CYCLETREE
Model 02628
ASSEMBLY and OPERATING INSTRUCTIONS
(Bicycle’s not included)
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright © 2002 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools .
For technical questions and replacement parts, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Stay alert. Watch what you are doing, use common sense. Do not assemble the Cycle-
tree when you are tired.
11. Check for damaged parts. Before using this movable bicycle rack, any part that
appears damaged should be carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment and binding of moving parts; any
broken parts or mounting fixtures; and any other condition that may affect proper
operation. Any part that is damaged should be properly repaired or replaced by a
qualified technician.
12. Replacement parts and accessories. When servicing, use only identical replacement
parts. Use of any other parts will void the warranty. Only use accessories intended for use
with this movable bicycle rack. Approved accessories are available from Harbor Freight
Tools.
13. Do not assemble Cycletree if under the influence of alcohol or drugs. Read warning
labels on prescriptions to determine if your judgment or reflexes are impaired while
taking drugs. If there is any doubt, do not assemble the Cycletree .
14. Maintenance. For your safety, parts replacement or repair should be performed by a
qualified technician.
15. Maintain Balance. To obtain the best and safest performance of the Cycletree, be sure
that the multiple hanging bicycles are evenly distributed on the Cycletree. Be careful to
follow the operation instructions on page 4.
Warning:The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be understood
Page 3
SKU 2628
Assembly
Refer to the Assembly Drawing on Page 6.
1. Form a square by facing both of the Base Brackets (#1) toward each other, and inserting
both of the Base Channeled Supports (#2) into the Base Brackets (#1), lining up the holes
on all four corners.
2. Put each of the Casters (#3) through the holes on the four corners of the base frame you
just constructed, from the bottom, so that the square frame sits on them.
3. Place Strut A (#6) on a top of the threaded caster bolt making sure the end with the most
severe angle faces the middle of the square. Refer to the Assembly Drawing on Page 6.
Secure it with a Flat Washer (#4) and Nut (#5).
4. On the opposite corner (diagonal), repeat step three with the other Strut A (#6).
5. On the two remaining corners, repeat the process in step three above, using both of the
Struts B (#8).
6. Set the Base Beam (#7) over the holes on the center of each of the Base Brackets (#1)
and secure it by putting a Bolt (#13) in from the top, and attaching a Flat Washer (#14) and
Nut (#15) from the bottom, on both sides. Make sure that the square receptacle on the Base
Beam (#7) faces up.
7. Slide the Base Post (#9A) through the flexible opening made by the top of the four Struts
and insert it into the square receptacle on the Base Beam (#7).
8. Line up the top of all four Struts with the two connection holes on the Base Post (#9A) and
secure both Struts A (#6) with a Bolt (#13), Flat Washer (#14) and Nut (#15). Next, secure
both Struts B (#8) with a Bolt (#13), Flat Washer (#14) and Nut (#15).
9. Insert the Center Post (#10A) into the Base Post (#9A) and secure it with 2 Bolts (#13A),
2 Flat Washers (#14A) and 2 Nuts (#15A). The Center Post (#10A) has various holes for
height adjustment.
10. Slide the Plastic Covered “T” Bar (#12A) onto the top of the Center Post (#10A) and
secure it with 2 Bolts (#13A), 2 Flat Washers (#14A) and 2 Nuts (#15A).
Operation
Warning: Hanging and dismounting of bicycles should only be done by adults who are
physically capable of safely handling and lifting the weight of a bicycle.
Hanging Bicycles
Hang one bicycle by threading the front wheel spokes through
the plasic covered “T” Bar, the next bicycle must be
hung the same way, but facing the opposite direction, (see photos
to the right and on front cover) continue the same procedure
making sure that all the contigious bicycles hang opposite to
each other. It is recommended that two people assist in hanging
the bicycles to maintain the balance and stability of the Cycletree.
Dismounting Bicycles Before lifting the front wheel off the
Plastic Covered “T” Bar (#12A), place a firm grip on the bicycle
frame, just behind the front fork, making sure that the bicycle
does not sway the wrong way, and carefully remove the bicycle
from the Cycletree.
Maintain balance to obtain the best and safest performance
of the Cycletree. Be sure that the multiple hanging bicycles
are evenly distributed on the Cycletree.
Page 4
REV 12/03; REV 12/06
SKU 2628
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
1. Periodically check that the hardware is tight. Tighten if necessary.
Parts List
Part No.
1
2
Description
Base Bracket
Base Channeled Supports
Castor 3"
Qty.
2
2
3
4
4
5
Flat Washer Ø10
Nut M10
4
4
6
Strut A
2
7
8
Base Beam
Strut B
2
2
9A
10A
12A
13
13A
14
14A
15
15A
Base Post
1
1
1
4
4
4
4
4
Center Post
Plastic Covered T-Bar
Bolt M6
Bolt M8
Flat Washer Ø6
Flat Washer Ø8
Nut M6
Nut M8
4
PLEASE READTHE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM INTHIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBU-
TOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KINDTOTHE BUYERTHAT HE
OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
NOTE: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
Page 5
REV 12/03; 12/06
SKU 2628
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Drawing
Page 6
REV 12/03; 12/06
SKU 2628
Download from Www.Somanuals.com. All Manuals Search And Download.
|