HLP21E MANUAL 6/20/03 10:03 AM Page 2
®
TM
Wh a t Th e Wor ld Com es Hom e To
Portable
Electronic Washer
Lave-Linge
Électronique Mobile
Lavarropas
Eléctrico portátil
User Manual-
Model #
Modèle #
Guide de l'Utilisateur-
Manual del Usuario-
HLP21E
Modelo #
Download from Www.Somanuals.com. All Manuals Search And Download.
HLP21E MANUAL 6/20/03 10:03 AM Page 4
English
21. Proper grounding must be ensured to reduce the risk of shock and fire. DO
NOT CUT OR REMOVE THE GROUNDING PLUG. If you do not have a
three-prong electric receptacle outlet in the wall, have a certified electrician
install the proper receptacle. The wall receptacle MUST be properly grounded.
22. Hydrogen gas may be produced if the water heater has not been used in more
than 2 weeks. This may be explosive under certain circumstances. If this is the
case turn on all the hot faucets and let the hot water run for a few minutes
before using this appliance. This will let the trapped hydrogen escape. Avoid
accidents during this process by refraining from turning ON any electrical
appliances, smoking, lighting a match/ lighter, and using flames.
23. Do not repair or replace any part of the appliance or attempt any servicing
unless specifically recommended in the user-repair instructions, which you
understand and have the skill to carry out.
N o te : If for any reason this product requires service, we strongly
recommend that a certified technician perform the service.
24. To reduce the risk of electric shock or fire, do not use extension cords or
adapters to connect the unit to an electrical power source.
SAVE THESE INSTRUCTIONS
For Future Use
DANGER
Risk o f ch ild e n tra p m e n t. Be fo re th ro w in g a w a y y o u r o ld
a p p lia n ce , re m o ve th e d o o r so th a t ch ild re n m a y
n o t e a sily b e co m e tra p p e d in sid e .
Thank you for purchasing our Haier
product. This easy-to-use manual will
guide you in getting the best use of
Model number
your washer.
Serial number
Remember to record the model and
serial number. They are on a label in
back of the washer.
Date of purchase
(Sta p le y o u r re ce ip t to y o u r m a n u a l.) Yo u w ill n e e d it to
o b ta in w a rra n ty se rvice .
2
Download from Www.Somanuals.com. All Manuals Search And Download.
HLP21E MANUAL 6/20/03 10:03 AM Page 5
English
Table Of Contents
PAGE
SAFETY IN STRUCTIO N S ................................................................1 -2
PARTS AN D FEATURES ..................................................................4 -5
O PERATIN G YO UR W ASHER ....................................................6 -1 1
UN PACKIN G AN D ACCESSO RIES IN VEN TO RY ..........................1 2
PRO PER LO CATIO N ........................................................................1 3
IN STALLATIO N IN STRUCTIO N S ..............................................1 4 -1 6
UN IT DIMEN SIO N S ........................................................................1 7
ELECTRICAL CO N N ECTIO N S ..........................................................1 8
PRO PER CARE AN D CLEAN IN G ....................................................1 9
TRO UBLESHO O TIN G GUIDE ....................................................2 0 -2 1
WARRAN TY......................................................................................2 2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HLP21E MANUAL 6/20/03 10:03 AM Page 6
English
OPERATING INSTRUCTIONS
Pa rts a n d Fe a tu re s
1
2
3
5
4
1. Top Lid
4. Front Leveling Leg
2. Control Panel
3. Washer Cabinet
5. Cabinet Handle (located on both
sides of the washer)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HLP21E MANUAL 6/20/03 10:03 AM Page 7
English
2
3
4
1
5
6
1. Water Inlet Valve
4. Power Cord Holder Clip
2. Water Absorption Cushion
3. Water Level Selector
5. Power Cord (115 Volt / 60 Hz)
6. Drain Hose
5
Download from Www.Somanuals.com. All Manuals Search And Download.
HLP21E MANUAL 6/20/03 10:03 AM Page 8
English
O PERATIN G YO UR W ASHER
Th e Co n tro l Pa n e l
POWER
ON/OFF
A
START
PAUSE
PROGRAM
SELECT
SPIN
QUICK
POWER
WASH
RINSE
WASH
High
Middle
Low
Add
Water level
select
3
2
1
4
Power ON/ OFF: (1)
• Press the button once to turn ON the power to the washer. Press it again to turn
the power OFF.
Start/ Pause: (2)
• Press this button once to start the wash process. Press this button once again to
pause the activity during the wash cycle. Push it again to resume the wash cycle.
Program Select: (3)
• Select your desired cycle program by pressing the "Program Select" button. There
are 7 options to select from. Press the Select button for the desired setting.
Water Level Selector: (4)
• Turn the Water Level Selector knob to select the proper water level setting. You
may select from low, medium and high water level settings depending on the
wash load.
Function Indicator Lights:
• The function display lights indicate that a selected feature is ON or that the cycle
is about to begin.
• During the wash cycle, a flashing light indicates the current wash/ rinse cycle
program.
• Rapid flashing indicates that the washer is not operating properly.
Lo a d in g th e W a sh e r
• Load each item loosely.
• Separate the white from the colored clothing. Separate heavy fabrics from light
fabrics.
• Carefully check all pockets and cuffs for small items. They can easily slide into the
tub and cause damage to the tub.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
HLP21E MANUAL 6/20/03 10:03 AM Page 9
English
• Pre-treat all stains and heavily soiled areas for best results.
• Do not overload your washer.
• Close the door properly after loading the clothes.
• When loading wet items, keep water level high enough to keep the unit in
balance and to allow clothing to float easily in the water.
Pro p e r Use o f De te rg e n t
• Fill water in the tub at the "Low" water level.
• Add the detergent.
• Load the washer.
• Select the water level.
N o te : The amount of detergent used depends on the size of the load, the water
type (hard or soft) and whether the clothes are heavily soiled or lightly
soiled. Besides the performance of the washing machine, the quality of the
detergent also affects the wash result. For best results, use low sudsing deter-
gents only. Refer to the detergent manufacturer’s recommended amount for
usage.
Pro p e r Use o f Ble a ch
Refer to the bleach manufacturer’s chart for the recommended use of liquid bleach.
Dilute the bleach and add it to the water before putting clothes into the washtub.
Wa rn in g ! Be careful not to spill undiluted bleach onto the washer cabinet or onto
clothing. It is a strong chemical that may damage your clothes and the
finish of the washer if not properly diluted.
Lin t Filte r a n d W a te r Filte r
• The Lint filter is located inside the washer drum. A small nylon bag collects lint
and residue from clothes during the wash cycle.
N o te : Do not wash your clothes without the filter in its compartment
inside the tub.
• You must clean the filter after every load for the best results. Push down the tab in
the filter to remove. Clean and slide the filter back in place.
• There is also a filter in the water inlet valve. This prevents foreign particles in the
water from entering the washer. Clean this at least once a month.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
HLP21E MANUAL 6/20/03 10:03 AM Page 10
English
Se le ctin g th e W a sh Cy cle
• Press the "Program Select" button for your desired wash cycle. Choose between 7
options.
• The total time includes the normal water inlet time and drain time. The total
washing time may be affected by the water inlet pressure and water level.
• The spin time is the time from the intermittent running to the finishing of the cycle.
• In the "Power Wash" program, the first soak is approximately 20 minutes,
pre-wash is approximately 8 minutes. Clothes are soaked again for
approximately 5 minutes. The washing, rinsing and spinning will then be
completed. The wash time includes the pre-wash time.
• In the "Quick" program select wash, rinse and spin are set automatically. No
procedure can be selected after setting.
N o te : When you turn the power ON, the machine will set the standard wash
program to the wash/ rinse/ spin position.
Pro g ra m Se le ct Wa sh Pro g ra m
Ap p lica tio n
Power On
Press Once
Press Twice
Press Three Times
Press Four Times
Press Five Times
Wash, Rinse & Spin
Wash
Wash & Rinse
Rinse & Spin
Normal Wash
No Spin or Rinse
No Spin
No Wash
Spin
No Wash or Rinse
For heavily soiled and
very dirty clothes
For a quick speed wash
Power Wash, Wash, Rinse,
Spin
Quick, Wash, Rinse, Spin
Press Six Times
8
Download from Www.Somanuals.com. All Manuals Search And Download.
HLP21E MANUAL 6/20/03 10:03 AM Page 11
English
Se le ctin g th e W a te r Le ve l
• There are 3 water levels to chose from: Low, Medium and High. Your selection may
depend on your wash load.
• Turning the knob to "Reset" will add more water to your wash load. Release and set
to desired level after adding water.
Re co m m e n d e d W a te r Le ve ls
N o te : Incoming hot water must not exceed 122˚F/ 50˚C.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
HLP21E MANUAL 6/20/03 10:03 AM Page 12
English
En d -o f-Cy cle Sig n a l
The machine will beep at the end of the cycle, indicating that the washing is
complete. The "Wash/ Rinse/ Spin" indicator lights will still be ON. The washer will
turn OFF automatically in approximately 10 minutes after the completion of the
cycle.
Clo sin g th e To p Lid
For safety purposes, the top lid must always be closed during the wash process. If
you open the top lid while the wash cycle is in progress, you will observe the
following:
• An alarm will sound.
• The tub will not spin while the lid is open.
• If the unit is in wash mode, it will stop running.
Simply close the top lid and press the start/ pause button to resume the cycle.
Ste p s fo r th e W a sh Pro ce ss
1. Turn the power ON by pressing the "ON" button.
2. Press "Program Select" to select the wash program. Refer to page 8 for the
selection chart.
3. Select the water level.
4. Add the detergent.
5. Add the wash load.
6. After the washing machine starts, you may change the program by turning OFF
the machine and then restarting to make the new selection.
N o te : If the washer is turned ON without any water in the tub, it will start to spin
after a few minutes. The pulsator will not rotate unless the water is filled to a
selected level.
N o te : Do not use the "Power Wash" program for woolen clothing.
1 0
Download from Www.Somanuals.com. All Manuals Search And Download.
HLP21E MANUAL 6/20/03 10:03 AM Page 13
English
N o rm a l O p e ra tin g So u n d s
The following sounds are normally heard during the operation of the washer:
• Tumbling sounds can be heard as heavy wet clothes in the washer are tossed
around continuously.
• Air rushing noise is the result of the washtub spinning at a very high RPM.
• Clicking sounds are caused by the wash and rinse cycles turning ON and OFF.
1 1
Download from Www.Somanuals.com. All Manuals Search And Download.
HLP21E MANUAL 6/20/03 10:03 AM Page 14
English
Un p a ck in g a n d Acce sso rie s In ve n to ry
Un p a ck in g
1. Remove all packing materials. This includes the foam base and all adhesive tape
holding the washer accessories inside and outside. Slide out and remove the
bottom Styrofoam that is used to protect the washer from shipping damage due
to vibrations and shock.
2. Inspect and remove any remaining packing, tape or printed materials before
using the washer.
N o te : Th e b o tto m p a n e l is lo ca te d b e tw e e n th e u p p e r fo a m p ro te c-
tio n a n d b o x .
Acce sso rie s
a) 1 Bottom Panel
b) 8 Screws for the Bottom Plate
c) 1 Water Inlet Hose
d) 1 Drain Hook (Gooseneck)
e) 1 Quick Sink Faucet Adapter
f) 2 Washers
g) 1 Lint Filter
b
c
a
d
f
g
e
Check to make sure that the accessories are present and in good condition.
If you find that they are not in good condition or are missing, please contact
our customer service department for assistance. O u r To ll-Fre e n u m b e r is
1 -8 7 7 -3 3 7 -3 6 3 9 .
1 2
Download from Www.Somanuals.com. All Manuals Search And Download.
HLP21E MANUAL 6/20/03 10:03 AM Page 15
English
Pro p e r Lo ca tio n
Ge n e ra l
• Select a suitable location for the washer on a hard even surface away from direct
sunlight and heat sources (e.g., radiators, baseboard heaters, cooking appliances,
etc.).
• Any floor unevenness should be corrected with the leveling leg located on the
bottom right corner of the washer.
• The washer must be placed at room temperature. You must not place the washer
where the temperature is at or below freezing.
Sto ra g e in Co ld En viro n m e n ts
• This appliance must be stored at room temperature.
• If you received this appliance when the outside temperature is below freezing, do
not operate until this appliance has warmed to room temperature.
• Do not install or operate this appliance in an area where room temperature is
below freezing.
1 3
Download from Www.Somanuals.com. All Manuals Search And Download.
HLP21E MANUAL 6/20/03 10:03 AM Page 16
English
In sta lla tio n In stru ctio n s
Read carefully and understand all installation instructions before installing this
washing machine. If after completing the process you are still unsure whether the
washer has been properly installed, we recommend that you contact a qualified
installer.
To o ls a n d Ma te ria ls Re q u ire d
You will need to use the following tools when installing your washer:
Scissors
Phillips Screwdriver
Flathead Screwdriver
Pliers
Wrench
Tape Measure
Gloves
Level
In sta llin g th e Bo tto m Pa n e l
The bottom panel blocks noises to provide you with the quietest performance
possible during the wash cycle operation.
1. First, lay down the washer on its front side.
2. Place the panel against the bottom of the machine. Align the holes in the panel
with the holes in the washer.
3. Insert the screws through the holes of the panel into the bottom of the washer and
tighten. (8 screws are supplied)
4. Once all screws have been installed and the panel is in place, return the washer
to its standing position.
N o te : During this time, you may reroute the drain hose to the left or right
side for draining.
1 4
Download from Www.Somanuals.com. All Manuals Search And Download.
HLP21E MANUAL 6/20/03 10:03 AM Page 17
English
In sta llin g th e Lin t Filte r
The lint filter must be installed before the washer is used.
The lint filter is packaged with the User Manual.
Le ve lin g th e W a sh e r
Your washer has an adjustable leveling leg that is located on the front right corner.
After properly placing your washer in its final location, you may level the washer.
• Loosen the adjustable nut. The leveling leg can be
adjusted by turning it counter-clockwise to raise the
washer and clockwise to lower the washer.
N o te : If the washer is inclined more than 2˚, the machine
will not operate.
In sta llin g Yo u r W a sh e r
Read the installation instructions carefully before beginning.
1. Connect the water inlet hose to the water faucet.
N o te : The ends of the inlet hose are marked red and yellow. Red goes to washing
machine and yellow goes to the faucet.
2. Connect the other ends to the washer inlet located at the top rear of the machine.
Insert a new flat washer (provided) to each end of the inlet hose.
3. The drain hose must be placed into a drainpipe or sink at least 1-1/ 2 inches in
diameter. Use the gooseneck drain hook to hold the hose in place. To avoid
possible water back-up, the drain hose must reach a height of at least 31-1/ 2
inches minimum and 40 inches maximum.
4. Plug in the washer to a regular 115 Volt / 60 Hz, 15 Amps outlet.
N o te : Carefully inspect for any leaks around the machine and at the back. If there
is a leak, check if any connections are loose. You may need to tighten any
loose connections. Do not remove the water absorption cushion. Check
before each use to make sure it is not damaged.
CAUTIO N ! If after completing these steps you are still unsure whether unit has
been properly installed, contact a qualified installer. We recommend
that the washer be installed by a certified technician to ensure that it is
properly installed.
1 5
Download from Www.Somanuals.com. All Manuals Search And Download.
HLP21E MANUAL 6/20/03 10:03 AM Page 18
English
In sta llin g Q u ick Sin k Ad a p te r:
When installing the quick sink faucet adapter to the faucet, follow the steps below:
1. First, remove the aerator from your faucet nozzle and determine the size/ type of
the faucet.
2. Once you determine the size/ type of the faucet (Outside Threaded End or Inside
Threaded End), place the proper sized rubber washer into the silver faucet
adapter.
3. Attach the silver faucet connector to the faucet.
4. Attach the faucet connector to the water inlet hose and make sure that the
rubber washer is placed in between.
5. Attach the other end of the water inlet hose to the washer water inlet and make
sure that the rubber washer is placed in between.
Faucet
Washers
Faucet Adapter
Quick Connector
Washer
Drain hose
Water inlet hose
Washer
Rear View of Washer
1 6
Download from Www.Somanuals.com. All Manuals Search And Download.
HLP21E MANUAL 6/20/03 10:03 AM Page 19
English
Un it Dim e n sio n s
17-1/4”
17-1/4”
38-5/8”
29-15/16”
17-5/8”
17-5/8”
1 7
Download from Www.Somanuals.com. All Manuals Search And Download.
HLP21E MANUAL 6/20/03 10:03 AM Page 20
English
Electrical Connections
Gro u n d in g In stru ctio n s
This appliance must be grounded. In the event of an electrical short circuit,
grounding reduces the risk of electric shock by providing an escape wire for
the electrical current. This appliance is equipped with a cord having a grounding
wire with a grounded plug. The plug must be inserted into an outlet that is
properly installed and grounded.
• Improper use of the plug can result in a risk of electric shock.
• Consult a qualified electrician or service person if the grounding
instructions are not completely understood or if in doubt as to
whether the appliance is properly grounded.
W irin g Re q u ire m e n ts
• This appliance must be plugged into at least a 15 AMP 110-115 VOLT,
60 HZ GROUNDED OUTLET.
N o te : Where a standard two-prong outlet is
encountered, it is the personal
responsibility and obligation of the
consumer to have it replaced with a
properly grounded three-prong outlet.
X
Ex te n sio n Co rd s:
We do not recommend that you use an extension cord.
Po w e r In te r ru p tio n s
Occasionally, there may be power interruptions due to thunderstorms or other
causes. Remove the power cord from the AC outlet when a power outage occurs.
When power has been restored, re-plug the power cord to AC outlet. If the outage
lasts for a prolonged period of time, clean the washer before using it again.
1 8
Download from Www.Somanuals.com. All Manuals Search And Download.
HLP21E MANUAL 6/20/03 10:03 AM Page 21
English
Proper Care and Cleaning
Wa rn in g ! Always unplug your appliance before cleaning to avoid electric shock.
Ignoring this warning may result in personal injury or death. Before
using cleaning products, always read and follow the cleaning product
manufacturer’s instructions and warnings to avoid personal injury and
product damage.
Ge n e ra l Cle a n in g a n d Ma in te n a n ce
Use only a damp or sudsy cloth to clean the control panel.
• To avoid any kind of damage to the cabinet finish, wipe the appliance cabinet as
needed. If liquid/ powdered softener, bleach or detergent is spilled onto the
cabinet, wipe the cabinet immediately because it may cause damage to the finish.
• Do not use any abrasives, harsh chemicals, ammonia, chlorine bleach,
concentrated detergent, solvents or metal scouring pads. Some of these chemicals
and materials may dissolve, damage and/ or discolor your appliance.
• Remove pins and other sharp objects from clothing to prevent scratches on interior
parts.
• The lint filter must be cleaned before each use for optimal efficiency. DO NOT
USE YOUR WASHER WITHOUT THE LINT FILTER IN PLACE.
• The filter screen of the water inlet valve may become blocked by soil and residue.
Please clean it with a brush monthly.
Lo n g Ab se n ce s / Mo vin g
• Turn OFF the water supply faucets and disconnect the hoses. Drain water from all
hoses. This will prevent damage from water leakage if the hoses are
accidentally ruptured or if they become loose.
• Disconnect the electrical plug.
• Dry the inner washtub. If moving the washer, disconnect the drain hose.
• To prevent mold and mildew, leave the door open so that the moisture inside the
machine can evaporate.
• Reinstall the foam base/ Styrofoam at the bottom of the unit to prevent internal
parts from becoming damaged due to vibrations and shock when the washer is
being moved to another location.
1 9
Download from Www.Somanuals.com. All Manuals Search And Download.
HLP21E MANUAL 6/20/03 10:03 AM Page 22
English
Troubleshooting Guide
Before calling for service, determine the symptoms and follow the suggested
solutions:
Wa sh e r d o e s n o t o p e ra te :
• Check if the unit is plugged in. The plug may have come loose.
• Check if the electrical wall receptacle is of proper voltage.
• Check if the circuit breaker needs to be reset or if the fuse needs to be replaced.
• Check if the washer is overloaded. Reload and redistribute the clothing to
rebalance the machine.
• Check if the door is open. You may have to close the door properly.
• Check if the program selections are set properly. You may have to adjust the
settings.
• Check the Power "ON/ OFF" button to see if it is in the OFF position. You may
need to press the button to set it in the ON position.
• Check if the "Start/ Pause" button is on "Pause" mode. Press this button to start the
wash process.
• The wash process is paused. This is normal. The clothing sensor is checking to
verify that there are clothes inside the washtub. Water will be added
approximately 48 seconds later.
• The pulsator pauses during incoming water flow in the wash and rinse cycle. This
is normal. This prevents splashing during water inlet.
• The washer may need to be reloaded and the clothes may need to be rebalanced.
Pro b le m s w ith w a te r:
• Not enough water is coming in - The water faucet may need to be fully turned
ON. Water hose may be tangled or bent. Straighten the hose. Check the water
level selection. It may need to be readjusted. This may cause the wash program to
pause for a few minutes after water inlet.
• Water leaks - This is due to improper installation of the drain hose or fill hose.
Your home drain may be clogged. You may need to tighten the hose, check the
plumbing or call a plumber. Water may also leak if the machine is overloaded or
if too much detergent is used.
• Water does not drain - This is due to improper installation of the drain hose. You
may need to connect the drain hose properly. Check the position of the drain
hose. The drain hose may be clogged or bent.
• Water flows out of the drain hose during the first use of the machine - This may
be the water left in the tub after the factory inspected the unit to test its
performance in order to ensure the best quality.
2 0
Download from Www.Somanuals.com. All Manuals Search And Download.
HLP21E MANUAL 6/20/03 10:03 AM Page 23
English
Wa sh e r m a k e s n o ise s:
• Washer may need to be reinstalled and leveled. Refer to the washer installation
section.
• Wash load may need to be rebalanced, as the load may be uneven.
• Coins, loose change, buttons or other heavy objects may be making the noise.
Refer to the Operating Guide – Normal Operating Sounds.
• A squeaking sound may be due to an overloaded washtub.
• Vibration noises are due to an improper leveling of the washer or an uneven
distribution of clothing in the tub.
Pro b le m s w ith clo th in g :
• Clothes are too wrinkled – Clothes have been improperly sorted or the machine
has been overloaded. Do not mix heavy clothes such as work clothes with light
clothes such as blouses, light shirts and delicate items.
• Clothes have soap residue – The detergent may not be dissolving in the water.
Check the water temperature or add detergent as the washtub is being filled with
water (before you load your clothes) to avoid soap residue on clothes. Liquid
detergent is recommended.
• Clothes are ripped or have holes - Sharp objects such as pins and belt buckles
were left in the washtub. You must remove small, loose, sharp objects. Fasten
belts, zippers, metal snaps etc. Check if you are using undiluted bleach. Never
add undiluted bleach to the wash.
O th e r:
• The spinning is intermittent when it starts – The laundry needs to be balanced to
avoid slanting.
• The "Spin" does not work in Program Select – The program is setting the drain
time. Spinning will start in a few minutes.
• During the final spinning, it stops, the "Rinse" indicator lights up and the washer
starts to fill with water – The wash load is slanting on one side. After the water is
filled, the slanting will be removed and the spinning will be reactivated.
2 1
Download from Www.Somanuals.com. All Manuals Search And Download.
HLP21E MANUAL 6/20/03 10:03 AM Page 24
English
Limited Warranty
In Ho m e Se rvice
Th is w a rra n ty co ve rs a p p lia n ce s
w ith in th e co n tin e n ta l Un ite d Sta te s,
Pu e rto Rico a n d Ca n a d a . W h a t is
n o t co ve re d b y th is w a rra n ty :
Replacement or repair of household fuses,
circuit breakers, wiring or plumbing.
A product whose original serial number has
been removed or altered.
Fu ll O N E Ye a r W a rra n ty
For 12 months from the date of original retail
purchase, Haier will repair or replace any
part free of charge including labor that fails
due to a defect in materials or workmanship.
Lim ite d W a rra n ty
Any service charges not specifically identified
as normal such as normal service area or
hours.
After one year from the original retail
purchase date, Haier will provide a part at
no cost, as indicated below, to replace said
part as a result of a defect in materials or
workmanship. Haier is solely responsible for
the cost of the part. All other costs such as
labor, trip charge, etc are the responsibility of
the owner.
Damage to clothing.
Damage incurred in shipping.
Damage caused by improper installation or
maintenance.
Damage from misuse, abuse accident, fire,
flood, or acts of nature.
Damage from service other than an
authorized Haier dealer or service center.
Damage from incorrect electrical current,
voltage or supply.
Damage resulting from any product
modification, alteration or adjustment not
authorized by Haier.
Adjustment of consumer operated controls as
identified in the owner’s manual.
Hoses, knobs, lint trays and all attachments,
accessories and disposable parts.
Labor, service transportation, and shipping
charges for the removal and replacement of
defective parts beyond the initial 12-month
period.
Se co n d th ro u g h Fifth Ye a r
Haier will provide the outer washtub and
related outer tub assembly parts should the
part fail to hold water.
Se co n d th ro u g h Se ve n th Ye a r
Haier will provide the inner stainless steel
wash tub if defective in material or workman-
ship.
N o te : This warranty commences on the
date the item was purchased and the original
purchase receipt must be presented to the
authorized service representative before
warranty repairs are rendered.
Damage from other than normal household
use.
Any transportation and shipping charges.
Ex ce p tio n s: Commercial or Rental Use
Warranty
9 0 d a y s la b o r fro m d a te o f o rig in a l
p u rch a se
THIS LIMITED W ARRAN TY IS GIVEN
IN LIEU O F ALL O THER W ARRAN TIES,
EXPRESSED O R, IN CLUDIN G THE
WARRAN TIES O F MERCHAN TABILITY
AN D FITN ESS FO R A PARTICULAR
PURPO SE
9 0 d a y s p a rts fro m d a te o f o rig in a l
p u rch a se
N o o th e r w a rra n ty a p p lie s
Fo r W a rra n ty Se rvice
The remedy provided in this warranty is
exclusive and is granted in lieu of all other
remedies.
Contact your nearest authorized service cen-
ter. All service must be performed by a Haier
authorized service center. For the name and
telephone number of the nearest authorized
service center please call 1-877-337-3639.
This warranty does not cover incidental or
consequential damages, so the above
limitations may not apply to you. Some states
do not allow limitations on how long an
implied warranty lasts, so the above
limitations may not apply to you.
Be fo re ca llin g p le a se h a ve a va ila b le
th e fo llo w in g in fo rm a tio n :
Model number and serial number of your
appliance. The name and address of the
dealer you purchased the unit from and the
date of purchase.
This warranty gives you specific legal rights,
and you may have other rights, which vary,
from state to state.
A clear description of the problem.
A proof of purchase (sales receipt).
Haier America
New York, NY 10018
2 2
Download from Www.Somanuals.com. All Manuals Search And Download.
HLP21E MANUAL 6/20/03 10:03 AM Page 1
IMPO RTAN T
Do N o t Re tu rn Th is Pro d u ct To Th e Sto re
If y o u h a ve a p ro b le m w ith th is p ro d u ct, p le a se co n ta ct th e "Ha ie r Cu sto m e r
Sa tisfa ctio n Ce n te r" a t 1 -8 7 7 -3 3 7 -3 6 3 9 .
DATED PRO O F O F PURCHASE, MO DEL # AN D SERIAL # REQ UIRED FO R W ARRAN TY SER-
VICE
IMPO RTAN T
N e p a s re n vo y e r ce t a p p a re il a u m a g a sin .
Si vo u s a ve z u n p ro b lè m e a ve c ce t a p p a re il, ve u ille z co n ta cte r le se rvice à la clie n tè le
d e Ha ie r a u 1 -8 7 7 -3 3 7 -3 6 3 9 .
IL EST O BLIGATO IRE DE FO URN IR UN E PREUVE D'ACHAT DATÉE, LE N UMÉRO DU MO DÈLE
ET SO N N UMÉRO DE SÉRIE AFIN DE BÉN ÉFICIER DE LA CO UVERTURE DE LA GARAN TIE.
IMPO RTAN TE
N o De vu e lva Este Pro d u cto a l Esta b le cim ie n to Co m p ra .
Si tie n e p ro b le m a s co n e ste p ro d u cto , p o r fa vo r p ó n g a se e n co n ta cto co n e l "Ce n tro
Ha ie r d e Ate n ció n a l Clie n te " e n e l 1 -8 7 7 -3 3 7 -3 6 3 9 .
PARA EL SERVICIO DE GARAN TÍA SE REQ UIERE PRUEBA DE CO MPRA, FECHADA, N o . DE
MO DELO Y N o . DE SERIE
1 1 5 V, 6 0 Hz
Ma d e in Ch in a
Fa b riq u é e n Ch in e
He ch o e n Ch in a
®
TM
Wh a t Th e Wor ld Com es Hom e To
Ha ie r Am e rica
N e w Yo rk , N Y 1 0 0 1 8
Prin te d in Ch in a
HLP21E-01
Issued: May-03
Part # WD-9999-14
Download from Www.Somanuals.com. All Manuals Search And Download.
|