RECIPROCATING SAW - 4.5 AMP
Model 04095
ASSEMBLY AND OPERATING INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Read this material before using this product.
Failure to do so can result in serious injury.
SaVe THiS manual.
Copyright© 2003 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Manual Revised 02/05
Download from Www.Somanuals.com. All Manuals Search And Download.
prong or modify the plug in any way. Do not use any adapter plugs. Check with
a qualified electrician if you are in doubt as to whether the outlet is properly
grounded. If the tools should electrically malfunction or break down, grounding
provides a low resistance path to carry electricity away from the user.
5.
6.
Double insulated tools are equipped with a polarized plug (one blade is wider
than the other). This plug will fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it still does not fit, contact
a qualified electrician to install a polarized outlet. Do not change the plug in
any way. Double insulation
eliminates the need for the three wire grounded
power cord and grounded power supply system.
Avoid body contact with grounded surfaces such as pipes, radiators, ranges,
and refrigerators. There is an increased risk of electric shock if your body is
grounded.
7.
8.
Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
Do not abuse the Power Cord. Never use the Power Cord to carry the tools
or pull the Plug from an outlet. Keep the Power Cord away from heat, oil,
sharp edges, or moving parts. Replace damaged Power Cords immediately.
Damaged Power Cords increase the risk of electric shock.
9.
When operating a power tool outside, use an outdoor extension cord marked
“W-A” or “W”. These extension cords are rated for outdoor use, and reduce the
risk of electric shock.
PERSONAL SAFETY
10.
Stay alert. Watch what you are doing, and use common sense when operating
a power tool. Do not use a power tool while tired or under the influence of
drugs, alcohol, or medication. A moment of inattention while operating power
tools may result in serious personal injury.
11.
12.
13.
14.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
Avoid accidental starting. Be sure theTrigger is off before plugging in. Carrying
power tools with your finger on theTrigger, or plugging in power tools with theTrigger
on, invites accidents.
Remove adjusting keys or wrenches before turning the power tool on. A
wrench or a key that is left attached to a moving part of the power tool may result
in personal injury.
Do not overreach. Keep proper footing and balance at all times. Proper footing
and balance enables better control of the power tool in unexpected situations.
SKU 4095
For technical questions, please call 1-800-444-3353.
PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
15.
16.
Use safety equipment. Always wear eye protection. Dust mask, nonskid safety
shoes, hard hat, or hearing protection must be used for appropriate conditions.
TOOL USE AND CARE
Use clamps (not included) or other practical ways to secure and support the
workpiece to a stable platform. Holding the work by hand or against your body
is unstable and may lead to loss of control.
17.
18.
19.
Do not force the tool. Use the correct tool for your application. The correct
tool will do the job better and safer at the rate for which it is designed.
Do not use the power tool if theTrigger does not turn it on or off. Any tool that
cannot be controlled with the Trigger is dangerous and must be replaced.
Disconnect the Power Cord Plug from the power source before making any
adjustments, changing accessories, or storing the tool. Such preventive safety
measures reduce the risk of starting the tool accidentally.
20.
21.
Store idle tools out of reach of children and other untrained persons. Tools
are dangerous in the hands of untrained users.
Maintain tools with care. Keep cutting tools sharp and clean. Properly
maintained tools with a sharp cutting edge are less likely to bind and are easier
to control. Do not use a damaged tool. Tag damaged tools “Do not use” until
repaired.
22.
23.
Check for misalignment or binding of moving parts, breakage of parts, and
any other condition that may affect the tool’s operation. If damaged, have
the tool serviced before using. Many accidents are caused by poorly maintained
tools.
Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one tool may become hazardous when
used on another tool.
SERVICE
24.
25.
Tool service must be performed only by qualified repair personnel. Service
or maintenance performed by unqualified personnel could result in a risk of injury.
When servicing a tool,use only identical replacement parts. Follow instructions
in the “Inspection, Maintenance, And Cleaning” section of this manual. Use
of unauthorized parts or failure to follow maintenance instructions may create a risk
of electric shock or injury.
SKU 4095
For technical questions, please call 1-800-444-3353.
PAGE 4
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFIC SAFETY RULES
1.
Hold tool by insulated gripping surfaces when performing an operation where
the cutting tools may contact hidden wiring or its own cord. Contact with a‘live’
wire will make exposed metal parts of the tool ‘live’ and shock the operator.
2.
3.
Industrial applications must follow OSHA requirements.
Maintain labels and nameplates on the Saw. These carry important information.
If unreadable or missing, contact Harbor Freight Tools for a replacement.
4.
Always wear ANSI approved safety impact eye goggles and heavy work gloves
when using the Saw. Using personal safety devices reduce the risk for injury.
Safety impact eye goggles and heavy work gloves are available from Harbor Freight
Tools.
5.
Maintain a safe working environment. Make sure there is adequate surrounding
workspace. Always keep the work area free of obstructions, grease, oil, trash, and
other debris. Do not use a power tool in areas near flammable chemicals, dusts,
and vapors. Do not use this product in a damp or wet location.
6.
7.
8.
When using a handheld power tool, always maintain a firm grip on the tool
with both hands to resist starting torque.
Avoid unintentional starting. Make sure you are prepared to begin work before
turning on the Saw.
Do not force the Saw. This tool will do the work better and safer at the speed and
capacity for which it was designed. Do not force the tool and do not use the tool for
a purpose for which it is not intended.
9.
Always keep the extension cord away from moving parts on the tool.
10.
WARNING! People with pacemakers should consult their physician(s) before
using this product. Electromagnetic fields in close proximity to a heart pacemaker
could cause interference to or failure of the pacemaker.
In addition, people with pacemakers should adhere to the following:
• Avoid operating power tools alone.
• Don’t use a power tool with the Trigger locked on.
• If powered via a power cord be certain that the tool is properly grounded. A ground
fault interrupt (GFCI) system is also a good precaution. This inexpensive device
is a good safety measure because it prevents a sustained electrical shock.
• Properly maintain and inspect all tools before use to avoid electrical shock.
11.
12.
Never lay the tool down until it has come to a complete stop. Moving parts can
grab the surface and pull the tool out of your control.
Never leave the saw unattended when it is plugged into an electrical outlet.
Turn off the tool, and unplug it from its electrical outlet before leaving.
SKU 4095
For technical questions, please call 1-800-444-3353.
PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
13.
14.
Always unplug the Saw from its electrical outlet before performing any
inspection, maintenance, or cleaning procedures.
WARNING! Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities, contain chemicals known (to the State of California)
to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement or other masonry products.
• Arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area,
and work with approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
(California Health & Safety Code 25249.5, et seq.)
15.
16.
Always check the Saw Blade (59, 60) to make sure it does not have missing teeth,
cracks, or is bent. Do not use a damaged Saw Blade.
Check that there is enough space under and behind the workpiece for the
reciprocating Saw Blade (59, 60). Make sure you will not be cutting through any
electrical wires or your workbench.
17.
Never attempt to remove material stuck in the moving parts of the Reciprocating
Saw while the Saw is “ON” or plugged in to its electrical outlet.
18.
19.
Never cut material that is thicker than the length of the Saw Blade (59, 60).
Do not exert side-to-side pressure on the Saw Blade (59, 60) or attempt to cut
curves. Doing so will break the Saw Blade and possibly cause pieces of the blade
to fly outward, causing injury.
SKU 4095
For technical questions, please call 1-800-444-3353.
PAGE 6
Download from Www.Somanuals.com. All Manuals Search And Download.
GROUNDING
WARNING
Improperly connecting the grounding wire can result in the risk of electric shock.
Check with a qualified electrician if you are in doubt as to whether the outlet is
properly grounded. Do not modify the power cord plug provided with the tool. Never
remove the grounding prong from the plug. Do not use the tool if the power cord or
plug is damaged. If damaged, have it repaired by a service facility before use. If the
plug will not fit the outlet, have a proper outlet installed by a qualified electrician.
GROUNDED TOOLS:TOOLS WITH THREE PRONG PLUGS
1. Tools marked with “Grounding Required” have a three wire cord and three prong
grounding plug. The plug must be connected to a properly grounded outlet. If
the tool should electrically malfunction or break down, grounding provides a low
resistance path to carry electricity away from the user, reducing the risk of elec-
tric shock. (See Figure A.)
2. The grounding prong in the plug is connected through the green wire inside the
cord to the grounding system in the tool. The green wire in the cord must be the
only wire connected to the tool’s grounding system and must never be attached
to an electrically “live” terminal. (See Figure A.)
3. Your tool must be plugged into an appropriate outlet, properly installed and
grounded in accordance with all codes and ordinances. The plug and outlet
should look like those in the following illustration. (See Figure A.)
FIGURE A
SKU 4095
For technical questions, please call 1-800-444-3353.
PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
DOUBLE INSULATED TOOLS:TOOLS WITH TWO PRONG PLUGS
4. Tools marked “Double Insulated” do not require grounding. They have a special
double insulation system which satisfies OSHA requirements and complies with
the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard
Association, and the National Electrical Code. (See Figure B.)
5. Double insulated tools may be used in either of the 120 volt outlets shown in the
following illustration. (See Figure B.)
FIGURE B
EXTENSION CORDS
1. Grounded tools require a three wire extension cord. Double Insulated tools can
use either a two or three wire extension cord.
2. As the distance from the supply outlet increases, you must use a heavier gauge
extension cord. Using extension cords with inadequately sized wire causes a
serious drop in voltage, resulting in loss of power and possible tool damage. (See
Figure C, next page.)
3. The smaller the gauge number of the wire, the greater the capacity of the cord.
For example, a 14 gauge cord can carry a higher current than a 16 gauge cord.
(See Figure C.)
4. When using more than one extension cord to make up the total length, make
sure each cord contains at least the minimum wire size required. (See Figure C.)
5. If you are using one extension cord for more than one tool, add the nameplate am-
peres and use the sum to determine the required minimum cord size. (See Figure
C.)
SKU 4095
For technical questions, please call 1-800-444-3353.
PAGE 8
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
7.
If you are using an extension cord outdoors, make sure it is marked with the suf-
fix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.
Make sure your extension cord is properly wired and in good electrical condition.
Always replace a damaged extension cord or have it repaired by a qualified elec-
trician before using it.
8.
Protect your extension cords from sharp objects, excessive heat, and damp or
wet areas.
RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS*
(120 VOLT)
EXTENSION CORD LENGTH
NAMEPLATE
AMPERES
(at full load)
25’
50’
75’
100’
150’
0 – 2.0
2.1 – 3.4
18
18
18
18
18
14
12
18
18
18
16
14
12
10
18
18
16
14
12
10
-
18
16
14
12
10
-
16
14
12
12
-
3.5 – 5.0
5.1 – 7.0
7.1 – 12.0
12.1 – 16.0
16.1 – 20.0
-
-
-
* Based on limiting the line voltage drop to five volts at 150% of the rated amperes.
TABLE C
SYMBOLOGY
Double Insulated
Canadian Standards
Association
Underwriters
Laboratories, Inc.
Volts Alternating Current
V ~
Amperes
A
n
No Load Revolutions
per Minute (RPM)
o
xxxx/min.
SKU 4095
For technical questions, please call 1-800-444-3353.
PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
UNPACKING
When unpacking, check to make sure that the tool is intact and undamaged. If any parts
are missing or broken, please call Harbor Freight Tools at the number shown on the cover
of this manual as soon as possible.
ASSEMBLY AND OPERATING INSTRUCTIONS
NOTE: For additional information regarding the parts listed in the following pages, refer
to the Assembly Diagram on page 14.
WARNING: Always make sure the Power Cord (44) of the Reciprocating Saw is un-
plugged from its electrical outlet prior to making any adjustments to the tool.
To Install A Saw Blade:
1.
Select the Saw Blade (59, 60) best suited for your application. The Wood Blade
(59) has a coarser tooth pitch. The Metal Blade (60) has a finer tooth pitch. Make
sure to use each Blade only for its specified material. (See Figure B.)
2.
3.
4.
With the Hex Key (62), loosen but do not remove the Hex Screw (6B).
(See Figure B.)
Slide the selected Saw Blade (58, 60) teeth down into the Guard Plate (2) as far as
possible.
Then, firmly retighten the Hex Screw (6B) to secure the Saw Blade (59, 60) in place.
(See Figure B.)
WOOD
TRIGGER (37)
HEX SCREW (6B)
SAW
BLADE
(59)
SPEED
CONTROL
(19)
ADJUSTABLE
SHOE PLATE
(1)
TRIGGER
LOCK
GUARD PLATE (2)
HEX KEY (62)
METAL SAW BLADE (60)
POWER CORD (44)
FIGURE B
REV 10/05
SKU 4095
For technical questions, please call 1-800-444-3353.
PAGE 10
Download from Www.Somanuals.com. All Manuals Search And Download.
To Adjust The Depth Of Cut:
1.
To Adjust the depth of cut, loosen but do not remove the two Hex Screws (58) located
on the underside of the Reciprocating Saw. (See Figure C.)
2.
For a deeper cut, slide the Adjustable Shoe Plate (1) close to the Guard Plate (2).
For a shallower cut, slide the Adjustable Shoe Plate further away from the Guard
Plate. (See Figure C.)
3.
Then, retighten the two Hex Screws (58). (See Figure C.)
BOTTOM VIEW
GUARD PLATE (2)
ADJUSTABLE
HEX SCREW
(58)
SHOE PLATE
(1)
FIGURE C
Operating Instructions:
1.
The Reciprocating Saw is equipped with a Trigger Lock mechanism. To operate
the tool for extended periods of time squeeze and hold the Trigger (37), then press
the Trigger Lock. To unlock the Trigger Lock mechanism, squeeze and release the
Trigger once. (See Figure B.)
2.
Before plugging the Reciprocating Saw into its 120 Volt, grounded, electrical outlet
check to make sure the Trigger (37) is not locked in its “ON” position. Press and
release the Trigger once to make sure the Trigger is unlocked and “OFF”.
(See Figure B.)
3.
4.
Plug the Reciprocating Saw into its 120 Volt, grounded, electrical outlet.
NOTE: The Reciprocating Saw has a variable speed setting from 0 to 2300 SPM
(strokes per minute). When cutting softer materials, use a faster speed. When
cutting harder materials, use a slower speed. (See Figure B.)
5.
Hold the Reciprocating Saw firmly with both hands, then squeeze the Trigger (37)
to start the Saw. NOTE: Do not start the Reciprocating Saw if the Saw Blade (59,
60) is in contact with anything before operation. If necessary, lift the Reciprocating
Saw to free the Saw Blade before squeezing the Trigger. (See Figure B.)
6.
7.
If operating the Reciprocating Saw for an extended period of time, you may wish to
lock the Trigger (37) in position as described in Step #1). (See Figure B.)
With the Reciprocating Saw “ON”, place the Saw Blade (59, 60) against the material
to be cut. Press down slightly on the Reciprocating Saw to help it cut.
(See Figure B.)
SKU 4095
For technical questions, please call 1-800-444-3353.
PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
8.
Once the cutting procedure is completed, release pressure on the Trigger (37) to
stop the Reciprocating Saw. If the Trigger Lock was used, squeeze and release the
Trigger once to stop the Saw. Then, unplug the Saw from its electrical outlet.
(See Figure B.)
INSPECTION, MAINTENANCE, AND CLEANING
1.
2.
WARNING! Make sure the Trigger of the Reciprocating Saw is in its “OFF” position
and that the tool is unplugged from its electrical outlet before performing any
inspection, maintenance, or cleaning procedures.
BEFORE EACH USE, inspect the general condition of the Reciprocating Saw. Check
for loose screws, misalignment or binding of moving parts, cracked or broken parts,
damaged electrical wiring, cracked or broken Saw Blades, and any other condition
that may affect its safe operation. If abnormal noise or vibration occurs, have the
problem corrected before further use.
Do not use damaged equipment.
3.
TO CLEAN, use a clean cloth or vacuum to remove all dust and debris from the
Reciprocating Saw. Do not use any solvents.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND
ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANU-
FACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND
TOTHE BUYERTHAT HE OR SHE IS QUALIFIEDTO MAKE ANY REPAIRSTOTHE PRODUCT, OR
THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE
MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS
REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSEDTECHNICIANS, AND
NOT BYTHE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR
HER REPAIRSTOTHE ORIGINAL PRODUCT OR REPLACEMENT PARTSTHERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 4095
For technical questions, please call 1-800-444-3353.
PAGE 12
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
Part
1
Description
Adjustable Shoe Plate
Part
37
Description
Trigger
2
Guard Plate
Rubber Sleeve
Screw
38
Right Body
3
39 ** Washer
40 ** Retaining Washer
4
5
Cover
41
42
43
44
Screw
6A
6B
7
Hex Screw
Power Cord Support
Screw
Hex Screw
Blade Holder
Felt Retainer
Felt Pad
Power Cord
8
44B Cord Guard
45 Racing Plate
46 ** Inducer
8B
9
Shock Absorber
Small Cover Sheet A
Screw
10
11
12
14
15
47
48
Screw
Screw
Retaining Washer
Reciprocating Bar
Sliding Bearing
49 ** Screw
50
Wingshield Ring
51 * Ball Bearing (80018)
52 * Rotor
15B Felt Pad
18
19
20
23
24
26
27
28
29
30
31
32
33
34
35
36
Left Body
53 * Screw
Speed Control
Small Cover Sheet B
Large Washer
Roller Bearing (HKH1216)
Roller
54 * Bearing Cover
55 * Ball Bearing (80200)
57 ** Stator
58
59
60
61
62
63
Screw
Wood Saw Blade (not shown)
Metal Saw Blade (not shown)
Replacement Brushes (not shown)
4MM Hex Key (not shown)
Rotor Assembly (Includes 51-56)
Roller Shaft
Gear Wheel
Washer
Center Column
Machine Head
Carbon Brush
Brush Holder
Screw
*
Only available as part of Rotor Assy. (63)
Stator/Lift Body Assembly
(Includes 18, 46, 39, 40, 49, 57)
64
**
Washer
Only available as part of Stator/Lift Body
Assy. (64)
Screw Nut
NOTE: Some parts are listed and shown for illustration purposes only, and are
not available individually as replacement parts.
REV 10/05
SKU 4095
For technical questions, please call 1-800-444-3353.
PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY DIAGRAM
W
M
RE
4M
REV 10/05
SKU 4095
For technical questions, please call 1-800-444-3353.
PAGE 14
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED 90 DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this product
is free from defects in materials and workmanship for the period of 90 days from the date
of purchase. This warranty does not apply to damage due directly or indirectly, to misuse,
abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity,
improper installation, normal wear and tear, or to lack of maintenance.We shall in no event
be liable for death, injuries to persons or property, or for incidental, contingent, special
or consequential damages arising from the use of our product. Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation
of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the com-
plaint must accompany the merchandise. If our inspection verifies the defect, we will either
repair or replace the product at our election or we may elect to refund the purchase price
if we cannot readily and quickly provide you with a replacement. We will return repaired
products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning
the product.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
REV 09e
SKU 4095
For technical questions, please call 1-800-444-3353.
PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
|