ADIRONDACK ROCKER
91092
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright © 2004 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Stay alert. Watch what you are doing, use common sense during assembly,
and use of this chair.
8. Use eye and ear protection. Always wear ANSI approved impact safety
goggles during assembly.
9. Take caution as some woods contain preservatives such as copper
chromium arsenate (CCA) which can be toxic. When handling these
materials extra care should be taken to avoid inhalation and minimize skin
contact.
10. Check for damaged parts. Before using this chair, any part that appears
damaged should be carefully checked to determine that it will operate properly
and perform its intended function. Any part that is damaged should be properly
repaired or replaced.
11. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty.
12. Do not assemble this chair if under the influence of alcohol or drugs.
Read warning labels on prescriptions to determine if your judgment or reflexes
are impaired while taking drugs. If there is any doubt, do not proceed with
assembly.
13. Maintenance. For your safety, service and maintenance should be performed
regularly. Check the alignment of all parts, and check the tightness of all
fasteners.
Warning: The warnings, cautions, and instructions discussed in this
instruction manual cannot cover all possible conditions and situations
that may occur. It must be understood by the operator that common
sense and caution are factors which cannot be built into this product,
but must be supplied by the operator.
Unpacking
When unpacking, check to make sure the following parts are included.
1 Back
1 Back Brace
1 Seat
10 Wood Screws
2 Front Legs
2 Back Supports
2 Arms
10 55mm Bolts with nut and washer
2 65mm Bolts with nut and washer
1 Owner’s Manual
2 Rockers
2 50mm Bolt with Nut and washer
4 80mm Bolt with nut and washer
If any parts are missing or broken, please call Harbor Freight Tools at the number
on the cover of this manual, or contact your local Harbor Freight retailer.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 3
SKU 91092
Assembly Drawing
D
D
C1
B
F
L
Step 2
Step 1
I
Attach F (right and left) with C1 and C2.
using 4 bolts, washers and nuts (I). Attach
D (right and left) to B (seat, back end) and
F using 4 bolts, washers and nuts (L).
Attach the front end of B to C1 & C2
with 6 bolts, washers and nuts (I).
F
G
A
Step 3
Step 4
Connecting G with the back of A, using
2 bolts, washers & nuts (K).
Attach A with D & G, using 4 screws (H).
Attach A with B, using 2 screws (H).
C2
C1
Step 5
Attach E1 and E2 to D, using 2 bolts,
washers and nuts (J). Attach E1 to C1
with screws (H). Repeat with E2 to C2
with (H).
Completed. Make sure all screws, nuts and
bolts are tightened and in place. Before using,
test the Rocker by rocking it back and forth
and being sure it is safe to operate.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 4
SKU 91092
Maintenance
1. This chair is made of natural Fir wood. This beautiful material will naturally
weather over time, especially if used outdoors.You can manage the speed
and extent of this weathering by controlling the environment in which the chair
is used and stored, as well as any coatings you may apply.
2. Leaving the chair outside exposed to weather, especially direct sun, rain and
salt air, will speed the weathering process.This can be slowed by removing
the chair from these conditions, or covering it with a suitable cover.
3. You may wish to stain, varnish or paint the chair. If so, follow the instructions
supplied with these coatings.
4. Occasionally wash the chair with a garden hose or pressure sprayer to
remove accumulated dust or dirt. Wipe down or blow off any remaining water
left on the chair after washing.
5. Periodically (perhaps once per year), recheck the tightness of all fasteners.
Normal usage of the chair and weathering of the wood may cause fasteners
to loosen. If fasteners can not be tightened, use wood glue or some other
appropriate bonding material to ensure that fasteners remain tight.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 5
SKU 91092
Parts List
Back
Seat
Left Front Leg
Right Front Leg
Back Support
Left Arm
Right Arm
Rocker
Back Brace
Screw
55mm Bolt
65mm Bolt
with Washer and Nut
with Washer and Nut
50mm Bolt
80mm Bolt
with Washer and Nut
with Washer and Nut
NOTE: Some parts are listed and shown for illustration purposes only and are not
available individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER
NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO
THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE
PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE
PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THat ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS
OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 6
SKU 91092
|