RAINPROOF* COLOR CAMERA
SECURITY SYSTEM
Model 91202
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
©
®
Copyright 2004 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
*Extreme weather and temperature conditions excepted.
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL SAFETY
2.
3.
Grounded tools must be plugged into an outlet properly installed and
grounded in accordance with all codes and ordinances. Never remove the
grounding prong or modify the plug in any way. Do not use any adapter plugs.
Check with a qualified electrician if you are in doubt as to whether the outlet is
properly grounded. If the tools should electrically malfunction or break down,
grounding provides a low resistance path to carry electricity away from the user.
Double insulated tools are equipped with a polarized plug (one blade is
wider than the other). This plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician to install a polarized outlet. Do not change the
plug in any way. Double insulation eliminates the need for the three wire
grounded power cord and grounded power supply system.
4.
5.
Do not abuse the Power Cord. Never use the Power Cord to carry the Adapter
or pull the Adapter from an outlet. Keep the Power Cord away from heat, oil,
sharp edges, or moving parts. Replace damaged Power Cords immediately.
Damaged Power Cords increase the risk of electric shock.
When operating the Security Camera outside, use an outdoor extension
cord marked “W-A” or “W”. These extension cords are rated for outdoor use,
and reduce the risk of electric shock. Also, protect all connections from moisture.
PERSONAL SAFETY
6.
Stay alert. Watch what you are doing, and use common sense when
mounting the Security Camera. Do not use power equipment while tired or
under the influence of drugs, alcohol, or medication. A moment of inattention
may result in serious personal injury.
7.
8.
Do not overreach when mounting the Security Camera. Keep proper footing
and balance at all times. Proper footing and balance enables better control in
unexpected situations.
Wear eye protection when mounting the Security Camera. Make sure to
wear ANSI approved safety impact eye goggles. Dust mask, non-skid safety
shoes, hard hat, or hearing protection must be used for appropriate conditions.
SKU 91202
PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT USE AND CARE
9.
Disconnect the Adapter from the power source before making any adjust-
ments, changing accessories, or storing the Security Camera. Such preven-
tive safety measures reduce the risk of accidents.
10.
11.
Mount the Security Camera so that it and its Cords are out of children’s
reach.
Maintain labels and nameplates on the Security Camera. These carry
important information. If unreadable or missing, contact Harbor Freight Tools for
a replacement.
12.
13.
14.
Maintain this product with care. Keep this product clean and dry for better
performance.
Maintenance: For your safety, service and maintenance should be performed
regularly by a qualified technician.
Check for damaged parts. Before using this product, carefully check that it will
operate properly and perform its intended function. Check for damaged parts
and any other conditions that may affect the safe operation of this product. Re-
place or repair damaged or worn parts immediately.
15.
Use the right product for the job. Do not modify this product, and do not use
this product for a purpose for which it was not intended.
SERVICE
16.
17.
Tool service must be performed only by qualified repair personnel. Service
or maintenance performed by unqualified personnel could result in a risk of injury.
When servicing a tool, use only identical replacement parts. Follow in-
structions in the “Inspection, Maintenance, And Cleaning” section of this
manual. Use of unauthorized parts or failure to follow maintenance instructions
may create a risk of electric shock or injury. Only use accessories intended for
this product.
SKU 91202
PAGE 4
Download from Www.Somanuals.com. All Manuals Search And Download.
GROUNDING
WARNING!
Improperly connecting the grounding wire can result in the risk of electric
shock. Check with a qualified electrician if you are in doubt as to whether the
outlet is properly grounded. Do not modify the power cord plug provided with
the tool. Never remove the grounding prong from the plug. Do not use the
tool if the power cord or plug is damaged. If damaged, have it repaired by
a service facility before use. If the plug will not fit the outlet, have a proper
outlet installed by a qualified electrician.
DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS
1.
2.
The Adapter for the Security Camera is marked “Double Insulated” and does not
require grounding. The Adapter has a special double insulation system which
satisfies OSHA requirements and complies with the applicable standards of
Underwriters Laboratories, Inc., the Canadian Standard Association, and the
National Electrical Code. (See Figure A.)
Double insulated products may be used in either of the 120 volt outlets shown in
the following illustration. (See Figure A.)
FIGURE A
SKU 91202
PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTENSION CORDS
1.
2.
Grounded tools require a three wire extension cord. Double Insulated tools
can use either a two or three wire extension cord.
As the distance from the supply outlet increases, you must use a heavier gauge
extension cord. Using extension cords with inadequately sized wire causes a
serious drop in voltage, resulting in loss of power and possible tool damage.
(See Figure B.)
3.
The smaller the gauge number of the wire, the greater the capacity of the cord.
For example, a 14 gauge cord can carry a higher current than a 16 gauge cord.
(See Figure B.)
4.
5.
If using more than one extension cord to make up the total length, make sure
each cord contains at least the minimum wire size required. (See Figure B.)
If you are using one extension cord for more than one tool, add the nameplate
amperes and use the sum to determine the required minimum cord size.
(See Figure B.)
6.
7.
If you are using an extension cord outdoors, make sure it is marked with the
suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.
Make sure your extension cord is properly wired and in good electrical condition.
Always replace a damaged extension cord or have it repaired by a qualified
electrician before using it.
RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS*
(120 VOLT)
NAMEPLATE
AMPERES
EXTENSION CORD LENGTH
(At Full Load)
25
Feet
18
18
18
18
18
14
12
50
Feet
18
18
18
16
14
12
75
Feet
18
18
16
14
12
10
-
100
Feet
18
16
14
12
10
-
150
Feet
16
14
12
12
-
0 – 2.0
2.1 – 3.4
3.5 – 5.0
5.1 – 7.0
7.1 – 12.0
12.1 – 16.0
16.1 – 20.0
-
-
10
-
* Based on limiting the line voltage drop
to five volts at 150% of the rated amperes.
FIGURE B
SKU 91202
PAGE 6
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLOGY
Double Insulated
Canadian Standards
Association
Underwriters
Laboratories, Inc.
Volts Alternating Current
V ~
A
Amperes
No Load Revolutions
per Minute (RPM)
n
o
xxxx/min.
FIGURE C
SPECIFIC SAFETY RULES
1.
This Camera is Rainproof, however, it is NOT intended for use as an underwater
camera.
a. Make sure to mount the Security Camera where it is protected from
extreme weather and temperature conditions.
b. Make sure to properly seal all connections from moisture.
c. Do not immerse any part of this product in any liquid.
2.
3.
4.
Do not point the Security Camera at the sun or any other bright light source.
Do not attempt to open the sealed parts of the Security Camera housing.
The warnings, precautions, and instructions discussed in this manual cannot
cover all possible conditions and situations that may occur. The operator
must understand that common sense and caution are factors which cannot be built
into this product, but must be supplied by the operator.
UNPACKING
When unpacking, check to make sure all the parts shown on the Parts List on
page 10 are included. If any parts are missing or broken, please call Harbor Freight Tools
at the number shown on the cover of this manual as soon as possible.
SKU 91202
PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY AND OPERATING INSTRUCTIONS
NOTE: For additional information regarding the parts mentioned in the following pages,
refer to the Assembly Diagram on page 10.
1.
Locate the two mounting holes in the base of the Security Camera (1). Then use
the two Wood Screws (4) to mount the Security Camera in the desired location on a
wall or ceiling. Then, adjust the Security Camera to view a specific area.
(See Figure D.)
2.
3.
Connect the Security Camera Phone Jack to the Cable (2). (See Figure D.)
Connect the Audio/Video Output Cables to your television. NOTE: The Yellow
Cable connects to the Yellow (video) television jack. The White Cable connects
to the White (audio) television jack. (See Figure D.)
4.
5.
Plug the Adapter (3) into the nearest 120 volt, grounded, electrical outlet.
(See Figure A.)
Turn on your television, and set the channel selector to “AV Channel”*. The Secu-
rity Camera’s view will then appear on the television screen. Turn up the volume on
the television and the Security Camera’s built-in microphone will relay sound to the
television.
*The video input selector may be a function of the TV remote control.
SECURITY
TELEVISION
CAMERA
(1)
(NOT INCLUDED)
ADAPTER
(3)
CABLE
(2)
PHONE
JACK
AUDIO/VIDEO
OUTPUT CABLES
FIGURE D
SKU 91202
PAGE 8
Download from Www.Somanuals.com. All Manuals Search And Download.
INSPECTION, MAINTENANCE, AND CLEANING
1.
2.
WARNING! Always unplug the Adapter (3) from its electrical outlet prior to
performing any inspection, maintenance, or cleaning procedures.
Before each use, inspect the general condition of the Security Camera. Check
for misalignment or binding of moving parts, cracked or broken parts, damaged
wiring, and any other condition that may affect its safe operation. If a problem
occurs with the Security Camera, have the problem corrected before further use.
Do not use damaged equipment.
3.
4.
To clean, use a clean, damp, cloth to clean the outer surfaces of the Security
Camera. A mild detergent may be used. Do not use solvents. Do not immerse any
part of the Security Camera in liquids.
When storing, always keep the Security Camera in the in a clean, dry location.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS
LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY.
NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION
OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO
MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO
REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSEDTECHNICIANS, AND NOT
BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF
HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT
PARTS THERETO.
SKU 91202
PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST AND ASSEMBLY DIAGRAM
Part #
1
2
Description
Security Camera
Cable (80’)
Qty.
1
1
Part #
3
4
Description
AC/DC Adapter
Wood Screw
Qty.
1
2
1
3
2
4: WOOD SCREWS NOT SHOWN.
NOTE: Some parts are listed and shown for illustration purposes only, and are not
available individually as original or replacement parts.
SKU 91202
PAGE 10
Download from Www.Somanuals.com. All Manuals Search And Download.
|