Harbor Freight Tools Automobile Parts 66183 User Manual

60” farm jack  
66183  
Set up and Operating inStructiOnS  
®
distributed exclusively by Harbor freight tools .  
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Visit our website at: http://www.harborfreight.com  
read this material before using this product.  
failure to do so can result in serious injury.  
SaVe tHiS manual.  
©
®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this manual or any  
artwork contained herein may be reproduced in any shape or form without the express written  
consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally.  
Due to continuing improvements, actual product may differ slightly from the product described  
herein. Tools required for assembly and service may not be included.  
for technical questions or replacement parts, please call 1-800-444-3353.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
c. dress properly. do not wear  
loose clothing or jewelry. keep  
your hair, clothing and gloves  
away from moving parts. Loose  
clothes, jewelry or long hair can be  
caught in moving parts.  
farm jack Safety Warnings  
1. Be aware of dynamic loading! Sud-  
den load movement may briefly create  
excess load causing product failure.  
2. Use the Jack on solid, level surfaces,  
capable of supporting the weight of  
the Jack, equipment being lifted, and  
operator.  
d. Only use safety equipment that  
has been approved by an appro-  
priate standards agency. Unap-  
proved safety equipment may not  
provide adequate protection. Eye  
protection must be ANSI-approved  
and breathing protection must be  
NIOSH-approved for the specific  
hazards in the work area.  
3. Do not exceed the lifting capacity  
(7,000 pounds) of the Jack.  
4. Maintain labels and nameplates on  
the tool. These carry important safety  
information. If unreadable or miss-  
ing, contact Harbor Freight Tools for a  
replacement.  
3. tool use and care  
a. do not force the tool. use the  
correct tool for your application.  
The correct tool will do the job bet-  
ter and safer at the rating for which  
it was designed.  
5. This product is not a toy. Keep it out  
of reach of children.  
6. The warnings, precautions, and  
instructions discussed in this instruc-  
tion manual cannot cover all possible  
conditions and situations that may  
occur. It must be understood by the  
operator that common sense and cau-  
tion are factors which cannot be built  
into this product, but must be supplied  
by the operator.  
b. Store idle tools out of the reach  
of children and do not allow per-  
sons unfamiliar with it or these  
instructions to operate the tool.  
Tools are dangerous in the hands of  
untrained users.  
c. maintain your tools. check for  
misalignment or binding of mov-  
ing parts, breakage of parts and  
any other condition that may  
affect the tool’s operation. if  
damaged, have the tool repaired  
before use. Many accidents are  
caused by poorly maintained tools.  
d. use the tool in accordance with  
these instructions, taking into  
account the working conditions  
and the work to be performed.  
Use of the tool for operations differ-  
ent from those intended could result  
in a hazardous situation.  
SKU 66183  
for technical questions, please call 1-800-444-3353.  
Page 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
masonry expansion anchors (not in-  
cluded). Only use materials capable  
of bearing the weight of the Jack and  
load being lifted.  
SpecificatiOnS  
Jack Capacity  
7,000 Pounds  
59-1/4”  
6”  
Maximum Lift  
Minimum Height  
4. To raise loads, pull the Ratchet Con-  
trol Lever (10) up until the mechanism  
clicks and the Latch engages.  
unpacking  
5. Place the jack’s lift nose completely  
under the object being lifted.  
When unpacking, make sure that  
the item is intact and undamaged. If any  
parts are missing or broken, please call  
Harbor Freight Tools at the number shown  
on the cover of this manual as soon as  
possible.  
6. Slowly pump the handle to raise the  
load. Keep a firm grip on the handle  
while operating the jack.  
7.  
caution! To avoid injury keep  
hands away from the Lift Nose when  
raising a load. Keep bystanders and  
pets away when a load is raised. Do  
not work under a raised load.  
note: For additional information regarding  
the parts listed in the following pages,  
refer to the Assembly Diagram near  
the end of this manual.  
8. After the load is raised to the desired  
height, insert a grade 5, 1/2 inch bolt  
(sold separately) through the hole in  
the Lift Column (2) immediately below  
the lifting mechanism.  
Operating inStructiOnS  
read the entire impOrtant  
SafetY infOrmatiOn  
section at the beginning of this  
manual including all text under  
subheadings therein before set  
up or use of this product.  
ratchet control  
lever (10) in down  
position.  
ratchet  
1. Designate a work area that is clean  
and well-lit. The work area must not  
allow access by children or pets to  
prevent injury and distraction.  
latch (11)  
lift  
nose  
2. Use the Jack on solid, level surfaces,  
capable of supporting the weight of  
the Jack, equipment being lifted, and  
operator.  
Handle  
3. To increase stability, the Jack can be  
bolted to a thick board, metal plate,  
or a cement surface. Use the three  
mounting holes on the Base as a tem-  
plate to mark the location where three  
1/2” diameter holes will be drilled into  
the surface. Drill and clean out the  
three holes. Align the three mount-  
ing holes with the three drilled holes  
and secure the Jack to the floor using  
9. Insert additional supports to make  
sure the load is properly supported at  
the lift point to prevent shifting.  
10. To lower the load; move the Ratchet  
Control Lever to the down position,  
SKU 66183  
for technical questions, please call 1-800-444-3353.  
Page 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
and pump the Handle up and down  
slowly. The latch will click as the  
load is lowered. Continue pumping  
OR DISTRIBUTOR MAKeS ANy ReP-  
ReSeNTATION OR WARRANTy OF ANy  
KIND TO THe BUyeR THAT He OR SHe  
the Handle until the load rests on the IS qUALIFIeD TO MAKe ANy RePAIRS  
ground.  
TO THe PRODUCT, OR THAT He OR  
SHe IS qUALIFIeD TO RePLACe ANy  
PARTS OF THe PRODUCT. IN FACT,  
THe MANUFACTUReR AND/OR DIS-  
TRIBUTOR exPReSSLy STATeS THAT  
ALL RePAIRS AND PARTS RePLACe-  
MeNTS SHOULD Be UNDeRTAKeN By  
CeRTIFIeD AND LICeNSeD TeCHNI-  
CIANS, AND NOT By THe BUyeR. THe  
BUyeR ASSUMeS ALL RISK AND LI-  
ABILITy ARISINg OUT OF HIS OR HeR  
RePAIRS TO THe ORIgINAL PRODUCT  
OR RePLACeMeNT PARTS THeReTO,  
OR ARISINg OUT OF HIS OR HeR IN-  
STALLATION OF RePLACeMeNT PARTS  
THeReTO.  
11. Clean, then store the tool indoors out  
of children’s reach.  
uSer-maintenance  
inStructiOnS  
Procedures not specifically  
explained in this manual must  
be performed only by a qualified  
technician.  
tO preVent  
SeriOuS injurY  
frOm tOOl failure:  
do not use damaged  
equipment. if abnormal noise  
occurs, have the problem  
corrected before further use.  
cleaning, maintenance, and  
lubrication  
1. BefOre eacH uSe, inspect the  
general condition of the tool. Check  
for loose screws, misalignment or  
binding of moving parts, cracked or  
broken parts and any other condition  
that may affect its safe operation.  
2. periOdicallY, lubricate moving  
parts of the Jack with lubricating oil.  
3. after uSe, clean the tool with clean  
cloth.  
pleaSe read tHe  
fOllOWing carefullY  
THe MANUFACTUReR AND/OR DIS-  
TRIBUTOR HAS PROvIDeD THe PARTS  
LIST AND ASSeMBLy DIAgRAM IN  
THIS MANUAL AS A ReFeReNCe TOOL  
ONLy. NeITHeR THe MANUFACTUReR  
SKU 66183  
for technical questions, please call 1-800-444-3353.  
Page 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
partS liSt  
partS liSt  
part  
1
2
3
4
description  
Qty  
1
1
1
1
part  
description  
Qty  
1
1
1
1
Runner  
14 Spring Washer  
15 Base  
16 Bolt  
17 Bolt  
18 Spring  
19 Pin  
Lift Column  
Connecting Rod  
Rocker with Handle  
Washer  
5
6
1
1
1
2
Nut  
7
8
9
Pin  
Screw  
Washer  
1
1
1
1
1
1
1
20 Reverse Rod  
21 Spring  
22 Spring  
23 Washer  
24 Nut  
2
1
1
1
1
1
1
10 Ratchet Control Lever  
11 Ratchet Latch  
12 Bolt  
25 Runner  
26 Washer  
13 Nut  
record product’s Serial number Here:  
note: If product has no serial number, record month and year of purchase instead.  
note: Some parts are listed and shown for illustration purposes only, and are not available indi-  
vidually as replacement parts.  
SKU 66183  
for technical questions, please call 1-800-444-3353.  
Page 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
diagram  
7
SKU 66183  
for technical questions, please call 1-800-444-3353.  
Page 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
limited 90 daY WarrantY  
Harbor Freight Tools Co. makes every effort to assure that its products meet  
high quality and durability standards, and warrants to the original purchaser that this  
product is free from defects in materials and workmanship for the period of 90 days  
from the date of purchase. This warranty does not apply to damage due directly or  
indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside  
our facilities, criminal activity, improper installation, normal wear and tear, or to lack of  
maintenance. We shall in no event be liable for death, injuries to persons or property,  
or for incidental, contingent, special or consequential damages arising from the use of  
our product. Some states do not allow the exclusion or limitation of incidental or con-  
sequential damages, so the above limitation of exclusion may not apply to you. THIS  
WARRANTy IS exPReSSLy IN LIeU OF ALL OTHeR WARRANTIeS, exPReSS OR  
IMPLIeD, INCLUDINg THe WARRANTIeS OF MeRCHANTABILITy AND FITNeSS.  
To take advantage of this warranty, the product or part must be returned to us  
with transportation charges prepaid. Proof of purchase date and an explanation of the  
complaint must accompany the merchandise. If our inspection verifies the defect, we  
will either repair or replace the product at our election or we may elect to refund the  
purchase price if we cannot readily and quickly provide you with a replacement. We will  
return repaired products at our expense, but if we determine there is no defect, or that  
the defect resulted from causes not within the scope of our warranty, then you must  
bear the cost of returning the product.  
This warranty gives you specific legal rights and you may also have other rights  
which vary from state to state.  
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353  
SKU 66183  
for technical questions, please call 1-800-444-3353.  
Page 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Grizzly Grinder G5968 9 User Manual
Haier Oven RTC1700SS User Manual
Harbor Freight Tools Patio Furniture 3551 User Manual
Honeywell Humidifier HM506 User Manual
Honeywell Thermostat WEB 201 User Manual
Hotpoint Clothes Dryer AQC9 BF7 User Manual
Hotpoint Range RGB744GEJ User Manual
Humax Flat Panel Television LGB 19DZT User Manual
Husqvarna Snow Blower 1130SBE OV User Manual
iHome Portable Speaker IDM12 User Manual