3
/ ” ROTARY SPOT WELD
8
CUTTER
Model 95343
SET UP AnD OPERATing inSTRUCTiOnS
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE ThiS MAnUAL.
©
®
Copyright 2006 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Manual Revised 10d
Download from Www.Somanuals.com. All Manuals Search And Download.
UnPACKing
inSPECTiOn, MAinTEnAnCE,
AnD CLEAning
When unpacking, check to make sure that the
item is intact and undamaged. If any parts are missing
or broken, please call Harbor Freight Tools at the
number shown on the cover of this manual as soon as
possible.
1.
WARning! Make sure the Power Switch
of the drill is in its “OFF” position and that the
tool is unplugged from its electrical outlet before
performing any inspection, maintenance, or
cleaning procedures.
ATTAChing AnD REMOVing
ThE BiT
2.
BEFORE EACh USE, inspect the general
condition of the tool. Check for loose or broken
parts and any other condition that may affect its
safe operation. If abnormal noise or vibration
occurs, have the problem corrected before
further use. Do not use damaged equipment.
1.
2.
Insert the Shaft into a vise. Grasp the Bit with a
wrench and unscrew the Bit.
Thread on the new Bit or flip to unused cutter
3.
Clean the Spot Weld Cutter after each use.
Remove any debris, grease, oil and dirt. Store in
the Blow Mold Case in a secure place out of the
side.
3.
1.
2.
Remove Shaft and Bit from vise.
reach of children.
OPERATiOn inSTRUCTiOnS
The Spot Weld Cutter is now ready to be
mounted to the drill. Read the drill owner’s
manual for instructions on properly mounting drill
bits.
Before using the Spot Weld Cutter, make certain
that the work piece is firmly clamped and secured
in place. Place the Spot Weld Cutter Bit over
the spot weld and slowly begin drilling into the
work piece. Always hold the drill firmly with both
hands to ensure safe operation of the Spot Weld
Cutter. Note: If Bit does not stay in spot weld
depression, dimple the center of the weld with a
punch (not included).
3.
Drill until the spot weld is removed. Do not over
drill.
note:When working on a vehicle, be certain to protect
all electrical components from damage.
Follow the vehicle owner’s manual for securing
electrical systems. Make certain that the drilling
path is clear of all cables, wires and electrical
components.
a. Disconnect and isolate the negative battery
cable and disarm the passive restraint
system.
b. Protect computer modules, connectors, and
wiring from dirt, heat, moisture and metal chips.
SKU 95343
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LiST
Part Description Quantity
1
2
Shaft
Bit
1
1
ASSEMBLY DiAgRAM
1
2
note:Some parts are listed and shown for illustration purposes only, and are not available individually as
replacement parts.
PLEASE READ ThE FOLLOWing CAREFULLY
THe MANUFACTUReR AND/OR DISTRIBUTOR HAS PROvIDeD THe PARTS LIST AND ASSeMBLY DIAGRAM
IN THIS MANUALASAReFeReNCe TOOL ONLY. NeITHeR THe MANUFACTUReR OR DISTRIBUTOR MAKeS
ANY RePReSeNTATION OR WARRANTY OF ANY KIND TO THe BUYeR THAT He OR SHe IS QUALIFIeD TO
MAKe ANY RePAIRS TO THe PRODUCT, OR THAT He OR SHe IS QUALIFIeD TO RePLACe ANY PARTS
OF THe PRODUCT. IN FACT, THe MANUFACTUReR AND/OR DISTRIBUTOR eXPReSSLY STATeS THAT
ALL RePAIRS AND PARTS RePLACeMeNTS SHOULD Be UNDeRTAKeN BY CeRTIFIeD AND LICeNSeD
TeCHNICIANS, AND NOT BY THe BUYeR. THe BUYeR ASSUMeS ALL RISK AND LIABILITY ARISING OUT
OF HIS OR HeR RePAIRS TO THe ORIGINAL PRODUCT OR RePLACeMeNT PARTS THeReTO, OR ARISING
OUT OF HIS OR HeR INSTALLATION OF RePLACeMeNT PARTS THeReTO.
SKU 95343
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
|