Haier Washer WM6002A User Manual

WM6002A  
Computerized Full-auto  
Washing Machine  
TWO DRIVE  
TWO 50% CONSUMPTION SAVER  
CONTENTS  
Before using  
Names of the parts.............the 2nd cover  
Safety precautions .............................................1  
Installation and adjustment .........................3  
Install the water inlet hose............5  
Using process  
Preparation before washing ...............7  
Put in the laundries .............................8  
Put in the detergent ............................9  
Use the operation buttons ...................10  
Close the top lid .................................14  
Finish washing ...................................14  
Disposal after washing .........................15  
Trouble shooting..............................16  
Packing list.....................................17  
Specification................the back cover  
Please read this manual carefully before using.  
Retain it for future reference.  
Please check if the power receptacle has good earthing  
condition before using to guarantee your safety.  
The manufacturer will not take responsibility for those  
risks occurred from not obeying this manual.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before Using  
Safety precautions  
In normal usage of the washing machine, the power  
plug shall be ready to be pulled or plugged with hand.  
Be sure to pull the plug off and close the water faucet  
when occurring power failure,delivering the machine,  
setting the machine idle or cleaning the machine,Do  
not plug or pull the power plug with wet hand.  
Please plug the plug on special 220-240V AC receptacle.  
Be sure to use three phase power receptacle.Ensure  
the earthing prong of the power receptacle is earth-  
ed reliably.Use leakage protector if possible.  
earth  
Do not bend, stretch, twist, bind the power cord by force, or reformit.  
Do not press or clamp it with heavy items. If the power cord and power  
plug are bad, or the receptacle is loose, be sure to have it replaced by  
the technicians of our special shop or our agent,or the after-sales service  
department to avoid any risk.Keep the prong of the power plug clean.If  
dust is found on the power plug, please wipe it off with dry cloth.  
In case the washing machine is installed on ground  
with carpet, be careful not to block the ventilation hole  
with carpet.  
Do not use water with temperature higher than 50  
The ventilation  
holes at the bottom  
Do not wash water-proof laundry like the raincoat,  
bikecovers, down textiles etc. To avoid abnormal  
vibrations in spinning and damages to the laundries.  
Do not put the machine at damp place like the  
bathroom. Never wash it with water. Do not  
put wet laundries on the control panel coating.  
Do not let the machine share one receptacle with other  
electric appliances. If the power plug is damaged, or  
the plugging into the receptacle is loose, do not use  
the plug any more.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before Using  
Safety precautions  
Do not put hand into the rotating tub.It is dangerous  
Do not decompose, repair or alter the machine by  
even if the rotation speed is slow. Take special care of  
the children. Keep children away from the washing  
machine to avoid them climbing on.  
yourself.  
Do not put any hot or heavy items (such as the  
kettle with hot water) on the washing machine.  
Do not wash laundry with volatile materials  
(such as thinner, petrol etc.).  
Benzene  
Keep the machine away from direct sunlight and  
heat source like the heater.  
The handicapped or children without care shall not  
use the machine.  
Please keep the lint filter in good condition, and  
install it to proper position during washing. If the  
lint filter is lost or damaged,please contact the local  
after-sales service department of our company.  
To protect your laundries and washing machine,  
please take out all of the coins, buttons, sand, hairpins  
and other foreign materials before washing.  
Install  
Please check if the water faucet is open, and if the  
connection of the water inlet pipe is proper.  
It is suggested to use foamless washing powder.  
Dismantle  
Dismantle  
Install  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before Using  
Installation and adjustment  
Please install and adjust the machine according to the requirement of the mannual.  
It is very important to your security and correct operating the machine.  
Install the inner cover and lint filter  
1.Open the top lid of the washing machine.  
Outer tube cover  
Inner cover shaft  
2.Put the inner cover component on the outer tub cover, aiming  
the inner cover shaft to the installation hole of the corresponding  
outer tub cover shaft groove.  
3.Firstly insert the inner cover shaft of one side into the correspon  
-ding outer tub cover shaft groove, then push the another inner  
cover shaft into the corresponding outer tub cover shaft groove.  
Please install to designated position to guarantee there are no  
Inner cover  
dropping or abnormal sound in opening and closing of the inner  
Install the lint filter  
cover, and the operation shall be smooth. Do not dismount the  
inner cover component after washing.  
4.Install the lint filter in the balance ring.(See to the right figure)  
Install the bottom plate  
After opening the package, please lean the washing  
machine gently down on soft items (like towel cloth,  
blanket, etc.). Installthe bottom plate to the bottom of  
the machine with eight screws by a cross screwdriver,  
then lift the machine up gently. (See to the figure)  
Back  
Front  
bottom plate  
Soft object  
Screw  
Adjust the Installation position  
The washing machine away from wall should be overrun 20mm.The largest allowable slope of the shank base of  
the machine is 2 .The slanting or rough ground will result in unstable running or stoppage of the machine.  
Please adjust it with following methods:  
Confirm it's horizontal:  
Hang the lead line to check if it is  
horizontal.  
Adjust the adjustable leg:  
1 .To twist the adjustable leg, please first lift up the  
side of the leg slightly, loosen the adjustable nut,  
and twist the leg.  
the adjustable nut  
Fasten  
Loosen  
High  
2 . After adjustment, fastenthe nut.  
the adjustable foot  
Low  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before Using  
How to change the direction of the drain hose  
1. Dismount the back cover of the washing machine.  
2. Put down the drain hose. Take off the drain hose  
frame. As indicated in Figure 1, put the drain hose  
into the cabinet. Then put one hand into the cabinet  
to nip the claw of the drain hose bushing to release  
the claw from original position. Take off the drain  
hose bushing with the other hand. (As indicated in  
Figure 2 and 3).  
3. Dismount the protecting cover of the drain  
outlet at the other side ( method the same as  
the drain hose bushing). Install the drain hose  
bushing as per indicatedin Figure 4.  
4. Extend the drain hose from the other side.  
Fix the drain hose onto the cabinet with the  
drain hose rack. (As indicatedin Figure 5)  
••••• •••• ••••••••  
drain hose  
drain hose bushing  
Fi gur e 4  
Fi gur e 5  
dr ai n hose bushing  
hose frame  
drain  
drain protecting cover  
Fi gur e 2  
hose bushing  
cabinet  
nner  
Push  
g
Fi ure  
1
i
drain  
t ake off  
gu  
hose bushing claw  
Push  
re  
Fi  
3
Fi gur e  
6
Attention: To guarantee the proper installation, it is suggested to have the direction changing of drain  
hose performed by the after-sales service technicians of our company.  
Useage the drain hose  
The drainage shall be smooth with the drain hose.  
If extra drain hose is needed, please make separate  
The height of the drain hose shall be less than  
purchase. The inner diameter of the extra hose shall  
10cm, or the drainage will not be smooth, and cost  
not less than 30mm, and the length shall not exceed  
such long time that the machine may stop at mid  
1.5m.  
way.  
> 30mm  
Do not step on or press the drain hose.  
<1.5m  
<10cm  
If the extra hose is too long,cut  
it either at A or at B point.  
If the drain hose is too long, cut it at mid point. To make  
smooth drainage, cut the front end of the hose slantingly.  
B
A
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before Using  
Install the water inlet hose  
Confirm the water faucet  
water faucet, suitable  
water faucet, not suitable  
The exit end face of the faucet  
It is required that the front end shall be longer than 10mm.  
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.  
Connection between the water inlet hose jointer and the water faucet  
Use the newwater inlet hoseprovided with themachine to connectto the waterfaucet.Old hose sets  
should not bereused.  
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the  
water inlet hose component. See to Figure 1.  
2 Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.  
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen  
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,  
otherwise it may leak water. See to Figure 3.)  
water inlet hose jointer  
Screw  
Slider  
Sign plate  
Bushing  
Lock lever  
Screw knife  
water inlet hose  
Figure 2  
Figure 3  
Figure 1  
3.Fasten the four screws evenly. See to Figure 4.  
4 Take off the sign plate. Twist the fastening nut as per the indication of the figure  
to seal up the exit end face of the faucet. See to Figure 5.  
remark: Before installation, the threading is 4mm above the upper surface of the nut.  
After installation, the threading is 2mm above the upper surface of the nut..(see to figure 6)  
About 4mm before twisting  
About less than 2mm after twisting  
Screw nut  
Figure 6  
Figure 5  
Figure 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before Using  
Connection between the water inlet hose and the washer  
1.Do not take off the water absorption cushion. Please check if the  
cushion is dropped or damaged before each usage. If it happens  
please contact our after-sale department immediately.  
nut of thewater  
inlet hose  
2 Put the nut of the water inlet hose on the valve jointer.  
3 Fasten the nut. Swing it gently to confirm if it's suitable.  
water absorption  
cushion.  
jointer of the  
water inlet valve  
Connection between the jointer of the water inlet hose  
and the water inlet hose  
1.Push down the slider. Insert the water inlet hose into the jointer.  
the jointer of the  
water inlet hose  
2 Hang the lock lever to the jointer. Release the slider till a click  
sound is heard.  
Slider  
Locking lever  
Check the connection between the jointer of the water inlet hose  
and the water faucet  
1.Swing the hose gently to confirm if it is fastened stable.  
2.After installation, open the faucet to check if it leaks.  
3.Do not bend the hose with overstrain.  
4.Before each usage please check if the connection  
between the jointer of the water inlet hose and the  
water faucet, and the installation of the water inlet  
hose are firm, so as to prevent dropping from  
improper installation position.  
Dismantle the water inlet hose  
1. Close the water faucet.  
2. Press the locking lever. Push down the slider. Then pull of the water inlet  
hose.  
Locking level  
Slider  
If the machine is used frequently, the jointer of the water inlet hose can be  
kept on the faucet to prevent damaging the fixing screw.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
1 Preparation before washing  
Preparation before washing  
1.Connect the water inlet hose.  
2.Confirm that the washing machine is earthed  
reliably . Then insert the power plug into the  
receptacle. Do not connect the earth terminal  
to the gas pipe and tap water pipe.  
3.Put down the drain hose.  
Pay attention to followings before washing the laundries  
Confirm if there's  
special requirement Take out the coins , and zippers.  
for the laundries. sand,hairpins etc.  
Clear the pocket.  
Fasten the buttons The quantity of the When the pulsator is  
laundries shall not running ,the buttons of  
exceed the rated the laundries may cause  
value. The big noise. For the sake of  
laundries like the discretion ,please put  
jeans shall be put  
in loosely.  
the laundries with  
buttons into other  
laundries.  
a. Check if the laundries are applicable for washing with machine.  
b. Divide the laundries with unfast color from other laundries.  
c. Put those laundries difficult to absorb water into water with hand.  
d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil,  
please apply detergent in advance, which can make it easier to remove the soil.  
e. For those laundries that may get lint ball and those with long fur, turn it over before putting in.  
f. Do not put those laundries polluted by chemicals directly into the washing machine.  
g. For those small laundries and those may get twisting or worn, and woolen/fur laundries, please put them into  
mesh bag for washing.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
2 Put in the laundries  
The capacity of washing of the machine refer to the  
largest weight of the standard laundries under dry  
condition that can be washed in one time. Laundries  
quantity in one washing cycle shall be lower  
than the rated capacity. The largest capacity of  
this machine is 6.0kg.  
The thickness ,size , type of the cloth will influence the  
actual washing capacity. It is suitable to put in  
reasonable amount of laundries and the laundries can  
be turned round in washing for one time washing.  
Do not select above"4" water level for laundries less  
than 1.0kg ,so as to avoid splashing of water.  
Reference weight of the laundries:  
working suit up,down  
cotton,about 1120g  
jeans about 800g  
blanket  
cotton,about 900g  
coat with blended  
cloth (about 800g)  
pajamas  
about 200g  
jacket  
cotton,about  
800g  
shirt  
cotton,about  
300g  
single bed sheet  
cotton,about 600g  
undershirt  
cotton,about 180g  
socking  
blending,about 50g  
underpants  
cotton,about 70g  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
3 Put in the detergent  
Put the washing powder and softener into the detergent box  
directly as indicated in the left figure.  
Access for detergent and washing powder  
After that, please close the detergent box.Refer to the following  
list for the usage of the detergent : standard dosage of the  
detergent and the water quantity.  
Access for softerner  
How to use the washing powder  
Directly dissolved in the machine (not applicable for fuzzy  
program and reserve wash)  
1.Fill small quantity of water.  
Detergent box  
2.Add the power.Run for 30 seconds to dissolve it completely.  
3.Put in the laundry. Select suitable water level.  
The instant dissolving of the washing powder:  
1.Prepare warm water of 30 and a container.  
2.Add the powder while stirring to fully dissolve it.  
In selecting the super quick program, it is suggested to adopt  
liquid detergent instead of washing powder to guarantee the  
washing effect.  
The powder is more prone to pollute the laundry than the  
detergent. Therefore please use it with suitable quantity.  
It is suggested not to use high sudsing detergent.  
Washing powder with poor quality or long time storage  
maybe caked. Please pay attention to cleaning the  
detergent box in time.  
How to use the whitener  
Fill water to decided level .Dilute the whitener with  
container. Pour it slowly into the washing tub.  
Avoid using whitener on laundries with colour or  
pattern as they are prone to lose colour.  
The whitener shall not touch the laundries directly.  
Refer to the user's manual for the usage and  
quantity of the whitener.  
For powder whitener, please dissolve it before use.  
Standard dosage of the detergent and water quantity  
Laundries  
Common powder,  
Concentrated powder,  
Water  
quantity  
Water  
level  
quantity  
(kg)  
Add 40g in each 30L water Add 25g in each 30L water  
About 50L  
About 47L  
About 67g  
About 63g  
About 42g  
About 39g  
About 45L  
About 42L  
About 60g  
About 56g  
About 37g  
About 35g  
About 38L  
About 32L  
About 51g  
About 43g  
About 32g  
About 27g  
About 28L  
About 24L  
About 37g  
About 32g  
About 23g  
About 20g  
About 20L  
About 16L  
About 27g  
About 21g  
About 17g  
About 13g  
Below 0.5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
4 Use the operation buttons  
Description of the function of buttons  
Digital tube  
Mode and meaning of the indicators  
During sensing, it displays  
During operation of programs, it displays the  
remained time (minute) or remained times of  
the corresponding procedure  
Flashing: indicate the running program  
On: indicate the program about to run, or  
indicate the selected mode  
SOAK  
WASH  
RINSE  
SPIN  
•• button  
RINSEbutton  
Push the soak button to set the soak procedure.  
During normal and jean programs, push the soak  
button to set different soak time (10, 20, 30, 40 minutes)  
During chemical fibre and cotton programs, push the  
soak button to select soak procedure, but the soak time  
cannot change.  
Push the rinse button to set the rinse procedure.  
During normal and jean programs, push the soak  
button to set different rinse times ( 0, 1, 2 times)  
During fibre , cotton,woollen and silk programs,  
push the soak button to select rinse procedure, but the  
rinse times cannot change.  
During quick , posthastet programs, push the soak  
button, the machine have no reaction.  
During quick , posthaste , woollen and silk programs,  
push the soak button, the machine have no reaction.  
During normal program, the machine is set to save water  
program. If you push the rinse button before starting  
operation, it will change to water storage rinse program.  
• •button  
Push the wash button to set the wash procedure.  
During normal and jean programs, push the wash  
button to set different wash time (from 0 to 16minutes)  
During fibre , cotton, woollen and silk programs,  
push the wash button to select wash procedure, but the  
wash time cannot change.  
SPINbutton  
Push the spin button to set the spin procedure.  
During normal and jean programs, push the spin  
button to set different spin time (from 0 to 6 minutes)  
During fibre , cotton, woollen and silk programs,  
push the spin button to select spin procedure, but the spin  
time cannot change.  
During quick,posthaste programs,push the wash button  
the machine have no reaction.  
During quick ,posthaste programs, push the spin button,  
the machine have no reaction.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHILD LOCKfunction  
Push and hold the water level button and spin button, then push down  
the power on/off button. The digitron displays CL . You can continue  
setting desired washing procedures. After setting, push down the  
start/pause button. The child lock function is activated. All of the buttons  
are locked and cannot make selection.  
• • • •  
Push the ON/OFF button to switch on the power.  
When the power is on, push it again to switch off  
the power.  
button  
Release the child lock function: push down the water level and spin button  
at the same time for more than 1 second. After a beepsound, the child lock  
function is released.  
Reserve/remain time indicator digitron  
Push the ON/OFF button to switch on the power.  
If the start/pause button is not pushed, the  
washing machine will automatically switch off the  
power after 5 minutes.  
During sensing, it displays --  
During reserve procedure, it displays the remained reserve time (in hours)  
During operation of programs, it displays the remained time (minutes).  
If the remained time exceeds 99 minutes, it adopts A at tens place to  
represent 100 minutes, b to represent 110 minutes. For instance, A3  
represents103 minutes.  
WM6002A  
In case of abnormal phenomenon, it displays  
Page16  
the abnormal symbol (see to Page 16)  
NORMAL  
QUICK  
POSTHASTE  
JEAN  
POWER  
ON/OFF  
START  
PAUSE  
e remianed  
Tim  
(minutes)  
10  
8
9
7
5
3
1
6
4
2
PROGRAM  
RESERVE  
+
WATER  
LEVEL  
Start/Pause  
After the power is switched on, push it to  
button  
CHILD LOCK  
Start the machine  
During working, push it to pause working.  
During pause, push it to resume working.  
••••••  
button  
••••  
•••••  
button  
In normal operation mode, the reserve indicator light is off. The time  
remain indicator light is on. The digitron displays the time remained  
(in minute) before the washing is finished.  
The washing machine can detect the laundries automatically.  
After detection,it will set the water level to suitable value among  
4, 6, 8and 10 automatically.  
Push down the reserve button. The reserve indicator light is on  
the digitron displays the reserve time of finishing washing (in hour).  
When the machine is started, the reserve indicator light is on,  
indicatingthat the reserve function is running.  
You can also set water level by yourself. After the machine is  
started, it will not set water level automatically. You shall push  
the start/pause button to make new setting.  
If there's water inside the tub, the machine cannot detect the  
laundries and will display water level 6 .  
•••••  
selection button  
Applicable situation  
If wet laundries are put in, it may display water level 10 . You  
must set suitable water level by yourself.  
Following automatic programs are available for selection  
PROGRAM  
If posthaste program is selected, it will display water level 3 .  
When water level 2 is reached in water filling, it will perform  
washing while filling water.When water level 3 is reached, it  
will change to normal washing.  
Common washing  
NORMAL  
Quick and high-efficiency wash for common laundries  
Super quick wash of the laundry under 1 kg with light soil  
Washing the relatively big and thick laundriesr  
Washing the chemical fiber laundries  
Washing the cotton textiles  
QUICK  
POSTHASTE  
During operation of wash and rinse program, you can push  
down the water level button to add water. When you release  
the button, or it reaches the overflow water level, the machine  
will stop adding water.  
JEAN  
FIBRE  
COTTON  
WOOLLEN  
SILK  
Washing the woollen textiles  
The water level decided may be different from actual value  
because of the different moisture level of the laundries.  
Washing the silk textile  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
Steps of using the operation buttons and description  
of the steps  
WM6002A  
POWER  
START  
ON/OFF  
remained  
10  
8
9
7
5
3
1
Time  
(minutes)  
PAUSE  
Minutes  
WASH  
6
4
2
Minutes  
SOAK  
PROGRAM  
RESERVE  
+
RINSE  
WATER  
LEL  
SPIN  
CHILD LOCK  
Push the "POWER ON/OFF " button to switch on the power.  
Push the "PROGRAM " button to select suitable automatic program.  
POWER  
ON/OFF  
2
PROGRAM  
After switching on the power, the machine will set standard program automatically. To select other automatic  
program, push the "PROGRAM" button till the relative indicator is on. Refer to the "PROGRAM" select button  
on Page 11 for the selection.  
Page 11  
For instance: select "POSTHASTE" program for laundries with small  
quantity and light soil.  
In selecting the normal program, the machine  
will execute fuzzy program to select water  
and wash time according to the cloth and weight  
of the laundries. The full procedure is controlled  
automatically.  
FIBRE  
NORMAL  
QUICK  
POSTHASTE  
JEAN  
COTTON  
WOOLLEN  
SILK  
Push the "SOAK", "WASH", "RINSE" or "SPIN" button to select suitable procedure.  
Minutes  
Minutes  
W
ater-saving  
Minutes  
SOAK  
WASH  
RINSE  
SIN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
After switching on the power, the washing machine will set to common program including"wash, rinse,  
spin "automatically. To select other procedures, push the "SOAK", " WASH", " RINSE" or "SPIN"  
button to select the time of soak, wash and spin, and the times of rinse. After switching on the power,  
if you push one of the button among "WASH", "RINSE"and"SPIN", the digitron of the former proce-  
dures will turn off automatically. The former procedures will not run. For instance: after switching on the  
power. If you push the "spin" button first, it will execute spin singly after starting.  
Attention  
.
Even there's no water in the tub, a certain period is  
required before spin starting.  
Do not use the soak program for the woollen textiles.  
Separate the laundries that are not colorfast from  
other laundries in washing.  
The pulsator will not rotate unless the water is  
filled to selected water level.  
The soak procedure can work in cooperation with automatic programs like normal, jean, fiber and cotton.There  
is intermittent pulsator stirring during soak.  
After the machine starts operation, you can only set the program and procedure during washing, and can not  
make setting in other cases.  
Press " WATER LEVEL "button,  
select suitable water level  
WATER  
LEVEL  
After switching on the power, the washing machine will execute fuzzy program automatically to detect the cloth.  
After detection, it can set the water level automatically. To select other water level, first push the "START/PAUSE"  
button, then push the "WATER LEVEL" button to set the water level. Refer to "standard dosage of the detergent  
and water quantity"in Page 9 and "water level button"in Page 11 for selection.  
Page 9  
Page 11  
Water Level and Time Table for Each Program (self programming not included)  
PROGRAM  
Water  
level  
Wash  
(min)  
About  
10-16  
Rinse (min/time)  
Spin (min)  
Total time  
(min)  
About 19-25  
NORMAL 1-10  
Save water program, total 10 around  
QUICK  
POSTHASTE 3  
1-10  
About 5  
About 2  
Save water program, total 10 around  
Save water program, total 4 around  
About 15  
About 6  
About 54  
JEAN  
1-10  
1-10  
About 20 Rinse twice, about 5 each About 6  
time  
About 12 Rinse twice, about 3  
About 10 Rinse twice, about 3  
About 3  
About 5  
FIBRE  
About 4  
About 4  
About 3  
About 3  
About 41  
About 49  
About 24  
About 30  
COTTON 1-10  
WOOLLEN 1-10  
Rinse twice, about 2  
Rinse twice, about 2  
SILK  
1-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
* Total time: including the normal water inlet time and drain time. The total washing time may be influenced by  
the water inlet pressure and water level.  
* Spin time: From the moment the intermittent spinning starts to the moment it stops running (the time displayed  
on spin digitron is from intermittent spinning to the moment before inertia spinning; the time displayed on the  
time remain digitron is the total remaining time)  
* In soaking, after water inlet it will perform soaking for about 10-40 minutes, then perform washing, rinsing and  
spinning.  
* In selecting "pasthaste" program, the washing machine will set the complete procedures of water level  
selector, washing, rinsing and spinning automatically.  
Push the "RESERVE" button to select suitable reserve wash program  
RESERVE  
After switching on the power, the reserve program is set to off mode automatically. If you need to set the washing  
procedure to be finished at reserved time, please push the " reserve " button to set the reserve wash program.  
Refer to reserve button in Page 11 for selection  
Page  
Time remianed  
(minutes)  
Confirm the operation of reserve program  
Reserve  
When the "RESERVE " function is activated, the indicator light of the program you have  
(hours later)  
set will be off. The "reserve (hours later)" and "time remain (minutes) " indicator lights will  
be on. During reserve procedure, push the "reserve" button to display the reserve mode.  
To change the running program or cancel the reserve setting, you  
the washing will be finished after 18 hours.  
need to switch off the power and make new selection.  
START  
Push the "START/PAUSE"button  
PAUSE  
6 Finish washing  
5 Close the lid  
After Finishing wash  
alarm automatically  
As the top lid opened ,the Washer will automatically give an alarm  
and stop running , exclusively during supplying water and rinsing.  
After finishing wash it'll alarm automatically  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using process  
Disposal after washing  
After using, please clean the lint and foreign materials of the lint filter etc. in time. Otherwise it may influence  
your using the machine.  
Please first pull off the power plug from the receptacle before cleaning.  
Clean the detergent box and set it on  
the control panel seat.  
1.The method of dismantle : Push it up aslant and gently.  
2.The method of install : install it upwards and aslant  
and push it in .  
The lint filter must be used during washing.  
It must be cleaned in time after each using  
Lint filter:  
1.Rotate the inner tub with hand till the lint filter reaches  
the position convenient for you to take it off. Pull it up to  
dismantle.  
2.Push it down to install.  
3.Clean the filter screen after washing.  
Install  
Dismantle  
Dismantle  
Install  
Dismantle  
Install  
The filter screen of the water inlet valve is likely to be  
blocked by foreign materials and influence the water  
inlet.  
If the cabinet is dirty, wipe it with wet cloth  
Do not flush it directly with water.  
Wipe it with neutral detergent.  
Please clean it with brush every two months.  
Do not wipe it with thinner, petrol, alcohol etc.  
Petrol  
Thinner  
Alcohol  
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).  
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.  
3.Be sure to pull off the power plug before maintenance.  
4.Hang up the power cord and drain hose.  
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time (  
about 1 hour), then close the top lid.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Trouble-shooting Answer to question  
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns  
sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special  
maintenance department or after-sale service department of our company. Do not repair it by yourself.  
Phenomenan  
The reason  
How to settle  
Close the top lid.  
The top lid is opened during reserve  
procedure.  
The digitron displays E0.  
Put down the drain hose. Open and close the  
top lid once.  
The drainage cannot work, or is too slow.  
The digitron displays E1.  
Is the drain hose put down?  
Is the drain hose blocked?  
Clean the foreign material. Open and close  
The top Lid Once.  
It stops running in midway. The digitron  
displays E2.  
Close the top lid.  
The top lid is not closed.  
Are the laundries put slantingly?  
Is the machine slanting?  
Reorder the laundries. Close the top lid.  
The machine will start running after 10  
seconds of being placed horizontally.  
The safety switch acts, and the  
spinning cannot work. The  
digitron displays E3.  
Open the water tap. Push the start/Pause  
button once.  
Clean the water inlet valve then push  
the start/Pausebutton once.  
Is the water tap opened, or is there water  
supply failure?  
Is the water inlet valve blocked?  
Is the water pressure too low?  
The water filling does not work, or is  
slow. After about 15 minutes later,  
the digital displays E4.  
Push the Start/Pause button once.  
Please contact the after-sales  
service department.  
The water level sensor is bad.  
The digitron displays E6.  
The power voltage is too low.  
The power voltage is too high.  
The digitron displays E8.  
The digitron displays E9.  
Not wash  
Pull off the power plug. Wait for the  
voltage resuming normal before usage.  
Is there power failure?  
Is the power plug inserted tightly?  
Is the water level reached preset position?  
Please use it when there's power supply.  
Insert the power plug tightly.  
Fill water to the preset position.  
The machine does  
not act  
Insert the power plug tightly.  
Close the top lid.  
Set the laundries flat.  
Is the power plug inserted tightly?  
Is the top lid closed reliably?  
Are the laundries set flat?  
Not spin  
Is the machine slanting?  
Are the laundries put slantingly in spinning?  
Are there any foreign materials?  
Adjust the machine to be level  
Reorder the laundries and close the top lid.  
Remove the foreign materials.  
There's abnormal sound  
inside the machine  
Is the screw of the jointer of water  
inlet hose loose or awry?  
The water tap leaks  
Fasten the screw of the jointer properly.  
Common phenomena  
Phenomena  
Explanation  
* The spinning is intermittent when it starts.  
* The wash procedure pauses.  
* Balance the laundries to avoid slanting.  
* The cloth sensor is detecting the cloth. It will start  
adding water after about 48 seconds.  
* Select “ SPIN” program, but it doesn’twork.  
* The program is setting the drain time. A certain  
period is needed before it starts spinning.  
* The pusaltor pauses during washing, rinsing * It is to avoid splashing during water filling.  
or adding water.  
* There may be some water flowing out of the * It is the water remained in the performance  
drain hose in the first use of the machine.  
inspection by the factory.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Packing list  
Name  
Quantity  
One  
Storage position  
Inside the document bag  
User's manual  
Inside the document bag  
Inside the accessory bag  
One  
One  
Lint filter  
Components of the  
water inlet hose  
Between the upper cushion of the  
washing machine package and the  
upper seal of the package carton  
One  
Bottom plate  
Eight  
Tapping screws ST4x16-A  
Inner cover component  
Inside the accessory bag  
Inside the accessory bag  
One  
One  
Computerized Automatic  
washing machine  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specification  
Model  
WM6002A  
Rated voltage frequency  
Rated washing / spinning capacity  
Water level/Water quantity (about)  
Max water consumption  
Injection pressure  
220-240V~ 50Hz  
6.0kg (weight of standard dry cloth)  
1/16L 2/20L 3/24L 4/28L 5/32L  
6/38L 7/42L 8/45L 9/47L 10/50L  
About 75L(High water level; Standard program)  
0.03MPa~0.78MPa  
Rated washing power  
Rated spinning power  
Weight About  
380W  
260W  
36kg  
Dimension  
L 520 mm W 520 mm H 908 mm  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Greenheck Fan Humidifier HRE 20 User Manual
Grizzly Sander G0486 G0487 User Manual
Haier Washer XPB72 0713S User Manual
Hatco Food Warmer FST 1 MN User Manual
Healthrider Home Gym E660 User Manual
HP Hewlett Packard Cassette Player 1760 User Manual
HP Hewlett Packard Switch 12076A LAN 1000 LINK User Manual
Huey Chiao Headphones HCB08 User Manual
Husqvarna Blower 350BT BF User Manual
IBM Projector IL1210 User Manual