Haier Flat Panel Television LE42H330 User Manual

OWNER’S MANUAL  
LE42H330  
LE46H330  
LE55H330  
LD42K3  
LED-LCD TELEVISION  
Please READ this manual carefully before  
operating your TV, and retain it for future  
reference.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Warning  
Warning  
WARNING  
RISK ELECTRIC SHOCK  
DO NOT OPEN  
!
WARNING:  
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS  
INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.  
*To avoid electric hazards, it is strongly suggested that the back cover not be opened, as there is no any  
accessory inside the casing.  
*lf necessary, please contact authorized after-sales services.  
*A lighting flash mark in a triangle: A potentially hazardous situation, which, if not avoided, could result in  
serious injury by high voltage.  
*An exclamation mark in a triangle: Major part or accessory of which technical specifications must be followed if  
it is to be replaced.  
WARNING: To avoid fire or electric hazards, never place your television receiver in an area with heavy  
moisture. Attention should be paid to avoid accidental scratches or impacts onto the screen.  
CAUTION:  
CAUTION:  
Please read this manual carefully before using your television and keep this manual in a  
good place for future reference.  
To achieve the best performance of your television, read this User’s Manual carefully and  
properly store it for future reference.  
Information of screen displays and figures in the User’s Manual may vary due to technical  
innovations.  
Unauthorized disassembly of this product is prohibited.  
LED -LCD television Owner’s Manual  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safety Instructions  
Important Safety Instructions  
4
LED -LCD television Owner’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safety Instructions  
LED -LCD television Owner’s Manual  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Panel Control  
Introduction  
- This is a simplified representation of front panel.  
- Here shown may be somewhat different from your TV.  
Panel Control  
LD42K3  
LE42H330/LE46H330/LE55H330  
Press this key to open/close signal source  
options menu.  
TV/AV  
1
Press to adjust the volume. In the MENU screen,  
VOL +/-  
POWER  
2
3
these buttons serve as right/left buttons.  
Press to turn on and off the TV.  
Press to scan through channels. To scan quickly  
through channels, press and hold down either  
+/- . In the MENU screen, these buttons serve  
as up/down buttons.  
Menu display. Press to access the on-screen  
menu display.  
CH +/-  
MENU  
4
5
6
LED -LCD television Owner’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Panel Control  
Remote Control  
Battery loading  
1. Slide open the cover of the battery compartment on  
the back of the remote controller.  
2. Load two 7# (AAA) alkaline batteries in the  
compartment, (plus and minus poles to respective mark)  
3. Replace the cover of the battery compartment.  
Precautions  
As strong light may interfere the signals, change your  
position to operate the remote controller if the television  
cannot be turned on or off as you expect.  
Make sure that two AAA alkaline batteries are loaded.  
The batteries must be of the same type. The batteries  
must be located properly. The batteries are not  
rechargeable.  
Keep the remote controller away from heat source or  
humid area to ensure effective performance of the  
remote controller.  
Make sure that there is no obstacle between the remote  
controller and television set.  
8
LED -LCD television Owner’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connection Options  
Connection Options  
Back panel connections  
LD42K3  
LE42H330/LE46H330/LE55H330  
Connect a video cable from a computer to this  
jack.  
PC/DVI Audio Connect the audio L/R cables from a computer  
Connect cable pr antenna signal to the TV, either  
directly or through your cable box.  
PC Video In  
1
2
3
4
5
6
8
ANT In  
.
SPDIF  
W/A  
Digital Audio Optical output.  
9
0
In  
to this jack.  
For the smart comtroller.  
Component  
Video In  
Connect a component video device to these  
jacks.  
Connect a USB flash drive to view videos,images  
USB jack  
LAN  
A
B
C
D
or listen music  
.
Component  
Audio In  
Connect the audio L/R cables from the  
component video signal source to these jacks.  
Connect to the internet (No available).  
Connect the S-VIDEO cable from an external signal  
source to this jack.  
Connect a HDMI device to receive digital audio  
and uncompressed digital video.  
S-VIDEO IN  
Headphone  
HDMI1-3 In  
AV OUT  
Headphone audio output terminal  
.
Connect the audio L/R and video cables to your  
other video equipment.  
AV1 In  
Connect the video signal from a video device.  
7
LED -LCD television Owner’s Manual  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control Function  
Remote Control Function  
- The remote control cannot be operated unless the batteries are properly loaded.  
- When using the remote control, aim it at the remote control sensor on the TV.  
Function introduction  
Press this key to start TV from standby mode, press it again to return to standby  
mode.  
Press this key for quick switching of streaming media.  
Refer to the Functional Description on Page 20.  
Press this key to open/close signal source options menu.  
Press this key for quick switching of MO-Car.  
1
POWER  
2
3
4
5
USB  
H. LOCK  
SOURCE  
DSMB  
Press this key to freeze the image. Press it again to return to normal screen. (Note:  
Do not display a still picture for a long time to prevent the screen from burns.).  
Press this key to select the screen display proportion.  
Press this key to mute the sound, press it again to activate the sound. The sound  
may be activated by turning the TV on again or increasing the volume.  
These keys are used to select a channel.  
6
7
8
9
STILL  
ARC  
MUTE  
0-9  
0
A
Press this key to return to the previous TV program(only work in the TV mode).  
Used to adjust the volume when the screen menu is closed.  
Used to select a TV channel when the screen options menu is closed, specifically,  
press P˜ to decrease the channel and press Pto increase the channel..  
Press this key continuously to select the sound mode.  
Q. VIEW  
VOL+ /-  
B
CH+/-  
C
D
E
Sound Mode  
Picture Mode  
TV.MENU  
Press this key continuously to select the picture mode.  
Press this key to display or exit the main menu.  
Press this key to display the Special Function Menu (it functions when special  
modules are inserted).  
F
G
D.MENU  
THUMBSTICK (Up/ Allows you to navigate the on-screen menus and adjust the system settings to  
Down/Left/Right) your preference.  
H
I
OK  
EXIT  
Press this key to confirm the selection.  
Clears all on-screen displays and returns to TV viewing from any menu.  
Control the USB System.  
Backward  
Forward  
Play/Pause BACK: Back REC: no available  
J
K
USB  
ZOOM: Press to magnify/minify an image D.CALL: Press to display program  
information.  
Display on/off.  
TV.CALL  
L
M
N
O
P
Q
R
S
T
U
No available.  
TIMESHIFT  
VOD  
AUDIO  
PAGE+  
GUIDE  
TV/FM  
INFO  
PAGE-  
CH.LIST  
FAV  
No available.  
No available.  
No available.  
No available.  
No available.  
No available.  
No available.  
No available.  
Press this key to display the favorite program list menu.  
V
No available.  
STOCK  
W
X
Y
Z
[
\
Displaying the sleep time.  
No available.  
No available.  
No available.  
No available.  
SLEEP  
INTERACTION  
Fn  
DDS  
BUSINESS  
GAME  
No available.  
LED -LCD television Owner’s Manual  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
External Equipment Connections  
External Equipment Connections  
Antenna Connection  
- Antenna or Cable Service without a Cable Box Connections.  
- For optimum picture quality, adjust antenna direction if needed.  
Note:  
* It is recommended that you'd better use 757 coaxial cable to remove  
the disturbance caused by airwave.  
* Don't bind antenna cable and electric wire together.  
To improve picture quality in a poor signal area,  
purchase and install a signal amplifier.  
If the antenna needs to be split for two Tv’s, install a  
"2-WaySignal Splitter" in the connections.  
AT.  
If the antenna is not installed properly, contact your  
dealer for assistance.  
Note  
All cables shown are not included with the TV.  
10 LED -LCD television Owner’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
External Equipment Connections  
select the source, press the OK button to confirm.  
Choose Your Connection  
There are several ways to connect your television,  
depending on the components you want to connect  
and the quality of the signal you want to achieve. The  
following are examples of someways to connect your TV.  
Take LE42H330 as an example, Choose the connection  
which is best for you.  
External AV Source Setup  
How to connect  
Connect the audio and video cables from the  
external equipment’s output jacks to the TV input  
jacks, as shown in the figure.  
VCR Connection  
To avoid picture noise (interference), leave an adequate  
distance between the VCR and TV.  
When connecting the TV to external equipment,  
match the jack colors (Video = yellow, Audio Left =  
white, and Audio Right = red).  
How to use  
Connection Option 1  
A
Select the input source with using the SOURCE  
button on the remote control.  
Set VCR output switch to channel 3 or 4 and then tune  
the TV to the same channel number.  
B
C
D
Press button to select the desired source.  
/
ꢂꢃ  
Connection Option 2  
Press OK button to confirm.  
A
Connect the audio and video cables from the VCR’s  
output jacks to the TV input jacks, as shown in the  
figure. When connecting the TV to VCR, match the  
jack colors (Video = yellow, Audio Left = white, and  
Audio Right = red).  
Operate the corresponding external equipment.  
Connecting a DVD player  
B
C
Insert a video tape into the VCR and press PLAY on  
the VCR. (Refer to the VCR owner’s manual.)  
How to connect  
A
Connect the DVD video outputs (Y, Pb/Cb, Pr/Cr)  
to the COMPONENT (Y, Pb/Cb, Pr/Cr) input jacks on  
the TV and connect the DVD audio outputs to the  
Select the input source with using the SOURCE button  
on the remote control, and then press  
/
ꢂꢃ  
button to  
LED -LCD television Owner’s Manual 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
External Equipment Connections  
AUDIO jacks on the TVas shown in the figure.  
C
Press Play button on external equipment for  
program play.  
/
How to use  
A
B
Turn on the DVD player, insert a DVD.  
Use the SOURCE button on the remote control,and  
PC Setup  
then press  
mode, press the OK button to confirm.  
/
button to to select COMPONENT  
ꢂꢃ  
How to connect  
C
D
Press Play button on external equipment for  
program play.  
A
B
Use the TV’s PC IN port for video connections.  
Refer to the DVD player’s manual for operating  
instructions.  
Then, make the corresponding audio connection. If  
using a sound card, adjust the PC sound as required.  
HDMI or DVI Setup  
How to use  
A
B
Turn on the PC and the TV.  
To watch digitally broadcast programs, purchase and  
connect a digital set-top box.  
Turn on the display by pressing the POWER button  
on the TV’s remote control.  
How to connect  
C
D
Use SOURCE on the remote control to select PC source.  
Use the TV’s COMPONENT (Y, Pb/Cb, Pr/Cr) INPUT  
jacks, VGA or HDMI port for video connections,  
depending on your set-top box connections  
available. Then, make the corresponding audio  
connections.  
Check the image on your TV. There may be noise  
associated with the resolution, vertical pattern,  
contrast or brightness in PC mode. If noise is  
present, change the PC mode to another resolution,  
change the refresh rate to another rate or adjust the  
brightness and contrast on the menu until the picture  
is clear. If the refresh rate of the PC graphic card  
can not be changed, change the PC graphic card or  
consult the manufacturer of the PC graphic card.  
How to use  
A
Turn on the digital set-top box.  
(Refer to the owner’s manual for the digital set-top box.)  
B
Use SOURCE on the remote contralto select PC or  
HDMI (Y, Pb/Cb, Pr/Cr) mode.  
12 LED -LCD television Owner’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
External Equipment Connections  
Note  
Component, PC, HDMI input sources cannot be  
used for Monitor out.  
When connecting with external audio equipments,  
such as amplifiers or speakers, please turn the TV  
speakers off.  
Power source  
TO USE AC POWER SOURCE  
Use the AC polarized line cord provided for operation on  
AC. Insert the AC cord plug into a standard polarized AC  
outlet.  
Note  
Avoid keeping a fixed image on the TV’s screen for  
along period of Time. The fixed image may become  
permanently imprinted on the screen.  
The synchronization input form for Horizontal and  
Vertical frequencies is separate.  
To obtain the best picture, do not play the USB,  
YPbPr, HDMI or PC source at the same time.  
Monitor Out Setup  
The TV has a special signal output capability which  
allows you to hook up a second TV or monitor.  
Note  
Never connect the AC line cord plug to other than  
the specified voltage. Use the attached power cord  
only.  
Connect the second TV or monitor to the TV’s AV OUT  
by the tie line. See the Operating Manual of the second  
TV or monitor for further details regarding that device’s  
input settings.  
If the polarized AC cord does not fit into a non  
polarized AC outlet, do not attempt to file or cut  
the blade. It is the user’s responsibility to have an  
electrician replace the obsolete outlet.  
If you cause a static discharge when touching the  
unit and the unit fails to function, simply unplug  
the unit from the AC outlet and plug it back in. The  
unit should return to normal operation. Polarized  
AC Cord Plug.  
LED -LCD television Owner’s Manual 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Receiving and Playing Operations  
Choose the Input source  
Basic Receiving and  
Change the picture source so you can watch your TV,  
VCR, Cable , or any other devices that are connected to  
your TV.  
Playing Operations  
Playing Operations  
A
B
Press SOURCE button to enter the Input Source  
menu and then use button to select the  
desired items (ATV/DTV, AV1, AV2, Component, PC,  
HDMI1, HDMI2, HDMI3).  
/
ꢂꢃ  
Switching ON/OFF the TV set  
In the manual, the OSD (on screen display) may be  
different from your TV’s because it is just an example to  
help you with the TV operation.  
Press OK button to confirm .  
Switching ON/OFF the TV set  
Picture Menu  
A
First, connect power cord correctly and the power  
indicator will light.  
The TV menu gives you an overview of the menus you  
can select.  
B
C
Press POWER on the remote control again.  
If you want to exchange to standing by status,  
Note  
please press down POWER on the remote control  
Depending on the input signal, one or more menu  
items may not be selectable.  
D
Disconnect the power supply or unplug the  
television if it is intended to completely cease the  
television performance.  
How to select picture mode  
Choose the Menu Language  
The picture mode provides the pre-defined images  
settings: Standard, Mild, User, Dynamic and EyeGuard  
.
When you adjust your set for the first time, you must  
select the language which will be used for displaying  
menus and indications.  
press  
picture mode repeatly. Standard, Mild, User, Dynamic  
and EyeGuard  
button on the remote control to select the  
A
B
Press MENU and  
/
to select Function menu.  
.
Press  
/
button to select language option and  
ꢂꢃ  
then press OK to confirm.  
C
D
Select a particular language by pressing  
repeatedly.  
/
ꢂꢃ  
How to customize your own picture status  
When you satisfied with your choice, press MENU to  
return to normal viewing.  
A
Press MENU button and then use  
select Picture menu.  
/
button to  
Back light LED Four...  
B
C
Press  
/
button to select the desired items.,  
ꢂꢃ  
Surround  
press OK to enter its submenu.  
Prog...  
DTV Manu...  
Intelligent  
Mode  
Net  
Upgrade  
Press button to adjust the setting.  
/
ꢂꢃ  
Chinese  
14 LED -LCD television Owner’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Receiving and Playing Operations  
range of 2500K~15000K from warm color to cold  
color, afterwards press  
benchmark is selected for adjustment, the original  
adjustment data will be automatically cleared.  
/
to adjust; if a different  
LED  
Four_DIM  
Back light  
Reset  
Contrast  
Brightness Color  
Sharpness Tint  
Back light  
LED  
Four_DIM  
Palette  
Prog...  
DTV Manu.  
Picture  
Intelligent  
Mode  
Cool2  
+50  
Sound
Cool1
Channel  
Standard  
0
Warm1  
Function  
-50  
Warm2  
Adjust  
User  
Timer  
Contrast  
%$&.  
029(  
2.  
MENU  
OK  
This will adjust the intensity of bright parts in the  
picture but keep the dark parts unchanged.  
Reset  
Brightness  
Press  
/
ꢂꢃ  
to select OK or Cancel..  
This will adjust the light output of the complete  
picture, which will mainly affect the darker areas of  
the picture.  
Sound menu  
Color  
This will adjust the saturation level of the colors to suit  
your personal preference.  
How to select sound mode  
A
Press MENU button and then use  
select Sound menu.  
/
button to  
Sharpness  
This will adjust the sharpness of fine details in the  
picture.  
B
Press OK button and then use  
/
ꢂꢃ  
button to  
select Digital tone Mode.  
Note  
The picture options can only be adjusted in the  
Back light LED Four.  
User mode. The other picture modes are preset.  
Tint  
Prog...  
Allows you to select the color mix (Tint) of the picture.  
DTV Manu.  
Net  
Upgrade  
Intelligent  
Mode  
Back light  
Press /  
ꢂꢃ  
button to adjust the Backlight.  
LED Four_DIM  
Select the LED Fore-drive_DIM Demo or LED Fore-  
drive_DIM Calibration, Press OK to set.(It's not  
availabe for LD42K3)  
C
Press  
/
button to select the option Standard,  
Music, Movie and User.  
You can also press S.MODE button on the remote  
control repeatly to select the sound mode you  
want. Standard, Music, Movie and User.  
Palette:  
Press  
/
to select the Palette option, and then  
ꢂꢃ  
press OK to enter its submenu, and finally press  
/
to select a toner pattern from six patterns  
(Cool2, Cool1, Standard, Warm1, Warm2, User) to your  
color preference. Normally, the Standard mode is  
selected.  
How to Customize your own sound  
status  
If the User mode is selected, press  
/
to enter  
ꢂꢃ  
the palette menu, (as shown in the below figure),  
and then press to select a benchmark in the  
A
Press MENU button and then use  
select Sound menu.  
/
button to  
/
ꢂꢃ  
LED -LCD television Owner’s Manual 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Receiving and Playing Operations  
B
C
Press  
/
ꢂꢃ  
button to select the desired items,  
Return to factory default settings.  
press OK to enter its submenu.  
Press  
/
ꢂꢃ  
button to adjust the setting.  
Channel menu  
Display channel menu by pressing SOURCE button then  
Volume  
use  
item.  
/
ꢂꢃ  
button to select the source of ATV or DTV  
Press  
/
ꢂꢃ  
to adjust the volume of TV set.  
Balance  
A
B
Press MENU button and then use  
select Channel menu.  
/
button to  
This will adjust the output of the right and left  
speakers to obtain the best stereo reproduction for  
your listening position.  
Press button to select the desired items,  
/
ꢂꢃ  
press OK to enter its submenu.  
The intermediate value is 0. When indication value of  
balance is greater than 0,sound of the right is stronger  
than the left. when indication value of balance is less  
than 0,the left sound is stronger than the right sound.  
Back light LED Four...  
Prog...  
DTV Manu...  
Digital tone  
This select the modes for sound reproduction dependent  
on the broadcast signals or signals from external inputs  
received.  
Intelligent  
Mode  
Net  
Upgrade  
Select the mode of sound (User/Standard/Music/Movie).  
If the User mode is selected, press  
a benchmark in the range of 50~15K from bass to  
/
to select  
ꢂꢃ  
treble, afterwards press to adjust, if a different  
/
benchmark is selected for adjustment, the original  
adjustment data will be automatically cleared.  
Programme Edit  
Back light LED Four..  
You can add a label to a channel to make it easier to find.  
A
Press MENU button and then use  
select Channel menu.  
/
button to  
Manual Search  
option, and finally  
to select the Search  
/to start manual search. Upon finding a  
Press  
press  
/
program, the search will automatically stop, and the  
program will be stored onto the current channel.  
Surroud  
You may stop the search by pressing OK or MENU  
.
The surround sound feature expands the audio  
listening field wider and deeper to create exceptional  
sound quality from the TV’s speakers.  
Fine Tune  
Press  
then press  
/
to select the Fine Tune option, and  
/to start UP or DOWN fine tuning  
AVL (Automatic Volume Limit)  
until obtaining a relatively good picture effect. The  
fine tuning function is for the purpose of improving  
picture effect through fine tuning when that of a  
certain program is not good enough. Normally, the  
optimal picture effect can be obtained without fine  
tuning when watching TV programs, and fine tuning  
is to meet the need of adjusting a certain program.  
This will reduces the differences in volume level  
among broadcasters.  
MAXX Bass  
To adjust the super bass. Press  
bass off, low , high or Medium.  
/
ꢂꢃ  
to select super  
Reset  
16 LED -LCD television Owner’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Receiving and Playing Operations  
screen.  
Back light LED Four...  
Intelligent  
Mode  
Net  
Upgrade  
Color system  
All channels now available will be automatically preset in  
order .After the search has finished, the first program  
Press  
and then press  
system.  
The TV is designed with three systems for your  
choice, i.e. Auto, PAL , SECAM and NTSC. Generally,  
the system is set as Auto and it is not necessary to  
make an adjustment. The system is normally set as  
Auto during auto search.  
/
to select the Color Systems option,  
to select correct color  
/ꢃ  
number will display on the screen. This search  
automatically adds only the active channels in your area  
to the TV's memory.  
It deletes any channels on which there is no broadcast or  
a poor signal.  
Sound system  
The channels found are automatically saved.  
The TV is designed with four systems for your  
choice, i.e. DK, M, BG and I. Generally, it is not  
necessary to adjust the system. The system is  
normally set as BG during auto search.  
Prog. Exchange  
A
Press MENU on the remote control unit or MENU on  
the TV’s front panel to display main menu, and then  
Skip  
press  
/
to select Channel menu.  
When the skip is set ON, the channel will be  
skipped when pressing CH ˜ or CH and only can  
be selected by pressing 0-9 numerical keys.  
B
C
Press  
to select the Prog. Exchange option,  
/ꢃ  
and then press OK to enter its submenu.  
If you want to recover the skipped channel  
Press to select the To Channel option, and  
then press  
/
/
ꢂꢃ  
to set the found to be exchanged to.  
1. Use Direct-digit Choosing button to select the  
number of the channel to be recovered.  
2. Do the above steps again.  
3. Press  
to set Skip as Off.  
/ꢃ  
Auto Tuning  
A
B
C
Press MENU button and then use  
select Channel menu.  
/
button to  
D
After adjusting the current channel and the found to  
be exchanged to, press to move the cursor  
to the Exchange option, and then press OK to start  
exchange and exchange the program on current  
channel to the channel you set for exchange.  
Press  
button to select Auto Tuning, then  
/ꢃ  
/
press OK to enter its submenu.  
Press button to select OK, press OK button  
/
ꢂꢃ  
to start to scan. Press MENU button to return to the  
previous menu, press EXIT button to EXIT the menu  
LED -LCD television Owner’s Manual 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Receiving and Playing Operations  
MEMC  
Function Menu  
Press  
/
to set ON, Demo1,Demo2 or OFF, the  
ꢂꢃ  
moving picture will be better when MEMC is on  
function.  
Function Menu Set  
DSM  
Press  
DEMO3.  
/
ꢂꢃ  
to select DEMO OFF, DEMO1,DEMO2,  
A
Press MENU on the remote control unit or MENU  
on the TV’s front panel to display the main menu, and  
Intelligent Mode  
Press  
then press  
/
to select the Function menu.  
/
to set ON /OFF/Demo, if you select ON,  
ꢂꢃ  
B
Press  
/
to select the option to be adjusted,  
ꢂꢃ  
the TV set will be in the intelligent mode, if there is  
no one in front of the TV for about 20 minutes, the  
TV power saving state, 10 minutes latter, the TV set  
automatically stand by, When people return in front  
of the TV, the TV set automatically turn.(This function  
is not available for LD42K3)  
and then press  
/
ꢂꢃ  
to adjust it.  
Language  
Two languages (i.e. Simplified Chinese and English)  
are available for your choice.  
Back light LED Four...  
OPC  
Surround  
Press  
/
to select the OPC , then press  
/
to  
ꢂꢃ  
ꢂꢃ  
Prog...  
DTV Manu...  
select Uesr/Dynamic/Daylight/ Normnal/Night.  
Press to select the Adjust , then press  
to set 0-10.  
Intelligent  
Mode  
Net  
Upgrade  
/
/
ꢂꢃ  
Chinese  
Press  
adjusted, and then press  
OFF.  
/
to select theDynamic Contral to be  
/
ꢂꢃ  
to select ON or  
Back light LED Four...  
Contrast  
Brightness  
Color  
Sharpness Tint  
Reset  
Picture  
Palette  
OPC  
Sound Volume  
OPC Mode  
Adjust  
<
<
<
User  
10  
>
>
>
Menu Timeout  
Programe. A
Channel  
Dynamic Control  
Off  
Auto..  
Eye Guard  
Mode  
Net  
Upgrade  
Language M
The option is for adjusting the menu display time.  
Press to set the desired time (5-30s).  
/
ꢂꢃ  
Function  
Image Po.. Horizont  
Wertical.  
Clock  
Phase  
Reset  
Adjust  
Picture Optimize  
Current..  
Off Time  
Off Time On Channel Remind T.. Remind C..  
Timer  
Press  
/
to select the Picture Optimize option.  
%$&.  
029(  
MENU  
OK 2.  
Press OK to enter the submenu.  
Press to select theDCDI/Color  
Management /Background to be adjusted, and  
then press to select ON or OFF.  
Press  
and then press  
High/ Off.  
/
Eye guard Mode  
Press  
/
to select the Eye guard Mode option.  
Press OK to enter the submenu.  
to select the Power E.G.Mode , then press  
to select Standard/Eye Guard/Curtain.  
to select the Change Ch.E.GI/  
Watching E.G/Watching E.G.Delay to be adjusted,  
and then press to select ON or OFF.  
/
ꢂꢃ  
ꢂꢃ  
/
to select the DNR to be adjusted,  
Press  
/
/
ꢂꢃ  
to select Low/Middle/  
/
ꢂꢃ  
Press  
/
Note The Background function is not available for LD42K3.  
/
ꢂꢃ  
Back light LED Four...  
Contrast  
Brightness  
Color  
Sharpness Tint  
Reset  
Picture  
Palette  
Eye GuardMode  
Sound Volume  
PowerOn E.G.Mode  
Change Ch.E.G  
Watching E.G  
<
<
<
<
Standard  
>
>
>
Programe. A
Channel  
On  
Off  
Eye Guard  
Mode  
Net  
Upgrade  
Language M
Watching E.G.Delay  
Off  
>
Function  
Image Po.. Horizont  
Wertical.  
Auto..  
Clock  
Phase  
Reset  
Adjust  
Current..  
Off Time  
Off Time On Channel Remind T.. Remind C..  
Timer  
%$&.  
029(  
MENU  
OK 2.  
18 LED -LCD television Owner’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Receiving and Playing Operations  
Time Menu  
Net Upgrade  
Press  
/
to select OK or Cancel to upgrade the TV  
ꢂꢃ  
A
Press MENU button and then use  
select Time menu.  
/
button to  
set by internet and flash.  
B
Press  
/
to select the desired option, press OK  
Adjust Menu  
to enter its submenu.  
The TV can be used as a display, and you may adjust  
relevant settings. Press SOURCE to switch the signal  
input to PC mode.  
A
Press MENU to display the screen main menu, and  
then press to select the Adjust menu as  
shown in the below figure.  
/
Current Time: The current time is calculated from the  
moment upon turning the TV on. At first, check whether  
the time indicated on the TV's clock is consistent with the  
standard time of your time zone; if not, adjust the clock as  
follows:  
Press MENU on the remote control unit or MENU  
on the TV’s front panel to display the main menu,  
B
C
Press  
Press  
/
ꢂꢃ  
to select the option to be adjusted.  
to adjust it.  
and then press  
afterwards press  
option, press OK to enter the submenu.  
/
to select the Timer menu,  
to select the Current Time  
/
ꢂꢃ  
/
ꢂꢃ  
Image Position  
This is used to adjusting H-Position and V-Position.  
Press  
/
ꢂꢃ  
to set hour and minute.  
Press  
/
to adjust the time.  
Horizontal-Size  
After finishing time setting, press OK or MENU to  
Press  
/
ꢂꢃ  
to adjust it(0---100).  
confirm.  
Vertical-Size  
Press  
/
ꢂꢃ  
to adjust it(0---100).  
Off Time/On Time: Set a time for the TV to  
turn off or on.This function allows the TV to  
automatically turn on or enter standby mode  
upon reaching the preset time.  
Auto Adjust  
Vertical and Horizontal position of picture can be  
adjusted in this item.  
Press OK to enter the setting screen, and then  
Clock  
press  
press  
/
to select ON or OFF, if you select ON,  
to set hour and minute. ON indicates  
This is used for adjusting the phase of pixel clock in PC  
mode.  
/
ꢂꢃ  
the On/Off Time function is enabled while OFF  
indicates the function is disabled.  
.After finishing time setting, press OK or MENU to  
confirm.  
Phase  
This is used for adjusting H Position and V Position as  
well as relative parameters in PC modes.  
Reset  
Note  
Return to factory default settings.  
After setting the On/Off Time function, if the TV is AC  
off or forcible DC off, the function will be automatically  
LED -LCD television Owner’s Manual 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Receiving and Playing Operations  
cleared.  
Lock Set  
On channel: This function is used in combination with  
the On/Off Time function. When the TV turns on upon  
reaching the On time, it automatically enters the preset  
channel.  
Change Password  
OK  
off  
Tuning Lock  
Preset Source  
Preset Prog  
Source Lock  
Child Lock  
off  
off  
Press OK first and then press  
Channel or OFF.  
/
ꢂꢃ  
to set the On  
OK  
off  
Max Volume  
Power On Volume  
Unlock  
100  
off  
OK  
Remind Time/Remind channel: The remind time and  
remind channel functions allow the TV to automatically  
enter the preset channel at preset time. If the TV is AC off  
or forcible DC off, the preset time will be cleared.  
Change Password  
After entering the Lock Set menu, press  
Press MENU on the remote control unit or MENU  
on the TV's front panel to display the main menu,  
/
to  
select the Change Password option, and then press  
OK to display the Change Password menu, afterwards  
enter a new 4-digit password by pressing numerical  
keys and repeat entering this password once again.  
If the user does not want to change the password in  
halfway, he may press MENU to exit from this menu.  
and then press  
afterwards press  
Time option.  
/
to select the Timer menu,  
to select the Remind  
/
ꢂꢃ  
Press OK to enter the setting screen, and then  
press  
press  
press  
/
to select ON or OFF, if you select ON,  
to set hour and minute, and then  
to adjust time.  
/
ꢂꢃ  
Note  
/
After finishing time setting, press OK or MENU to  
The initial password is 0000, and the password setting  
will not be changed after executing the Unlock  
option.  
confirm  
Press  
/
to select the Remind Channel  
ꢂꢃ  
option, and press OK first and then press  
/
ꢂꢃ  
Tuning Lock  
to set the found  
.
Press  
then press  
/
to select the Tuning Lock option, and  
/
to set ON or OFF.  
ꢂꢃ  
Lock Setup  
The television has the function of security default lock.  
Password needs to be entered when the program lock  
mode is to be set.  
(If set ON, the Tuning Menu is not available in TV  
mode. To make any operation related to the Tuning  
Menu, it need to enter the Lock Set menu to set  
Tuning Lock OFF or execute the Unlock option.)  
Preset Source Setting  
Preset Source may be set as Off, TV, AV,Component,  
HDMI, PC and USB. When the Preset Source is set as  
TV, after entering the Preset Channel menu, press  
How to use the password function  
/
to select the preset channel, and the channel  
Press H. LOCK, the TV screen will display Enter Password  
to prompt the user to enter password by pressing  
corresponding numerical keys; if the password is correct,  
the user enters the Lock Set menu; if incorrect, the user is  
required to enter a password again.  
ꢂꢃ  
will be forcibly switched to the preset one upon  
turning the TV on; when the Preset Source is set as  
other signal sources, the TV will be forcibly switched to  
the preset source upon turning on. For example, when  
the Preset Source is set as YPbPr/YCbCr, the TV will be  
switched to YPbPr/YCbCr upon turning on; when set as  
OFF, the preset function will be closed.  
If there is no operation for a few seconds, the display will  
automatically disappear.  
The Lock Set menu is as follows:  
Preset Prog  
Only when the Preset Source is set as TV can the  
Preset Channel option be available. Press  
select preset channels from 0-255.  
/
ꢂꢃ  
to  
20 LED -LCD television Owner’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Receiving and Playing Operations  
Source Lock  
This function is used to prohibit watching a program  
from various external inputs, e.g. AV and PC, etc. Press  
To watch a 3D TV  
/
to select a certain option, and then press OK  
to enter the submenu, press  
/
to set an external  
ꢂꢃ  
If the TV is currently in the 2D  
input lock ON or OFF. If an external input lock is set  
ON, after entering this mode, the screen will display  
blue background with muting and a prompt Source  
Lock; during Source Lock prompt, Source Lock will  
remain if there is no other display on the screen. To  
watch a program from a locked external input, just  
enter Source Lock submenu to set corresponding  
status as OFF or execute the Unlock option in the Lock  
Set menu.  
mode:  
Stand-by switch  
Child Lock Setting  
Press  
press  
/
to select the Child Lock option, and then  
to set ON or OFF. If set ON, this control  
/
ꢂꢃ  
key will not respond, and the screen will display Child  
Lock when the key is pressed; if no other operation is  
made, the display will automatically disappear later.  
To resume Child Lock function, just enter the Lock Set  
menu to set Child Lock OFF or execute the Unlock  
option.  
Max Volume Setting  
Press  
then press  
/
to select the Max Volume option, and  
/
to freely adjust the max volume  
ꢂꢃ  
within the range of 0~100. After finishing the setting,  
the max volume in the Volume menu will not exceed  
the preset max volume; for example, if the preset  
max volume is 30, the volume in the Volume menu  
can not be increased any longer upon reaching 30;  
if the preset max volume is less than the value in the  
Volume menu, the latter will decrease along with the  
decrease of preset max volume.  
3D switch key  
Power on Volume  
Press  
and then press  
within the range of 0~100.  
/
to select the Power on Volume option,  
/
to freely adjust the volume  
ꢂꢃ  
Unlock Setting  
Press  
/
to select the Unlock option, and then  
press OK to clear all the lock settings, namely set all  
the lock setting options as OFF; the Preset Channel  
is set as OFF and max volume returns to 100 (except  
password).  
A
Press the 3D switch key on the remote control  
to call out the prompt menu. (See Fig. 1 below)  
Advanced function  
LED -LCD television Owner’s Manual 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Receiving and Playing Operations  
Streaming Media Playing  
System  
Note  
The diagrams in the following section are  
schematic and only for your reference. Please see  
the actual product if necessary.  
B
Press  
/
to select the “Confirmoption, you will  
ꢂꢃ  
enter the interface for selecting a corresponding 3D  
mode. (See Fig. 2 below)  
A
Supported file formats:  
Picture: . JPEG; PNG; BMP;  
*
Music: . Mp3(8-320kbps; WMA(32-192kbps);  
*
AAC(16-576kbps)  
Movie:  
MPEG4: . avi files in accordance with Div*4. x/5. x  
*
Protocol;  
MPEG2: some . mpeg files;  
*
MPEG1: . dat and some . mpeg files;  
RealVideo  
*
*
If the TV is currently in the 3D  
mode:  
Text: . Txt.  
*
Note  
Due to the particularity of file coding, some files  
may be unable to be read.  
A
Press the 3D switch key on the remote control to call  
out the prompt menu. (See Fig. 3 below)  
B
Supported equipment:  
B
Press  
exit.  
/
ꢂꢃ  
keys to exit the 3D mode or cancel the  
Support the equipment that supports Mass Storage  
Protocol and whose file system is FAT/NTFS/FAT16/  
FAT32, such as some USB disks, mobile hard disks,  
card readers, MP3 players and digital cameras.  
If USB equipment could not be identified due  
to unsupported file system, please format the  
equipment to the above-mentioned file system;  
Note  
When you watch a 3D TV program, please wear  
and turn on 3D glasses.  
If the signal currently detected in the HDMI  
channel is one of 3D signals specified in the  
Specification HDMI1.4a, selecting the “Confirm”  
option will make the TV directly switch to a  
corresponding 3D mode, so the above Fig. 2 will  
not appear and you needn’t choose a 3D mode.  
C
The external card reader supports most of the digital  
cards in the current market; the types of digital cards  
that can be read are relevant to the performance  
of selected card reader; you may attach standard  
mobile hard disks (working voltage 5.0V, working  
current not higher than 500mA); during media  
playing, do not pull out storage media, otherwise it  
may cause system halt, damage the files in storage  
media or damage USB equipment; sometimes, the  
TV may halt due to overhigh information error rate,  
in which case you should restart the system; there  
are a lot of nonstandard USB mobile equipment  
in the market, they may not be identified when  
connected to the streaming media playing system;  
the above phenomena may also occur on computers  
and are not the TV’s fault.  
In the 3D mode, the TV screen display menu can  
still be called out and displayed normally.  
The TV doesn’t memorize the setting of 3D mode,  
so it will be in the 2D mode when you turn it on  
again after turning it off.  
In the USB mode, there are various modes of 3D  
video sources. With USB signals, the 3D switch key  
functions only when playing a video (film). The TV  
will exit the 3D mode when playing ends or when  
you manually exit the 3D mode.  
D
To achieve smooth playing, ensure the following:  
Advanced function  
22 LED -LCD television Owner’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Receiving and Playing Operations  
The file code rate should be lower than 300KB/S;  
Due to the limitation of USB signal transmission  
distance, it is recommended not to use USB patch  
cord, in case of using the cord, make sure that its  
length is not over 1m;  
Use high-speed USB equipment in conformity  
with USB2.0 Interface Standard; if USB equipment  
in conformity with USB1.1 Interface Standard is  
used, the playing may be unsmooth.  
E
Although many movie files are with such postfixes as  
avi and mpeg, actually there are several formats in the  
files; however, the TV can only play some files in avi  
and mpeg formats. Some files with the postfix "dat"  
are not movie files, but data files commonly used in  
computers, and they can not be played as movies.  
Operating Method of Streaming  
Media Menu  
A
Press  
/
to scroll through main menu or  
submenu and select your desired option.  
Start/Exit Streaming Media Playing  
System  
B
C
Press OK to confirm your selection.  
Press REV/FWD to achieve the FF (fast forward) and  
FB (fast back) of the movie or music being played.  
A
Press USB on the remote control unit to select the  
streaming media function. press  
zmplayer, press OK to enter.  
/
ꢂꢃ  
to select  
D
E
F
G
Press PLAY/PAUSE to pause playing, and press it  
again or press OK to continue playing.  
B
C
Insert USB equipment into corresponding USB  
interface 2s after starting the system.  
Press ZOOM to magnify pictures; in zoom mode,  
press  
/
ꢂꢃ  
and  
/
to move the picture.  
After entering the system menu, press  
/
on  
ꢂꢃ  
Press OK to display and press EXIT to exit the screen  
the remote control unit to select the required USB  
equipment, and then press on the remote  
display information while playing.  
/
Press BACK to stop playing, or return to the previous  
menu, and press BACK repeatedly to return to the  
main menu.  
control unit to select the required file.  
Playing a Picture  
A
After entering USB main interface, press  
select a harddisk partition, and then press  
select the Picture option.  
/
ꢂꢃ  
to  
to  
/
D
E
Press OK to enter the selected file.  
To exit the streaming media playing system and  
watch a TV program, you must return to the  
streaming media main menu at first (to protect  
equipment), and then press SOURCE to select TV or  
directly press USB to return to the TV mode.  
B
Press OK to confirm the selection and enter the  
picture playing interface.  
LED -LCD television Owner’s Manual 23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Receiving and Playing Operations  
Press to change page, and press  
D
To exit playing, just press BACK repeatedly.  
C
/
/
to  
ꢂꢃ  
ꢂꢃ  
select the picture you want to play, and then press  
OK to enter the playing display interface.  
Note  
Press ZOOM to magnify the picture, and then  
The menu display varies with the number and  
names of files in your equipment.  
press  
Press  
Press  
/
/
/
to move the picture.  
ꢂꢃ  
/
to select the last or next picture.  
to rotate the picture.  
ꢂꢃ  
/
Playing Music  
A
After entering USB main interface, press  
select a harddisk partition, and then press  
select the Music option.  
/
to  
ꢂꢃ  
/
to  
to  
PLAY/PAUSE  
B
C
Press OK to confirm the selection and press  
play the music of your choice.  
FWD  
D
To exit playing, just press BACK repeatedly.  
REV  
PLAY/PAUSE  
Press  
to control the muDsi.CcALL  
you currently enjoy. In music playing, press  
button to Switch Play mode of 3: repeat single  
Playing a Movie  
A
After entering USB main interface, press  
select a harddisk partition, and then press  
select the "Movie" option.  
/
to  
ꢂꢃ  
/
ǃrepeat randomly  
ǃrepeat all  
to  
D
To exit music playing, just press BACK repeatedly.  
B
C
Press OK to confirm the selection and enter the  
movie playing interface.  
Press  
/
to change page, and press  
/
to  
ꢂꢃ  
select the movie you want to play, and then press  
Text  
OK to enter the playing display interface.  
Press  
/
ꢂꢃ  
to select the last or next movie.  
A
After entering USB main interface, press  
select a harddisk partition, and then press  
select the Text option.  
/
to  
ꢂꢃ  
/
to  
B
C
Press OK to confirm the selection and enter the text  
playing interface.  
Press  
/
/
/
to select the text you want  
ꢂꢃ  
to read, and then press OK to play the text reading  
interface. Press to change page, and press  
/
BACK to exit the reading interface.  
24 LED -LCD television Owner’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance / Troubleshooting  
Note  
Maintenance  
The red button on the control can doing some  
delete. Text playback support TXT format.  
Maintenance  
Early malfunctions can be prevented. Careful and regular  
cleaning can extend the amount of time you will have  
your new TV. Be sure to turn the power off and unplug  
the power cord before you begin any cleaning.  
Cleaning the Screen  
A
Here’s a great way to keep the dust off your screen  
for a while. Wet a soft cloth in a mixture of lukewarm  
water and a little fabric softener or dish washing  
detergent. Wring the cloth until it’s almost dry, and  
then use it to wipe the screen.  
D
To exit the Text mode, just press BACK repeatedly.  
Settings  
B
Make sure the excess water is off the screen, and  
then let it air-dry before you turn on your TV.  
A
After entering USB main interface, press  
/
to  
select the Settings option.  
Cleaning the Cabinet  
B
Press OK to confirm the selection and enter the  
settings selection interface, and then press  
to select the required options.  
/
To remove dirt or dust, wipe the cabinet with a soft, dry,  
lint-free cloth. Please be sure not to use a wet cloth.  
Extended Absence  
If you expect to leave your TV dormant for a long time  
(such as a vacation), it’s a good idea to unplug the power  
cord to protect against possible damage from lightning  
or power surges.  
Troubleshooting  
For the sake of time and cost, it is strongly  
recommended that you checkout the problem by  
yourself according to the instructions listed hereunder  
before contacting the after-sales service for technical  
assistance.  
Photo Slide Time  
Set the scan speed of pictures to be scanned in slide  
form.  
There are three options (Middle/Slow/fast). Press  
/
ꢂꢃ  
to select the desired option.  
Movie Subtitle  
Press  
/
ꢂꢃ  
to select "ON" or "OFF".  
Problem  
Possible remedies  
LED -LCD television Owner’s Manual 25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specification  
sound might be produced. These phenomena  
might happen in the area 1,500 meters above the  
sea level. This is resulted from difference between  
air pressures inside and outside the display. This is  
not a defect covered by the limited warranty.  
Turn onthe power supply; Properly  
plug theTV setto the powersocket;  
Check to see if the power cable of other  
appliance is plugged in the TV set. Make  
sure that the power cable of the TV set  
is properly connected.  
No  
picture,  
no sound  
Problem  
Possible remedies  
Specification  
Basic specification and parameter  
Good  
picture,  
no sound  
Depress the volume button;  
Check out theaudio frequency input signals.  
Check to see if the remote controller  
display receiving window are blocked  
by other objects and if batteries are  
properly loaded.  
Power  
~ 150-240V 50/60Hz  
Failure of  
remote  
controller  
Color System PAL, SECAM  
Stand-by  
D/K, B/G, I  
Designate the item of color from the  
Picture menu and depress the volume  
button; Keep the display and VCR  
Consumption  
No color,  
Video Input  
USB,AV, Component, HDMI or PC,  
weak color separate a reasonable space; Activate  
or poor  
picture  
some functions to store picture  
brightness; Make sure that the display  
and signal source are available and  
turned on.  
Operating temperature range:  
+5°C - +35°C Operating  
humidity range: 20%-80%  
Storage Temperature:  
-15°C~+45°C  
Storage Humidity: 5%-90%,  
non-condensing  
Excessive  
brightness  
or darkness  
Adjust brightness or contrast.  
Environmental  
condition  
Picture  
too big or  
small  
If the storage temperature is  
lower than 0 °C, please first  
lays the machine aside after  
in the operating temperature  
environment carries on restores  
2 hours, then electrifies the use  
again, protects your television  
not to receive the damage.  
Adjust the setup of sizes.  
One  
speaker  
failure  
Balance the sound in the menu.  
Slight  
sound  
from  
It is a normal phenomenon.  
display  
Owner’s manual x1  
Remote Control  
Alkaline battery  
x1  
x2  
Accessories  
(This is only available for certain  
Note  
models,please refer to actual products.)  
Do not leave the television with static picture in an  
extended period as it may result in residual image  
on your television screen.  
Product main size (contain stand)  
Note  
Power  
Net  
MODEL  
Net Size(LxWxH)  
Consumption  
Weight  
Production of the screen requires high and precision  
technologies. However, there might be some  
dank or bright (red, blue or green) spots, or some  
anomalistic stripes or spots. This is not defect. If the  
TV set is used in an area 2,400 meters above the sea  
level where the air pressure is below 750hpa, the  
picture on the screen maybe affected and a muffled  
LE42H330  
LE46H330  
LE55H330  
LD42K3  
110W  
130W  
160W  
120W  
1012x41x622mm  
1107x55x733mm  
1308x55x845mm  
1021x290x704mm  
15.7Kg  
18.2Kg  
25Kg  
18.2Kg  
26 LED -LCD television Owner’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Format  
1
2
3
4
480i/480p  
576i/576p  
720p  
60  
Note  
Design and specifications are subject to change  
without notice. The dimension in this manual is a  
50  
50/60  
50/60  
approximation.  
1080i/1080p  
Format  
Recommendatory HDTV/  
SDTV(YP P /YC C ) format  
b r  
b r  
Sequence  
Number  
Refresh  
Frequency (Hz)  
Format  
1
2
3
4
480i/480p  
576i/576p  
720p  
60  
50  
50/60  
50/60  
1080i/1080p  
Recommendation PC connection  
input format  
sequence  
number  
H-Frequency  
(KHz)  
V-Frequency  
(Hz)  
Format  
1
2
640*480@60Hz  
800*600@60Hz  
31.5  
60  
60  
37.88  
1024*768@60Hz  
(Recommendatory)  
3
48.36  
60  
Recommendation DVI connection  
input format  
Sequence  
Resolution  
Refresh Frequency (Hz)  
Number  
1
2
3
640*480  
800*600  
1024*768  
60  
60  
60  
Recommendation HDMI  
connection input format  
Sequence  
Number  
Format  
Refresh Frequency (Hz)  
LED -LCD television Owner’s Manual 27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specification  
28 LED -LCD television Owner’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Format  
LED -LCD television Owner’s Manual 29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specification  
30 LED -LCD television Owner’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Format  
LED -LCD television Owner’s Manual 31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specification  
Specification / Format  
32 LED -LCD television Owner’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Format  
LED -LCD television Owner’s Manual 33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specification  
34 LED -LCD television Owner’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Format  
LED -LCD television Owner’s Manual 35  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Grizzly Saw G1052 User Manual
Haier Flat Panel Television L1509 A User Manual
Haier Washer XPB80 50 User Manual
Honeywell Wheelchair AT120A User Manual
Hotpoint Cooktop HUE User Manual
Hotpoint Refrigerator CTX18BACWW User Manual
HP Hewlett Packard Power Supply 6235A User Manual
HP Hewlett Packard Projector HP ep7100 User Manual
Hunter Fan Ventilation Hood 81003 User Manual
Hypertec Indoor Furnishings Simple Footrest User Manual