Haier Washer XQB60 C User Manual

XQB60-C  
Automatic Washing Machine  
Contents  
Before using  
Names of the parts The 2nd cover  
Safety precautions  
1
3
5
Installation and adjustment  
Install the water inlet hose  
Using process  
Preparation before washing  
Put in the laundries  
7
8
Add the detergent and softener  
Use the operation buttons  
Close the top lid  
9
Please read this manual carefully before using.  
Retain it for future reference  
10  
14  
14  
15  
Please check if the power receptacle has good earthing  
condition before using to guarantee your safety.  
Finish washing  
Disposal after washing  
The manufacturer will not bear the responsibility for  
those risks occurred from not obeying this manual.  
Trouble shooting *  
Answers to questions  
16  
17  
Picking list  
Specifications  
the back cover  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before using  
Safety precautions  
In normal usage of the washing machine,  
the power plug shall be ready to be pulled  
or plugged with hand. Be sure to pull the  
plug off and close the water faucet in  
following cases: power failure, delivering  
the machine, setting the machine idle or  
cleaning the machine. Do not plug  
or pull the power plug with wet hand.  
Please insert the power cord into special  
receptacle with rated voltage.Be sure to  
use single-phase three pins receptacle.  
The earthing terminal must be earthed  
reliably.If possible,please adopt electric  
leakage protector.  
Earth  
Do not bend, stretch, twist, bind the power cord by force,  
or reform it. Do not press or clamp it with heavy items. If the  
power cord and power plug are bad, or the receptacle is loose,  
be sure to have it replaced by the technicians of our special shop  
or our agent, or the after-sale service department for the sake  
of avoiding any risk. Keep the prong of the power plug clean.  
If dust is found on the power plug, please wipe it off with dry cloth.  
In case the washing machine is installed on  
ground with carpet, be careful not to block the  
ventilation hole with carpet.  
Do not use water with temperature  
higher than 50 inside the tub.  
The ventilation  
holes at the  
bottom  
Do not set the machine atdamp place  
like the bathroom. Never wash it with water.  
Do not put wet laundries on the control  
panel coating.  
Do not wash water-proof laundries like  
the raincoat, bikecovers, down textiles etc.  
to avoid abnormal vibrations in spinning and  
damaging the laundries.  
Do not let the machine share one receptacle with other  
electric appliances. If the power plug is damaged, or the  
plugging into the receptacle is loose, do not use it any  
more.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before using  
Safety precautions  
Do not put hand into the rotating tub. It is  
dangerous even if the rotation speed is slow.  
Take special care of the children. Keep  
children away from the washing machine  
to avoid them climbing on it.  
Do not decompose, repair or alter  
the machine by yourself.  
Do not put any hot or heavy items  
(such as the kettle with hot water) on the  
washing machine.  
Do not wash laundries with volatile  
materials (such as thinner, petrol etc.).  
Keep the machine away from direct  
sunlight and heat source like the heater.  
The handicapped or children shall not  
use the machine without care.  
To prevent the lint in the tub from blocking  
the cascade outlet and influencing the  
cascade effect, please keep the lint filter  
in good condition, and install it to proper  
position during washing. If the lint filter is  
lost or damaged, please contact the local  
after-sale service department of our  
company.  
Toprotect your laundries and washing  
machine, please take out all of the coins,  
buttons, sand, hairpin and other foreign  
materials before washing.  
Please check if the water faucet is open, and if  
the connection of the water inlet pipe is proper.  
It is suggested to use foamless washing powder.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before using  
Safety precautions  
Please install and adjust the machine according to the requirement of the manual, which is very  
important for you to operate the machine safely and properly.  
Install the lint filter  
Insert the bottom of the lint filter  
( marked with down side ) into  
the filter frame, then push the  
upper part ofthe filter in ( marked  
with up side ).(See to Figure)  
Install the bottom plate  
After opening the package, please lean the  
washing machine gently down on soft items  
(like towel cloth, blanket, etc.). Install the  
bottom plate to the bottom of the machine  
with one screw by a cross screwdriver,  
then lift the machine up gently. See to the  
figure:  
Adjust the installation position  
The largest allowable slope of the shank base  
of the machine is 2 . The slanting or rough  
ground will result in unstable running or  
stoppage of the machine. Please adjust it with  
following methods:  
Adjust the adjustable leg:  
1.To twist the adjustable leg, please first lift up the  
leg side slightly, loosen the adjustable nut, and  
then twist the leg.  
2.After adjustment, fasten the nut.  
Adjustable nut  
Fasten  
Loosen  
Adjustable leg  
High  
Low  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Beforee using  
Install the outer drain hose  
Connect the outer drain hose to the inner drain hose by using the drain hose clamp clip them.  
Remarks: The direction of the drain hose can be changed by professional person.  
Usage of the drain hose  
The drain hose shall drain smoothly  
4.If extra drain hose is needed, please  
make separate purchase. The inner  
diameter of the extra hose shall not  
less than 30mm, and the length shall  
not exceed 1.5m.  
1.The height of the drain hose shall be  
less than 10cm, or the drainage will not  
be smooth, and cost such long time that  
the machine may stop at mid way.  
2.Do not ramp or press the drain hose.  
If the drain hose is too long, cut it at mid  
point. To make smooth drainage, cut the  
front end of the hose slantingly.  
If the extra hose is too long, cut it  
either at A or at B point.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before Using  
Install the water inlet hose  
Install the water inlet pipe  
Water faucet, suitable  
water faucet, not suitable  
It is required that the front end shall be longer than 10mm.  
The outlet end surface of the faucet shall be flat and smooth. If not, please file it smooth to avoid leakage.  
Connection between the water inlet hose jointer and the water faucet  
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the  
water inlet hose component. See to Figure 1.  
2 Loosen the four screws of the water inlet hose jointer till the water faucet can be accessed. Then set the water inlet hose  
jointer on the faucet. See to Figure 2. If the faucet is too large and the jointer cannot be set on, please loosen the four  
screws and take out the bush inside the jointer. See to Figure 3.  
Water inlet hose jointer  
Screw  
Slider  
Nameplate  
Bushing  
Screw knife  
Lock level  
Water inlet hose  
Figure 1  
Figure 2  
Figure 3  
3 Fasten the four screws of the water inlet hose jointer evenly. See to Figure 4.  
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure  
to seal up the exit end face of the faucet. See to Figure 5.  
Remark: .Before installation, the threading is 4mm above the upper surface of the nut.  
After installation, the threading is 2mm above the upper surface of the nut..  
About 4mm after twisting  
About above 2mm after twisting  
Screw nut  
Figure 4  
Figure 5  
Figure 6  
Connection between the water inlet hose and the washing machine  
1 Do nottake off the water absorptioncushion. Please check  
if the cushionis dropped ordamaged each timebefore using.  
If it happensso, please dulycontact our after-sale service  
department.  
Water inlet  
hose nut  
2 Set thenut of thewater inlet hoseon the waterinlet valve jointer.  
3 Fasten thenut. Swing itgently to confirmif it's fastenedwell.  
Water absorption cushion.  
Water inlet valve jointer  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before Using  
Connection between the water inlet hose jointer and the water inlet hose  
1 Push down the slider. Plug the water inlet hose into the jointer.  
The water inlet  
hose jointer  
2 Hang the lock lever onto the jointer. Release  
the slider till a click sound is heard.  
Slider  
Locking level  
Check the connection between the water inlet hose jointer and the  
water faucet  
1.Swing the hosegently to checkif it isfastened stably.  
2.After installation, openthe faucet tocheck if it leaks water.  
3.Do not bendthe hose byforce.  
4.Each time beforeusing, please checkif the connection  
between the waterinlet hose jointerand the waterfaucet,  
and the installation of the waterinlet hoseis firm, so as  
to avoid droppingowing to improperinstallation.  
Dismount the water inlet hose  
1 Close the water faucet.  
2 Press the lock lever and push down the slider. Then pull off the  
water inlet hose. If the machine is used more than once every  
week, the water inlet hose jointer can remain on the faucet to  
avoid damaging the fastening screws.  
Lock level  
Slider  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
1Preparation before washing  
Preparation before washing  
1 Connect the water inlet hose. Open the water faucet.  
2 Confirm that the washing machine is earthed reliably.  
Then plug the power plug into the receptacle. The  
earthing terminal shall not link to gas pipeline and  
faucet water pipeline.  
3 Put down the drain hose.  
Earth  
Pay attention to the followings before washing  
Check  
if C l e a r t h e Tie the long The quantity of  
When the pulsator  
the laundries pocket. Take strips; fasten the laundries is running ,the  
have special out the coins, the buttons; shall not be too buttons of the  
requirement sand, hairpins close zippers. large. Stretch laundries may  
on washing etc.  
and loosen the cause noise. For  
laundries before t h e s a k e o f  
putting them in discretion, please  
the tub.  
put the laundries  
with buttons into  
other laundries.  
A. Check if the laundries are applicable for washing with machine.  
b. Divide the laundries that are not colorfast from other laundries.  
c. Put the laundries difficult to absorb water into water with hand.  
d. For the laundries with heavy soil, please first remove the dirt like mud or dust.  
For the parts with heavy soil, please apply detergent on them in advance, which  
can make it easier to remove the soil.  
e. For the laundries that may get lint ball and those with long fur, turn it over before  
putting in.  
f. Do not put the laundries polluted by chemicals into the washing machine directly.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
2 Put in the laundries  
The capacity of washing and spinning refer to the  
largest weight of the standard laundries under dry  
condition that can be washed or spinned in one  
cycle. Washing quantity for one cycle shall be  
less than the rated capacity.The largest capacity of  
this machine is 6.0kg.  
The thickness, size and type of the cloth will  
influence the actual washing capacity. It is  
feasible to put in suitable amount of laundries and  
the laundries can be tumbled normally in washing  
for one cycle.  
Please do not select high water level for laundries  
less than 2.0kg to avoid splashing.  
Reference weight of the laundries:  
Working suit up,down  
cotton,about 1120g  
Jeans about 800g  
Blanket  
cotton,about 900g  
blending coat  
about 800g  
Pajamas  
about 200g  
Jacket  
cotton,about  
800g  
Shirt  
cotton,about  
300g  
Single bed sheet  
cotton,about 600g  
Undershirt  
cotton,about 180g  
Socking  
blending,about 50g  
Underpants  
cotton,about 70g  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using pprocess  
3 Add the detergent and softener  
How to use the washing powder  
Not applicable for fuzzy program and reserve  
washing  
Directly dissolved in the machine:  
1.Fill in small quantity of water.  
2.Add the washing powder. Run for 30 seconds  
to dissolve it completely.  
How to use the whitener  
3.Put in the laundries. Select suitable water level.  
The instant dissolving of the washing powder:  
1.Prepare warm water of 30 and a container.  
2.Add the powder into the container while  
stirring to fully dissolve it.  
The powder is more likely to pollute the laundries  
than the detergent. Therefore please use it with  
suitable quantity.  
Fill water to decided level. Dilute the  
whitener with container. Pour it slowly into  
the washing tub.  
Do not use whitener on laundries with  
color or print as they are not colorfast.  
The whitener shall not touch the laundries  
directly.  
It is suggested not to use high sudsing detergent.  
Washing powder with poor quality or long time  
storage may be caked. Please pay attention to  
cleaning the detergent box in time.  
Refer to the user's manual for the usage  
and dosage of the whitener.  
As to whitener in powder, please dissolve  
it before using.  
Standard dosage of the detergent and water quantity  
Laundries  
quantity  
(kg)  
Common powder,  
Add 40g in each 30L water Add 25g in each 30L water  
Concentrated powder,  
Water  
quantity  
Water  
level  
About 42g  
About 67g  
High  
About 50L  
About 35g  
About 28g  
Middle  
Low  
About 56g  
About 45g  
About 42L  
About 34L  
Below 2.0  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using pprocess  
4 Use the operation buttons  
a Description of the function of the operation buttons  
Mode and meaning of the indicator  
Flash: indicating the running mode  
On: indicating the mode about to run  
Flash rapidly: indicating abnormal situation  
SELECT button  
Push it to select one or more programs from WASH  
RINSE and SPIN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using pprocess  
POWER switch button  
TER LEVEL  
WA  
Push the On/Off button toswitch on the power.  
When the poweris on, push it again to switch  
off the power.  
Select or adjust water level  
TER LEVEL  
WA  
Reset  
POWER  
High  
Middle  
Low  
ON  
OFF  
Remarks: Push the On/Off button to switch on the power.  
If the washingmachine is idle for 10 minutes, it will auto-  
matically switch off the power.  
START/PAUSE button  
PROGRAM button  
The following four programs are available for your  
option  
After the poweris switched on, push it to start  
the machine  
During working, push it to pause working.  
During pause, push it to resume working.  
Normal  
Speedy  
Gentle  
Jeans  
Common washing  
Quick washing of laundries with light soil  
Washing the woolen textiles or underwear  
Washing the large and heavy stained laundries  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using pprocess  
b Steps of using the operation buttons and description of each step.  
Attention  
TER LEVEL  
Reset  
WA  
Even there's no water in the tub, a certain period  
is required before spin starting.  
Separate the laundries that are not colorfast from  
other laundries in washing.  
POWER  
High  
Middle  
Low  
ON  
OFF  
1.Push the POWER button to switch on the power.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using pprocess  
2.Select suitable automatic program.  
After switching onthe power, the machine willset standard programautomatically. To select otherautomatic program,  
push the suitablebutton till therelative indicator ison.  
Refer to thePROGRAM button onPage 11 for theselection.  
For instance: Pushthe SPEEDY program for quickwashing of laundrieswith light soil.  
Table of Each Program  
Spin  
(minute)  
Wash  
(minute)  
Program  
Normal  
Rinse (minute)  
Total time (minute)  
About 45  
About 12  
About 3  
About 3  
About 12  
About 5  
Rinse twice (2 minutes every time)  
Spray once (1.5 minutes )  
About 3  
About 2/3  
About 3  
About 22  
About 30  
About 45  
Speedy  
Gentle  
Jeans  
Rinse twice (2 minutes every time)  
Spray twice (2 minutes every time)  
* Total time: including the normal water inlet time and drain time.  
* Spin time: the time from intermittent running to finishing  
* The washing finishing time may be influenced by the water inlet pressure.  
3.Push the PROCESS SELECTOR button to select suitable procedure.  
After switching on the power, the washing machine will set to WASH, RINSE, SPIN procedure automatically.  
It is the common procedure. Push the PROCESS SELECTOR button to select one or more procedures from  
WASH, RINSE and SPIN. Referto PROCEDURE SELECTIONMETHOD to make selection.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using pprocess  
Procedure selection method  
Contents (the lighted indicators  
indicate the programs about to run)  
Times of pushing the  
Selected procedure  
SELECT button  
Applicable circumstance  
WASH  
WASH  
WASH  
WASH  
WASH  
RINSE  
RINSE  
RINSE  
RINSE  
RINSE  
SPIN  
SPIN  
SPIN  
SPIN  
SPIN  
When the common laundries need  
washing, rinsing and spinning.  
WASH, RINSE, SPIN  
WASH  
(the washing liquid  
remains in the tub)  
Repeat using the washing liquid  
When prevent the laundries from  
corrugating, and the laundries do  
not need spinning  
WASH - RINSE  
(the rinsing liquid  
remains in the tub)  
When the laundries need rinsing  
and spinning after manual washing  
RINSE - SPIN  
When the laundries need only  
spinning after manual washing  
(first drain then spin)  
Spin  
(spin after drain)  
Push the SELECT button for 5 times, and it will resume the initial mode. It will circulate in that sequence.  
4.Switch the WATER LEVEL button to select suitable water level  
According to the capacity of the laundries, choose the three water levels High  
Middle  
Low  
After the water inlet as per the preset water level, in case additional water quantity is required, please first set  
the button to the Reset when the automatic inlet reaches the water level, you can turn to the needed water  
level.  
5.Push the START/PAUSE button  
5 Close the top lid. 6 The washing is finished.  
It beeps to indicate the  
finishing of washing  
The power will be switched off automatically after the finishing of the washing.  
If you open the top lid, the machine will stop working before spinning.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
Using process  
7 Disposal After Washing  
Cleaning the lintfilter  
The lint filter must be used during washing.  
It must be cleaned in time after each using.  
1.Take off the lint filter  
Put hand atthe indicated positon.  
Push down totake it off. (See to  
Figure 1)  
Figure 1  
2.Clean the lint  
Put it in water and cleanwhile it is  
still wet. (See to Figure 2)  
Figure 2  
3.Install the lint filter  
After cleaning, insert the bottom  
of the lint filter ( marked with  
down side ) into the filter frame,  
then push the upper part ofthe  
filter in ( marked with up side ).  
(See to Figure3)  
Figure 3  
The filter screenis likely to be blocked by foreign  
materials and influence water inlet. Pleaseclean it  
with brush frequently.  
If the cabinet is dirty, wipe it with wet soft cloth  
Do not wash with water directly.  
Wipe with neutral detergent.  
Do not wipe with thinner, petrol, alcohol, etc.  
1.After washing, close the water faucet. (If desired, dismount the water inlet hose).  
2.Do not store water in the washing machine for a long period. Drain the water completely  
after each using.  
3.Be sure to pull off the power plug before maintenance.  
4.Hang up the power cord and drain hose.  
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid  
for some time (about 1 hour), then close the top lid.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Trouble--shoootingAAnsweers to qquestions  
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns  
sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special  
maintenance department or after-sale service department of our company. Do not repair it by yourself.  
Phenomenon  
Reason  
How to solve  
The wash, rinse spin and gentle s lamps are  
flashing. The machine does not spin.  
The top lid is opened.  
Close the top lid.  
Clean the foreign material. Push  
the start button again.  
The wash, rinse, spin and jeans s lamps are flashing.  
The drainage cannot work, or is too slow.  
Is the drain hose blocked?  
Reorder the laundries. Close the top lid.  
Set the washing machine horizontally and  
then open and close the top lid once.  
The safety switch acts, and the spinning  
cannot work. The wash, spin, jeans and  
speedy s lamps are flashing.  
Are the laundries put slantingly?  
Is the machine slanting?  
Please use it when there's power supply.  
Insert the power plug tightly.  
Fill water to the preset position.  
Is there powerfailure?  
Is the powerplug inserted tightly?  
Is the waterlevel reached preset  
position?  
The machine  
Not wash  
does not act.  
Insert the powerplug tightly.  
Close the toplid.  
Set the laundriesflat.  
Is the powerplug inserted tightly?  
Is the toplid closed reliably?  
Are the laundriesset flat?  
Not spin  
Is the machine slanting?  
Are there any foreign materials?  
Are the laundries put slantingly in  
spinning?  
Adjust the machine to be even  
Remove the foreign materials.  
Reorder the laundries and close the top lid.  
There's abnormal sound inside  
the machine  
Is the screw of the water inlet hose  
jointer loose?  
Fasten the screw of the jointer properly.  
The water faucetleaks water  
Is the screw of the water inlet hose  
jointer twisted awry?  
Is the power plug plugged tightly?  
Is the water faucet opened?  
Are the POWER ON/OFF and  
Plug the powerplug tightly.  
Open the waterfaucet.  
Push the powerON/OFF button and  
START/PAUSE button.  
No water inlet.  
START/PAUSE buttons pushed down?  
Common phenomena  
Phenomena  
Explanation  
The spinning is intermittent whenit starts.  
Push the SPINbutton, but it doesn't act.  
It is tobalance the laundriesto avoid slanting.  
The program is setting thedrain time. A certain  
period is neededbefore it startsspinning.  
It is thewater remained inthe machine duringthe  
ex-factory performance inspection.  
There may be some waterflowing out ofthe drain  
hose in thefirst use ofthe machine.  
The pulsator pauses during water filling in washing and rinsing.  
It is toavoid splashing duringwater filling.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Packing list  
Quantity  
Name  
Storage position  
1 piece  
1 piece  
Inside the document bag  
Inside the document bag  
User's manual  
Lint filter  
Water inlet hose component  
1 piece  
Inside the inner tub  
Between the upper cushion of the  
washing machine package and the upper  
seal of the package carton  
1 piece  
Bottom plate  
Inside the document bag  
1 pieces  
1 pieces  
Tapping screw  
Inside the inner tub  
Inside the inner tub  
Outer drain hose  
Drain hose clamp  
1 pieces  
1 set  
Fuzzy logic automatic  
washing machine  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Model  
XQB60-C  
Rated voltage frequency  
Rated washing / spinning capacity  
220-240V ~ 50Hz  
6.0kg  
Water level/Water  
quantity (about)  
50L/High, 42L/Middle, 34L/Low  
Max water consumption  
Water inlet pressure  
About 150L (the highest water level, normal program)  
0.03MPa-0.78MPa  
Rated washing power  
Rated spinning power  
Weight  
415W  
315W  
About 33kg  
L 540 W 540 H 875  
Dimensions (mm)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Grizzly Marine Safety Devices T10722 User Manual
GVision DJ Equipment 352 User Manual
Hamilton Beach Air Cleaner 840103300 User Manual
Hamilton Watch Watch Multi Touch Watch User Manual
Honeywell Digital Camera VCC 600N P User Manual
Honeywell Humidifier HE360A1075 User Manual
Hotpoint Dishwasher HDA6009 User Manual
Hunter Fan Thermostat 42711 01 User Manual
Hunter Fan Universal Remote 99116 User Manual
IMC Networks Network Card IE IMCV T1 MUX 4 User Manual