27 36
37
39
40
41
42
63
64
18
3
73
47
58
24
64
63
43
44
45
46
48
13
12
14
11
49
50
10
9
8
7
65
66
67
51
52
53
54
55
6
5
56
68
66
4
3
69
70
35
71
2
72
1
Item 60238
For technical questions, please call 1-800-444-3353.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
|