Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual
near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and
the receipt in a safe and dry place for future reference.
ITEM 69054
60" Workbench
email our technical support at: [email protected]
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-800-444-3353 as soon as possible.
©
®
Copyright 2012 by Harbor Freight Tools . All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
Save thiS manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Top Shelf Weight Capacity
250 lb.
Drawer Weight Capacity
Bottom Shelf Capacity
Vise Capacity
25 lb. (per drawer)
200 lb.
7"
Table Top Thickness
2-1/2"
Setup - Before use:
Read the entiRe impORtant SaFetY inFORmatiOn section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
note: For additional information regarding the parts listed in the following
pages, refer to Parts List and Diagram on page 10.
note: More than one person is needed for proper assembly.
note: In the supplied bag of hardware, the Nuts are already threaded onto the Screw (6).
Connecting
Nuts (8)
1. Insert Connecting Nuts (8) into holes at end of Cross Braces (3).
Make sure that the slot on the Nuts align horizontally with the
Bolts (7). This will allow the Bolts to be threaded into the Cross
Braces. See Figure A, right.
Leg (4)
Cross Brace (3)
Figure a
Hex
Wrench (9)
2. Set the Cross Brace against a Leg (4) and use the Hex Wrench
(9) and Bolt (7) to fasten Cross Brace and Leg together.
See Figure B, right.
Cross
Brace (3)
Leg (4)
Figure B
nOte: Make sure the groove in the Cross Brace is facing IN.
See Figures A and B.
Item 69054
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Once both Legs have been fastened to the Cross Brace,
slide the Shelf (2) above against the Legs so that the far
edge fits onto the groove on the Cross Brace.
See Figure C, right.
Cross
Brace (3)
Leg (4)
Shelf (2)
Figure C
4. While your assistant is holding the Shelf in place against the
first Cross Brace, set the second Cross Brace against the
other edge of the Shelf. See Figure D, right.
Figure 4
Shelf (2)
Cross
Brace (3)
Figure D
5. Once the Cross Brace is in place and the mounting holes on
the Legs are aligned with the Connecting Nuts in the Cross
Brace, use the Hex Wrench and Bolts to fasten the second
Cross Brace to Legs.
With your assistant’s help, place the Table Top (1) face down
on a smooth, padded surface. This will allow you to install
the sliding drawers.
note: When setting down the assembled Legs onto the Table
Top, verify both Legs and Table Top are facing the correct
direction. (Note the small “Front” labels placed on the items.
These labels can be removed after assembly.)
See Figure E, right.
Figure e
Page 4
For technical questions, please call 1-800-444-3353.
Item 69054
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Set the Sliding Partition (14) into place by inserting the tabs at the end of the Partition into the holes at the center
of the Table Top’s underside. See Figure F, right.
Sliding
Partition (14)
Table
Top (1)
Figure F
note: Verify that the Sliding Partition and Table Top face the
same direction. See Figure G, right.
Sliding Partition (14)
Table
Top (1)
Figure G
7. Use the Screws (13) to fasten the Sliding Partition to the
middle of the Table Top’s underside. See Figure H, right.
note: There are no pilot holes available for this step, so you will
need to use a drill to make the pilot holes before threading
in Screws.
Sliding
Partition (14)
Table
Top (1)
8. Using assistance, set the assembled Legs and
Shelf onto the underside of the Table Top.
Figure h
note: Verify that the Drawer guide slots on the Sliding Partition face
the same way as the Drawer guide slots on the Legs.
Item 69054
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Use the Hex Wrench and Screws (6) to fasten the tops of the
Legs to the Table Top underside. See Figure I, right.
Leg (4)
Hex
Wrench
(9)
Table
Top (1)
Figure i
10. Use the Hex Wrench and Screws (13) to fasten the sides of
the Legs to the Table Top underside. See Figure J, right.
Leg (4)
note: There are no pilot holes available for this step, so you
will need to use a drill to make the pilot holes before threading
in Screws.
Table
Top (1)
Figure J
11. Set the Lower Support (15) across the top of the Sliding
Partition and against the sides of the Legs. Then use
Screws (6) to fasten each end of the Lower Support to the
sides of the Legs. See Figure K, right.
Lower
Support
(15)
Screws (6)
Leg (4)
Figure K
Page 6
For technical questions, please call 1-800-444-3353.
Item 69054
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Once the ends of the Lower Support have been fastened to
the Legs, use the Screws (6) to fasten the middle of the
Lower Support to the top of the Sliding Partition.
See Figure L, right.
Sliding
Partition (14)
Lower
Support
(15)
13. With assistance, set the assembled frame right-side up and
in the spot where you want the Workbench located.
Figure l
14. Remove the Vise Screw and Washer (12) from the middle
thread of the Vise (5). See Figure M, right.
Vise (5)
Vise Screw/
Washer
(12)
Figure m
15. Once the Vise Screw and Washer are removed, slide the
Vise into the three holes on the side of the Workbench.
Once the Vise is threaded into the holes halfway, use the
Hex Wrench to tighten the screws on either side of the
Vise’s center thread. See Figure N, right.
Hex
Wrench
(3)
16. Use the Vise handle to thread in the Vise all the way and re-
install the Vise Screw and Washer. This will keep the Vise
locked on place on the side of the Workbench.
Vise (5)
Figure n
Item 69054
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
17. Use the Drawer Screws (22) to fasten the Drawer Handles
(21) to the Drawer Front Panels (16). See Figure O, right.
Drawer Front
Panel (16)
note: Each Drawer piece should have a sticker designating what it
is (P1-P5). Use the Parts List as on page 10 as reference. This
will help assure correct assembly.
Drawer Handle
(21)
Figure O
Drawer Slot
Panel (19)
18. Fasten the Drawer Panel (18) and the Drawer Slot
Panel (19) to the Drawer Front Panel.
See Figure P, right.
Drawer Front
Panel (16)
Screwdriver
Figure p
19. Fasten the Drawer Back Panel to the ends of the two side
Panels. Then slide the Drawer Bottom (20) into the
grooves along the insides of the side panels, making sure
the felt side is up. See Figure Q, right.
Drawer Bottom
(20)
Drawer Back
Panel (17)
Drawer Slot
Panel (19)
Figure Q
Page 8
For technical questions, please call 1-800-444-3353.
Item 69054
Download from Www.Somanuals.com. All Manuals Search And Download.
20. Fasten Drawer Bottom to Drawer Pack Panel. Once
Drawers are fully assembled, verify that the inside tracks
along the Sliding Partition are pushed forward.
See Figure R, right.
Figure R
21. Slide Drawers into tracks along Sliding Partition and insides
of the Legs. See Figure S, right.
Drawer Front
Panel (16)
Figure S
22. Once all Drawers are inserted, tap Wood Pegs (10) and
Small Anvil Pegs (11) into desired holes on the Table Top.
See Figure T, right.
Wood Pegs (10)
The Workbench is now fully assembled and ready for use.
Small Anvil
Pegs (11)
Table
Top (1)
Figure t
Item 69054
For technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
parts list and Diagram
pleaSe ReaD the FOllOWinG CaReFullY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLy DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLy. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANy REPRESENTATION OR WARRANTy OF ANy KIND TO THE BUyER THAT HE OR SHE IS
QUALIFIED TO MAKE ANy REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANy PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR ExPRESSLy
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN By CERTIFIED AND
LICENSED TECHNICIANS, AND NOT By THE BUyER. THE BUyER ASSUMES ALL RISK AND LIABILITy
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
parts list
part
Description
Qty
1
1
2
2
1
6
8
8
part
Description
Qty
1
58
1
1
4
4
4
4
4
1
2
3
4
5
6
7
8
9
Table Top
Shelf
12 Vise Screw and Washer
13 Screw
Cross Brace
Leg
14 Sliding Partition
15 Lower Support
Vise
16 Drawer Front Panel (P1)
17 Drawer Back Panel (P2)
18 Drawer Panel (P3)
19 Drawer Slot Panel (P4)
20 Drawer Bottom (P5)
21 Drawer Handle
Screw (50mm)
Bolt (60mm)
Connecting Nut
Hex Wrench (50mm)
1
4
4
10 Wood Peg
11 Anvil Peg
4
8
22 Drawer Screw
11
10
5
1
21
16
15
4
2
3
Page 10
For technical questions, please call 1-800-444-3353.
Item 69054
Download from Www.Somanuals.com. All Manuals Search And Download.
assembly Diagram
Shelf (2)
Table Top (1)
Cross Brace (3)
Vise (5)
Leg (4)
Screw (50mm) (6)
Bolt (60mm) (7)
Connecting
Hex Wrench (50 mm) (9)
Nut (8)
Screw and Washer
(Washer not shown) (12)
Wood Peg (10)
Anvil Peg (11)
Lower Support (15)
Screw (13)
Sliding Partition (14)
Drawer Screws (22)
Drawer Back Panel - p2 (17)
Drawer Panel - p3 (18)
Drawer Slot Panel - P4 (19)
Drawer Bottom - p5 (20)
Drawer Front Panel - p1 (16)
Drawer Handle (21)
Record product’s Serial number here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
Item 69054
For technical questions, please call 1-800-444-3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTy IS ExPRESSLy IN LIEU OF ALL OTHER
WARRANTIES, ExPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITy AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
|