AIR FILTER, REGULATOR AND
LUBRICATOR
92261/
45009
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
®
Copyright © 2004 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
Do not overreach. Keep proper footing and balance at all times. Do not reach over or
across running machines.
7. Dress properly. Do not wear loose clothing or jewelry as they can be caught
in moving parts. Protective, electrically nonconductive clothes and nonskid
footwear are recommended when working. Wear restrictive hair covering to
contain long hair.
8.
Use eye and ear protection. Always wear ANSI-approved impact safety goggles when
using air tools. Wear a full face shield if you are producing metal filings or wood chips.
Wear a NIOSH-approved dust mask or respirator when working around metal, wood,
and chemical dusts and mists.
9.
Maintain tools with care. Keep tools sharp and clean for better and safer performance.
Follow instructions for lubricating and changing accessories. Inspect tool cords
periodically and, if damaged, have them repaired by an authorized technician. The
handles must be kept clean, dry, and free from oil and grease at all times.
10. Disconnect power. Unplug air compressor (not included) when not in use.
11. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches are
removed from the tool or machine work surface before plugging it in.
12. Avoid unintentional starting. Do not carry any air tool with your finger on the trigger,
whether it is plugged in or not.
13. Stay alert. Watch what you are doing, use common sense. Do not operate any tool
when you are tired.
14. Check for damaged parts. Before using any tool, any part that appears damaged
should be carefully checked to determine that it will operate properly and perform its
intended function. Check for alignment and binding of moving parts; any broken parts
or mounting fixtures; and any other condition that may affect proper operation. Any part
that is damaged should be properly repaired or replaced by a qualified technician. Do
not use any air tool if its switch does not turn On and Off properly.
15. Replacement parts and accessories. When servicing, use only identical replacement
parts. Use of any other parts will void the warranty.
16. Do not operate air tools if under the influence of alcohol or drugs. Read warning
labels if taking prescription medicine to determine if your judgment or reflexes are
impaired while taking drugs. If there is any doubt, do not operate the tool.
17. Maintenance. For your safety, service and maintenance should be performed regularly
by a qualified technician.
18. Before using any air tool, read and adhere to all instructions and safety warnings provided
in the instruction manual of the tool being used.
19. Warning: The brass components of this product contain lead, a chemical known
to the State of California to cause birth defects (or other reproductive harm).
(California Health & Safety Code § 25249.5, et seq.)
Warning:The warnings,cautions,and instructions discussed in this instruction
SKU 45009, 92261 For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 3
manual cannot cover all possible conditions and situations that may occur.
It must be understood by the operator that common sense and caution are
factors which cannot be built into this product, but must be supplied by the
operator.
Unpacking
When unpacking, check to make sure all parts are included. Refer to the photo
below, and the Parts List and Diagram located at the end of this manual. If any
parts are missing or broken, please call Harbor Freight Tools at the number on the
cover of this manual.
Regulator
Pressure Gauge (12B)
Bowl (2B)
Air Filter Body (1A)
Lubricator Body (6C)
Air Outlet
(to Air Tool)
Air Inlet (from
Compressor)
Mounting Bracket
(11B)
Lubricator Metal
Guard (12C)
Air Filter Metal
Guard (9A)
Air Pressure
Adjusting Rod (1B)
Quick Release Button
Quick Release Button
Assembly
1. Secure the Mounting Bracket (11B) to the Regulator Bowl (2B) if the unit is to
be mounted to a flat surface. See photo above.
Use the screws holding the Regulator Bowl to the Regulator Valve (6B).
Securely tighten. The Mounting Bracket holes must face to the rear of the
unit.
2. Apply pipe thread seal tape to the fitting of the Pressure Gauge (12B).
3. Carefully screw in (clockwise) the Pressure Gauge fitting into the Regulator
Valve (6B).
Do not overtighten. Stop turning the Pressure Gauge when the scale is
facing up as shown above.
REV 07/06
SKU 45009, 92261 For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 4
4. Verify that the air Filter Element (4A) is in place on the Filter Body (1A), then
place the Plastic Bowl (7A), labeled Air Filter, inside the Metal Guard (9A).
5. Slide the Upper Lid (10A) over the Metal Guard (9A) and place into the Filter
Body (1A). Securely tighten the Upper Lid (10A) by turning clockwise.
6. Place the oiler Plastic Bowl (10C), with O-ring (9C), into the Metal Guard
(12C).
7. Slide the Upper Lid (13C) over the Metal Guard (12C) and place into the
Lubricator Body (6C). Securely tighten the Upper Lid (13C) by turning
clockwise.
8. Secure the unit assembly by the Mounting Bracket (11B) to a flat surface
using the appropriate hardware (not supplied).
9. Remove the Oil Plug (2C) on top of the Lubricator Body (6C) and add air
lubricator oil to the maximum level. Replace Oil Plug.
Air Connections
Caution: Avoid injuries. Before connecting this unit to the air compressor, be
certain that the air compressor is unplugged from the power source, and all
pressure is released from its tank.
The illustration below shows the general connection for the Air Filter-Regulator
and Lubricator.
1. Apply pipe thread seal tape to the both ends of a double-sided connector
(not supplied), and screw into the air inlet of the Filter Body (1A). Securely
tighten.
2. Apply pipe thread seal tape to the both ends of a double-sided connector
(not supplied), and screw into the air outlet of the Lubricator Body (6C).
Securely tighten.
3. Connect the compressor air output hose or pipe to the air inlet connector
(not supplied) on the Filter Body (1A). Quick connectors and couplings (not
supplied) may be used for convenience. Use pipe thread seal tape.
SKU 45009, 92261 For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 5
4. Connect the air output hose to the air outlet connector (not supplied) on the
Lubricator Body (6C). Quick connectors and couplings (not supplied) may be
used for convenience. Use pipe thread seal tape.
Operation
1. Turn on the Compressor and check for air leaks.
If any are found, turn the Compressor off, drain air from tank, and fix the
leak.
2. With the Compressor ON, turn the Air Pressure Adjusting Rod (1B) to adjust
the air pressure as read on the Pressure Gauge (12B).
3. Adjust the oil flow by viewing the View Dome (1C) and adjusting the Oil Feed
Adjustment Screw (4C) next to it.
4. Under pressure, press the Quick Release Button to expel any accumulated
moisture from the Air Filter. Do this daily.
Maintenance
1. Check oil level in Lubricator Plastic Bowl (10C) daily. Refill if below minimum
level.
2. Periodically disassemble the Air Filter and Lubricator assemblies and remove
all dirt and debris. Remove air pressure before cleaning.
Parts List
Part
1A
2A
3A
4A
5A
6A
7A
8A
9A
Description
Part
Description
Filter Body
O-ring
10B Pop-up Valve Cap
11B Mounting Bracket
12B Pressure Gauge
Spiral Baffle
Filter Element
Umbrella Baffle
Screw Rod
Plastic Bowl
Plastic Drain
Metal Guard
1C
2C
3C
4C
5C
6C
7C
8C
9C
View Dome
Oil Plug
O-ring
Oil Feed Adjustment Screw
Drip Tube
Lubricator Body
Screw Rod
Coupler
10A Upper Lid
1B
2B
3B
4B
5B
6B
7B
8B
9B
Adjusting Rod
Regulator Bowl
Spring Washer
Spring
O-ring
10C Plastic Bowl
11C Plastic Drain
12C Metal Guard
13C Upper Lid
1D
2D
Diaphragm
Regulator Valve
Regulator Valve
Spring
Filter-Regulator Connector
Lubricator-Regulator Connector
O-ring
NOTE: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
SKU 45009, 92261 For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 6
Assembly Drawing
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS
MANUAL AS A REFERENCETOOL ONLY. NEITHERTHE MANUFACTURER NOR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR
SHE IS QUALIFIEDTO MAKE ANY REPAIRSTOTHE PRODUCT ORTHAT HE OR SHE IS QUALI-
FIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER.
THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO
THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS
OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 45009, 92261 For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 7
|