6 / 2 AMP, DUAL RATE
BATTERY CHARGER
45005
E224783
OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND
ALL WARNINGS AND INSTRUCTIONS BEFORE USE.
©
®
Copyright 2005, 2006 by Harbor Freight Tools . All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape or
form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
the grounding prong or modify the plug in any way. Do not use any adapter
plugs. Check with a qualified electrician if you are in doubt as to whether
the outlet is properly grounded. If the equipment should electrically
malfunction or break down, grounding provides a low resistance path to carry
electricity away from the user.
5. Double insulated equipment is equipped with a polarized plug (one blade
is wider than the other). This plug will fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to install a polarized outlet. Do
not change the plug in any way. Double insulation eliminates the need for
the three wire grounded power cord and grounded power supply system.
6. Avoid body contact with grounded surfaces such as pipes, radiators,
ranges, and refrigerators. There is an increased risk of electric shock if your
body is grounded.
7. Do not expose equipment to rain or wet conditions. Water entering
equipment will increase the risk of electric shock.
8. Do not abuse the Power Cord. Never use the Power Cord to carry the
equipment or pull the Plug from an outlet. Keep the Power Cord away
from heat, oil, sharp edges, or moving parts. Replace damaged Power
Cords immediately. Damaged Power Cords increase the risk of electric shock.
9. When operating equipment outside, use an outdoor extension cord
marked “W-A”or “W”. These extension cords are rated for outdoor use, and
reduce the risk of electric shock.
PERSONAL SAFETY
10. Stay alert. Watch what you are doing, and use common sense when
operating equipment. Do not use equipment while tired or under the
influence of drugs, alcohol, or medication. A moment of inattention while
operating equipment may result in serious personal injury.
11. Avoid accidental starting. Be sure the Power Switch is off before plugging
in. Plugging in equipment with the Power Switch on, invites accidents.
12. Use safety equipment. Always wear eye protection. Dust mask, nonskid
safety shoes, hard hat, or hearing protection must be used for appropriate
conditions. Always wear ANSI approved safety goggles and a dust mask/
respriator when using or performing maintenance on this equipment.
EQUIPMENT USE AND CARE
13. Do not force the equipment. Use the correct equipment for your
application. The correct equipment will do the job better and safer at the rate
SKU 45005
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
for which it is designed. Do not use the equipment for a purpose for which it is
not intended.
14. Do not use the equipment if the Power Switch does not turn it on or off.
Any equipment that cannot be controlled with the Power Switch is dangerous
and must be replaced.
15. Disconnect the Power Cord Plug from the power source before making
any adjustments, changing accessories, or storing the equipment. Such
preventive safety measures reduce the risk of starting the equipment
accidentally. Always unplug the equipment from its electrical outlet before
performing any inspection, maintenance, or cleaning procedures.
16. Store idle equipment out of reach of children and other untrained persons.
Equipment is dangerous in the hands of untrained users.
17. Maintain equipment with care. Do not use damaged equipment. Tag
damaged equipment “Do not use” until repaired.
18. Check for breakage of parts and any other condition that may affect the
equipment’s operation. If damaged, have the equipment serviced before
using. Many accidents are caused by poorly maintained equipment.
19. Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one piece of equipment may
become hazardous when used on another piece of equipment.
SERVICE
20. Equipment service must be performed only by qualified repair personnel.
Service or maintenance performed by unqualified personnel could result in a
risk of injury.
21. When servicing equipment, use only identical replacement parts. Follow
instructions in the “Inspection, Maintenance, And Cleaning” section of
this manual. Use of unauthorized parts or failure to follow maintenance
instructions may create a risk of electric shock or injury.
Additional Battery Charger Safety Precautions
1. This Battery Charger must only be used on lead-acid, rechargeable type
batteries. Do not use this Battery Charger to charge household, dry-cell
batteries. Dry-cell batteries may explode causing personal injury or property
damage.
2. Do not use the Battery Charger as a low voltage system power supply except
in automotive applications.
3. Do not try to start the automobile engine when the Battery Charger is connected
to the battery. It may damage the unit.
SKU 45005
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Always charge a lead-acid battery in a well ventilated area as explosive gases
may be produced during charging.
5. Place the Battery Charger as far away from the battery as possible during
charging.
6. Do not attempt to charge a battery with frozen battery fluid.
7. Be careful not to drip any battery fluids in or around the Battery Charger.Damage
to the charger can occur.
8. Never touch the Battery Charger cable clamps together when the charger is
plugged in; touching the cable clamps together may cause personal injury.
9. Avoid touching your eyes after working with a lead-acid battery. Wash hands
thoroughly with soap and water. If battery fluids contact the skin, face, or eyes,
immediately flush with plenty of fresh water. Then, contact a doctor.
10. Never smoke around a charging battery.
11. Make all Cable Clamp connections before plugging in the Battery Charger.
12. Remove all metal objects (including tools and other personal objects, i.e., watch)
from around the battery being charged.
13. Make sure battery is vented and that it’s a maintenance free (non-fillable) battery.
Make sure vents are clear and dirt free.
14. Use this product in accordance with the battery’s and vehicle’s instruction
manual recommendations, safety warnings and charging instructions.
15. Never leave Battery Charger unattended.
16. Batteries can explode under certain conditions; excessive heat and/or poor
ventilation can cause explosive gas buildup and battery explosion.
Surges in electrical power supply could possibly cause battery explosion.Battery
Charger should be plugged into a surge protection device.
SKU 45005
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
GROUNDING
WARNING!
Improperly connecting the grounding wire can result in the risk of
electric shock. Check with a qualified electrician if you are in doubt as
to whether the outlet is properly grounded. Do not modify the power
cord plug provided with the tool. Never remove the grounding prong
from the plug. Do not use the tool if the power cord or plug is dam-
aged. If damaged, have it repaired by a service facility before use. If
the plug will not fit the outlet, have a proper outlet installed by a quali-
fied electrician.
GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS
1. Tools marked with “Grounding Required” have a three wire cord and three
prong grounding plug. The plug must be connected to a properly grounded
outlet. If the tool should electrically malfunction or break down, grounding
provides a low resistance path to carry electricity away from the user, reducing
the risk of electric shock. (See Figure A.)
2. The grounding prong in the plug is connected through the green wire inside
the cord to the grounding system in the tool. The green wire in the cord must
be the only wire connected to the tool’s grounding system and must never be
attached to an electrically “live” terminal. (See Figure A.)
3. Your tool must be plugged into an appropriate outlet, properly installed and
grounded in accordance with all codes and ordinances. The plug and outlet
should look like those in the following illustration. (See Figure A.)
FIGURE A
FIGURE B
DOUBLE INSULATEDTOOLS:TOOLSWITHTWO PRONG PLUGS
4. Tools marked “Double Insulated” do not require grounding. They have a special
double insulation system which satisfies OSHA requirements and complies
with the applicable standards of Underwriters Laboratories, Inc., the Canadian
Standard Association, and the National Electrical Code. (See Figure B.)
SKU 45005
For technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Double insulated tools may be used in either of the 120 volt outlets shown in
the following illustration. (See Figure B.)
EXTENSION CORDS
1. Grounded tools require a three wire extension cord. Double Insulated tools
can use either a two or three wire extension cord.
2. As the distance from the supply outlet increases, you must use a heavier gauge
extension cord. Using extension cords with inadequately sized wire causes a
serious drop in voltage, resulting in loss of power and possible tool damage.
(See Figure C.)
3. The smaller the gauge number of the wire, the greater the capacity of the cord.
For example, a 14 gauge cord can carry a higher current than a 16 gauge cord.
(See Figure C.)
4. When using more than one extension cord to make up the total length, make
sure each cord contains at least the minimum wire size required.
(See Figure C.)
5. If you are using one extension cord for more than one tool, add the nameplate
amperes and use the sum to determine the required minimum cord size.
(See Figure C.)
6. If you are using an extension cord outdoors, make sure it is marked with the
suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.
7. Make sure your extension cord is properly wired and in good electrical condition.
Always replace a damaged extension cord or have it repaired by a qualified
electrician before using it.
8. Protect your extension cords from sharp objects, excessive heat, and damp or
wet areas.
RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS*
NAMEPLATE
AMPERES
(At Full Load)
EXTENSION CORD LENGTH
25 Feet
18
50 Feet
75 Feet
100 Feet
150 Feet
0 - 2.0
2.1 - 3.4
18
18
18
16
14
12
10
18
18
16
14
12
10
-
18
16
14
12
10
-
16
14
12
12
-
18
3.5 - 5.0
18
5.1 - 7.0
18
7.1 - 12.0
12.1 - 16.0
16.1 - 20.0
18
14
-
12
-
-
* Based on limiting the line voltage drop to five
volts at 150% of the rated amperes.
FIGURE C
SKU 45005
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLOGY
Unpacking
When unpacking, make sure that the Battery Charger is intact and undamaged.
If any parts are missing or broken, please call Harbor Freight Tools at the number
on the cover of this manual.
Operation
1. Place the Battery Charger about six feet from the battery being charged.
2. If the battery to be charged is in a vehicle, verify that the ignition is off, remove
vehicle’s cables from battery, then connect the positive (Red with +) Cable
Clamp to the positive (+ or P) terminal of the battery.
If necessary, clean the battery terminals.Wiggle the Cable Clamp on the battery
terminal to get a good connection.
3. Connect the negative (Black with –) to an unpainted, solid metal portion of the
vehicle.
If the battery is outside the vehicle, connect the negative (black with –) Cable
Clamp to the negative battery terminal.
4. Set the Battery Charger switch to the proper setting for the type battery being
charged. Refer to the table on the next page.
SKU 45005
For technical questions, please call 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery
Voltage / Amps
Switch Setting
Charging Time
Typical Battery Uses
Right
(12 volt, 6 amp)
Vehicles, machinery with
large engines
12 volt, 6 amps
12 volt, 2 amps
6 to 8 hours
Motorcycles, snowmobiles,
small engines; Drip charge
battery; For batteries rated
at 28 amphours or less.
Center
(12 volt, 2 amp)
3 to 8 hours
6 to 8 hours
Vehicles, machinery with
large engines using 6 volt
battery
Left
(6 volt, 6 amp)
6 volt, 6 amps
Mode Switch
5. With the Battery Clamps in place, and the Mode Switch correctly set, plug the
3-prong line cord into a grounded electrical outlet or extension cord.
6. The Battery Charger is now supplying charging current to the battery. View the
Ammeter to see the amount of charging current.
% Charge Scale
Fully Charged
Charging at full 2 amps
Charging at full 6 amps
The ammeter displays the amount of current draw of the battery. As the battery
charges, it draws less current.The ammeter indicator moves down as the battery
charges.When its reaches the green area of the ammeter, the battery is charged.
When the charge setting is 12 volts, 6 amps, the percentage (%) charge scale
can be read as an indication of the charge.
SKU 45005
For technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
7. When the battery is fully charged, the Battery charger will automatically shut
off.Note:When set in 6 volt mode,the Battery Charger will not automatically
shut off; it must be manually turned off.
8. Remove the negative (black) Cable Clamp from the battery.
9. Remove the positive (red) Cable Clamp from the battery.
Maintenance
1. Using a clean cloth, wipe the Cable Clamps and charger of all grease and dirt.
2. Coil all cables.
3. Store the Battery Charger in a clean and dry location.
4. If any cable insulation becomes cracked and exposes copper wire, have it
repaired or replaced by a qualified technician.
Troubleshooting
Symptom
Maximum
ammeter reading
Probable Causes
Remedy
Defective battery
Check and/or replace battery
Check power cable and outlet
connections
No power to charger
No ammeter
reading
Battery cable clamps not
connected to battery properly
Clean battery terminals and reset
cable clamps
Defective battery
Check and/or replace battery
Continue charging
Battery is partially charged
Charging current
not to full output Defective battery, will not hold Check and/or replace battery
full charge
Battery is completely dead
Continue charging battery. Charger
will continue to reset itself until the
battery charge reaches a chargable
level.
Ammeter needle
moves up to full
charge, then
drops to zero.
Makes clicking
noise.
Defective battery
Check and/or replace battery
Charger is resetting itself
Wait until charger automatically
after circuit breaker overload resets itself.
Note: No replacement parts are available for the Battery Charger.
SKU 45005
For technical questions, please call 1-800-444-3353.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
|