Bicycle RePAiR STAND
WiTH TOOl TRAy
Model 98579
SeT uP AND OPeRATiNg iNSTRucTiONS
Read this material before using this product.
Failure to do so can result in serious injury.
SAVe THiS MANuAl.
©
®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
cover Revised 09l
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Only use the Stand on a flat, dry, level
surface capable of supporting the weight
of the Stand and its load.
8. Do not exceed the Stand’s maximum
load capacity of 66 pounds. Beware of
dynamic loading! Suddenly dropping
load may create for a brief instance an
excess load which may result in personal
injury and/or property damage.
9. Do not move the Stand with a load
attached. The Stand could tip over,
resulting in personal injury and/or
property damage.
10. Do not allow anyone to sit or stand on
this Stand.
11. Do not leave the Stand unattended when
it is under a load. Remove the load
before leaving. Do not use to support
loads for extended periods of time.
12. The warnings and instructions discussed
in instruction manual cannot cover
all possible conditions and situations
that may occur. It must be understood
by operator that common sense and
caution are factors which cannot be built
into product, but must be supplied by
operator.
SAVe THeSe
iNSTRucTiONS.
SKU 98579
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
BOlT (8)
FiguRe B
SPeciFicATiONS
Weight Capacity 66 lb.
Bicycle Capacity
Dimensions
1
24-3/4” L x 37-1/2” W x 41-1/2” H
leg (5)
HeAD BAR (6)
NuT (9)
2. Attach the Head Bar (6) to end of the Leg
(5), using two Bolts (8) and two Nuts (9).
Repeat this procedure for the remaining
Head Bar and Leg. (See Figure B.)
uNPAckiNg
When unpacking, make sure that the
item is intact and undamaged. If any parts
are missing or broken, please call Harbor
Freight Tools at 1-800-444-3353 as soon as
possible.
FiguRe c
NuT (9)
BOlT (8)
TOP
SADDle (21)
ASSeMBly iNSTRucTiONS
Read the eNTiRe iMPORTANT
SAFeTy iNFORMATiON section at
the beginning of manual including
all text under subheadings therein
before set up or use of this
product.
HeAD
BAR (6)
3. Attach the Top Saddle (21) to both ends
of the Head Bars (6), using four Bolts (8)
and four Nuts (9). (See Figure c.)
Note: For additional information regarding the
parts listed in following pages, refer to
Assembly Diagram near end of manual.
leg (5)
FOOT (2)
BOlT (8)
SOckeT
kNOB
HeAD
NuT (11)
ScReW (12)
FiguRe A
NuT (9)
1. Attach the Leg (5) to the Foot (2), using
two Bolts (8) and two Nuts (9). Repeat
this procedure for the remaining Leg and
Foot. (See Figure A.)
FiguRe D
4. Attach the Connector (23) to the upper
portions of the two Head Bars (6) using
one Bolt (8), one Nut (9), one Knob Nut
(11), and one Socket Head Screw (12).
(See Figure D.)
Page 4
For technical questions, please call 1-800-444-3353.
SKU 98579
Download from Www.Somanuals.com. All Manuals Search And Download.
FiguRe H
cONNecTOR
(23)
kNOB
BOlT (16)
PROTecTOR
(22)
HeAD
BAR (6)
BOlT (8)
NuT (9)
FiguRe e
5. Attach the Protector (22) to the
crossbeam of the Head Bar (6), using
one Bolt (8) and one Nut (9). Repeat this
procedure for the remaining Protector
and Head Bar. (See Figure e.)
BRAke cAP (24)
8. Secure the Mounting Curve (10) in
position, using one Knob Bolt (16) and
one Brake Cap (24). (See Figure H.)
FiguRe i
MOuNTiNg
cuRVe (10)
kNOB
BOlT (16)
FiguRe F
MOuNTiNg
cuRVe (10)
ScReWS (17)
FRONT WHeel
STABilizeRS (15)
ADjuSTABle
SADDle (18)
6. Attach the Adjustable Saddle (18) to the
Mounting Curve (10), using two Screws
(17). (See Figure F.)
kNOB
NuT (11)
9. Attach the two Front Wheel Stabilizers
(15) to the Mounting Curve (10), using
one Knob Nut (11) and one Knob Bolt
(16). (See Figure i.)
FiguRe g
MOuNTiNg
cuRVe (10)
7. Position the Mounting Curve (10) as
shown. (See Figure g.)
SKU 98579
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
HOOk
FiguRe l
clAMP (19)
MOuNTiNg
cuRVe (10)
SPRiNg
(14)
FiguRe j
SPRiNg (14)
SPAceR
(13)
SOckeT HeAD
ScReW (12)
10. Attach the Spring (14) to the Mounting
Curve (10), using one Socket Head
Screw (12) and one Spacer (13).
(See Figure j.)
12. Insert the end of the Spring (14) into the
hole in the Hook Clamp (19).
(See Figure l.)
HOOk
clAMP (19)
FiguRe k
HeAD BAR
HeAD BAR
(6)
(6)
FiguRe M
clAMP
kNOB (7)
MOuNTiNg
cuRVe (10)
TRAy (25)
13. Attach the Tray (25) to the two Head
11. Attach the Hook Clamp (19) to the
Mounting Curve (10). Attach the Clamp
Knob (7) to the Hook Clamp.
(See Figure k.)
Bars (6) as shown. (See Figure M.)
Page 6
For technical questions, please call 1-800-444-3353.
SKU 98579
Download from Www.Somanuals.com. All Manuals Search And Download.
OPeRATiNg iNSTRucTiONS
FiguRe O
Read the eNTiRe iMPORTANT
SAFeTy iNFORMATiON
section at the beginning of this
manual including all text under
subheadings therein before set up
or use of this product.
kNOB
BOlT (16)
1. Locate the Stand on a clean, dry, flat,
and level surface capable of supporting
the weight of the Stand, bicycle, bicycle
parts, tools, etc.
4. To swivel the bicycle upward or
downward loosen the Knob Bolt (16).
Move the bicycle to the desired position.
Then retighten the Knob Bolt.
(See Figure O.)
TOP
ADjuSTABle
SADDle (21)
SADDle (18)
5. When finished repairing the bicycle,
loosen the Clamp Knob (7) and remove
the Hook Clamp (19) from the bicycle
frame. With assistance, remove the
bicycle from the Stand. (See Figure k.)
FiguRe N
6. Store the Stand in a clean, dry, and safe
location out of reach of children and
other unauthorized persons.
2. With assistance, set the bicycle on the
Stand, making sure the frame of the
bicycle is resting on the Adjustable
Saddle (18) and Top Saddle (21). Then
adjust the Clamp Knob (7) so that the
Hook Clamp (19) fits tightly over the
bicycle frame. (See Figures N and O.)
3. Swing the two Front Wheel Stabilizers
(15) next to the front wheel of the bicycle
to limit its movement while you work on
the bicycle.
ReV 09l
SKU 98579
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
MAiNTeNANce AND
SeRViciNg
PleASe ReAD THe
FOllOWiNg cAReFully
THE MANUFACTURER AND/OR DISTRIBUTOR
HAS PROvIDED THE PARTS LIST AND ASSEMBLY
DIAgRAM IN THIS MANUAL AS A REFERENCE
TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION
OR WARRANTY OF ANY KIND TO THE BUYER
THAT HE OR SHE IS qUALIFIED TO MAKE ANY
REPAIRS TO THE PRODUCT, OR THAT HE OR SHE
IS qUALIFIED TO REPLACE ANY PARTS OF THE
PRODUCT. IN FACT, THE MANUFACTURER AND/
OR DISTRIBUTOR ExPRESSLY STATES THAT ALL
REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS, AND NOT BY THE BUYER. THE
BUYER ASSUMES ALL RISK AND LIABILITY ARISINg
OUT OF HIS OR HER REPAIRS TO THE ORIgINAL
PRODUCT OR REPLACEMENT PARTS THERETO,
OR ARISINg OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
Procedures not specifically
explained in this manual must
be performed only by a qualified
technician.
TO PReVeNT
SeRiOuS iNjuRy
FROM AcciDeNTAl
OPeRATiON:
Remove any load from the Stand
before performing any
inspection, maintenance, or
cleaning procedures.
1. BEFORE EACH USE, inspect the
general condition of the Stand. Check
for loose screws, misalignment or
binding of moving parts, cracked or
broken parts, and any other condition
that may affect its safe operation.
Record Product’s Serial Number Here:
__________________________________
Note: If product has no serial number, record
2. PERIODICALLY: Lubricate all moving
parts with a light grease or machine oil.
month and year of purchase instead.
Note: Some parts are listed and shown for
illustration purposes only, and are not
available individually as replacement
parts.
3. AFTER USE, clean external surfaces
of the Stand with clean cloth and mild
detergent. Do not use solvents.
4. Store the Stand in a clean, dry, safe
location out of reach of children and
other unauthorized persons.
Page 8
For technical questions, please call 1-800-444-3353.
SKU 98579
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS liST & ASSeMBly DiAgRAM
Part
Description
Qty. Part
Description
Qty. Part
Description
Qty.
1
2
3
4
5
6
7
8
9
Foot Cover
1
2
10 Mounting Curve
11 Knob Nut (M8)
12 Socket Head Screw
13 Spacer
1
2
1
1
1
2
2
2
1
19 Hook Clamp
1
2
1
2
1
1
1
Foot
20 Knob Bolt (M8x70)
21 Top Saddle
22 Protector
23 Connector
24 Brake Cap
25 Tray
Tube Cap
Tube Cap
Leg
Head Bar
Clamp Knob
Bolt (M8x70)
Nut (M8)
9
4
2
14 Spring
2
1
15 Front Wheel Stabilizer
16 Knob Bolt
11
10
17 Screw
18 Adjustable Saddle
SKU 98579
For technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
|