EXCESS CARGO CARRIER
ASSEMBLY and OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd. / Camarillo, CA93011
Copyright © 1997 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in any
shape or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
®
times. Wear a full face shield if you are producing metal filings or wood chips. Wear an ANSI
approved dust mask or respirator when working around metal, wood, and chemical dusts
and mists.
9. DO NOT ABUSE THE POWER CORD. Do not yank it to disconnect it from the receptacle.
Do not carry tools by the cord.
10. DO NOT OVERREACH. Keep proper footing and balance at all times. Do not reach over or
across running machines.
11. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer perfor-
mance. Follow instructions for lubricating and changing accessories. Inspect tool cords
periodically and, if damaged, have them repaired by an authorized technician. The handles
must be kept clean, dry, and free from oil and grease at all times.
12. DISCONNECT POWER. Unplug when not in use, before servicing, and when changing
accessories.
13. REMOVE ADJUSTING KEYS AND WRENCHES. Make it a habit to check that keys and
adjusting wrenches are removed from the tool or machine work surface before plugging it in.
14. AVOID UNINTENTIONAL STARTING. Be sure the switch is in the OFF position when not in
use and before plugging in. Do not carry any tool with your finger on the trigger, whether it is
plugged in or not.
15. OUTDOOR EXTENSIONS CORDS. When the equipment is operated outdoors, use only
extension cords intended for outside use. See chart under “Extension Cords” for the proper
AWG rating depending on the length of the cord(s) being used.
16. STAY ALERT. Watch what you are doing; use common sense. Do not operate any tool when
you are tired.
17. CHECK DAMAGED PARTS. Before using any tool, any part that appears damaged should
be carefully checked to determine that it will operate properly and perform its intended
function. Check for alignment and binding of moving parts; any broken parts or mounting
fixtures; and any other condition that may affect proper operation. Any part that is damaged
should be properly repaired or replaced by a qualified technician. Do not use the tool if any
switch does not turn on and off properly.
18. GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces such
as pipes, radiators, ranges, and refrigerator enclosures.
19. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical replace-
ment parts. Use of any other parts will void the warranty. Only use accessories intended for
use with this tool. Approved accessories are available from Harbor Freight Tools.
20. DO NOT OPERATE TOOL IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS. Read
warning labels on prescriptions to determine if your judgment or reflexes are impaired while
taking drugs. If there is any doubt, do not operate the tool.
Page 3 -- SKU: 34313
REV 09/02
Download from Www.Somanuals.com. All Manuals Search And Download.
UNPACKING
If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of
this manual.
Ref
A
N/A
B
C1
C2
D
Item Description
Receiver Mounting Bar
Hardware Bag
Detachable Side Rail
Side Rail Brace
Side Rail Brace
Bed Frame
Quantity
1
1
2
3
3
1
Caution: Be aware of the possible risk of fire and damage to property resulting from the
vehicle’s exhaust pipe pointing at the cargo put in this Cargo Carrier. Before installing the Cargo
Carrier, check to make sure that the exhaust pipe is not pointing in the direction of the cargo.
Flammable cargo can ignite from exposure to heat. Other cargo can be damaged from the heat.
Always be aware of this potential danger, and never use the Cargo Carrier if this risk exists.
ASSEMBLY
Step 1: Place all the pieces for your Excess Cargo Carrier onto a clear work area.
Step 2: Make sure the set of three holes in the RECEIVER MOUNTING BAR (#A) are oriented
vertically. Turn the RECEIVER MOUNTING BAR to properly orient it.
Step 3: Insert the RECEIVER MOUNTING BAR (#A) under the mesh screen of the BED
FRAME (#D) and between the arched Bed Frame Supports as shown in Figure 1.
Bed Frame
(#D)
Receiver
Mounting Bar
(#A)
Figure 1 — Attatching the Mounting Receiver Bar
Page 4 -- SKU: 34313
REV 09/02
REV 10/02
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Step 4: Insert two HEX BOLTS (#E) through the top of the BED FRAME and down through the
RECEIVER MOUNTING BAR as shown in Figure 2.
Hex Bolts
(#E)
Nuts
(#F)
Figure 2 — Inserting Hex Bolts
Step 5: Attach a NUT (#F) to each of the HEX BOLTS and tighten.
Detachable Side Rails
The following Steps show how to assemble the DETACHABLE SIDE RAILS (#B). These side
rails should always be in place when using the Excess Cargo Carrier.
Page 5 -- SKU: 34313
REV 09/02
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 1: Attach one DETACHABLE SIDE RAIL to the outside corners of the BED FRAME as
shown in Figure 3. Assemble with one BOLT (#G) and one NUT (#H) per corner.
Tighten the NUTS.
Bolt
(#G)
Detachable
Side Rail
(#B)
Nut
(#H)
Detachable
Side Rail
(#B)
Bolt
(#G)
Nut
(#H)
Figure 3 — Attaching Side Rails
Step 2: Place a SIDE RAIL BRACE (#C1) outside on the vertical folded edges of the DETACH-
ABLE SIDE RAIL and BED FRAME as shown in Figure 4.
Nuts
(#H)
Side Rail
Brace
(#C1)
Bolts
(#G)
Figure 4 — Attaching Center Side Rail Braces
Page 6 -- SKU: 34313
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Step 3: Assemble with two BOLTS (#G) and two NUTS (#H) using the holes in the DETACH-
ABLE SIDE RAIL and BED FRAME. Tighten the NUTS.
Step 4: Attach a SIDE RAIL BRACE (#C2) to the inside vertical folded edges of the corner of
the Carrier Assembly as shown in Figure 5. Attach with two BOLTS and two NUTS.
Tighten the NUTS.
Side Rail
Brace
(#C2)
Nuts
(#H)
Side Rail
Brace
(#C2)
Bolts
(#G)
Bolts
(#G)
Figure 5 — Attaching Corner Side Rail Braces
Step 5: Repeat Step 4 for the other corner of the Carrier Assembly.
Step 6: Repeat Steps 1 through 5 to assemble the second DETACHABLE SIDE RAIL.
Your Excess Cargo Carrier is ready for use.
Page 7 -- SKU: 34313
REV 09/02
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Step 1: Request a friend’s help to lift the Excess Cargo Carrier.
Step 2: Lift the Excess Cargo Carrier and place the RECEIVER MOUNTING BAR into the
Hitch Receiver mounted to your vehicle.
Step 3: Line up the horizontal hole in the RECEIVER MOUNTING BAR with the hole in your
Hitch. When the holes line up, place your locking mechanism through the holes to
secure the Excess Cargo Carrier.
Your Excess Cargo Carrier can be loaded with up to 500 lbs. of cargo.
Caution: The load weight must be centered or evenly distributed across the Bed Frame (D).
Always use appropriate tie-down restraints to securely attach any cargo loaded onto the Excess
Cargo Carrier before moving your vehicle any distance. Do not leave loose items on the BED
FRAME while operating the vehicle.
DO NOT EXCEED THE MANUFACTURER’S RECOMMENDED PRODUCT WEIGHT
CAPACITY. Doing so can result in personal injury and/or damage to the product.
Caution: Be aware of dynamic loading! If the vehicle hits a bump, a slight play in the receiv-
ing hitch or a movement in the load could result in a momentary dynamic loading effect that
could dramatically increase the actual load weight. This momentary dynamic loading effect
could result in damage to the Excess Cargo Carrier, damage to the load and possible personal
injury.
Note: Any load over 350 Lbs. requires a Class 3 hitch on the vehicle.
(Class 2 Hitch = 350 Lbs. maximum tongue weight)
(Class 3 Hitch = 500 Lbs. maximum tongue weight)
PARTS LIST
Item#
Description
Qty
Item# Description
Qty
A
B
C1
C2
D
Receiver Mounting Bar
Detachable Side Rail
Side Rail Brace
Side Rail Brace
Bed Frame
1
2
2
4
1
E
F
G
H
Hex Bolt M10
Nut M10
Hex Bolt M6
Nut M6
2
2
16
16
Page 8 -- SKU: 34313
REV 09/02
Download from Www.Somanuals.com. All Manuals Search And Download.
®
ASSEMBLY DIAGRAM
DISCLAIMER
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE
MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WAR-
RANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE
ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO RE-
PLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATES THE ALL REPAIRS AND PARTS REPLACE-
MENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNI-
CIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABIL-
ITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR
REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLA-
TION OF REPLACMENT PARTS THERETO.
Page 9 -- SKU: 34313
Download from Www.Somanuals.com. All Manuals Search And Download.
|