Harbor Freight Tools Automobile Accessories 92626 User Manual

2000 LB. CAPACITY  
A-FRAME TRAILER JACK  
92626  
SET UP AND OPERATING INSTRUCTIONS  
Read this material before using this product.  
Failure to do so can result in serious injury.  
SAVE THIS MANUAL.  
©
®
Copyright 2010 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork  
contained herein may be reproduced in any shape or form without the express written consent of  
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing  
improvements, actual product may differ slightly from the product described herein. Tools required for  
assembly and service may not be included.  
For technical questions or replacement parts, please call 1-800-444-3353.  
Rev 11a  
Download from Www.Somanuals.com. All Manuals Search And Download.  
This enables better control of the  
tool in unexpected situations.  
will ensure that the safety of the tool  
is maintained.  
d. Dress properly. Do not wear  
loose clothing or jewelry. Keep  
your hair, clothing and gloves  
away from moving parts. Loose  
clothes, jewelry or long hair can be  
caught in moving parts.  
Specific Safety Warnings  
1. Do not exceed 2000 Lb. capacity.  
2. Use on flat, level, hard surface  
capable of supporting load.  
3. Tool use and care  
3. Wear ANSI-approved safety goggles  
during use.  
a. Do not force the tool. Do not  
attempt to lift more than the 2,000  
lb. maximum lifting capacity of  
this tool. The correct tool will do  
the job better and safer at the rate  
for which it was designed.  
4. Prevent trailer wheels from moving by  
using wheel chocks while raising or  
lowering.  
5. Before towing, fully raise trailer jack  
and secure properly.  
b. Store idle tools out of reach of  
children and do not allow persons  
unfamiliar with the tool or these  
instructions to operate it. Tools are  
dangerous in the hands of untrained  
users.  
6. Keep out from under jack and tongue  
when applying and releasing load,  
when jack is supporting load, or when  
moving trailer.  
7. Inspect before use. Do not use if  
parts are loose or damaged.  
c. Maintain tools. Check for  
misalignment or binding of  
moving parts, breakage of parts  
and any other condition that may  
affect the tool’s operation. If  
damaged, have the tool repaired  
before use. Many accidents are  
caused by poorly maintained tools.  
8. Use in accordance with the  
Department of Transportation (DOT)  
regulations. Information about DOT  
gov/regulations.html  
9. Read manual before installation and/  
or use.  
d. Use the tool and accessories  
in accordance with these  
instructions, taking into account  
the working conditions and the  
work to be performed. Use of the  
tool for operations different from  
those intended could result in a  
hazardous situation.  
10. Maintain labels and nameplates on  
the tool. These carry important safety  
information. If unreadable or missing,  
contact Harbor Freight Tools for a  
replacement.  
11. This product is not a toy. Keep it out  
of reach of children.  
4. Service  
a. Have your tool serviced by a  
qualified repair person using only  
identical replacement parts. This  
12. Not for aircraft purposes.  
13. Trailer Jack must always be retracted  
when towing the trailer.  
SKU 92626  
For technical questions, please call 1-800-444-3353.  
Page 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14. The warnings, precautions,  
and instructions discussed in  
this instruction manual cannot  
cover all possible conditions and  
situations that may occur. It must  
be understood by the operator that  
common sense and caution are  
factors which cannot be built into this  
product, but must be supplied by the  
operator.  
SpecificSatPioEnsCIFICATIONS  
Weight Capacity 2000 lb.  
Jack Lift  
Installation  
Handle  
15”  
Bolt on or Weld on Mounting  
Rotates 360 degrees  
24-1/4”  
Height  
UNPACKING  
SAVE THESE  
INSTRUCTIONS.  
When unpacking, make sure item  
is intact and undamaged. If parts are  
missing or broken, call Harbor Freight  
Tools at 1-800-444-3353.  
Installation / Assembly  
SET UP INSTRUCTIONS  
Read the ENTIRE IMPORTANT  
SAFETY INFORMATION  
section at the beginning of this  
manual including all text under  
subheadings therein before set  
up or use of this product.  
Note: For additional information regarding  
the parts listed in the following pages,  
refer to the Assembly Diagram near  
the end of this manual.  
Installation  
1. Secure the unloaded trailer with  
wheel chocks (blocks) on a hard, flat  
surface capable of supporting the  
weight of the trailer, trailer jack and  
required tools.  
2. Raise the trailer tongue and secure it  
with two supports, one on each side  
of the trailer tongue.  
3. This Trailer Jack is designed  
specifically for use with an A-frame  
hitch. Never attempt to mount  
this Trailer Jack to a hitch or trailer  
SKU 92626  
For technical questions, please call 1-800-444-3353.  
Page 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
not specifically designed for it. An  
example of an A-frame hitch is shown  
in Figure 1.  
Assembly  
1. Raise the Trailer Jack to its  
uppermost position. Insert the Foot  
Plate (11) over the bottom of the  
Inner Tube (2).  
Figure 1  
Example of hitch (not included)  
2. Insert the Locking Pin (12) to secure  
the Foot Plate in place. See Figure 3  
below and the assembly diagram on  
page 9.  
Figure 3  
Locking Pin (12)  
4. Insert the top of the Trailer Jack up  
through the hole in the center of the  
A-frame hitch until the mounting plate  
rests against the hitch. Line up the  
holes on the mounting plate with  
the holes in the A-frame hitch. See  
Figure 2.  
Foot Plate (11)  
3. Secure the Trailer Jack to the trailer  
tongue using 3/8” diameter bolts,  
washers, nuts and lock washers (not  
included). Nylon insert nuts (not  
included) may be used instead of  
the nut and lock washer mentioned.  
Securely tighten all nuts and bolts  
into place. Bolts must be of a length  
so that at least 4 threads of the Bolt  
tip are exposed below attached Nut.  
Figure 2  
Trailer  
Tongue  
4. WARNING! Bolts must be Grade 5  
strength capable of holding the Trailer  
Jack in place while under load.  
5. Optionally, the mounting plate may be  
welded into place on the underside of  
the hitch by a certified welder.  
6. Once the Jack is mounted to the  
trailer tongue, attach the Handle (10)  
to the top of the Trailer Jack. Secure  
in place with Bolt (7), Lock Nut (8)  
and Screw (9). Securely tighten all  
hardware.  
SKU 92626  
For technical questions, please call 1-800-444-3353.  
Page 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Now that the Trailer Jack is fully  
assembled, test it by raising the  
hitch enough to remove the supports  
inserted in Step 2 on page 4.  
7. Carefully back your vehicle into place  
within a foot or two of the trailer  
tongue.  
8. Raise the Trailer Jack until the hitch  
is in a position to clear or fit over the  
hitch ball.  
Operation  
OPERATING INSTRUCTIONS  
Read the ENTIRE IMPORTANT  
SAFETY INFORMATION  
section at the beginning of this  
manual including all text under  
subheadings therein before set  
up or use of this product.  
9. With assistance, roll the Trailer or the  
vehicle into position so that the trailer  
hitch is directly over the ball hitch.  
10. Turn the Handle counterclockwise to  
lower the trailer tongue until it is firmly  
seated on the ball hitch. Tighten the  
trailer hitching mechanism.  
1. With the Handle (10) pulled out so  
that the knob is on top, turn the  
11. Continue turning the Handle  
counterclockwise until the Trailer  
Jack is fully raised.  
Handle clockwise. This will raise the  
Trailer Jack. Once the trailer is at the  
desired height, fold the Handle over  
so that the knob is facing downward.  
This will lock the Handle in place.  
2. To lower a load, turn the Handle  
counterclockwise. This will lower the  
Trailer Jack. Flip the Handle up and  
over when completed to lock the Jack  
in place.  
3. Secure the trailer in place with wheel  
chocks (blocks) on a stable, flat and  
level surface.  
4. Turn the vehicle ignition off and set  
the brake.  
5. Turn the Handle clockwise to lower  
the Foot Plate (11) to the ground.  
When the weight is carried by the  
jack, unlatch the hitch and continue  
turning clockwise until the trailer  
tongue is lifted completely off the  
hitch ball.  
6. The vehicle can now be moved in a  
forward direction. Level the trailer by  
turning the Handle.  
SKU 92626  
For technical questions, please call 1-800-444-3353.  
Page 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICING  
User Maintenance  
Procedures not specifically  
explained in this manual  
must be performed only by a  
qualified technician.  
TO PREVENT  
SERIOUS INJURY  
FROM TOOL FAILURE:  
Do not use damaged  
equipment. If abnormal noise  
or vibration occurs, have the  
problem corrected before  
further use.  
Cleaning and Maintenance  
1. BEFORE EACH USE, inspect the  
general condition of the Trailer  
Jack. Check for loose hardware,  
misalignment or binding of moving  
parts, cracked or broken parts, and  
any other condition that may affect its  
safe operation.  
2. If welded, check welds for cracks.  
3. If the Trailer Jack has been exposed  
to salt water, immediately wash off  
with fresh water. Then use a light oil  
to lubricate all moving parts.  
4. AFTER USE, wipe external surfaces  
of the tool with a clean cloth.  
SKU 92626  
For technical questions, please call 1-800-444-3353.  
Page 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLEASE READ THE FOLLOWING CAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM  
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES  
ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED  
TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS  
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT  
ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED  
TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF  
HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT  
OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.  
Parts List  
PARTS LIST  
Part  
Description  
Outer Tube  
Qty  
1
1
2
3
4
5
6
7
8
9
Inner Tube  
Nut  
1
1
Washer  
1
Bearing  
1
Bushing  
1
Bolt (M6 x 25)  
Lock Nut M6  
Screw Rod  
1
1
1
10 Handle  
1
11 Foot Plate  
12 Lock Pin  
1
1
Record Product’s Serial Number Here:  
Note: If product has no serial number, record month and year of purchase instead.  
Note: Some parts are listed and shown for illustration purposes only, and are not  
available individually as replacement parts.  
SKU 92626  
For technical questions, please call 1-800-444-3353.  
Page 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY DIAGRAM  
Assembly Diagram  
SKU 92626  
For technical questions, please call 1-800-444-3353.  
Page 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Limited 90 Day WarraLntIyMITED 90 DAY WARRANTY  
Harbor Freight Tools Co. makes every effort to assure that its products meet high  
quality and durability standards, and warrants to the original purchaser that this product  
is free from defects in materials and workmanship for the period of 90 days from the  
date of purchase. This warranty does not apply to damage due directly or indirectly,  
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities,  
criminal activity, improper installation, normal wear and tear, or to lack of maintenance.  
We shall in no event be liable for death, injuries to persons or property, or for incidental,  
contingent, special or consequential damages arising from the use of our product.  
Some states do not allow the exclusion or limitation of incidental or consequential  
damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY  
IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,  
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.  
To take advantage of this warranty, the product or part must be returned to us  
with transportation charges prepaid. Proof of purchase date and an explanation of the  
complaint must accompany the merchandise. If our inspection verifies the defect, we  
will either repair or replace the product at our election or we may elect to refund the  
purchase price if we cannot readily and quickly provide you with a replacement. We will  
return repaired products at our expense, but if we determine there is no defect, or that  
the defect resulted from causes not within the scope of our warranty, then you must  
bear the cost of returning the product.  
This warranty gives you specific legal rights and you may also have other rights  
which vary from state to state.  
3491 Mission Oaks Blvd. PO Box 6009 Camarillo, CA 93011 (800) 444-3353  
SKU 92626  
For technical questions, please call 1-800-444-3353.  
Page 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  

GrandTec Camcorder CMS 1000 User Manual
Grundig Flat Panel Television GULCD26HDIT User Manual
Hamilton Beach Iron 840121900 User Manual
Harbor Freight Tools Impact Driver 93100 User Manual
Honeywell Electric Heater V2652 User Manual
Hotpoint Clothes Dryer TVEM 70 User Manual
Hotpoint Washer WML 540 P G A K User Manual
HP Hewlett Packard PDAs Smartphones iPAQ hw6500 User Manual
Icom Stereo System IC F111S User Manual
IDEAL INDUSTRIES Power Hammer 61 095 User Manual