Trouble-shooting
SEMI AUTO WASHING MACHINE
AWT-80LI
If the laundries fall to the outer side of the spin tub
If the laundries fall to the outer side of the spin tub,
Please contact the after-sales service department.
(If there's breakdown, please pull off the power plug before checking) The following
phenomena are not breakdowns sometimes. Please confirm again before sending
it to repair. If there are real breakdowns, please come to the special maintenance
department or after-sale service department of our company. Do not repair it by yourself.
How to settle
The reason
Phenomena
Manual
Is there power failure?
Is the power plug loose?
Is the pulsator twisted by
foreign materials?
Use it when the power is on.
Insert the power plug tightly.
Remove the foreign materials?
USER
WASHING MACHINE
The machine does
not function.
CONTENTS
Has the drain hose being
laid down?
Put down the drain hose?
Remove the foreign material?
The draining does
not function
Is the drain hose blocked
by foreign material?
Are there any laundries
trapped at the outer side
of the spin tub?
Packing list
Specification
Please contact the after-sales
service department.
Names of the parts
Safety precautions
Installation and adjustment
Preparation before washing
Do s and don ts
Are there hair pin, coins
or meta items brought
inside the tub?
Remove the hair pin, coins or
metal items
There's abnormal
sound during
washing
Usage of the detergent
Washing sequence
Maintenance
Pressed the gland evenly
Is the machine slanting?
Is the gland pressed evenly?
Are there any laundries trapped
at the outer side of the spin tub?
Are the laundries in spin tub over
loaded?
There's abnormal
sound and violent
vibration during
spinning
Level the machine properly.
Remove the laundries
Remove a little laundries
Trouble-Shooting
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Names of the parts
After using, please clean the lint and eyewinker of the lint filter and
overflow filter in time. Otherwise it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
Cleaning the lint filter
The lint filter must be used during washing.
It must be cleaned in time after each using.
1. Take off the lint filter
Put hand at the indicated position.
Push down to take it off. ( See
Figure 1)
Figure 1
2. Clean the lint
Put it in water and clean while it is
still wet.(See Figure 2)
3. Install the lint filter
After cleaning, insert the bottom
of the lint filter ( marked with
"down side") into the overflow filter ,
then push the upper part of the
filter in ( marked with " up side ").
(See Figure 3)
Figure 2
Meaning and description of the symbols
Contents marked with that symbol are related
to the safety of the product and the personal
safety of the users. Please operate in strict
conformity to the contents, otherwise it may
cause damage of the machine or injure the
personal safety of the user.
Warning sign
Figure 3
Cleaning the overflow filter
Contents marked with that symbol are actions
forbidden to perform. Performing of those
actions may result in damage of the machine
or injure the personal safety of the user.
Too much lint on the overflow filter will influence
the normal usage of the machine. Please
clean it every two months.
Forbidding sign
Elastic fixing
claw
Take off the overflow filter.
As indicated in the figure, nip the elastic fixing
claw and pull it to the direction of the arrow to
take it off.
Please check if the power receptacle has good earthing
condition before using to guarantee your safety.
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety precautions
Please insert the power cord into
When the machine is normally
using, please put the power plug
at the location easily to be insert-
ed and extracted by hand. Be sure
to pull the plug off when there's
power failure, or the machine is
being moved, cleaned or when it
is idle.
special receptacle with rated vol-
tage.Be sure to use single-phase
three pins receptacle.The earthing
terminal of the receptacle must be
earthed reliably.If possible,please
adopt electric leakage protector.
Spinning
1.Put the laundries into the spin tub evenly and smoothly.
Earth
2.Press the gland in the tub properly. Close the inner and
outer cover of the spin tub.
If the supply cord is damaged,it must be replaced
by the manufacturer or its service
agent or a similarly qualified person
in order to avoid a hazard.
3.Spin
Select suitable spin time according to the laundries, and do spinning.
Do not use water hotter than 50 C .
Do not put the machine at damp
place like the bathroom . Never
wash it with water. Do not place
wet laundries on the control panel.
During spinning, if there is abnormal sound, it is generally owing to
slanting placement of the laundries. Please stop the machine and
reorder the laundries.
In spinning, it will pause the work if you open the outer cover of the
spin tub. Close it to resume the spinning.
For washing machine with ventilation
openings in the base, that a carpet
must not obstruct the openings.
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations.
To do spinning and draining and rinse
with water-filling together, please first
do spinning for around 1 minute, then
do draining or rinse with water-filling .
Otherwise the spinning will stop owing
to too much water stored in the spin tub.
Ventilation hole at
the bottom of the
washing machine
Do not let the machine share one receptacle
with other electric appliances. If the power
plug is damaged, or the plugging into the
receptacle is loose, do not use the plug any
more.
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety precautions
Do not stretch hands into the working
Do not decompose, repair or alter the
machine by yourself.
Rinsing
machine. It is dangerous even if the
rotation is slow. Take special care of
the children.
Rinse with water-filling
1.Put the laundries
Put the laundries into the wash tub. Select suitable current according
to the laundries.
2.Adjust the water level
Set the water level with water level adjusting lever according to the
laundries quantity. Then fill suitable water continuously.
Do not put any hot or heavy items
( such as the kettle with hot water )
on the washing machine.
Do not wash laundries with volatile
materials (such as thinner, petrol etc.).
3.Rinse
Adjust the wash timer to 5-7 minutes to do rinsing.
l
ro
et
er
inn
Th
P
Rinse with stored water
(Repeat the midway spinning and rinsing with stored water
for 2-3 times)
Keep the machine away from direct
sunlight and heat source like the
heater.
Handicapped or children without care
shall not use the machine.
1. Put the laundries into the wash tub. Select suitable current according to
the laundries.
2. Fill water to preset water level.
3. Rinse
Adjust the wash timer to 2-3 minutes to do rinsing.
When the laundries quantity is few, please use "Standard" current.
If you use "Strong" current, it may splash.
To protect your laundries and wash-
ing machine, please take out all of the
coins, buttons, sand, hairpin and
other foreign materials before washing.
Please check if the connection of the
water inlet pipe is proper.
It is suggested to use foamless washing
powder.
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and adjustment
Please install and adjust the machine according to the requirement of
the manual. It is very important to your security and correct operating
the machine.
Midway spinning
Install the lint filter
1.Put the laundries into the spin tub evenly and smoothly.
2.Spin
(1) Put the gland in properly.
After opening the package,please take out the lint
filter from the document bag,install it to the overflow
filter of the wash tub.See to the figure.
Overflow filter
Please put in the gland properly even if the laundries quantity is small.
Push
Gland
Lint filter
Push
Usage of the drain hose
Proper
Proper
The laundries
are slanting
The drainage shall be smooth with the drain hose.
No gland
1.The height of the drain hose shall be
less than 10cm , or the drainage will
not be smooth enough and cause
(2) Close the inner and outer cover of the spin tub.
<10cm
(3) Spin for 1-2 minutes.
Outer cover of
the spin tub
incomplete drainage.
2.Do not tramp or press the drain hose.
Inner cover of
the spin tub
3.If the drain hose is too long, cut it at mid point.
To make smooth drainage, cut the front end of
the hose slantingly.
3.Run the foam-removing spinning.
1
Set the inlet selector handle on spin side and
Water inlet
Inlet selector handle
fill water for about 1 min.
4.If extra drain hose is needed , please make
separate purchase. The inner diameter of the
extra hose shall not less than 30mm, and the
In case water flows out from wash tub side
due to too much inflow, please turn down
the water tap a bit.
Spin
Wash
>
30mm
length shall not exceed 1.5m.
<1.5m
2
Close the spin tub outer cover and spin
for about 1 - 2 min.
If the extra hose is too long, cut it either
at point A or B.
A
B
Download from Www.Somanuals.com. All Manuals Search And Download.
How to change the direction of the drain hoses
Washing sequence
Wash selector
Spin timer
Wash timer
(To set to below 2 minute,
Figure 1 indicates the ex factory installation
position of the drain hose.
(Strong current,
standard current)
(to set to below 1 minute,
first set to 2 minute then
turn it back. it can increase
the service life of the timer).
Side sectional view
first set to
5
minute then
turn it back. it can increase
the service life of the timer).
Drain hose
Fixing hook
fixing hook
installation hole
STRONG
OFF
Extend the drain hose from the side of spin tub.
OFF
Drain hose
Pull outwards
slightly
STANDARD
3
1
2
15
5
Take off the drainhose from the hanging
hole of the cabinet. Pull the drain hose
fixing hook outwards gently to take out
the drain hose from the twofixing hooks.
(As per Figure 2)
DRAIN
Take off
the drain hose
12
6
4
WASH SEELECTOR
SPIN TIMER
WASH TTIMER
3
Drain hose
fixing hook
9
Figure 1
Figure 2
Rotate the drainhose fixing hook for 90
to take it out from the installation hole
(As per Figure 3).
Wash
Install the two drain hose fixing hooks taken
out into the installation hole at the other side of
the base frame (to aim at the installation hole
accurately you can lean the washing machine
forward slightly).Then rotatefor 90 (As per Figure 4).
Rotate the fixing
hook for 90
Rotate the fixing
hook for 90
to fix it
1
Inlet selector
Take off the fixing
hook downwards
Insert the fixing hook into the
installation hole upwards
WASH
SPIN
(1) Set inlet selector to Wash side. Figure 1
(2 )Adjust water level rod to a position as needed.
Figure 1
Pull the fixing hook outwards slightly. Inlay the drain
hose into the fixing hooks reliably along the groove
at spin tub side, and make it extend towards spin
tub side..
Then hang thedrain hose into the hanging hole at
the spin tub side. (As per Figure 5).
Figure 4
Figure 3
2. Fill the water and add the dissolved washing
powder to make the water level reach the preset
position. (Figure 2)
Run washing program for some time to stir and
dissolve the powder completely.
Figure 2
Figure 3
Extend the drain hose from the back side
STRONG
STANDARD
Take out the drain hose from the two fixing hooks.
make it extend towards back side.(Extend the drain
hose from the side of back, hang the drain hose in
to the hanging hole at the both sides) . (As per Figure 6).
Figure 5
Figure 6
DRAIN
3.Put in the laundries. If the water quantity is
insufficient, please add water.
Install the water inlet hose; Select the water level
4.Select the current.
Select the strength of the current according to
the laundries. (Figure 3)
OFF
3
6
15
12
Water inlet hose
Insert the water inlet hose into the water-filling
entrance on the control panel directly.(pull it
out to dismantle it)
5.Select the washing time
Select the washing time according to the
laundries. (Figure 4)
Figure 4
9
Select water level according to the
quantity of the laundries.
Water level
indicator
STRONG
6.After washing,the buzzer will ring .Set
the "WASH SELECTOR" at "DRAIN".
(Figure 5).
Set the water level adjusting lever
to needed line.
STANDARD
Max.
Med
Min
Maximum
DRAIN
Use the new water inlet hose provided
with the machine to connect to the
water faucet.Old hose sets should
not be reused.
Medium
Figure 5
Minimum
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation before washing
Do s and Don ts
The capacity of washing and spinning of the
Preparation before washing
1.Connect the water inlet hose.
machine refer to the weight of the
standard laundries under dry condition that can
be washed or spinned in one time.
the largest capacity is only the loading capacity
of the drum
The thickness ,size , type of the cloth will influ-
ence the actual washing capacity. It is suit-
able to put in reasonable amount of laundries
and the laundries can be turned round in wash-
ing for one time washing.
2.Confirm that the washing machine is earthed
reliably . Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.
3.Put down the drain hose .
Do not select " Maximum " water level for
laundries less than 1.5kg, so as to avoid
splashing of water.
4.Slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally.
It is suggested not to use high sudsing detergent.
Usage of the detergent
Pay attention to following before washing the laundries
Check if
The quantity of
When the pulsator
How to use the whitener
How to use the washing powder
Clear the
Tie the long
strips; fasten
the buttons;
close zippers.
the laundries
has special
requirement
on washing
the laundries is running , the
shall not be too buttons of the
large. Stretch laundries may
and loosen the cause noise. For
laundries before the sake of
pocket. Take
out the coins,
sand, hairpins
etc.
Direct dissolved in the machine:
1.Fill small quantity of water.
2.Add the powder . Run for 30
seconds to dissolve it completely.
3.Put in laundries. Select suitable
water level.
Fill water to decided level. Dilute
the whitener with container.
Pour it slowly into the washing tub.
putting them in discretion, please
the tub.
put the laundries
with buttons into
other laundries.
Avoid using whitener on laun-
dries with color or pattern as they
are prone to lose color.
The instant dissolving of the washing
powder:
1.Prepare warm water of 30 C and a
container.
2.Add the powder while stirring to fully
dissolve it.
The powder is more prone to pollute the
laundries than the detergent. Therefore
please use it with proper quantity.
The whitener shall not touch
the laundries directly.
Refer to the user's manual for
the usage and quantity of the
whitener.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like
mud or dust. For the parts with heavy soil, please apply detergent on
them in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn
it over before putting in.
For powder whitener, please
dissolve it before using.
Dosage of different washing powder is
different. Please refer to the instruction
of the washing powder for the detail
dosage.
f. Do not put those laundries polluted by chemicals into the washing
machine directly.
Download from Www.Somanuals.com. All Manuals Search And Download.
|