PLASMA TV
OWNER`S MANUAL
MODEL: PH-4210D
Please read this manual carefully and completely before
operating the unit, and retain this manual for future
reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Read all of the instructions before using this appliance. When using this
appliance, always exercise basic safety precautions, including the following:
1)Save these Instructions ---the safety and operating instructions should be
retained for future reference.
2)All warning on the appliance and in the operating instructions should be followed.
3)Cleaning --- Unplug from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use only dry cloth for cleaning.
4)Attachments ---do not use attachments not recommended by the manufacturer
as they may cause hazards.
5)Water and moisture -- do not place this product near water, for example, near a
bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a
swimming pool.
PORTABLE CART WARNING
6)Accessories ---do not place this unit on an unstable cart, stand,
(symbol provided by RETAC)
tripod, bracket, or table. Use only with a cart, stand, tripod, bracket,
or table recommend by the manufacture, or sold with the unit.
7)Ventilation ---Slots and openings in the cabinets and the back or
bottom are provided for ventilation. These openings must not be
blocked. In a built in installation such a bookcase or rack do not
install product unless proper ventilation is provided.
S3126A
8)Power Source ---this TV should be operated only from the type of power source
indicated on the rating label. If you are not sure of the type of power supply to your
home, consult your appliance dealer or local power company.
9)Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet. To prevent electric shock, ensure
the grounding pin on the AC cord power plug is securely connected.
10)Power cord protection ---Power supply cords should be routed so that they are
not likely to be walked on or pinched by items placed upon or against them. Pay
particular attention to cords or plugs, convenience receptacle, and the point where
they exit from the appliance.
11)Lighting precaution ---for added protection for this product during a lighting
storm or when it is left unattended for long period of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will prevent damage to the
product due to lighting and power line surges.
12)Never push objects of any kind into this product through openings as they may
touch dangerous voltage point or short out parts that could result in a fire or electric
shock. Avoid spilling liquid of any kind on the product.
13)Servicing ---do not attempt to service the product by yourself, as opening or
removing covers may expose you to dangerous voltage or other hazards. Refer all
servicing to authorized service personnel.
14)Unplug this unit from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power supply cord or plug is damaged or frayed.
Owner s Manual 3
Download from Www.Somanuals.com. All Manuals Search And Download.
b.If liquid has been spilled, or objects have been fallen into the unit.
c.If the unit has been exposed to rain or water.
d.If the unit does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions, as
improper adjustment of other controls may result in damage and will often
require extensive work by a qualified technician to restore the unit to its normal
operation.
e.If the unit has been dropped or damaged in any way.
f.When the unit exhibits a distinct change in performance; this indicates a need
for service.
15)Heat --- The product should be situated away heat sources such as radiators, heat
registers, stoves, or other products (Including amplifiers) that product heat.
16)Overloading ---Do not overload wall outlets and extension cord as this can result
in a risk of fire or electric shock.
4 Plasma TV
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning..............................................................2
Safety Instructions............................................ 3-4
Prog. Switch.......................................................19
Picture Quality adjust
Picture QualityAdjust .........................................20
Sound Adjustment
Introduction
Controls...........................................................6
Connection Options...........................................7
Remote Control KeyFunctions...........................8
Installing Batteries............................................8
Sound Adjust......................................................21
Adjustment Setup
Adjustment Setup...............................................22
Function Setup
Function Setup...................................................23
Menu Menu LanguageOption ..............................23
Menu Timeout Option.........................................23
Menu Background Option....................................23
Calendar Display andCheck ...............................23
Auto Off.............................................................23
BlueScreen .......................................................23
Close Caption....................................................24
Parental............................................................24
Time Setup............................................................25
Clock Setting ....................................................26
Off/On time .......................................................26
Rimind Time/RemindProg. .................................26
Lock Menu Options
Installation
Installation instructions....................................9
VCR Setup.......................................... .......... 10
Cable TV Setup................................... .......... 10
External A/VSource Setup...............................11
DVD Setup.....................................................11
DTV Setup .....................................................12
Monitor Out Setup...........................................12
PC Setup.......................................................13
Install the Speakers........................................14
Install the Stand.............................................15
Install the Standto the Plasma........................ 15
Operation
Lock Setup........................................................27
Change Password..............................................27
Tuning Lock.....................................................27
Preset Prog. ....................................................27
Prog. Num .......................................................28
Source Lock.................................................... 28
Child Lock....................................................... 28
Max Volume.....................................................28
Unlock............................................................ 28
Screen Menu Options............................................. 28
Auto Adjustment ................................................29
Setting Picture Format.......................................29
Screen Position ................................................29
Troubleshooting Checklist...................................... 30
Maintenance......................................................... 31
Product Specifications........................................... 32
Warranty ...............................................................33
Turning theTV On
Turning on the TV .......................................16
Choose the MenuLanguage ........................16
Choose the InputSource .............................16
Basic Function
Operation Menu..........................................17
Sound Mode................................................17
Picture Mode...............................................17
Sleep Timer.................................................17
System Menu
Channel Type ................................................18
CATV Type ....................................................18
Automatic Scan..............................................18
Fine Tune......................................................19
Color System ................................................19
Skip ..............................................................19
Setup and Operation Checklist
(See pages 10~15 for available connection and operational setup options.)
1. Unpack TV and all accessories.
2. Connect all external video and audio equipment. See pages 10 ~ 13.
3.Install the speakersand stand. seepages 14~16 .
4. Install batteriesin remote control. See page 8.
5. TurnTV on. See page 16
6. Turn video source equipmenton.
Owner s Manual 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Front panel controls
EXIT
INPUT CH-
CH+
VOL- VOL+ MENU
Menu enter /exit
Power On/Off Button
Signal source selection
Power Standby Indicator
illuminates red instandby mode,illuminates bluewhen
the display isturned on
Down/Up. Select desired optionon MENU ortune
to the desiredchannel.
Remote Control Sensor
VOLUME Buttons
MENU Button
6
Plasma TV
Download from Www.Somanuals.com. All Manuals Search And Download.
Real panel controls
S-Video Input
VGA Input/Audio input
DVI Input/Audio input
connect your cable/PC
through the input
Power On/Off
Earphone port
ON OFF
VGA IN
AV IN
COMPONENT IN
DVI IN
AV OUT
R
L
AC-INPUT
AUDIO OUT
VGA
AUDIO
VIDEO
S-VIDEO
L-AUDIO-R
ANT IN
Pr/Cr
Pb/Cb
Y
L-AUDIO-R
DVI
AUDIO
VIDEO
L-AUDIO-R
Audio/Video Input
Connect audio/video
output from an external
device to these jacks
DVD/DTV Input
Connect a component video/audio
device to these jacks
AUDIO output
External audio/
video output
Antenna Input
Connect cable or antenna signals to
the TV, either directly or through your
cable box.
Power Cord Socket
This TV operateson AC power. Thevoltage is
indicated on thespecifications page. Never
attempt to operate the TV onDC power
Owner s Manual 7
Download from Www.Somanuals.com. All Manuals Search And Download.
When using the remote control. Aim it towards the remote sensor on the TV.
Function introduction
FREEZE
Freezes the currently-viewedpicture.
INPUT
Select the sourceinput mode.
SLEEP
Press this keyto set sleeptimer.
MUTE
Switches the soundon or off
PC
Select PC source
INPUT
MUTE
POWER
DISPLAY
PC
FREEZE
SLEEP
POWER
Turns your TV or any other programmed
equipment on oroff, depending on mode.
AUTO
Auto adjust forPC
AUTO
display
Display of currentchannel
signals, program andsystems
Digits
FAVORITE
no available
Program direct option(when edit program,
every press can set different sign by turns among
the digits and sign on top of them)
MTS/SAP
Selects MTS sound: Mono, Stereo, and
SAP in Analog mode. Change the audio
Menu Language in DTV mode.
Q.VIEW
EXIT
-
Q.VIEW
Switch from thecurrent channel tothe
previous channel viewed.
MTS/SAP
CH+
MENU
Brings up themain menu tothe screen.
EXIT
Clears all on-screendisplays and returnsto
TV viewing fromany menu.
VOL-
VOL+
MENU
CH-
CHANNEL UP/DOWN
Selects available channels programmed
with channel Scan.
VOLUME UP/DOWN
Increases/decreases the soundlevel.
P.STD
CC
CC(Closed Caption)
AVC
P.STD
Selects a factorypreset picture mode
depending on theviewing environment.
RATING
set the parentalcontrol.
S.STD
LOCK
RATING
ARC
ARC
Changes the aspectratio.
S.STD
Selects the audiostyle appropriate for
the program.
CALENDAR
DNR
AVC
Automatic Volume Control
LOCK
Press to enterthe Lock Setmenu.
DNR
Digital noise reduction
CALENDAR
1
2
3
Installing Batteries
Open the batterycompartment cover onthe back sideand install
the batteries matchingcorrect polarity (+with +, -with -).
Install two 1.5VAA batteries. Don`t mixold or usedbatteries with
new ones.Replace cover.
8 Plasma TV
Download from Www.Somanuals.com. All Manuals Search And Download.
Ensure that thefollowing accessories areincluded with yourplasma display. If anaccessory is missing, please contact the
dealer where youpurchased the product.
PC
VIDEO
DVI
INPUT
MUTE
POWER
AUTO
DISPLAY
MENU
AVC
DNR
EXIT
ENTER
P.STD
VOL+
LOCK
CALENDAR
VOL-
ARC
S.STD
/
SAVING
RATING
CC
SURROUND
SLEEP
FREEZE
HDMI to DVI
Adaptor
Audio/Video Audio Cord
Cord
ST4X16
Screw(x16)
(2.5MX2)
Connection cord
Speaker unit(X2)
Connecting block X4
M4X12Screwsx8
M5X16Screwsx4
Brace pole x2
4
Standx1
- The TV can be installed invarious ways suchas on awall, or ona desktop etc.
- The TV is designed to bemounted horizontally.
Power
Supply
GROUNDING
Ensure that youconnect the earthground wire toprevent possible electric
shock. If groundingmethods are notpossible, have aqualified electrician
install a separatecircuit breaker.Do not tryto ground theunit by connecting
it to telephonewires, lightening rods,or gas pipes.
Short-circuit
Breaker
Owner s Manual 9
Download from Www.Somanuals.com. All Manuals Search And Download.
- To avoid picture noise (interference), leave an adequate distance between the VCR and TV
Do not leave a still picture from a VCR on the screen for an extended period. If the 4:3 format is used, the fixed images on the
sides of the screen may remain visible on the screen if this format is used day after day. This is known as burn-in, and it
is an uneven wear of the screen area. Reduce contrast when displaying fixed images on the screen for long periods.
1. Connect the audioand video cablesfrom the
VCR's output jacksto the TV input jacks,
as shown inthe figure.
ANT IN
When connecting theTV to VCR, match
the jack colors(Video = yellow, Audio Left =white,
and Audio Right = red).
If you connectan S-VIDEO outputfrom VCR to
the S-VIDEO input, the picture qualityis
improved; compared toconnecting a regular
VCR to theVideo input.
2. Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner`s
manual.)
3. Select the input source by the INPUT button
on the remote control.
Do not connect both Video and
S-Video at the same time.
If you connect both Video
and the S-Video cables, only the
S-Video will work. Do not connect
S-Video if you want to use the
Video connection.
- After subscribing to a cable TV service from a local provider you can watch cable TV programming. The TV cannot
display TV programming unless a TV tuner device or cable TV converter box is connected to the TV.
- For further information regarding cable TV service, contact your local cable TV service provider(s).
1. Connect the co-axialcable from yourwall jack tothe
antenna in ofthe TV for direct cableprogramming.
ANT IN
2. If you havea cable box, connect the audioand video cablesfrom the
cable box's outputjacks to theTV`s AV IN input jacks, as shown inthe figure.
When connecting theTV to a Cable Box, match the jackcolors
(Video = yellow, Audio Left =white, andAudio Right =red).
(If you havea digital cablebox please referto page 12, for DTVsetup)
3. Select theinput source byusing the INPUTbutton on the
remote control. (Ifconnected toAV IN, select AV1/S-VIDEO input source)
4. Select your desired channel with the remote control for cable box.
(Co-axial)
10 Plasma TV
Download from Www.Somanuals.com. All Manuals Search And Download.
How to connect
Connect the audioand video cablesfrom the external
equipment's output jacksto the TV`s AV IN input jacks, asshown in
the figure.
When connecting theTV to external equipment, match the
jack colors (Video = yellow, AudioLeft = white, and Audio
Right = red).
How to use
1. Select the inputsource by usingthe INPUT button on
the remote control.
2. Operate thecorresponding external equipment. Refer to
external equipment operatingguide.
How to connect
1. Connect theDVD video outputs(Y, Pb, Pr)to the COMPONENT
(Y, Pb, Pr)IN jacks onthe TV and connect theDVD
audio outputs tothe AUDIOINPUT jacks on the TV, as
shown in thefigure.
2. If your DVDonly has anS-Video output jack, connect thisto the
S-VIDEO input onthe and connectthe DVD audio
outputs to theAUDIO INPUTjacks on theTV, as shown
in the figure.
NOTE: If your DVD player does not have component video output,
use S-Video or composite(AV) .
How to use
1. Turnon the DVDplayer, inserta DVD.
2. Use theINPUT button on theremote control
to select YPbPr/YCbCr . (If connectedto S-VIDEO,
select theAV1/S-VIDEO external inputsource.)
3. Refer tothe DVD player'smanual for operatinginstructions.
Component Input ports
To get better picturequality, connect a DVDplayer to thecomponent
input ports asshown below.
Component ports
on the TV
Video output ports
on DVD player
Owner s Manual 11
Download from Www.Somanuals.com. All Manuals Search And Download.
- To watch digitally broadcast programs, purchase and connect a digital set-top box.
Digital Set-top Box
How to connect
Use the TV`s COMPONENT (Y, Pb, Pr)INjacks, VGAor DVI INport for
video connections, dependingon your set-topbox connections available.
Then, make thecorresponding audio connections.
YPbPr/YCbCr
VGA
Yes
Yes
Yes
Yes
No
DVI
No
Yes
Yes
Yes
No
Signal
480i
How to use
1. Turnon the digitalset-top box. (Referto the owner`smanual for thedigital
set-top box.)
Yes
Yes
Yes
Yes
Yes
480p
720p
1080i
1080p
2. Use INPUT on the remotecontrol to selectYPbPr/YCbCr, VGA, or DVI source.
The TV has a specialsignal output capabilitywhich allows
you to hookup a secondTV or TV.
Connect the secondTV or TV to the TV`s AV OUT.
See the OperatingManual of thesecond TV or TV for further
details regarding thatdevice`s input settings.
NOTE
YPbPr/YCbCr, VGA, DVI input sources cannot be used for monitor out.
12 Plasma TV
Download from Www.Somanuals.com. All Manuals Search And Download.
How to connect
1. To get the best picture quality, adjust the PC
graphics card as required.
2. Use the TV`s VGAIN or DVI(Digital Visual
Interface) IN portfor video connections, depending
on your PCconnector.
If the graphiccard on thePC does notoutput
analog or digitalRGB simultaneously, connect
only one ofeither VGAIN or DVIIN to displaythe PC
on the TV.
If the graphiccard on thePC does outputanalog
or digital RGBsimultaneously, set the displayto
either VGAor DVI; (theother mode isset to Plug
and Play automaticallyby the display.)
3. Then, make the correspondingaudio connection. If
using a soundcard, adjust thePC sound asrequired.
How to use
1. Turn on the PC.
2. Turn on the display by pressing the POWER button on the TV's remote control.
3. Use INPUT on the remote control to select VGA, or DVI source.
4. Check the image on yourTV. There may be noise associated with the resolution, vertical pattern, contrast or
brightness in PC mode. If noise is present, change the PC mode to another resolution, change the refresh rate to another rate
or adjust the brightness and contrast on MENU until the picture is clear. If the refresh rate of the PC graphic card can not
be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.
NOTES:
Use a DVIcable.
Avoid keeping a fixedimage on the's screen fora long periods. The fixed image may become
permanently imprinted onthe screen. Usea screen saverwhen possible.
The synchronization inputform Horizontal andVertical frequenciesare separate.
DVI to HDMI connecting
How to connect
1. Use the TV`s DVI portfor HDMI toDVI adaptor connection,
then use the HDMI to HDMIcable for theHDMI to DVIadaptor
connection.
2. Connect the audioand video cablesfrom the external
equipment's output jacksto the TV`s audio jacks, as shown in
the figure.
HDMI to DVI
Adaptor
(supported)
Audio cable
(supported)
How to use
1. Turn on the device. (Refer to the owner`s manual for device.)
2. Use INPUT on the remote control to select DVI source.
HDMI to HDMI
cable
(no supported)
HDMI
Device with HDMI jack
Owner s Manual 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Speakers
1 Face the Plasma screen upside down on a clean blanket and pay attention not to indent the casing.
Lay the two speaker aside of the Plasma.
2. Fix 4 ST4X16 screws to the speaker.
3.Lean the speakeragainst the plasmascreen, ensuring thatthe screw holeson the connectingblock are in
Line with the screw holes on the plasma screen then hold the speaker in place.
4. Fix the speaker tothe plasma screenwith ST4X16 screws.
5. Connect the speaker to the speaker terminal of plasma screen: Nip the speaker terminal and insert the
connecting cable intothe terminal slot. Release the speakerterminal and ensurethat the white
connecting cable is inserted in the terminal slot marked red and black connecting cable is inserted in the
black terminal slot, and that anode and cathode poles are correctly connected.
(See Figure )
ST4X16 screw
ST4X16 screw
EXT SPEAKER
R
L
14 Plasma TV
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Stand
Insert the supporting bracket with 8 M4x12 screws to
the installation holes on the bottom of the soleplate.
Fasten the Supporting bracket and the Soleplate
as shown in figure.
Installing the Stand to the Plasma
Face the Plasmascreen upside downon a cleanblanket and payattention not toindent the casing.
Lay down thestand and putit to respondingposition of thePlasma screen ,andmake sure thebrace pole istowards the holeof
the Plasma.
Affix the 2 Plasma bracepoles to theunit on theback of theplasma display with4 M5X16 screws.
Owner s Manual 15
Download from Www.Somanuals.com. All Manuals Search And Download.
In this manual, the OSD (OnScreen Display) maybe vary fromwhat is dispayedon your set.
What is shownin this manualis an exampleto help youwith the operartionof your set.
TV
Turning on the TV just after installation.
1. Connect powercord correctly tothe television.
2. Press the SWITCHbutton on backof the TV. The TV is powered upand set into standby mode.
Press the POWERbutton on theremote control orbutton on theTV and then the TV will turnon.
Turning on the TV
1. If the TV was turnedoff with the SWITCH buttonon the TV
Press the SWITCHbutton on theTV to turn the TV on.
2. If theTV was turned off with the remotecontrol and thenthe ON/OFF switchon the backof the TV.
Press the SWITCHbutton on theback of TV and thenpress the POWERbutton on theremote control toturn
the TV on.
NOTE
If the unitis not usedfor an extendedperiod, disconnect thepower plug fromthe wall poweroutlet.
Choose the Menu Language
When you start using your set for the first time, you must select the Menu Language which will be used for displaying
menus and indications.
1 Press MENU and then use VOL+/- button to select the
FUN. Menu.
Menu Language
OSD Timeout
Menu Background
Calendar
English
15seconds
Translucent
2 Press CH+/-button to select Menu Language.
3 Select a particular Menu Language by pressing VOL+/- button
repeatedly. You can choose oneof three MenuLanguages.
(English, French, Spanish)
Auto Off
Off
Off
Off
BlueScreen
Close Caption
Parental
4 When you are satisfied with your choice, press the EXIT button to
return to normal viewing.
A
B
C
Choose the Input Source
- This changes the picture source so that you can watch your TV, cable TV, VCR, DVD, or any other devices that
are connected toyour TV.
Source
1. Press INPUT button on theremote control andthe Scoure menuwill appear onthe screen.
2. Press CH+/-buttonfor each optionand then pressVOL+/- button toconfirm.
TV
AV1/S-Video
YPbPr/YCbCr
VGA
Note:
If AV1 and S-Video are insertedat the sametime, priority willbe given toS-Video.
DVI
16 Plasma TV
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Functions
Operation Menu
1.Press MENU buttonto open themain menu. PressVOL+/- button to selectthe PIC., SOU., ADJ., SYS. , FUN. orTIME menu.
2.Press CH+/- buttonto select submenu, and press VOL+/- button to increase/decreasethe value orselect the setup.
3.Press MENU toreturn to themain menu.
4.The setup timein display willdisappear automatically whenthe latest presettime expiries. MENUdisplay time can
be set to5,10,15,20,25,30 and 40seconds.
5.Press EXIT button to exitany menu ifMENU is ondisplay.
Sound Mode
Press S.STD button on the remote control to display the menu, and then use CH+/- button to select
the desired mode, press VOL+/- toconfirm.
SOU.Mode
(This feature canalso be changedfrom the soundmenu function screen)
Music
Standard
Custom: A spare setting that can be adjusted to personal tastes.
Theater
Standard: Normal sound withmoderate bass andtreble setting.
Custom
Music: Adjust the sound to best suit music programs.
Theater: Enables extra bassand treble toenhance the movieexperience.
Picture Mode
Press P.STD button on the remote controller for menu display, and then use CH+/- button to select
the desired mode, press VOL+/- toconfirm.
PIC.Mode
(This change canalso be madefrom Picture menuadjustment screen)
Vivid
Standard
Standard: normal mode.
Mild
Vivid: for watching highspeed footage andsharp images.
Custom
Mild: for softening theimage and smoothingoverall picture.
Custom: picture effect which you favorite.
Sleep Timer
Every press ofthe SLEEP button, the timerwill be setin the followingsequence:
Sleep 0Min Sleep 5Min Sleep 15Min Sleep 30Min Sleep 60Min Sleep 90Min Sleep 120Min Sleep 0Min
If remaining timeof set timeris to bedisplayed, press theSLEEP button once.
Owner s Manual 17
Download from Www.Somanuals.com. All Manuals Search And Download.
System Menu
This TV set has three methods to set channels: Automatic search, manual search, and fine tune.
In this section, how to use the remote control to set channels is explained. You can also use the
buttons on the TV set to set channel.
Channel Type
Before your television can begin memorizing the available channels, you must specify the
type of signal source that is connected to the TV (i.e., an antenna or a cable system).
1 Press MENU button and then use VOL+/- button to select the SYS. Menu.
2 Press CH+/- buttons to select "Channel Type" item.
Color Sys.
Sound Sys.
Fine Tune
Skip
AUTO
M/N
3 Press VOL+ buttonto select Cable or Air item.
49.75MHz
Off
Channel Type
CATV Type
Auto Scan
Cable
STD
When Air is selected, theTV will detectantenna signals andwill search
for antenna TVchannels available inyour local area.
When Cable is selected, theTV will detectcable company supplied
signals and willsearch for cableTV channels availablein your area.
Make sure thatregistration with yourcable TV providerand connection
of equipment arecompleted.
A
B
C
When Air and Cable are selected, theTV will detectthe antenna
signals and cablecompany supplied signals, and search forthe
antenna TV andcable TV channelsavailable in yourarea.
Note : the tuning menu can only be
operated in normal TV mode.
CATV Type
1 Press MENU button and then use VOL+/- button to select the SYS. Menu.
2 Press CH+/- buttons to select "CATV Type" item.
3 Press VOL+ buttonto select STD, IRC or HRC item.
Note: STD, HRCand IRC identify various types of cable TV systems.
Contact your local cable company to identify the type of cable system
that exists in your particular area.
Automatic Scan
Color Sys.
Sound Sys.
Fine Tune
Skip
AUTO
M/N
1 Press MENU button and then use VOL+/- button to select the SYS. Menu.
2 Press CH+/- buttons to select "Auto Scan" item.
49.75MHz
Off
Channel Type
CATV Type
Auto Scan
Cable
STD
3 Press VOL+ button to ensureautomatic search function work.
4 Press MENU button to stop automatic search function.
A
B
C
After the search has finished, all available channels
will be automatically preset in order.
18 Plasma TV
Download from Www.Somanuals.com. All Manuals Search And Download.
System Menu
Color Sys.
Sound Sys.
Fine Tune
Skip
AUTO
M/N
Fine Tune
If the picture and/or sound are poor, try using the fine tune feature.
Do not use this feature unless reception is poor.
49.75MHz
Off
Channel Type
CATV Type
Auto Scan
Cable
STD
1 Repeat step 1-2, then press CH+/- buttons to select "Fine Tune" item.
2 Press VOL+/- buttons repeatedly to carry out fine tune, until the best
picture and sound are obtained, then release the button.
A
B
C
Color System
Color Sys.
Sound Sys.
Fine Tune
Skip
AUTO
M/N
Usually this should be set in the auto position. However if the color displayed
on the screen is incorrect, you can manually select thecorrect color system.
Press MENU and then VOL+/- button, till the picture menu shown on the
right will display on the screen.
49.75MHz
Off
Channel Type
CATV Type
Auto Scan
Cable
STD
Press CH+/- buttons to select"Color Sys.", then press the VOL-/+ buttons
to select the correct colorsystem. In general, you canset it to "AUTO".
A
B
C
Skip
After the channels are preset, you can skip some programs to select your favorite preset channels only.
1. Press CH+/- button or Direct-digit buttons to select a channel.
2.Press MENU and then use VOL+/- button to select the SYS. Menu.
Color Sys.
Sound Sys.
Fine Tune
Skip
AUTO
M/N
3.Press CH+/- buttons to select "Skip" item.
4. press VOL+/- button to set Skip as On.
49.75MHz
Off
5. When you are satisfied with your choice, press the MENU button to return to
the previous menu or press EXIT button to return to TV viewing.
Channel Type
CATV Type
Auto Scan
Cable
STD
If you want to recover the skipped channel
1. Use Direct-digit buttons to select the number of the channel to
be recovered.
2. Do the above steps again.
A
B
C
3. Press VOL+/- button to set Skip as Off.
Owner s Manual 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Quality Adjustment
Picture Quality Adjustment
The TV menu gives you an overview of MENU you can select to adjust picture quality.
Note: Depending on the input signal, one or more menu items may not be selectable.
1 Press MENU and then use VOL+/- button to selectthe PIC. Menu.
2 Press CH+/-button to select the desired items.
Mode
Custom
50
3 Press VOL+/- button to adjustthe setting.
Contrast
Brightness
Color
50
50
0
4 When you aresatisfied with yourchoice, press the MENU button to returnto
the previous menuor press EXIT button to returnto TV viewing.
Hue
Sharpness
DNR
50
Auto
Contrast
This will adjust the intensity ofbrighter parts of the picture but keep
the dark parts unchanged.
A
B
C
Brightness
This will adjustthe light outputof the completepicture, which will
mainly affect the darker areasof the picture.
Color
This will adjustthe saturation levelof the colorsto suit yourpersonal preference.
Hue (selectable in NTSCmode only)
Allows you toselect the colormix (Hue) ofthe picture.
Sharpness
This will adjustthe sharpness offine details inthe picture.
DNR (Digital Noise Reduction )
Automatically filters out and reduces the image noise and improves picture
quality when receiving weak video signals.
Select Auto/Off/Weak/Medium /Strong according to the image noise of the broadcast signal.
Note:
When Custom mode is not selected, the Custom mode can be entered automatically if Contrast, Brightness,
Color, Hue and Sharpness parameters are adjusted.
20 Plasma TV
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound adjustment
Sound Adjust
Sound can beadjusted for anyinput as follows:
Volume
Balance
SOU.Mode
Treble
50
0
1. Press MENUbutton and thenuse VOL+/- buttonto select theSOU.menu.
2. Press CH+/- button for desiredoption.
Personal
50
3. Afteryour option isselected, press VOL+/-button to adjust.
4. Repeat step 2and 3 untildesired sound hasbeen achieved.
If there isno selction madeduring the standarddisplay time , the MENU will
disappear. Ifthe MENU orEXIT button is pressed , MENU display willdisappear
in sequence orimmediately.
Bass
70
Surround
AVC
Off
Off
Woofer
Off
Volume
This will adjustthe sound outputlevel.
A
B
C
Balance
This will adjust the output of the right and left speakers to obtain the best
stereo reproduction for your listening position.
SOU. Mode
This select themodes for soundreproduction dependent onthe broadcast signalsor signals fromexternal inputs received.
Press CH+/- buttonto Select SOU.Mode,
press VOL+/- buttonto select theMusic Standard Theater or Personal.
Treble
This will adjustthe treble outputlevel.
Bass
This will adjustthe bass outputlevel.
Surround
The surround sound feature expands the audio listening field wider and deeper to create exceptional sound quality
from the TV`s speakers.
Press CH+/- button to Select Surround,
press VOL+/- button to set Surround as Off or On
AVC (Automatic Volume Control)
Each broadcasting stationhas its ownsignal conditions, andso it isnot easy foryou to adjustthe volume everytime the
channel is changed. This feature lets you automaticallyadjust the volumeof the desiredchannel and reducesthe volume
differences between channels and programs, providing a moreconstant overall level.
This will alsoreduce the dynamicsof sound.
Press CH+/- buttonto Select AVC,
press VOL+/- buttonto set AVC as Off or On
Woofer
Woofer is a speaker thatcomplements front speaker`sreproduction capability oflow-pitched sound.
Press CH+/- buttonto Select Woofer,
press VOL+/- buttonto set Woofer as Off or On
Note:
1. Select Balanceto balance rightand left soundchannels of theTV. The intermediate value is 0. When the indicationvalue of
Balance increases toward+50, sound of theright speaker isstronger and theleft speaker becomesweaker. Whenthe indication
value of Balancedecreases toward -50, sound out ofthe right speakeris weaker andleft speaker becomesstronger.
2.When Personal modeis not selected, the Personal modewill be enteredautomatically if Treble or Bass parameters areadjusted.
Owner s Manual 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjustment Setup
Adjustment Setup
VGA/DVI:
In VGAand DVI inputmode , HPosition and VPosition can beused to
adjust the pictureposition.
Display Mode Full Screen
Adjust
RGB
When VGA DVI input modeis set
1. Press MENUbutton on theremote controller andthen use the
VOL+/- to selectthe ADJ.menu.
Reset
Auto Sync.
Press CH+/- toenter MENU ofpicture position setupMENU
2.
Color Temper.
Black Stretch
Standard
On
3. Press theVOL+ button andthen use CH+/-button for desired
adjust parameter option.
Not selectable
A
B
C
4. Press VOL+/-for desiredadjust parameter optionuntil a satisfactory
value is achieved. When VGAsignals are received, the automatic
mode is usedfor parameter adjustment.
Note:
Adjust, RGB andReset are functionalonly under VGAand DVI mode, and AutoSync is functionalonly in VGAmode.
Display Mode
This will adjust the picture aspect ratio.
0
0
0
0
H Size
Under the VGAsignal, there are Full Screen , one to one and 4:3
modes for selction under Display mode.
H Position
V Size
Under the AV1or S-Video signal, there are Full Screen, Vertical Zoom,
Half Zoom, Panorama and 4:3 Modes to select forDisplay Mode.
Under the DVI signal, there are Full Screen and 4:3 Modes
to select forDisplay Mode .
V Position
Phase Adjust
0
A
B
C
Adjust
This is used for adjusting H Position and V Position as well as
relative parameters in VGA and DVI modes.(Phase Adjust is not
available in DVI)
0
0
0
Red
RGB
Green
Blue
This is used for the adjustment of the numerical value of red, green and
blue in VGA/DVI mode.
Reset
This is used to reset thedefecult setting parameters (After the operation,
Complete will be on the right of the option)
A
B
C
Auto sync
This is used for adjustment of picture location frequency and phase
parameters in VGAmode. (Not availablein DVI)
( Afterthe operation, Completewill be onthe right ofthe option.)
Color temperature
This will increase or decrease Warm (red) and Cold (blue) colors to suit
personal preferences.
Select Cold to give the white colors a blue tint, Standard to give the white
colors a neutral tint, Warm to give the white colors a red tint.
22 Plasma TV
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Setup
Function Setup
It is possible to select Menu Language, OSD translucency, position and screen display of the MENU as follows:
1. Press MENU button once, and then use VOL+/- button until the following menu appears on the screen:
2. Press theVOL+ button andthen use CH+/-button on theremote controller toenter MENU ofsystem setup.
3. Press CH+/-to select desiredoption on MENU.
AV1
4. Press VOL+/- to adjust selectedoption.
Menu Language
OSD Timeout
Menu Background
Calendar
English
15seconds
Translucent
Menu Language Option
Auto Off
Off
Off
Off
Repeat step 3and 4 toselect English, Francaisor Espanol asthe MENU Language.
BlueScreen
Close Caption
Parental
OSD Timeout Option
A
B
C
Repeat step 3 and 4 to select menu display time to 5,10,15, 20, 25, 30 or 40 seconds.
Menu Background Option
Repeat step 3and 4 toselect OSD backgroundas Translucentor Opaque.
Calendar Display and Check
Repeat step 3 and press VOL+/- button to enter calendar menu as follows:
Enter Calendar menu, press VOL+/- and CH+/- button to
adjust or check the date.
Auto Off
Repeat step 3and 4 toselect On/Off. If On isselected, and thereis no signalto the TV for 2minutes , Auto Off will
be on thescreen and for3 minutes theTV will be in standbycondition . If Off is selected , andthere is nosignal to the
TV for 3minutes without anyoperation , no signal will be onthe screen .
BlueScreen
Repeat step 3and 4 toselect blue Screenbetween off or on.
Owner s Manual 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Closed Caption
Closed captioning isa process whichdisplays the audioportion of atelevision program
as written wordswhich then appearas subtitles onthe television screen. Closed
captions allow viewersto read thedialogue and narrationof television programs.
Menu Language
OSD Timeout
Menu Background
Calendar
English
Using Closed Captions
15seconds
Translucent
Captions are the subtitles of the dialogue and narration of television programs.
For some programs, program dialogue can be arranged into captions in
advance. Its possible to caption live programs by using a process called real-time
captioning, which creates captions instantly. Real-time captioning is normally
done by professional reporters using a machine shorthand system and computer
for translation into English.
Auto Off
Off
Off
Off
BlueScreen
Close Caption
Parental
Captioning is an effective system for the hearing-impaired, and it can also aid
in teaching language skills.
A
B
C
1. Press the MENU button and then use VOL+/- button to select the Fun. menu.
2. Press CH+/- to select Close Caption.
3. Press the VOL+ button to select available caption items.
(Off/CC1/CC2/CC3/CC4/TX1/TX2/TX3/TX4/XDS.)
TEXT
The term forthe captions thatappear in alarge black framethat almost cover
the entire screen;usually these messagesare provided bythe broadcaster.
4. Press EXIT button to return to TV viewing.
Parental Guidance
Parental Control can be used to block specific channels, ratings and
Menu Language
OSD Timeout
Menu Background
Calendar
English
other viewing sources.
15seconds
Translucent
The Parental Control Function is used to block program viewing
based on the ratings sent by the broadcasting station.
The default setting is to allow all programs to be viewed.
It is also possible to block all program viewing for a time period.
To use this function, the following must be done :
1. Set ratings and categories to be blocked.
2. Specify a password
Auto Off
Off
Off
Off
BlueScreen
Close Caption
Parental
A
B
C
3. Enable the lock
Rating and categories
Rating guidelines are provided by broadcast stations. Most television
programs and television movies can be blocked by TV Rating and/or
Individual Categories. Movies that have been shown at the theaters or
direct-to-video movies use the Movie Rating System (MPAA) only.
Parental
Parental Control
Off
Unrated Program Block
Parental Guide
Off
1. Press CH+/- to select Parental.
2. Press the VOL+ button to enter Parental submenu.
MPAA Rating
The TV is set up with the initial password 0-0-0-0. If the password in the
Lock Set menu is changed, and the security default password is 9-4-4-3
The password here will also change. (Password See p27 )
24 Plasma TV
Download from Www.Somanuals.com. All Manuals Search And Download.
Continue
Parental
Ratings for Movies previously shown in theaters:
Movie Ratings :
Parental
Parental Control
NR
G
(Permits all programs)
(General audience)
Off
Off
Unrated Program Block
Parental Guide
PG
PG-13
R
(Parental guidance suggested)
(Parents strongly cautioned)
(Restricted)
MPAARating
NC-17
X
(No one 17 and under admitted)
(Adult only)
If you set PG-13 : G and PG movies will be available , PG-13, R,
NC-17 and X will be blocked.
Parental Guide
Rating ALL
V
V
S
L
D
Ratings for Television programs including made-for-TV movies :
TV-Y
V
V
V
V
V
V
TV-Y 7
TV-G
TV-Y
(All children)
TV-Y7
TV-G
(Children 7 years older)
(General audience)
TV-P G
TV-1 4
TV-M A
V
V
V
V
V
V
V
V
V
V
V
TV-PG
TV-14
TV-MA
(Parental guidance suggested)
(Parents strongly cautioned)
(Mature audience only)
MPAARating
TV Rating Children:
ALL (Age)
G
V
V
V
V
V
V
PG
PG-13
R
(applies to TV-Y, TV-Y7)
(applies to TV-Y7)
FV (Fantasy Violence)
NC17
X
TV Rating General:
ALL (Age)
(applies to TV-G, TV-PG, TV-14, TV-MA)
(applies to TV-PG, TV-14)
D (Dialogue - sexual dialogue)
L (Language - adult language)
S (Sex -sexual situations)
V (Violence)
(applies to TV-PG, TV-14, TV-MA)
(appliesto TV-PG, TV-14, TV-MA)
(applies to TV-PG, TV-14, TV-MA)
Note: If some option is locked, the options of the same level will also be locked and the screen display Lock .
TV Rating Limits and Movie Rating Limits can only be used when Parental Control is set to Custom.
Owner s Manual 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Time Setup
If Off-time or On-time isintended inAV1/S-Video/YPbPr/YCbCr/VGA, follow theinstructions as below:
Clock Setting
The clock will only work if the TV set is turned on or in standby.
Clock
12:30
20:30
17:30
000
When the set is disconnect from the power supply or is turned off by
the main power on the rear panel, the clock loses power and will need
to be reset when the power is reconnected.
Off Time
On Time
On CH
1
Press MENU buttonand then VOL+/-button to selectthe TIME menu.
Press CH+/- button to select "Clock",press VOL +/- button to select hour
or minute position, then press the digital buttons to set the value of hour or minute.
2
Remind Time
Remind CH
19:00
000
A
B
C
Note:
If Clock isset, the timeyou set forOff Time and OnTime willbe a point
of time, Otherwise, if Clock isnot set, thetime you setfor Off Time and
On Timewill be aperiod of time, And itwill account timewhen you set
automatically .
Off/On Time
Using on/off time function, the TV set can automatically turn on to a preset channel or shut down at a preset time.
1 Press CH+/- buttonto select "OnTime", press VOL+/-button toselect hour or minute position; then press the digit
buttons to setthe value of both hours or minutes.
2
3
Press CH+/- button to select "On CH", then press the digit buttons to select your desired channel.
Repeat step 1-2 to set "Off Time".
Indication will appear on the screen 1 minute prior to
the shut down of the set
Note:
The Sleep Time and Off Time can notbe set assimultaneously .
If both timeare set , the later setupwill be inoperation.
Off Time
Remind Time/Remind CH
1 Press MENU and then VOL+/- button to call up the TIME menu on the screen.
2 Press CH+/- buttonto select "Remind Time", then press VOL+/- button to select hour or minute position;
then press the digit buttons to set the value of hour or minute.
3 Press CH+/- buttonto move thecursor to "Remind CH".
Then press the digit buttons to set the desired channel.
26 Plasma TV
Download from Www.Somanuals.com. All Manuals Search And Download.
Lock Menu Options
- The TV has the function of security default lock. Password needs to be entered when the program lock mode is to be set.
Lock Setup
Press LOCK button on remote control, Password will appear on the screen. If password is correctly entered, the LOCK menu
will be displayed. If the password is not correctly entered, you will be required to reenter the password and the cursor will
remain onscreen.
Press EXIT to exit the window. If the preset OSD time is exceeded, the menu will disappear automatically.
Lock Set
PassWord
Tuning Lock
Preset CH
CH Num
Off
Off
Change Password
1
Source Lock
Child Lock
Max Volume
UnLock
To change the default password: Press CH+/- button and select
Password. Press VOL+/- or ENTER button, the screen will display
Old Pw.----, which will remain on the screen if a wrong password
is entered. If correct password is entered, the screen will
Off
100
display New Pw.----. Enter the new password, and the screen will display
Confirm----. If the same password is entered correctly twice, the old
password will be changed. If the same password is not correctly entered
twice, the screen will display New Pw.----, and you will be required to start over.
Note:
The initial password is 0000, and the security default password is 9443. If Unlock isactivated, the password
setup cannot be changed.
Tuning Lock
Press CH+/- to select Tuning Lock and VOL+/- to set it as On/Off. (To set as On, some operation such as search will be
no available. When to enter the SYS. menu, the "Tuner Lock" will appear on the screen). If you want to operate SYS. menu,
you need to enter the Lock menu to set Tuning Lock as Off or operate UnLock item.
Preset CH
Preset CH is used for setting up start signal source. Press CH+/- button to select Preset CH. Press VOL+/-
button, sources can be swapped in TV/AV1/SVideo/YPbPr/VGA/DVI/Off mode. After setup, the selected source will be
displayed when the TV is turned on again.
Owner s Manual 27
Download from Www.Somanuals.com. All Manuals Search And Download.
CH Num(channel number)
Channel number isused for settingup a presetchannel at poweron. Press CH+/-button to selectCH Num. PressVOL+/- button,
to select channelnumber.(The itemis not availableexcept with aTV signal.)
Source Lock
Source Lock is used to hinder external input modes, such as AV, S -Video and VGA. Press CH+/-button to select
the option, and press VOL+/- button to display Source Lock menu.
Press CH+/- button to select desired option. Press VOL+/- button to set up the
mode of Source Lock. If a Source Lock is set on, the screen will display
Source Lock
a blue background with the mute mode activated, and LOCK will be shown on the
screen. In Lock On mode, when screen is blank, icon Lock will be always
AV1
Off
Off
Off
Off
Off
displayed on the screen. If lock mode is to be verified, enter Source Lock sub
menu and set relative mode off or select Unlock mode in the Lock Menu.
S-Video
YPbPr/YCbCr
VGA
DVI
Child Lock
Press CH+/- button to select Child Lock. Press VOL+/- button to set On or Off mode. If lock on mode is set,
if buttons on TV are pressed, the screen will display Child Lock. This display can be turned off by pressing the EXIT
button, or 5 seconds later after the latest key press, the display will disappear automatically.
The Child Lock mode can be stopped by entering Lock Set menu to set Child Lock OFF or active Unlock.
Max Volume
Press CH+/- button to select Max Volume. Press VOL+/- button for adjustment between 0 100. If a certain value is set,
when volume is being adjusted, the sound value cannot exceed maximum the volume value. If current volume is over
Max Volume, when Lock Set menu is set, current volume will become set maximum volume. If current
volume is below maximum volume, customer set volume will be applied.
Unlock
Press CH+/- buttonto select Unlockmode.
Press VOL+/- buttonto unlock allset modes, willset all lockoptions to OFF, and themaximum volume returnsto 100.
28 Plasma TV
Download from Www.Somanuals.com. All Manuals Search And Download.
- RGB (PC)mode only; Thisfunction doesn`t work in RGB-DTV mode.
- Automaticallyadjusts picture positionand minimizes imageshaking.
- Afteradjustment, if theimage is stillnot correct, yourTV may needfurther adjustment.
- The Auto sync is not active inDVI mode.
1. Press MENU button and then use VOL+/- buttonto select theADJ. Menu.
Display Mode
Adjust
Full screen
2. Press CH+/-button to select Auto Sync.
3. Press VOL+/-button to runAuto Sync.
When Auto Sync has finished, a better quality image should be shown on screen.
RGB
Reset
If the position of the image is still not correct, tryAuto adjustment again.
Auto Sync.
Color Temper.
Black Stretch
Note: Use Resetinstead ofAuto sync in480P,720P,1080i.
Standard
On
4. In RGB(PC) mode, if the image needs to be adjusted more after using Auto
Sync, you cantry AutoSync again.
A
B
C
- Caution: Ifa 4:3 orone to onefixed image ison the screenfor a longtime, it mayremain visible. This is calledburn-in.
- Set everyaspect ratio forVideo, Component 480i sources.
- Use 4:3, or 16:9 forother RGB-PC andDVI-PC sources.
- Horizon isnot available forComponent (480p,720p,1080i), DTV(480p,720p,1080i) sources.
Press the ARC button repeatedly toselect the desiredpicture format.
4:3 mode
Choose 4:3 mode when you wantto view apicture with anoriginal 4:3 aspectratio, with blackbars appearing atboth the
left and rightsides.
Full screen( correspondwith 16:9)
Choose Full screen when you wantto adjust thepicture horizontally, in alinear proportion tofill the entirescreen.
Vertical Zoom
Choose Vertical Zoomwhen you wantto adjust thepicture the picturevertically, that is withoutany back bars.
Note:
The setting ofaspect ratio isrespective of eachdifferent signal source , thatmeans different aspect ratios canbe saved
in each different source
- This function works inthe following modes:
RGB-PC, RGB-DTV (480p,720p,1080i), DVI-DTV (480p,720p,1080i), COMPONENT(480p,720p,1080i).
1. Press MENUbutton and thenuse VOL+/- buttonto select theADJ. Menu.
2. Press CH+/-button to selectAdjust.
3. Press VOL+/-button or enterbutton to enterthe sub menu.
4. Press CH+/-button to selectone option andthen press VOL+/-to adjust.
5. Press MENUor EXIT to exit it.
Owner s Manual 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Check whether theTV is turned on fromboth front buttonand
the back switch.
No picture &
No sound
Is the powercord inserted intowall power outlet?
Test the wallpower outlet, pluganother product`s powercord into the
outlet where theTV`s power cord was pluggedin.
Press the VOL+button.
Picture OK &
No sound
Is the soundmuted? Press MUTEbutton.
Check to see if there is any object between the TV and the remote
control causing obstruction.
Are batteries installed with correct polarity (+ to +, - to -)?(Refer to p.8)
Correct remote operating mode set: VCR, etc.?
Install new batteries. (Refer to p.8)
The remote control
doesn`s work
Picture appears slowly
after switching on
This is normal, the image is muted during the display startup process. Please
contact your service center, if the picture has not appeared after five minutes.
Select Color Temperature in theADJ menu and pressthe VOL+/- button.
Keep a sufficient distance betweenthe TV and the VCR.
No or poor color
or poor picture
Activate anyfunction to restorethe brightness ofthe picture.
Horizontal/vertical bars
or picture shaking
Check for localinterference such asan electrical applianceor power tool.
No output from one of
the speakers
Adjust Balance in the SOU. menu. (Refer top.21)
A change in ambient humidity or temperature may result in an unusual noise
when the plasma display is turned on or off and does not indicate a fault with it..
Unusual sound from
inside the TV
30 Plasma TV
Download from Www.Somanuals.com. All Manuals Search And Download.
- Early malfunctionscan be prevented. Careful and regularcleaning can extendthe amount ofrunning time youwill have your
new TV. Be sureto turn thepower off and unplug thepower cord beforeyou begin anycleaning.
1. Here`s agreat way tokeep the dustoff your screen for awhile. Wet a soft clothin a mixtureof lukewarm waterand
a little fabricsoftener or dishwashing detergent. Wring the clothuntil it`s almostdry, and then useit to wipethe screen.
2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.
To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
Please be sure not to use a wet cloth.
If you expect to leave your TV dormant for an extended period of time (such as a vacation), unplug
the power cord to protect against possible damage from lightning or power surges.
The PDP Manufacturing Process: Minute colored /bright/dark dots may present on the screen.
The Plasma Panel(the display deviceof this product)is composed of0.9 to 2.2million cells. A fewcell defects maynormally
occur in thePDP manufacturing process or appearover time. Minute, non-conforming pixels visibleon the screendo not
indicate a defectivepanel, and fallwithin acceptable operationalstandards. This is indicative ofPDP technology and is nota
sufficient cause for the setto be exchangedor returned. Ourproduction technology willminimize these celldefects as best
possible during themanufacture and operationof this product.
Owner s Manual 31
Download from Www.Somanuals.com. All Manuals Search And Download.
PH-4210D
MODEL
Dimensen(WXHXD)
Unit::inches/mm
41.5 "x25.7 "x3.4 "/1055x654x86
(main compoment)
51.6 "x28.7 "x10.6 "/1310x730x270
(Stand and speakerincluded)
Weight (pounds / kg)
Resolution
66.2/30
1024x768(Dot)
Power requirement
Color System
~100-240 Volts , 50/60Hz
Operating Temperature Range
Operating Humidity Range
Maximum Elevation
Impedance
8
Input
consumption
2x7W
Speakers
Size(WxHxD)
(inches/mm)
4.3x21.9x2.4/110x556x62
Weight
(pounds/kg)
2x5.5/2x2.5
The specifications shown above may be changed without notice for quality improvement.
32 Plasma TV
Download from Www.Somanuals.com. All Manuals Search And Download.
PWW LIMITED WARRANTY FOR PDP/LCD TELEVISION PRODUCTS
PWW warrants this product to be free from manufacturing defects in material and workmanship
under normal use for the period indicated on the warranty card.
What PWW will do:
Pay an authorized PWW Service Center the labor charges to repair your television.
Pay an authorized PWW Service Center for the new, or at our option, refurbished- replacement parts
required to repair your television.
How to obtain service:
Call the PWW Customer Support line documented on the warranty card, or visit www.pwwservice.com
to locate the nearest authorized PWW Service Center.
For televisions with screen sizes 30" or less you will be requested to bring your unit in to the authorized
service center and pick up when repairs are complete.
For televisions with screen sizes 32" and above you may request home service from an authorized
PWW Service Center provided that your television is located within the geographic territory covered by
an authorized PWW Service Center. If in-home service is not available in your area, you must take
your television to the Service Center location at your own expense, or pay for the cost that the
Service Center may charge to transport your television to and from your home.
Proof of purchase in the form of a bill of sale or receipted invoice, which is evidence that the product is
within the warranty period, must be presented to obtain warranty service.
This warranty does not cover:
Removing LCD / PDP sets from custom wall mounts or cabinetry. All in-home service requests for
LCD/PDP televisions requires that the unit be dismounted and accessible for the service technician
prior to their arrival. Technicians are not responsible for remounting the LCD/PDP set upon completion
of repairs. All costs and fees associated with mounting and unmounting units will be the sole
responsibility of the customer.
Physical or cosmetic damages.
Ordinary adjustments as outlined in the owners manual that can be performed by the customer.
Damage to equipment not properly connected to the product.
Any cost incurred in shipping the product for repair.
Signal reception problems caused by external antenna, cable systems or interference.
Incompatibility due to a change in TV/CATV broadcast systems after the product was sold.
Batteries.
Images burnt on to the screen.
Initial installation and related adjustments.
Power surge and / or lightning protection.
This warranty is void:
If the original proof of purchase cannot be supplied.
Damaged through misuse, negligence or abuse.
Modified or repaired by anyone other than authorized PWW service center.
Damaged because it is improperly connected to any other equipment.
Used in a commercial application or rental.
PWW Service Corp is not liable for any claim made by a third party or made by you for a third party.
This warranty is not transferable and only applies to the original purchase, and only in the original country of
purchase. Any implied warranties, including the warranty of merchantability, are limited in duration to the
period of this expressed warranty and no warranty whether expressed or implied shall apply to the product
thereafter. Under no circumstance shall PWW be liable for any loss or consequential damage arising out of
the use of this product. This warranty gives specific legal right. However, you may have other rights that may
vary from state/province to state/province. Some state/province do not allow limitations on implied
warranties or exclusions of consequential damage. Therefore these restrictions may not apply to you.
product.
Owner s Manual 33
Download from Www.Somanuals.com. All Manuals Search And Download.
V0.1
0090506987A
Download from Www.Somanuals.com. All Manuals Search And Download.
|