MINI VERTICAL MILLING/
DRILLING MACHINE
44991
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright © 2000 by Harbor Freight Tools®. All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape or
form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Use the right tool for the job. Do not attempt to force a small tool or attachment to
do the work of a larger industrial tool. There are certain applications for which this tool
was designed. Do not modify this tool and do not use this tool for a purpose for which
it was not intended.
7. Dress properly. Do not wear loose clothing or jewelry as they can be caught in
moving parts. Protective, electrically non-conductive clothes and non-skid footwear
are recommended when working. Wear restrictive hair covering to contain long hair.
8. Use eye and ear protection. Always wear ANSI approved impact safety goggles.
Wear a full face shield if you are producing metal filings. Wear an ANSI approved dust
mask or respirator when working around metal and chemical dusts and mists.
9. Do not overreach. Keep proper footing and balance at all times. Do not reach over or
across running machines.
10. Maintain tools with care. Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing accessories. Inspect tool
cords periodically and, if damaged, have them repaired by an authorized technician.
The handles must be kept clean, dry, and free from oil and grease at all times.
11. Disconnect power. Unplug tool when not in use.
12. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches
are removed from the tool or machine work surface before plugging it in.
13. Avoid unintentional starting. Be sure the switch is in the Off position when not in
use and before plugging in.
14. Stay alert. Watch what you are doing, use common sense. Do not operate any tool
when you are tired.
15. Check for damaged parts. Before using any tool, any part that appears damaged
should be carefully checked to determine that it will operate properly and perform its
intended function. Check for alignment and binding of moving parts; any broken parts
or mounting fixtures; and any other condition that may affect proper operation. Any
part that is damaged should be properly repaired or replaced by a qualified
technician. Do not use the tool if any switch does not turn On and Off properly.
16. Guard against electric shock. Prevent body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerator enclosures.
17. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use accessories
intended for use with this tool. Approved accessories are available from Harbor
Freight Tools.
18. Do not operate tool if under the influence of alcohol or drugs. Read warning
labels on prescriptions to determine if your judgment or reflexes are impaired while
taking drugs. If there is any doubt, do not operate the tool.
19. Use proper size and type extension cord. If an extension cord is required, it must be
SKU 44991
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
of the proper size and type to supply the correct current to the tool without heating up.
Otherwise, the extension cord could melt and catch fire, or cause electrical damage to
the tool. This tool requires use of an extension cord of 0 to 10 amps capability (up to
50 feet), with wire size rated at 18 AWG. Longer extension cords require larger size
wire. If you are using the tool outdoors, use an extension cord rated for outdoor use.
(signified by “WA” on the jacket).
21. Maintenance. For your safety, service and maintenance should be performed
regularly by a qualified technician.
Note: Performance of this tool (if powered by line voltage) may vary depending on varia-
tions in local line voltage. Extension cord usage may also affect tool performance.
Warning:The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be under-
stood by the operator that common sense and caution are factors which cannot be
built into this product, but must be supplied by the operator.
Unpacking
When unpacking, check to make sure the following parts and accessories are included.
ITEM
A
DESCRIPTION
Large Wrench
B
13 mm Drill Chuck with Taper Shank
A
C
D
E
Oil Bottle
G
Fixing Pin
G
L - Hex. Wrenches, S: 3, 4, 5, 6
G
F
L
F
Socket Head Wrench, D: 45-52
G
H
I
Double-end Wrenches, 8-10, 14-17, 17-19
B
Chuck Key
Handle
D
C
J
J
T-nut
K
Fuse, 5A (110 VAC)
Draw Bar
K
E
L
I
H
If any parts are missing or broken, please call Harbor Freight Tools at the number on the
cover of this manual as soon as possible.
Installation
1. Place the machine on a level, flat, and heavy work table or bench; sufficient to support
weight and use of product and with sufficient light, and enough side room to allow
movement of the Working Table (#19).
2. Secure the machine to the appropriate table or bench using four hex screws (not
supplied), by screwing them through the base mounting holes.
SKU 44991
Page 4
REV 11/02
Download from Www.Somanuals.com. All Manuals Search And Download.
3. An optional oil pan can be placed under the machine before it is mounted to the table.
4. Before operation, loosen the slide, worktable, and drill-mill spindle. They were locked
for shipping.
5. Remove all packing material and clean machine with nonflammable solvent. Oil the
machine according to the lubrication requirements before running the machine.
Assembly
1. Install the Chuck.
- Thoroughly clean the tapered hole in the Chuck (164) and the Spindle (79) shaft of
all dirt, grease, oil, and protective coatings (paint thinner may be necessary).
- Slide the Chuck onto the Spindle shaft.
- Turn the Chuck sleeve clockwise and open the jaws completely.
- Tap the nose of the Chuck lightly with a piece of wood to securely set the Chuck.
2. If necessary, screw the Handles into the Small Hand Wheels.
3. Check the angle of the Vertical Support (68) for true vertical. Check all bolts for
tightness.
Operation
This Mini Milling/Drilling Machine is capable of machining metal and nonmetallic stock by
cutting, drilling, and milling. It can cut circular surfaces, both inside and out, cones, mill
planes or grooves, and other cutting functions depending on the tools used.
The machine consists of the following main components as shown in the photo below.
Motor (127)
Electrical Box (69)
Vertical Support (68)
Small (fine) Feed Wheel (93)
Balance Mechanism Assy.
Headstock and Spindle Box (49)
Emergency Stop Switch (37)
Speed Control Knob (134)
Limit Block (65)
Connecting Strut (72)
Longitudinal Feed Hand Wheel
Working Table (19)
Saddle (35)
Cross Feed Hand Wheel (5)
Base (1)
SKU 44991
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Checks before Operation
1. Turn on the machine by lifting the cover and pulling out the Emergency Stop Switch
(137).
2. Turn the Speed Control Knob (134) and verify spindle speed changes.
3. Verify that the spindle is rotating clockwise.
4. Operate the Longitudinal Axis (Working Table), Cross Axis (Saddle Seat), and Vertical
Axis (Vertical Support), and verify their proper operation and movement.
Caution: Avoid injury to you or damage to machine. Unplug the power cord from the
electrical outlet before performing any adjustments, tool replacement, or maintenance.
Installation of the Taper Shank Cutter
1. Pull off the Protective Cover (126).
(126)
2. Wipe the spindle sleeve and taper of all dirt and grease.
(A)
3. Unscrew Clamp Bolt (101) and remove Dust Guard
(100).
(G)
4. Place the Taper Shank (B) into the Spindle (79) sleeve.
Cover the Cutter (C) (not included) end with an oil cloth
to protect hands and machinery.
(D)
(101)
(100)
5. Insert the Fixing Pin (accessory D) on the right side of
the Spindle sleeve. Refer to page 4.
(B)
6. Using the #14 open end wrench (accessory G), tighten
(clockwise) the Spindle draw bar (A) to lock in the Taper
Shank Cutter into the Spindle.
7. Pull out the Fixing Pin and replace the Protective Cover.
Note: For illustration
purposes only. Only
Chuck with Taper Shank
Removal of the Taper Shank Cutter
(C)
(164) is included.
1. Pull off the Protective Cover (126).
2. Insert the Fixing Pin (accessory D) on the right side of the Spindle sleeve.
3. Using the #14 open end wrench (accessory G), loosen (counterclockwise) the Spindle
draw bar (A) to unlock the Taper Shank Cutter in the Spindle.
4. Using a plastic hammer, gently tap the Taper Shank (B) until it breaks free.
Place a cushion on the Working Table (19) to protect the assembly if it falls out.
5. Replace the Taper Shank Cutter with the Drill Chuck (or other tool) if desired.
Travel Adjustment
Adjusting the Limit Block (65) can control the travel of the Spindle Box.
1. Loosen Handle (30) attached to the Limit Block (65).
SKU 44991
Page 6
REV 12/04
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Adjust the position of the Limit Block (65) up or down. Refer to the Ruler (67) on the
side of the Vertical Support (68).
3. Tighten the Handle.
Adjusting the Vertical Support Angle
(68)
1. Using the Large Wrench (accessory A),
loosen Lock Nut (70) only enough to allow
movement of the Vertical Support (68).
(70)
Caution:Avoid injury or damaging machine, hold
the Vertical Support in place to keep it from fall-
ing to the left or right during adjustment.
2. Adjust the Vertical Support angle as needed (45 degrees left or right, maximum).
Check Ruler (44) for angle.
3. When the Vertical Support is at the desired angle, tighten Lock Nut (70) again.
Basic Drilling and Milling Procedure
During the following procedure, it may be helpful to refer to the machine photo on page 5.
1. Make desired changes and adjustments to the machine for drilling or milling.
2. Set an appropriate speed for drilling or milling the workpiece.
Use the Speed Control Knob (134) to adjust the Spindle speed. For cutting metal, the
speed range should be between 200 to 2500 RPM. Faster speeds are generally used
when milling softer materials and drilling small holes; And slower speeds for milling
harder material and drilling larger holes.
3. Using a fixture (not supplied) mount the workpiece to the Working Table (19).
4. Adjust the Limit Block (65) height.
This will enable Spindle movement to the desired cut, and disable an over cut which
could damage the workpiece fixture or Work Table.
5. Adjust the Working Table Longitudinal Feed Hand Wheel (X-Axis) and the Cross Feed
(Y-Axis) Hand Wheel (5) into position for milling or drilling.
One step turn of the Hand Wheel moves the Work Table 0.03 mm; one complete turn
moves it 1.5 mm.
6. Remove any tools or obstacles from in and around the Work Table.
7. Turn the machine on. Lift the Emergency Stop Switch (137) cover, and pull button out.
8. If necessary, adjust the Spindle speed with the Speed Control Knob (134).
9. Begin milling or drilling.
Use the Operating Lever (58) to make large adjustments to the Spindle height. For fine
adjustments, use the Fine Feeding Wheel (93). Refer to the ruler on the Vertical
Support to determine drilling or milling depth. Caution: Keep hands and fingers clear
of the working table and workpiece while the machine is in operation.
SKU 44991
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
10. When the drilling or milling is completed, press in on the Emergency Stop Switch and
close its cover.
11. Unplug the line cord from the electrical outlet and clean the machine of all debris.
Maintenance
Caution: Avoid injuries or damage to equipment. Before performing any maintenance
on this machine, unplug the power cord from the electrical outlet.
Lubrication Requirements
1. Using a light oil and clean cloth, after each use, wipe down all metal parts of the
machine to prevent rusting.
2. Using machine lubrication grease, periodically apply to the X-axis feed screw (saddle
seat), Y-axis feed screw (working table), and Z-axis feed gear rack (vertical support).
Periodic General Maintenance
1. Inspect all moving parts for lack of lubrication. If necessary, lubricate as described
above.
2. Using compressed air, blow the machine clean of all foreign material. Wear eye
protection during this operation.
3. Check all adjustment screws, bolts, and handles for tightness.
4. Store cutting tools in a wooden box or other moisture proof package.
5. Cover the machine when not in use.
6. Sharpen cutting tools as soon as they become dull.
7. Always keep the taper shank clean.
8. Store all tools and accessories in a clean and dry location, near the machine.
9. Always use the supplied tools and wrenches to make repairs and adjustments.
PLEASE READTHE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM INTHIS
MANUAL AS A REFERENCETOOL ONLY. NEITHERTHE MANUFACTURER NOR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR
SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTSTHERETO.
SKU 44991
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
4
NOTE: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
REV 03/05
SKU 44991
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
with
REV 11/02
SKU 44991
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Longitudinal (Y) Axis and Cross (X) Axis Assembly Drawing
SKU 44991
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Vertical (Z) Axis Assembly Drawing
SKU 44991
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Spindle and Gear Box Assembly Drawing
SKU 44991
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
|