XQB50-20
Fuzzy Logic Automatic
Washing Machine
Contents
Before using
Names of the parts.........the 2nd cover
Safety precautions ............................1
Special function introduction ............ 3
Installation and adjustment ...............3
Install the water inlet hose.................5
Using process
Preparation before washing .............7
Put in the laundries ...........................8
Add the detergent/softener ...............9
Use the operation buttons ...............10
Close the top lid ..............................14
Washing finished .............................14
Disposal after washing ....................15
Part specialized code 0030504485
Please check if the power receptacle has good
earthing condition before using to guarantee
your safety.
The product is used only in the Chinese continent..If
other countries or areas need it, please contact us.
Trouble shooting Answer to
question.........................................16
Packing list .....................................17
Please read this manual carefully before using.
The manufacturer will not take responsibility for
those risks occurred from not obeying this manual.
Retain it for future reference.
Specification..............the back cover
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Using
Safety precautions
Please plug the plug on special 220V~240 AC
receptacle.Be sure to use three phase power
receptacle. Ensurethe earthing prong of the power
receptacle is earth-ed reliably. Use a leakage
protector if possible.
In normal usage of the washing machine, the power
plug shall be ready to be pulled or plugged with hang.
Be sure to pull the plug off and close the water faucet
when occurring power failure, delivering the machine,
setting the machine idle or cleaning the machine, Do
not plug or pull the power plug with wet hand.
Earth
Do not bend, stretch, twist, bind the power cord by force, or reform it.
Do not press or clamp it with heavy items. If the power cord and power
plug are bad, or the receptacle is loose, be sure to have it replaced by
the technicians of our special shop or our agent,or the after-sales service
department to avoid any risk.Keep the prong of the power plug clean.If
dust is found on the power plug, please wipe it off with dry cloth.
In case the washing machine is installed on ground
with carpet, be careful not to block the ventilation hole
with carpet.
Do not use water with temperature higher than 50
The ventilation
holes at the bottom
Do not wash waterproof laundry like the raincoat,
bikecovers, down textiles etc. To avoid abnormal
vibrations in spinning.
Do not put the machine at damp place like the
bathroom. Never wash it with water. Do not
put wet laundries on the control panel coating.
Do not let the machine share one receptacle with other
electric appliances. If the plugging into the receptacle
is loose, do not use the plug any more.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Using
Safety precautions
Do not decompose, repair or alter the machine
by yourself.
Do not put hand into the rotating tub. It is dangerous
even if the rotation speed is slow. Take special care of
the children. Keep children away from the washing
machine to avoid them climbing on.
Do not put any hot or heavy items (such as the kettle
with hot water ) on the washing machine.
Do not wash laundries with volatile materials
(such as thinner, petrol etc.)
er
Petrol
inn
Th
The handicapped or children without care shall not
use the machine.
Keep the machine away from direct sunlight and
heat source like the heater.
To protect your laundries and washing machine,
please take out all of the coins, buttons, sand, hairpin
and other foreign materials before washing.
To prevent the lint inside the tub from blocking the
cascade outlet during washing, please keep the
lint filter in good condition, and install it to proper
position. If the lint filter is lost or damaged, please
contact the local after-sales service department of
our company.
Please check if the water faucet is open, and if the
connection of the water inlet pipe is proper. if the
drain pipe is put down.
Install
Dismantle
It is suggested to use foamless washing powder.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Special function introduction
Before Using
Eliminating foam rinse
Press the RINSE button, when the tube is on, it indicates that you have chosen the ELIMINATING FOAM RINSE PROGRAM, and
perform eliminating foam rinse firstly. Then, it will fill water continuously after the water level is high, and the foam in the tub will
overflow from the overflow inlet, and avoiding polluting the clothes again.
Memory programme
After switching on the Power, select the memory programme(the tube on).Then select appropriate time of SOAK, WASH and SPIN
and the time of rinse on need. After setting, the washing machine memorized the programme set by yourself. When switching on
the Power again, press the PROGRAM button, and select the MEMORY program, the program set by yourself will start
automatically. Using the MEMORY program, you can storage the program which meets with your individual need.
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual. It is
very important to your security and correct operating the machine.
Install lint filter
Install bottom plate
After you open the package, please lean the washing
machine gently down on soft items ( like the towel cloth,
blanket, etc. ). Install the bottom plate to the bottom of
the machine with the five screws by a cross screwdriver,
Push lint filter downward to location for
lint filter
then lift the machine up gently. See to the figure:
Ajustable foot
Front
Bottom plate
Install
Back
Screw
Soft items
Adjust the installation position
The distance that washing machine away from wall should be above 20mm. The largest allowed slope of the
shank base of the machine is 2 . The slanting or rough ground will result in unstable running or stoppage
of the machine. Please adjust it with following methods:
Confirm it's horizontal:
Hang the lead line to confirm if it is horizontal.
<2
Adjust the adjustable foot:
Adjustable nut
1.To twist the adjustable foot, please first lift up
the side of the foot slightly, loosen the adjustable
nut, and twist the foot.
2.Fasten the nut after adjustment.
Fasten
Low
Adjustable feet
Loosen
High
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Using
How to change the direction of the drain hose
1 Loosen the fastening screws of the back cover,unpack 3 Stretch out the drain hose to the right of the frame
the back cover gently, avoiding to break the clip claw.
from the groove. Fasten it in the base frame with the
drain hose support, and fasten the screws.Then hang
the hook in the drain hose, and hang the drain hose in
the hole of the cabinet. (Figure 3)
Figure 1
Back cover
( Figure 3 )
2
Take the drain hose from the cabinet, make the mouth of
4
Install the back cover. Hang the under side of the
it flat a little, dismantle the pothook, loosen the fastening
screws, dismantle the drain hose support ,and pull the drain
hose into the cabinet from the left of the base.
back cover on the cabinet firstly, then push the left
, the right tab and the upside into the cabinet.
Do not do it strongly, and fasten the screws.
(Figure 4)
Upper tab
Figure 2
Drain hose frame
Screws
Side tab
Make the mouth of the
drain hose flat, take off
the pothook.
Lower hook
( Figure 2 )
Screws
(Figure 4)
Usage of the drain hose
The drainage shall be smooth with the drain hose.
1.Never let the drain hose exceed 10cm above the
ground. If the timeof draining is too long, the washing
machine will stop in the midway.
4.If extra drain hose is needed, please make separate
purchase. The inner diameter of the extra hose shall
not less than 30mm, and the length shall not exceed
1.5m.
2.Do not step on or press the drain hose.
> 30mm
<10cm
<1.5m
5. If the extra hose is too long,cut it either at A or
at B
3.If the drain hose is too long, cut it at mid point. To make
smooth drainage, cut the front end of the hose slantingly.
B
A
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Using
Install the water inlet hose
Confirm the water faucet
Water faucet, not suitable
Water faucet, suitable
Outlet end surface
>10mm
It is required that the front end shall be longer than 10cm.
The outlet end surface of the faucet shall be flat and smooth. If not please file it
to avoid leakage.
Connection between the water inlet hose jointer and
the water faucet
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet
hose jointer from the water inlet hose component. See to Figure 1.
2.Loosen the screw till the water faucet can be accessed. Put the jointer of the water
inlet hose on the faucet. See to Figure 2. (If the faucet is too large and the jointer can
not be set on the water faucet, please loosen the four screws and take out the
bushing in the jointer. See to the figure.)
Water inlet pipe jointer
Screw
Slider
Mark label
Screwdriver
Liner
Locking lever
Water inlet pipe
Figure 1
Figure 2
Figure 3
3.Fasten the four screws evenly. See to Figure 4.
4.Take off the nameplate. Twist the fastening nut as per the indication of the figure to
seal up the outlet end surface of the faucet. See to Figure 5.
Remarks: Before installation, the threading is 4mm above the upper surface of
the nut. After installation, the threading is 2mm above the upper surface of the
nut. See to Figure 6.
About 4mm before twisting
About below 2mm after twisting
Nut
Figure 4
Figure 5
Figure 6
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Using
Connection between the water inlet hose and the
washing machine
1.Do not take off the water absorption
cushion. Please check if the cushion
is dropped or damaged before each
usage. If it happens please contact
our after-sale department immediately.
2.Put the nut of the water inlet hose on
the valve jointer.
Nut of the water inlet hose
Water absorption cushion
Jointer of the water inlet valve
3.Fasten the nut. Swing it gently to
confirm if it's suitable.
Connection between the jointer of the water inlet
hose and the water inlet hose
1.Push down the slider. Insert the
water inlet hose into the jointer.
2.Hang the lock lever to the jointer.
Release the slider till a click
sound is heard.
Jointer of the water
inlet hose
Locking lever
Slider
Check the connection between the jointer of the
water inlet hose and the water faucet
1.Swing the hose gently to confirm if it is fastened stable.
2.After installation, open the faucet to check if it leaks.
3.Do not bend the hose with overstrain.
4.Before each usage please check if
the connection between the jointer
of the water inlet hose and the water
faucet, and the installation of the
water inlet hose are firm, so as to
prevent dropping from improper
Installation position.
Dismantle the water inlet hose
1.Close the water faucet.
2.Press the locking lever. Push down the slider. Then
pull of the water inlet hose. If the machine is used
more than once every week, the jointer of the water
inlet hose can be kept on the faucet to prevent
damaging the fixing screw.
Locking lever
Slider
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Using process
1 Preparation before washing
Preparation before washing
1. Connect the water inlet hose.
2. Confirm that the washing machine is earthed
reliably. Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.
3.Put down the drain hose.
Pay attention to followings before washing the laundries
Confirm if there's
special requirement Take out the coins, and zippers.
for the laundries. sand, hairpins etc.
Clear the pocket.
Fasten the buttons The quantity of the
When the pulsator is
running, the buttons of
laundries shall not
exceed the rated value. the laundries may cause
The big laundries like noise. For the sake of
the jeans shall be put discretion, please put
in loosely.
the laundries with
buttons into other
laundries.
a. Check if the laundries are applicable for washing with the machine.
b. Divide the laundries with unfast color from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil,
please apply detergent in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn it over before putting in.
f. Do not put those laundries polluted by chemicals directly into the washing machine.
g. For those small laundries and those may get twisting or worn, and woolen/fur laundries, please put them into
mesh bag for washing.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Using process
2 Put in the laundries
The capacity of washing and spinning of the
machine refer to the largest weight of the standard
laundries under dry condition (as per the
laundries stipulated in the A2 Attachment of
GB4288-1992 standard) that can be washed or
spun in one time. One time washing quantity
shall be lower than the rated capacity. The largest
capacity of this machine is 5.0kg.
The thicknesses, size, type of the cloth will influence
the actual washing capacity. It is suitable for one
time washing to put in reasonable amount of
laundries and the laundries can be turned round in
washing.
Do not select 4 water level or above for laundries
smaller than 1.0kg, so as to avoid splashing of water.
Reference weight of the laundries:
working suit(up,down)
(cotton, about 1120g)
Jeans(about 800g)
Blanket
cotton, about 900g
blending coat
(about 800g)
Pajamas
(About 200g)
Jacket
(cotton, about
800g)
Shirt
(cotton, about
300g)
single bed sheet
(cotton, about 600g)
Undershirt
(cotton, about 180g)
Socking
(blending, about 50g)
Underpants
(cotton, about 70g)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Using process
3 Usage of the detergent
Softner dispenser
Add the detergent and softener into the box
directly as indicated in the left figure.
After adding, please close the detergent box.
See to following table for the dosage of the
detergent.
Location for
concentrated powder
Detergent box
How to use the washing
powder
Direct dissolved in the machine
1.Fill water to "Low" water level.
Control panal
2.Add the power. Run for 30 seconds to
dissolve it completely.
3.Put in the laundries. Select suitable water level.
The instant dissolving of the washing powder:
1.Prepare warm water of 30 C and a container.
2.Add the powder while stirring to fully
dissolve it.
Location for liquid bleacher
How touse thewhitener
The powder is more prone to pollute the
laundries than the detergent. Therefore
please use it with proper quantity.
It is suggested not to use high-sudsing
detergent.
Washing powder with poor quality or not used
for a long period may get blocked. Please
clean the detergent box in time.
Fill water to decided level. Dilute the whitener
with container. Pour it slowly into the washing
tub.
Avoid using whitener on laundries with color
or pattern as they are prone to lose color.
The whitener shall not touch the laundries
directly.
Refer to the user's manual for the usage and
quantity of the whitener.
For powder whitener, please dissolve it before
use.
Different washing powders have different
dosage. Please refer to the usage manual of
the washing powder for the details.
Water level, water quantity and the choice of usage
quantity of the detergent
Concentrated
powder
(Add 25g in each
30L water)
Common powder
Laundries
quantity(kg)
Water level
Water quantity
(Add 40g in each
30L water)
About 42L
About 38L
About 56g
About 50.5g
About 35g
About 31.5g
10
9
5.0~3.5
2.5~3.5
About 35L
About 33L
About 46.5g
About 44g
About 29g
About 27g
8
7
About 31L
About 28L
About 41g
About 37g
About 26g
About 23g
6
5
1.5~2.5
0.5~1.5
4
3
About 26L
About 23L
About 34.5g
About 30.5g
About 22g
About 19g
About 18L
About 15L
About 24g
About 20g
About 15g
About 12.5g
2
1
Below 0.5
9
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Use the operation buttons
Using process
Description of the function of the buttons
A
Indicator light of procedure
During the transmitting, the digital tube of SOAK is off,
the digital tube of WASH displays "--",the digital tube of
RINSE displays "2",and the digital tube of SPIN displays
"4".
Mode and meaning of the indicator light
Flashing: indicate the running program
On: indicate the program about to run, or indicate
the selected mode
During the program, the digital tubes display appropriate
time.
SOAK
RINSE
WASH
SPIN
WATER
LEVEL
SOAK button
WASH button
SPIN button
RINSE button
Press the RINSE button to set the process
of RINSE.
During the NORMAL or COTTON program,
press the RINSE button to setdifferent
Press the SPIN button to set the
process of SPIN.
During the NORMAL or COTTON
program, press the SPIN button to
set different time of spin(from 0
to 9 minutes)
During the GENTLE JEAN and
FIBRE program, press the SPIN
button to select the process of
spin, but not to change the time
of spin.
During the QUICK program, press
the SPIN button, the washing
machine does not respond.
Press the WASH button to set
the process of WASH.
Press the SOAK button to set
the process of SOAK.
During the NORMAL or COTTON
program, press the WASH button
to set different time (from 0 to 25
minutes)
During the NORMAL or COTTON
program, press the SOAK button
to set different time (
times(1
2
3
4 times).
When the tube
is on, it indicates that you have chosen the
ELIMINATING FOAM RINSE PROGRAM,
and perform eliminating foam rinse firstly.
Then, it will fill water continuously after the
water level is high, and the foam in the
tub will overflow from the overflow inlet,
and avoiding polluting the clothes again.
During the GENTLE JEAN or FIBRE
program, press the RINSE button to selec
rinse process,but not to change the times
10 20 30 40 minutes)
During the JEAN or FIBRE
program, press the SOAK button
to select process, but not to
change the time for soaking.
During the GENTLE or QUICK
program, press the SOAK button,
the washing machine does not
respond.
During the JEAN or FIBRE
program, press the WASH button
to select process, but not to
change the time for washing.
During the GENTLE or QUICK
program, press the WASH button,
the washing machine does not
respond.
of rinse.
During the QUICK program, press the
RINSE button,the washing machine does
not response.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using process
ON/OFF button
Indicator light of RESERVE and TIME REMAINED
During the transmitting, it displays "--"
Press the ON/OFF button to switch on the power
After the power is on,another press will switch off the power.
After the power is on, if not press the START/PAUSE button,
the washing machine will be shut-off 5 minutes later
automatically.
During the process of reserve, it displays reserve time(hours)
When the program starts, it displays time remained(minutes).When the total
time exceeds 99 minutes, if "A " represents 100 minutes, "b " represents
110 minutes, then A3 equals 103 minutes.
If there are abnormal phenomenon, it displays abnormal signal.
No.16
START/PAUSE button
After the power is on,press the START/PAUSE button,
tha washing machine will start
Pressing the button in running will cause pausing.
In pausing, press it again to restart
XQB50-20
POWER
ON/OFF
START
PAUSE
Reserve(hours later)
PROGRAM
RESERVE
PROGRAM button
TER LEVEL button
WA
VE button
RESER
The following automatical program are available.
The GENTLE SPIN program cooperates with the NORMAL
and GENTLE program in washing.
The washing machine can check laundries automatically.
After laundries the level can be set automatically. The
auto-set water level are "4","6","8","10".
Press the knob and you
can seslect 2-24h reserve
end time.
You can select water level by yourself.After the washing
machine started working, it will not set the water level
again,you must press the ON/OFF button to set again.
If there is water remained in the tub, it can not perform
laundries check, and will display water level "6". If you put
wet laundries, it may display "10".
Programs
NORMAL
Application
Normal washing
When the RESERVE
starts, press and hold the
knob, it will display
the reserve mode.
COTTON
JEAN
For cotton clothes
For bigger and thicker clothes
For clothes made from fibre
If you select "Fast" program, the water level will
be set to "2" automatically. When it is reached, then
machine will inlet water along with washing, and the "4"
indicator flashes, till "4" is reached. Then it stops inlet
water, display "4",and perform normal washing.
During the WASH and RINSE program, press the
WATER LEVELto supply water, till you loose hand or
the water reaches the overflow level, it stops supplying water.
FIBRE
GENTLE
GENTLE SPIN
For woolen or underpants
10 minutes fast washing
QUICK
Memory and usage of the self-edit program
Normal washing and spinning gently
MEMORY
NORMAL
GENTLE SPIN
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using process
After switching on the power, the machine will set to wash-rinse-spin program automatically. That is the
most common program. To select other program, Push SOAK, WASH, RINSE and SPINbutton to select
one or more programs among soak/wash/rinse/spin. After switching on the power button, ifone of the
WASH, RINSE, SPIN button is pushed firstly, then the digital lamps will go out
automatically, and the process procedure is stopped . For example, if the Spin button is pushed firstly,
the machine will set to SPIN program automatically.
Attention
Even there's no water in the tub, the spinning will start
after a certain period.
Do not use the SOAK program for the woolen laundries.
Wash the laundries that are prone to lose colors
separately from other laundries.
The pulsator will not rotate unless the water is filled to
selected water level.
The soak program can be used as fitting of the STANDARD , COTTON, JEANS and FIBRE automatic
programs. Soak with slight stirring before wash.
After running, you can set programme in the SOAK and WASH mode, and the process of SPIN in the
RINSE mode, but can not set in other conditions.
WATER LEVEL
4 Push the WATER LEVEL button to select
suitable water level
SELECTION
When the power is switched on, the washing machine will check the cloth automatically. After that,
the water level is set automatically. To select other water level, push the button. Refer to the
Standard usage quantity of the detergent and water quantity in Page 9 and WATER LEVELSELECTION in
page 11 for the selection.
Page 9
Page 11
Time list of each program WITHOUT SELF-EDIT PROGRAM
Total time(min)
Rinse
(min)
Spin
(min)
Wash
(min)
Water
leve
Program
With SOAK
Without SOAK
STANDARD
Rinse twice, each about 2-3
Rinse thrice, each about 2-3
Rinse twice, each about 4-5
Rinse twice, each about 2-3
Rinse twice, each about 2-3
Rinse once, each about 2
COTTON TEXTILE
JEANS
CHEMICAL FIBER
GENTLE
QUICK WASH
MEMORY
Rinse 0-4 times,each about2-3
Rinse twice, each about 2-3
STANDARD
GENTLE SPIN
Download from Www.Somanuals.com. All Manuals Search And Download.
Using process
Total time: including the normal water inlet time and drain time.
*
The total washing time may be influenced by the water inlet pressure and water level.
Spin time: the time from intermittent running to finishing
When selecting SOAK program, first soak for 10-40 minutes, then do wash,
rinse, spin.
When selecting QUICK WASH program, wash, rinse and spin are set automatically.
*
*
*
*
*
RESERVATION
5 Push the RESERVATION button to
select suitable reserve program
When the power is switched on, the reservation program is disabled automatically. If you need to finish the
washing in reserved time, please push the RESERVATION button to select suitable program. Refer to the
RESERVATION in Page 11 for selection.
Page 11
Confirm the reservation program
When the reservation program is started, pressing the button,
the numeral tube displays the reserved hours to the wash
cycle end. The point light flashes to indicate in-reservation.
To change the running program or cancel reservation,
you have to switch off the power and make new
selection.
The washing will finish
about 18 hours later
START
PAUSE
6 Push the START/PAUSE button
5 Close the top lid
If you open the top lid, the machine will stop
working except for water filling and spinning
6 Washing finished
The power will be switched off automatically
after the finishing of the washing.
After Finishing wash,
alarm automatically
Download from Www.Somanuals.com. All Manuals Search And Download.
Using process
7 Disposal after washing
After using, please clean the lint and foreign materials of the lint filter etc. in time. Otherwise, it may influence
your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
Clean the detergent box and set it on the control panel
seat.
The method of dismantle:Push it up aslant and gently.
The method of install : install it upwards and aslant,
then push it in .
The lint filter must be used during washing.
It must be cleaned in time after each using
Lint filter:
1 pull upward to dismantle lint filter;
2 push downward to install lint filter;
3 please clean lint filter after wash.
Install
Dismantle
Dismantle & Install
Clean
Dismantle
Install
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
The filter screen of the water inlet valve is likely to
be blocked by foreign materials and influence the
water inlet. Please clean it with brush every two
months.
Wipe it with neutral detergent.
Do not wipe it with thinner, petrol, alcohol etc.
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.
3.Be sure to pull off the power plug before maintenance.
4.Hang up the power cord and drain hose.
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time
(about 1 hour), then close the top lid.
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble-shooting Answer to question
(If there's a breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns
sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special
maintenance department or after-sale service department of our company. Do not repair it by yourself.
Phenomena
Reason
The top lid is not closed
Is the drain hose upended?
Is the drain hose blocked by foreign
material?
How to settle
Close the top lid
The digital tube displays "E0”
The draining does not work, or the
speed of draining is too slow. The digital
tube displays "E1" and it rings.
Put down the drain hose.. Open
and close the top lid once.
Clean the foreign material. Open
and close the top lid once.
It stops running during spin. The
digital tube displays "E2" and it rings.
The top lid is not closed
Close the top lid
The safety switch acts. The
spinning cannot work (after
twice revising). The digital
tube displays "E3" and it rings.
Re-order the laundries. Close the top lid.
Are the laundries put slantingly?
Is the machine slanting?
Level the machine in right position.
Open and close the top lid once.
Is the water faucet open or is
there water supply failure?
It does not do water inlet or
the speed is slow (the water
level is not reached after 15
minutes). The digital tube
displays "E4" and it rings.
Open the water faucet. Open and close
the top lid once.
Clean the water inlet valve. Open and
close the top lid once.
Open and close the top lid once.
Is the water inlet valve is
blocked
Is the water pressure too low?
Please contact the after-salesservice
department.
The digital tube displays "E6".
The water level sensor is failure.
Is there power failure?
Please use it when there's power supply.
Insert the power plug tightly.
Is the power plug inserted tightly?
Is the water level reached preset
position?
Not wash
Fill water to the preset position.
The machine does
not act
Is the power plug inserted tightly?
Is the top lid closed reliably?
Are the laundries set flat?
Is the power plug inserted tightly?
Is the top lid closed reliably?
Are the laundries set flat?
Not spin
Is the machine slanting?
Are the laundries put slantingly in
spinning?
Are there any foreign materials?
Adjust the machine to be even
Reorder the laundries and close the top
lid.
There's abnormal sound
inside the machine
Remove the foreign materials.
Is the screw of the jointer of water
inlet hose loose or awry?
Fasten the screw of the jointer properly.
The water tap leaks
Common phenomena
Phenomena
Explanation
The spinning is intermittent when it starts.
Pause during washing.
Balance the laundries to avoid slanting.
supplemental water filled after fabric sensor has checked
fabric (about 48 seconds)
The program is setting the drain time. Some
time is needed before it starts spinning.
Select spin, but it doesn't work.
The pulsator pauses during water inlet in
wash and rinse.
It is to avoid splashing during water inlet.
There may be some water flowing out of the
drain hose in the first use of the machine.
It is the water remained in the factory
inspection of performance.
Download from Www.Somanuals.com. All Manuals Search And Download.
Packing list
Name
Quantity
One
Storage position
Inside the document bag
User's manual
Inside the document bag
Inside the document bag
Inside the accessory bag
One
Warranty card
Lint filter
One
One
Components of the
water inlet hose
Between the upper cushion of the
washing machine package and the
upper seal of the package carton
Bottom plate
One
Inside the accessory bag
Tapping screws
Five
One
Fuzzy logic automatic washing
machine
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Specification
Model
XQB50-20
Rated voltage frequency
Rated washing / spinning capacity
Water level/Water quantity (about)
Max water consumption
Injection pressure
220V-240V/ 50Hz
5 .0kg (weight of standard dry cloth)
1/15L 2/18L 3/23L 4/26L 5/28L
6/31L 7/33L 8/35L 9/38L 10/42L
About 126L(Highest water level; STANDARD program)
0.03Mpa~0.78Mpa
Rated washing power
Rated spinning power
Weight
350W
255W
About 25kg
Dimension
L 537 mm W 520 mm H 890 mm
Download from Www.Somanuals.com. All Manuals Search And Download.
|