Motocross dirt bike stand
66552
set up and operating instructions
®
distributed exclusively by Harbor Freight tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
read this material before using this product.
Failure to do so can result in serious injury.
saVe tHis Manual.
©
®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
c.do not overreach. keep proper
footing and balance at all times.
This enables better control of the tool
in unexpected situations.
11. Keep out of reach of children.
12. Maintain labels and nameplates on
the tool. These carry important safety
information. If unreadable or miss-
ing, contact Harbor Freight Tools for a
replacement.
d.dress properly. do not wear loose
clothing or jewelry. keep your
hair, clothing and gloves away
from moving parts. Loose clothes,
jewelry or long hair can be caught in
moving parts.
13. The warnings, precautions, and in-
structions discussed in this instruction
manual cannot cover all possible con-
ditions and situations that may occur.
It must be understood by the operator
that common sense and caution are
factors which cannot be built into this
product, but must be supplied by the
operator.
e.only use safety equipment that
has been approved by an appropri-
ate standards agency. Unapproved
safety equipment may not provide
adequate protection. Eye protection
must be ANSI-approved and breath-
ing protection must be NIOSH-ap-
proved for the specific hazards in the
work area.
saVe tHese
instructions.
Motocross bike stand
safety Warnings
1. Strap load to Saddle before lifting.
2. Keep clear of Release Bar and do not
leave unattended while supporting
load.
3. Do not exceed 350 lb. capacity.
4. Center load on Saddle.
5. Raise and lower using second person
to stabilize load.
6. Keep out from under load while low-
ering.
7. Inspect before every use; do not use
if parts are loose or damaged.
8. Use as intended only.
9. Operate on flat and level surface.
10. Do not rock load on Stand.
SKU 66552
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
U-Shaped
Bracket
speciFications
Pedal
Weight Capacity
350 lb.
unpacking
Long
Bolt
When unpacking, make sure that the
item is intact and undamaged. If any parts
are missing or broken, please call Harbor
Freight Tools at the number shown on the
cover of this manual as soon as possible.
2. Insert Long Bolt (6) through:
• Washer (9);
• One hole in U-shaped Bracket un-
der Saddle (1);
• Bushing (10);
asseMblY
• Hole in end of Pedal (3);
• Bushing (10);
read the entire iMportant
saFetY inForMation
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
• Other hole in U-shaped Bracket;
• Washer (9).
3. Secure Long Bolt
with a Lock Nut (8).
note: For additional information regarding
the parts listed in the following pages,
refer to the Assembly Diagram near
the end of this manual.
4. Insert Short Bolt (7) through:
• Washer (9);
• Mounting Bracket (5);
• Washer (9);
1. Make sure rubber end caps are se-
cured into feet of Base (2).
• Remaining hole in Pedal (3);
• Washer (9);
• Remaining Mounting Bracket (5);
• Washer (9).
5. Secure Short Bolt with a Lock Nut (8).
Steps 4 and 5
6. Insert remaining Short Bolt (7)
through:
• Washer (9);
Steps 6 and 7
Steps 2 and 3
• Release Bar (4);
• Washer (9);
• Remaining hole in Mounting Brack-
et (5);
• Washer (9);
SKU 66552
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
• Hole in foot on Base (2);
• Washer (9);
locking
pin (11)
• Remaining hole in second Mounting
Bracket (5);
• Washer (9).
7. Secure Short Bolt with Lock Nut (8).
8. Before using the Bike Stand with a
load, test the operation of the Pedal
and Release Bar, without any load,
following the operating instructions
below.
r-pin
(12)
4. Insert Locking Pin (11) fully through
the hole in the saddle and the base
to secure the stand in the up position.
Lock it in place with the R-Pin (12)
operating instructions
read the entire iMportant
saFetY inForMation
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
5.
Warning! stay clear of release
bar while saddle is elevated and in
use.
6. Remove tools from under stand be-
fore lowering.
1. Locate Stand on hard, flat, and level
surface able to withstand load without
deforming.
7. To lower Saddle, keep clear and
remove the R-Pin and Locking Pin.
Place foot on Release Bar and Pedal.
Using second person to stabilize
load, press on Release bar while
guiding Pedal up to smoothly lower
Saddle.
2. Center dirt bike over Saddle and se-
cure to saddle with tie-down strap
(sold separately) before lifting.
3. Using second person to stabilize
load, slowly raise Saddle by de-
pressing Pedal with your foot until
Saddle is fully raised.
SKU 66552
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
please read tHe FolloWing
careFullY
Maintenance and
serVicing
THe MANUFACTUReR AND/OR DISTRIBUTOR
HAS PROvIDeD THe PARTS LIST AND
Procedures not specifically
explained in this manual
must be performed only by a
qualified technician.
ASSeMBLy DIAgRAM IN THIS MANUAL AS
A ReFeReNCe TOOL ONLy. NeITHeR THe
MANUFACTUReR OR DISTRIBUTOR MAKeS
ANy RePReSeNTATION OR WARRANTy OF
ANy KIND TO THe BUyeR THAT He OR SHe
IS qUALIFIeD TO MAKe ANy RePAIRS TO THe
PRODUCT, OR THAT He OR SHe IS qUALIFIeD
TO RePLACe ANy PARTS OF THe PRODUCT.
IN FACT, THe MANUFACTUReR AND/OR
DISTRIBUTOR exPReSSLy STATeS THAT
ALL RePAIRS AND PARTS RePLACeMeNTS
SHOULD Be UNDeRTAKeN By CeRTIFIeD
AND LICeNSeD TeCHNICIANS, AND NOT By
THe BUyeR. THe BUyeR ASSUMeS ALL RISK
AND LIABILITy ARISINg OUT OF HIS OR HeR
RePAIRS TO THe ORIgINAL PRODUCT OR
RePLACeMeNT PARTS THeReTO, OR ARISINg
OUT OF HIS OR HeR INSTALLATION OF
RePLACeMeNT PARTS THeReTO.
to preVent
serious injurY
FroM tool Failure:
do not use damaged
equipment. if abnormal noise
or vibration occurs, have the
problem corrected before
further use.
cleaning and Maintenance
1. beFore eacH use, inspect the
general condition of the tool. Check
for loose screws, misalignment or
binding of moving parts, cracked or
broken parts, and any other condition
that may affect its safe operation.
2. aFter use, clean external surfaces
of the tool with clean cloth.
SKU 66552
For technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
parts list
parts list
part
description
Qty.
part
description
M10x50 Bolt (Short Bolt
M10 Lock Nut
Qty.
1
2
3
4
5
6
Saddle
Base
Pedal
1
1
1
1
2
1
7
8
9
2
3
Washer
11
2
1
Release Bar
Mounting Bracket
M10x70 Bolt (Long Bolt)
10 Bushing
11 Locking Pin
12 R-Pin
1
asseMblY diagraM
9
1
8
10
9
8
9
8
9
5
9
2
3
9
6
9
5
9
9
9
7
9
7
4
note: Locking Pin (11) and R-Pin (12) not shown.
record product’s serial number Here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 66552
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
liMited 90 daY WarrantY
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this prod-
uct is free from defects in materials and workmanship for the period of 90 days from
the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities,
criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental,
contingent, special or consequential damages arising from the use of our product. Some
states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation of exclusion may not apply to you. THIS WARRANTy IS exPReSS-
Ly IN LIeU OF ALL OTHeR WARRANTIeS, exPReSS OR IMPLIeD, INCLUDINg THe
WARRANTIeS OF MeRCHANTABILITy AND FITNeSS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the com-
plaint must accompany the merchandise. If our inspection verifies the defect, we will ei-
ther repair or replace the product at our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you with a replacement. We will return re-
paired products at our expense, but if we determine there is no defect, or that the defect
resulted from causes not within the scope of our warranty, then you must bear the cost
of returning the product.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 66552
For technical questions, please call 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
|