Twin-tub Washing Machine
User's manual
This manual is for
HWM55-23BS
Please read this manual
carefully before using.
Retain it foDr ofuwtnuloraedrfreofmerWewnwce.S.omanuals.com. All Manuals Search And Download.
Names of the parts
Spin timer
Outer cover of the spin tub
Inner cover of the spin tub
Wash water-filling entrance
Wash selector
Wash timer
Spin tub frame
Spin tub
Control panel
Overflow filter
Cabinet
Water level adjusting lever
Drain hose
Lint filter
(Installed by user)
Pulsator
Wash tub
Base frame
Meaning and description of the symbols
Contents marked with that symbol are related
to the safety of the product and the personal
safety of the users. Please operate in strict
conformity to the contents, otherwise it may
cause damage of the machine or injure the
personal safety of the user.
Warning sign
Contents marked with that symbol are actions
forbidden to perform. Performing of those
actions may result in damage of the machine
or injure the personal safety of the user.
Forbidding sign
Please check if the power receptacle has good earthing
condition before using to guarantee your safety.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Safety precautions
When the machine is normally
Please insert the power cord into
special receptacle with rated vol-
tage. Be sure to use single-phase
three pins receptacle. The earthing
terminal of the receptacle must be
earthed reliably. If possible, please
adopt electric leakage protector.
using, please put the power plug
at the location easily to be insert-
ed and extracted by hand. Be sure
to pull the plug off when there's
power failure, or the machine is
being moved, cleaned or when it
is idle.
If the power cord is bad, to avoid risk it is required to replace it by the
technicians of our special shop or the after-sale service department.
Keep the pin of the power plug clean.
Do not put the machine at damp
place like the bathroom . Never
wash it with water. Do not place
wet laundries on the control panel.
Do not use water hotter than 50 C .
In case the washing machine is installed
on ground with carpet , do not block the
ventilation hole with carpet.
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Ventilation hole at
the bottom of the
washing machine
Do not let the machine share one receptacle
with other electric appliances. If the power
plug is damaged, or the plugging into the
receptacle is loose, do not use the plug any
more.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Safety precautions
Do not stretch hands into the working
machine. It is dangerous even if the
rotation is slow. Take special care of
the children.
Do not decompose, repair or alter the
machine by yourself.
Do not put any hot or heavy items
( such as the kettle with hot water )
on the washing machine.
Do not wash laundries with volatile
materials (such as thinner, petrol etc.).
etrol
P
er
inn
Th
Keep the machine away from direct
sunlight and heat source like the
heater.
Handicapped or children without care
shall not use the machine.
To protect your laundries and wash-
ing machine, please take out all of the
coins, buttons, sand, hairpin and
other foreign materials before washing.
Please check if the water faucet is open,
and if the connection of the water inlet
pipe is proper.
It is suggested to use foamless washing
powder.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Installation and adjustment
Please install and adjust the machine according to the requirement of
the manual. It is very important to your security and correct operating
the machine.
Install the lint filter
After opening the package, please take out the lint
filter from the document bag, install it to the overflow
filter of the wash tub. See to the figure.
Overflow filter
Lint filter
Usage of the drain hose
The drainage shall be smooth with the drain hose.
1.The height of the drain hose shall be
less than 10cm , or the drainage will
not be smooth enough and cause
<10cm
incomplete drainage.
2.Do not tramp or press the drain hose.
3.If the drain hose is too long, cut it at mid point.
To make smooth drainage, cut the front end of
the hose slantingly.
4.If extra drain hose is needed , please make
separate purchase. The inner diameter of the
extra hose shall not less than 30mm, and the
>
30mm
length shall not exceed 1.5m.
<1.5m
If the extra hose is too long, cut it either
at point A or B.
A
B
4
Download from Www.Somanuals.com. All Manuals Search And Download.
How to change the direction of the drain hoses
Back
Front
Figure 1 indicates the ex factory installation
position of the drain hose.
Soft item
Extend the drain hose from the side of wash tub
Figure 1
Put soft items on the ground. Lean the machine
down gently with the front surface facing the
ground. Take off the drain hose from the cabinet.
Take the hose out of the fixing groove.
(See to Figure 2).
Soft item
Figure 2
Embed the drain hose into the groove along the side
of thewash tub in the order of (1)~(2), heading for the
side of the wash tub. (See to Figure 3).
Embed the drain hose into the groove with
hands. Take care not to damage the drain
hose in fastening the fixing clamp.
Extend to the
wash tub side
Figure 3
Embed into the
groove in turn
Extend the drain hose from the rear side
Take out the drain hose from the fixing groove. Extend it from
the rear side as per the direction of the arrow. (When the drain
hose is extended from the rear side, it can be hung on the
point for drain hose at the two sides of the cabinet.)
(See to Figure 4).
Figure 4
Install the water inlet hose; Select the water level
Insert the water inlet hose into the water-filling
entrance on the control panel directly. (pull it
out to dismantle it)
Water inlet hose
Wash water-filling
entrance
Water level
indicator
Select water level according to the
quantity of the laundries.
Adjust the water level adjusting
lever to desired water level line.
Max
Med
Min
Maximum
Medium
Minimum
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Preparation before washing
Preparation before washing
1.Connect the water inlet hose.
2.Confirm that the washing machine is earthed
reliably . Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.
3.Put down the drain hose .
4.Slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally.
Pay attention to followings before washing the laundries
Check if
The quantity of
When the pulsator
Clear the
Tie the long
strips; fasten
the buttons;
close zippers.
the laundries
has special
requirement
on washing
the laundries is running , the
shall not be too buttons of the
large. Stretch laundries may
and loosen the cause noise. For
laundries before the sake of
pocket. Take
out the coins,
sand, hairpins
etc.
putting them in discretion, please
the tub.
put the laundries
with buttons into
other laundries.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like
mud or dust. For the parts with heavy soil, please apply detergent on
them in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn
it over before putting in.
f. Do not put those laundries polluted by chemicals into the washing
machine directly.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
The musts in washing
The capacity of washing and spinning of the
machine refer to the largest weight of the
standard laundries under dry condition that can
be washed or spinned in one time. Laundries
quantity in one washing cycle shall be lower
than the rated capacity.
The thickness ,size , type of the cloth will influ-
ence the actual washing capacity. It is suit-
able to put in reasonable amount of laundries
and the laundries can be turned round in wash-
ing for one time washing.
Do not select " Maximum " water level for
laundries less than 2.4kg, so as to avoid
splashing of water.
It is suggested not to use high sudsing detergent.
Usage of the detergent
How to use the whitener
How to use the washing powder
Direct dissolved in the machine:
1.Fill small quantity of water.
2.Add the powder . Run for 30
seconds to dissolve it completely.
3.Put it in the laundries. Select suitable
water level.
Fill water to decided level. Dilute
the whitener with container.
Pour it slowly into the washing tub.
Avoid using whitener on laun-
dries with color or pattern as they
are prone to lose color.
The instant dissolving of the washing
powder:
1.Prepare warm water of 30 C and a
container.
2.Add the powder while stirring to fully
dissolve it.
The powder is more prone to pollute the
laundries than the detergent. Therefore
please use it with proper quantity.
The whitener shall not touch
the laundries directly.
Refer to the user's manual for
the usage and quantity of the
whitener.
For powder whitener, please
dissolve it before using.
Dosage of different washing powder is
different. Please refer to the instruction
of the washing powder for the detail
dosage.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Washing sequence
Water-filling entrance
Spin timer
Wash timer
Wash selector
(Soft current,
strong current)
(to set to below 1 minute,
first set to 2 minute then
turn it back. it can increase
the service life of the timer).
(To set to below 2 minute,
first set to minute then
turn it back. it can increase
the service life of the timer).
5
WASH SELECTOR
WASH TIMER
SPIN TIMER
OFF
SILK
OFF
STRONG
SILK
WOOL
WOOL
SOFT
DRAIN
COTTON
LINEN
Wash
Topmost water level
1. Select water level
Max
Maximum
Set the water level adjusting lever to needed line.
Please do not over the topmost water level
(Figure 1)
Med
Medium
Min
Minimum
Figure 1
Figure 2
2. Fill the water and add the dissolved washing
powder to make the water level reach the preset
position. (Figure 2)
Run washing program for some time to stir and
dissolve the powder completely.
WASH SELECTOR
STRONG
SOFT
DRAIN
3.Put in the laundries. If the water quantity is
insufficient, please add water.
Figure 3
Figure 4
WASH TIMER
OFF
SILK
WOOL
4.Select the current.
Select the strength of the current according to
the laundries. (Figure 3)
COTTON
LINEN
5.Select the washing time
Select the washing time according to the laundries.
(Figure 4)
WASH SELECTOR
STRONG
SOFT
DRAIN
Figure 5
6.After washing, the buzzer will ring. Set the "WASH
SELECTOR" at "DRAIN". (Figure 5).
Note:
Please do not inlet over the topmost water level
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Spinning
1.Put the laundries into the spin tub evenly and smoothly.
2.Spin
(1) Put the gland in properly.
Please put in the gland properly even if the laundries quantity is small.
Push
Gland
Push
Proper
Proper
The laundries
are slanting
(2) Close the inner and outer cover of the spin tub.
No gland
Outer cover of
The spin tub
Inner cover of
The spin tub
(3). Spin
Select suitable spin time according to the laundries, and do spinning.
During spinning, if there's abnormal sound, it is generally owing to
slanting placement of the laundries. Please stop the machine
and re-order the laundries.
In spinning, it will pause the work if you open the outer cover of the spin
tub. Close it to resume the spinning.
To do spinning and draining in together, please
first do spinning for around 1 minute, then
do draining . Otherwise the spinning will stop
owing to too much water stored in the spin
tub.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Disposal after washing
After using, please clean the lint and foreign materials of the lint filter and
overflow filter in time. Otherwise it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
Cleaning the lint filter
The lint filter must be used during washing.
It must be cleaned in time after each using.
1. Take off the lint filter
Put hand at the indicated position.
Push down to take it off. ( See to
Figure 1)
Figure 1
2. Clean the lint
Put it in water and clean while it is
still wet.(See to Figure 2)
3. Install the lint filter
After cleaning, insert the bottom
of the lint filter ( marked with
"down side") into the overflow filter ,
then push the upper part of the
filter in ( marked with " up side ").
(See to Figure 3)
Figure 2
Figure 3
Cleaning the overflow filter
Too much lint on the overflow filter will influence
the normal usage of the machine. Please
clean it every two months.
Elastic fixing
claw
As indicated in the figure, nip the elastic fixing
claw and pull it to the direction of the arrow to
take it off.
1
Take off the overflow filter.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Cleaning the overflow filter
2. Take off the corrugation pipe.
Dismantle the upper part of the
corrugation pipe inside the
overflow filter ( as indicated in
Figure 1).
Water level
adjusting lever
Corrugation
Pipe
3. Cleaning the overflow filter
Clean the lint around the filter
and flush with tap water.
Figure 1
4. Install the overflow filter.
(1).Install the corrugation pipe.
(2).Insert the mounting plate at
the bottom of the filter into
the valve cover.
Hook
(3).Hang up the hook at the left
upper side.
(4).Push the upper part in as
indicated in Figure 2.
Figure 2
Disposal of the complete unit
After washing, dismount the water inlet
hose.
Do not store water in the tub for long
period. Discharge the water immediately
after each using.
Pull off the power plug and hang up the
power cord.
Hang up the drain hose.
Wipe the complete unit with soft
cloth twisted dry.
Wipe with neutral detergent if too dirty
Do not wash it directly by water
Wipe off the water drops on the surface
and inside the tub with clean soft cloth.
Open the cover of the wash tub and the
inner/outer cover of the spin tub for
some time (about one hour), then close
them.
Petrol
Thinner
Alcohol
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Trouble-shooting Answer to question
If the laundries fall to the outer side of the spin tub
If the laundries fall to the outer side of the spin tub,
please take them out immediately.
1.Dismantle
As indicated in the figure, push the point marked
Spin tub frame
with " " to pull the spin tub frame to oblique
upwards to dismantle it.
2.Install
After install the back edge of the spin tub frame to
proper position, push the four points marked with
"
" by force to reset it.
Please check carefully. The laundries may fall to
the lower part of the outer side of the spin tub
(as indicated in the figure).
If the laundries fall to the outer side of the spin
tub, during spinning the draining will get blocked
and the rotation speed of the spin tub is reduced.
Laundries
When the remained water is frozen
Prevent the freezing (be sure to discharge the water completely after using)
After complete draining, set the "WASH SELECTOR" at "STRONG" or "SOFT".
If it is set at "DRAIN", it will be rather difficult for the frozen water to melt.
Below 50
2~3L
When the water is frozen
Pour hot water below 50
into the wash tub
to soak it completely. Then turn the pulsator
with hands gently. Please confirm the drainage
can work normally before next using.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble-shooting Answer to question
If there's breakdown, please pull off the power plug before checking) The following
phenomena are not breakdowns sometimes. Please confirm again before sending it
to repair. If there are real breakdowns, please come to the special maintenance
department or after-sale service department of our company. Do not repair it by yourself.
Phenomena
The reason
Is there power failure?
Is the power plug loose?
Is the pulsator twisted by foreign materials?
The machine does
not act.
Is the drain hose put down?
Is the drain hose frozen?
Is the drain hose blocked by foreign material?
Are there laundries falling to the outer side of
the spin tub?
The draining does
not work
There's abnormal sound
during washing
Are there hair pin, coins or metal items brought
inside the tub?
There's abnormal sound
and violent vibration
during spinning
Is the machine slanting?
Is the gland pressed evenly?
Are there laundries falling to the outer side of
the spin tub?
Are the laundries in spin tub too much?
There may be some water
flowing out of the drain
hose in the first use of
the machine.
It is the water remained in the factory inspection
of performance.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Packing list
Quantity
One piece
Name
User's manual
One piece
One piece
Water inlet hose
Lint filter
One piece
One set
Gland
Twin-tub washing machine
Specification
Maximum/39L Medium/30L Minimum/24L
Water level/Water quantity (about)
Injection pressure(MPa)
0.02 0.2
5.5/4.5
Rated washing capacity(kg)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
|