DISHWASHER OPERATION MANUAL
EN
DW12-TFE5
PLEASE READ THIS OPERATION MANUAL BEFORE USING THE DISHWASHER.
0120504965D
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connection (Uk Only)
For your safety please read the following information.
Warning: This appliance must be earthed.
The appliance must be connected to a 220-240 volts 50 cycle AC supply by means of a three pin
socket, suitably earthed and should be protected by a 13 amp fuse in the plug.
The appliance is supplied with a rewireable 13 amp 3-pin plug fitted with a 13-amp fuse. Should the
fuse require replacement, it must be replaced with a fuse rated at 13 amp and approved to BS1362.
If the mains plug is unsuitable for the socket outlet in your home or is removed for any other reason,
then the cut off plug should be disposed of safely to prevent the hazard of electric shock. Remove the
fuse before disposal.
There is a danger of electric shock if the cut off plug is inserted into any 13-amp socket outlet.
How to wire a 13 amp plug.
Important
The wires in the mains lead on this appliance are coloured in accordance with the following code:
Green and Yellow-Earth Blue-Neutral Brown-Live
As the colours may not correspond with the markings identifying the terminals in your plug proceed as
follows.
The green and yellow wire must be connected to the terminal in the plug which is marked with the letter
E or with the earth symbol
or coloured green and yellow.
The blue wire must be connected to the terminal marked N.
The brown wire must be connected to the terminal marked L.
You must make sure the lead is firmly secured under the cord clamp.
Download from Www.Somanuals.com. All Manuals Search And Download.
Important safety information
This appliance must be earthed. It is intended for use on a 220-240Volt 50Hz mains supply.
Check that the voltage marked on the rating plate matches that of your local supply before plugging in
for the first time.
Improper connection of the grounding conductor can result in the risk of an electric shock.
Check with a qualified electrician or service representative if you are in doubt whether the
appliance is properly grounded. Do not modify the plug provided with the appliance; if it does not fit
the outlet. Have a proper outlet installed by a qualified electrician.
Check packaging and dishwasher immediately for signs of transport damage. If the appliance is
damaged, do not put it into use but contact your supplier or customer service without delay.
This dishwasher must be plugged into a separate mains socket that is earthed and remains accessible at
all times, even after installation.
The dishwasher must only be used for the washing of household dishes and cooking utensils.
This appliance cannot be installed outdoors, not even if the area in which it is installed is covered by
a roof; it is also very dangerous to leave it exposed to rain.
Check that the voltage marked on the rating plate matches that of your local supply.
If the supply cord is damaged, it must be replaced by the manufacture, its service agent of similarly
qualified person with a cord of the same type and rating in order to avoid a hazard.
Never disconnect from the mains by pulling on the mains cord, always grasp the plug.
Never touch the dishwasher when barefoot or with wet hands or feet;
We discourage the use of extension cords and multiple sockets as they constitute a tripping
Hazard and might cause a fire.
Do not open the door during a wash cycle as hot steam and water may be ejected.
Do not touch the heating element during or just after a wash cycle.
Do not overload the dishwasher; the maximum number of place settings is 12.
Do not sit or stand on the door or place heavy objects on it as the dishwasher will tip forward.
Do not let children play on or near the dishwasher.
Do not let anything including carpets block ventilation openings in the base of the appliance.
Do not use the dishwasher if the mains cord is damaged, if it is damaged in any way or does not
operate as expected, contact the store where you purchased the dishwasher for advice.
The inlet water pressure must be no lower than 0.03 MPa and no higher than 1 .0 MPa.
Connect to the water mains using new hose sets; do not re-use old hose sets.
This appliance is not intended for use by persons (including children) with reduced physical sensory
or mental capabilities or lack of experience and knowledge unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
Check Plastic items are dishwasher safe. You must prevent them coming into contact with the heating
elements during a washing cycle.
The door shall not be left in the open position since this could present a tripping hazard.
WARNINGS:
Knives and other utensils with sharp points must be loaded in the basket with their points down or
placed in a horizontal position.
THIS APPLIANCE IS INTENDED FOR DOMESTIC USE ONLY; ANY OTHER USE MAY
INVALIDATE THE WARRANTY AND MIGHT BE DANGEROUS. USE THIS APPLIANCE FOR
ITS INTENDED USE ONLY.
Dishwasher detergent is strongly alkaline! Take care to keep it out of reach of children.
If you are discarding an old appliance with a lock / catch fitted to the door, ensure that it is in a
disabled condition to avoid the entrapment of children when playing.
Disconnect from the mains, remove the plug and cut the mains cable off close to the appliance before
disposal at end of life, take the appliance to your local recycling point.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Index
Safety information
Installation
Getting to know your dishwasher
How to fill the salt
2
4
6
7
8
How to fill rinse aid
9
How to fill the detergent dispenser
Not suitable for the dishwasher
Arranging crockery, glasses, etc. in the dishwasher
Programme overview
Washing dishes
How to keep your dishwasher in shape
Care and maintenance
Trouble Shooting
Technical data
Important information
10
11
13
15
18
19
20
25
25
Disposal
The symbol
on the product or on its packaging indicates that this product
may not be treated as household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent poten-
tial negative consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this product.
For more detailed information about recycling of this product, please contact
your local city office, your household waste disposal service or the shop where
you purchased the product.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Safety information
At time of delivery
Check packaging and dishwasher immediately for signs of transport damage. If the appliance is dam-
aged, do not put it into use but contact your supplier or customer service without delay.
Please dispose of packaging materials properly.
During installation
Site the dishwasher and connect it up in accordance with the installation instructions.
The dishwasher must not be connected to the electricity supply while installation is being carried out.
Ensure that the domestic wiring is properly earthed.
The mains electricity supply must conform to the details shown on the dishwasher nameplate.
Do not connect the dishwasher to the electricity supply via an extension cable.
Built-under and built-in appliances should always be installed under a continuous work surface which
is attached to the adjacent cupboards, in order to ensure that the appliance is entirely stable.
After the appliance has been installed,the mains plug should still be easily accessible.
During installation, the power supply cord must not be excessively or dangerously bent or flattened.
During normal use
The dishwasher must only be used by adults for the washing of household dishes and cooking utensils.
This appliance cannot be installed outdoor, not even if the area in which it is installed is covered by a
roof; it is also very dangerous to leave it exposed to the rain and elements.
Do not place any heavy objects or stand on the door when it is open. The appliance could tip forward.
The water inside the dishwasher is not suitable for drinking.
Do not use solvents of any kind inside your dishwasher. They could cause an explosion danger.
Open the door very carefully if the dishwasher is operating. There is a risk of water squirting out.
Do not touch the heating element during or after a wash cycle.
Fundamental rules to follow when using the appliance:
- Never touch the dishwasher when barefoot or with wet hands or feet;
- We discourage the use of extension cords and multiple sockets;
- If the appliance is not operating properly or maintenance must be performed, disconnect the
appliance from the power supply.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
If your family includes children
This appliance is not intended for use by persons (including children) with reduced physical,sensory
or mental capcabilities, or lack of experience and knowledge,unless they have been given supervi-
sion or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they to not play with the appliance.
Keep detergents out of the reach of children, who must also be kept away from the dishwasher when
it is open.
If a fault occurs
If the appliance malfunctions, turn off water supply to the appliance and disconnect the power supply
turn off and the plug from the wall socket. Then, consult the section entitled, "Fault finding" .If you
cannot solve the problem, contact a service center.
Only specialised personnel are authorised to make repairs.
If the supply cord is damaged, it must be replaced by the manufacture, its service agent of similarly
qualified persons in order to avoid a hazard.
To maintain the EFFICIENCY and SAFETY of this appliance,we recommend:
- call only the Service Centers authorized by the manufacturer, or the approved Service agents.
- always use original Spare Parts.
When disposing of old appliances
Appliances which are no longer being used must be made inoperable by cutting the power supply
cord and removing the door lock.
Take the appliance to a designated waste disposal center.
Dangerous voltage
Warning
Children could get locked in the appliance (risk of suffocation)
or get stuck in other positions. Therefore: Remove the mains
plug, cut the mains wire and set aside. Damage the door lock so
that the door can no longer be closed.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
EN
Positioning the appliance
Positioning the appliance in the desired location. The back of the appliance should rest against the wall,
and the sides, along the adjacent cabinets or wall. The dishwasher is equipped with water supply and
drain hoses that can be positioned to the right or the left to facilitate proper installation.
Levelling the appliance
Once the appliance is positioned, adjust the feet (screwing them in or out) to adjust the dishwasher,
making it level. The appliance should not be inclined more than 2˚. If the appliance is level, it will help
ensure proper performance.
Cold water connection
Connect the water supply hose to a threaded 3/4 (gas) connector,
making sure that it is fastened tightly in place (see fig.A).
Some models are fitted with an "Aquastop" water supply hose
(see fig.B) in which the small filter is already housed in the
threaded end.
fig.A
fig.B
If the water pipes are new or have not been used for an extended
period of time, let the water run to make sure that the water is
clear and free of impurities. If this precaution is not taken, there
is a risk that the water inlet can get blocked and damage the
appliance.
Warning
The appliance is to be connected to the
water mains using new hose-sets and
that old hose-sets should not be reused.
Anti-Flooding protection
The dishwasher is equipped with a system that stops the supply of water in the event of a problem with the water
supply hose, or leaks within the unit, in order to prevent damage to your home. If for any reason the box contain-
ing the electrical components happens to get damaged, turn off the power supply and remove the plug for the
appliance from the socket immediately. In order to guarantee that the anti-flooding feature operates properly, the
"A" box with water supply hose must be attached to the water supply tap as shown in fig.B. No other type of
connection is acceptable.The water supply hose must not, under any circumstances, be cut, as it contains
electrical parts which are live. If the length of the hose is not adequate to make a proper connection, the hose
must be replaced with one which is long enough. This hose is available upon request from specialised retailers
and approved service center.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Drain hose connection
Insert the drain hose into a drain pipe with a minimum diameter of 4cm, or let it run into the sink, making
sure to avoid bending or crimping it. If necessary, fit a syphon trap (U-bend) with a connecting piece for
the electrical drain hose (fig.C). The free end of the hose must be at a height between 40 and 100 cm
and must not be immersed in water.
fig.C
Attention:
The connecting piece for syphon trap (U-bend) must be securely
fastened to the wall to prevent the drain hose from moving and
allowing water to spill outside the drain.
Electrical Connection
After making sure that the voltage and frequency values for the current in the home correspond to those
on the rating plate (located on the stainless steel inner door of the appliance) and that the electrical
system is correct for the maximum voltage on the rating plate, insert the plug into an electrical socket
which is earthed properly (the earthing of the appliance is a safety requirement mandated by law).
If the electrical socket to which the appliance must be connected is not appropriate for the plug, replace
the whole cable, rather than using adaptors or the like as they could cause overheating and burns.
Caution:
The dishwasher plug must be accessible even when the appliance
is installed as a built-in unit so that maintenance can be done safely.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting to know your dishwasher
EN
Close-up view (control panel)
C
A
E
H
J
B
D F G I
Delayed Start Button
Time-remaining Indicator
Low Rinse Aid Indicator
Low Salt Indicator
State Indicator
ON-OFF Button
"1/2" Indicator
A
B
C
D
F
G
H
I
"1/2" Button
Knob For Selecting Cycle
J
Delayed Start Indicator
E
Dishwasher interior
i
a
c
b
j
e
f
k
d
g
h
a
b
c
d
e
f
g
h
i
Upper Rack
Washing Filter
Lower Rack
Detergent and Rinse Aid Dispenser
Water Inlet Hose
Top Spray Arm
Cutlery Basket
Bottom Spray Arm
Salt Container Cap
j
Drain Hose
k
Power Supply Cord
6
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
How to fill the salt
Salt
The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits
will form on the dishes and utensils.
The appliance is equipped with a special softener that uses a salt specifically designed to eliminate lime
and minerals from the water.
Loading the salt into the container
Always use salt intended for use with dishwashers.
The salt container is located beneath the lower rack and should be filled as follows:
When the low salt indicator “I” lights, you must fill the salt.
Remove the lower rack and then unscrew and remove the cap
H
from the salt container;
If you are filling the container for the first time, fill it with water;
Place the end of the funnel (supplied) into the hole and introduce
about 2 kg of salt. It is normal for a small amount of water to
come out of the salt container.
I
Carefully screw the cap back on.
Important
To prevent the formation of rust, load the salt just before beginning a wash cycle.
Adjusting salt consumption
The dishwasher is designed to allow for adjusting the amount of salt consumed based on the hardness of
the water used. This is intended to optimize and customize the level of salt consumption so that it re-
mains at a minimum.
To adjust salt consumption, proceed as follows:
Unscrew the cap from the salt container;
There is a ring on the container with an arrow on it (see figure to
the side).
If necessary, rotate the ring in an anticlockwise direction from the
"-" setting towards the "+" sign, based on the hardness of the
water being used.
It is recommended that adjustments be made in accordance with the following table:
Selector
knob
Salt
consumption
(Grams/cycle)
Hardness of the water
Autonomy
(cycles/2kg)
ºdH
ºfH
ºmmol/l
position
0J10
NMJOR
ORJRM
[RM
MJNT
MJNIT
NIUJQIQ
QIRJUIV
[UIV
L
M
L
NUJQQ
QRJUV
[UV
=?J?
jba
?H?
OM
QM
SM
SM
QM
OR
The default setting of the water softening system is -. - If using multi-functional tablets fill the salt
dispenser and set the adjuster to -; if the hardness of the water is greater than 60ºfH, set it to +.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
How to fill rinse aid
Rinse aid
H
I
This product makes dishes sparkle and helps them to dry without
spotting. The dispenser is located on the inside panel of the door .
When the low rinse aid indicator "H"on the control panel and the me-
chanical indicator "H1" on the dispenser light, you must load rinse
aid.
H1
Loading the rinse aid
Regardless of the type of detergent dispenser installed on your appliance,
you must proceed as indicated below when loading the rinse aid.
To open the dispenser, turn the "1" cap in an anti-clockwise direction
and then pour in the rinse aid, making sure not to overfill. The amount of
rinse aid used for each cycle can be regulated by turning the " 2" dose
adjustor, located beneath the "1" cap, with a screwdriver. There are 6
different settings; the normal dosage setting is 3.
1
2
Important
Proper dosage of the rinse aid improves drying. If drops of water remain on the dishes or spot-
ting occurs, the dosage adjustor should be turned to a higher setting. If the dishes have white
streaks, turn the dosage adjustor to a lower setting.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
How to fill the detergent dispenser
EN
Detergent
4
Detergent specifically intended for use with dishwashers must be used.
The dispenser must be refilled before the start of each wash cycle fol-
lowing the instructions provided in the "Programme overview". The de-
tergent dispenser is located on the inside panel of the door.
3
Loading the detergent
To open the " 3 " cover on the dispenser, press the "4" button.
The detergent for the wash cycle should be poured into the " 5 "
compartment.
6
The detergent for the pre-wash cycle should be poured into the “
6 ” compartment.
After the detergent has been placed in the dispenser, close the
cover and press down until it clicks in place.
5
Notice:
To facilitate closing the cover, remove any excess detergent on the edges of the dispenser.
Warning:
Do not place the tablets in the tub or the cutlery basket as this will result in poorer wash
results. The tablets should be placed in the detergent doser.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Not suitable for the dishwasher
EN
What you should not put into the dishwasher
Cutlery and tableware manufactured in whole or part from wood.They become faded and unsightly in
appearance.Furthermore,the adhesives that are used are not suitable for the temperature that occur
inside the dishwasher.Delicate decorative glassware and vases,special antique or irreplaceable china.
The decorative patterns on such items will not be dishwasher-proof.
Plastic objects that are not resistant to hot water, copper and pewter utensils are also not suitable.
Decorative patterns printed or painted onto the surface of crockery, glasses, etc.,aluminium and silver
items tend to become discoloured or faded if washed in the diswasher. Some types of glass can become
opaque in appearance after they have been washed many times in a dishwasher. Highly absorbent
materials, such as sponges and towels,should never be placed in the dishwasher.
Our recommendation
In future, only purchase table or kitchenware that has been confirmed as being dishwasher-proof.
Important
Dishes or cutlery that have been soiled by tobacco ash, wax,
Iubricating grease or paint, should not be put in the dishwasher.
Damage to glassware and other dishes
Possible causes
type of glass or manufacturing process
chemical composition of detergent
water temperature and duration of dishwasher programme.
Suggested remedy
Use glassware or porcelain dishes that have been marked ‘dishwasher-proof’ by the manufacture.
Use a mild detergent that is described as ‘kind to dishes’. If necessary, seek further information from
detergent manufacturers.
Select a programme with a low temperature and a short duration as possible.
To prevent damage, take glass and cutlery out of the dishwasher as soon as possible after the
programme has ended.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Arranging crockery, glasses, etc. in the dishwasher
Before placing the dishes in the dishwasher, remove larger food particles to prevent the filter from be-
coming clogged, which results in reduced performance.
If the pots and pans have baked-on food that is extremely hard to remove, we recommend that they are
soaked before washed. This will eliminate the need for extra wash cycles.
Pull out the rack to load the dishwasher.
Normal daily load
How to use the lower rack
We recommend that you place the most difficult to clean items
on the bottom rack: pots, pans, lids, serving dishes and bowls,
as shown in the figure to the right.
It is preferable to place serving dishes and lids on the sides of
the racks in order to avoid blocking the rotation of the top spray
arm.
fig.D
Pots, serving bowls, etc. must always be placed face down
(see fig.D) .
Deep pots should be slanted to allow the water to flow out.
The cutlery basket can be separated (see fig.E) so thatonly
one section may be used when the cutlery load is small.
This also makes space for additional pots and pansand the
basket can also be placed in the upper rack.
Cutlery should be placed in the cutlery basket withthe
handles at the bottom; if the rack has side racks, thespoons
should be located individually into the appropriateslots. Very
long utensils and knives should be placed in the horizontal
position at the front of the upper rack.
fig.E
Warning
knives and other utensils with sharp points must be loaded in the
basket with their points down or placed in a horizontal position.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
How to use the upper rack
The upper rack is designed to hold more delicate and lighter
dishware, such as glasses, cups and saucers, plates, small
bowls and shallow pans (as long as they are not too dirty).
Position the dishes and cookware so that they do not get
moved by the spray of water.
The upper rack vertical position can be adjusted by moving
the handles on both sides of the upper rack. Pull the rack fully
out towards you, pull the handles sideways to unlock both
handles. Move both at the handles at the same time to raise
or lower the top rack as required (see fig.F).
fig.F
Adjust the upper basket to the higher level and you have
more space to accommodate those taller pans and trays in
the bottom basket.
Shelf
Lean tall glasses and those with long stems against the shelf-
fig.G
not against other items to be washed.
Place glasses, cups and small bowls on the additional cup rack.
The additional cup rack can be swivelled in or out as required
(see fig.G).
Knife rack
The knife rack clips onto the side of the top basket, giving you
the freedom to wash your large sharp knives separately and
out of harm’s way (see fig.H).
fig.H
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme overview
EN
Type of
Condi-
tion of
food
Type of
food
remains
Amount of
food
remains
crokery e.g.
china, pots/
pans,
Wash
programme
1/2
Description of cycle
Load
cutlery,
remains
glasses, etc
Pre-wash with warm water.
Extended wash at 70°C.
Rinses with cold water.
Rinse with hot water.
Drying.
Pre-wash use cold water.
Extended wash at 55°C.
Rinse with cold water.
Rinse with hot water.
Drying.
Pre-wash use cold water.
Extended wash at 50°C.
Rinse with cold water.
Rinse with hot water.
Drying.
Soups,
Non-
delicate
casseroles,
sauces,
Intensive
Wash
stuck
a lot
on hard
potatoes,
pasts, rice,
eggs, roast or
fried food.
Normal
Wash
Soups,
potatoes,
pasta, rice,
eggs, roast or
fried food.
loosely
attached
a little
Light Wash
Wash at 45°C.
Rinse with warm water.
Hot rinse.
Coffee,cakes,
milk, sausage,
cold drinks,
salads
Glass
ware
Drying.
loosely
attached
Very little
Mixed
Short wash at 40°C.
Cold rinse.
Rapid
wash
For dishes that need to be rinsed
and dried only.
Hot rinse at 65°C.
Drying.
Heat
Soak
Short cold wash to pre-
vent food residue from
drying on the dishes .
Rinse off if the dishes have been
stacked for several days in the dish-
washer prior to washing.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Detergent
Delayed
Start
Energy
Water
consump-
Duration in
minutes
Rinse Aid
consump-
Extended
Wash
Prewash
5g
tion in kWh tion in litres
25g
112
94
18
16
1.62
1.48
1.24
1.15
1.02
1.00
1.12
1.10
0.40
25g
25g
5g
5g
102
90
15
14
14
14
12
11
25g
25g
5g
5g
162
140
92
25g
15g
5g
10g
15g
82
32
9
8
10g
15g
28
54
48
0.30
0.90
0.78
5.5
5
12
12
3
3
0.02
0.02
14
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Washing dishes
Programme selection
The most appropriate programme can be identified by comparing the type of crockery, cutlery, etc., as
well as the amount and condition of food remains, with the details contained in the wash cycle table.The
corresponding programme sequence, duration and consumption details are shown in the right half of the
overview. For example:
Use the« normal» programme for dishes and utensils which have plenty of food remains stuck on hard.
Energy saving
If only a small number of dishes have been loaded into the dishwasher,selecting a programme that
operates at the next lowest temperature which should be sufficient.
Programme data
The stated programme data are based on standard operating conditions. The values can vary consider-
ably according to:
different amounts of dishes
temperature of mains water supply
pressure of mains water supply
ambient temperature
fluctuations in mains voltage
machine-related factors (e.g. temperature, water volume,...)
Switching the dishwasher ON
Turn on the tap.
C
Close the door after loading the appliance
A
B
E
H
I
Set On-Off button “B” to On. The state indicator "A" light.
Rotate the knob to select programme you wish.
The time-remaining indicator display
the time of the programme you selected.
D F
G
After 3 seconds the appliance emits a short warning signal,
and start the programme, the state indicator "A" blinks .
Warning
When the dishwasher is switched on, the program will not start until the program
selector knob has been turned to “Reset” and back to the selected wash program.
Then there will be a delay of approximately 30 seconds before the dishwasher
starts.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
End of programme
Six beeps will indicate that the wash cycle has finished and the state indicators "A" light.
Switching the dishwasher OFF
Several minutes after the programme has ended:
Set On-Off button to Off
Open the door .
Turn the water tap off.
Remove dishes, etc. when they have cooled down.
Notice:
When the appliance is already underway press the button "B" for 3 seconds, all of
the settings will be cancelled.
Interrupting the programme
Open the door. Caution! There is a risk of water squirting out from inside the appliance. Do not open
the door fully until spray arm has stopped rotating.
When you open the door, the dishwasher will beep ten times every thirty seconds.
If the appliance has already heated up or the hot water was switched ON and then the appliance door
opened, leave the door ajar for several minutes and then close. Otherwise, the appliance door may
open due to expansion.
When you close the door after interrupting the wash program there will be a delay of approximately 30
seconds before the dishwasher re-starts the wash cycle
Delayed start programming
You can delay the start of a programme in increments of 1 hour up to 24 hours.
Close the door after loading the appliance.
Switch dishwasher ON.
Immediately press the Delayed Start button “ F ”, the delayed start indicator “ E ” blinks, the remain-
ing time indicator “ G ” changes to “
”.
Press the Delayed Start button for 2 seconds until the numerical display show the required delay.
To cancel the time delay setting, pressing the Delayed Start button until the delayed start indicator
“ E” goes out.
Rotate programme knob “ J ” to select the desired programme.
C
E
A
H
B
D F
G
I
J
16
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
After 3 seconds the delayed start indicator “ E ” blinks, the time-remaining indicator “ G ” will blink and
decrease , the programme will start until the delayed start indicator “ G ” goes out .
Cancelling or modifying a cycle
A cycle that is underway can be modified if it has only been running for a short time. Otherwise, the
detergent may have already been used, and the appliance may have already drained the wash water.
If this is the case, the detergent dispenser must be refilled ( see the paragraph entitled, “ Loading the
detergent ”).
To modify a cycle that is already underway, follow the instructions contained in the paragraph entitled
"Reset drain function", and select the programme you wish (see the paragraph entitled, "Switching
the dishwasher ON").
1/2 Load Button
This button (see" Close-up View (Control Panel), letter " D ") makes it possible to wash dishes using only
the upper rack if there are not enough dishes for a full load. This will allow you to save on water and
energy consumption.
To select 1/2 load:
Press the 1/2 load button “ D ” , 1/2 load indicator “ C ” lights.
Select the programme ( see the paragraph entitled“ Switching the dishwaher ON”)
If the door is closed, after 3 seconds, the programme starts automatically.
- Please keep in mind that the amount of detergent should also be adapted to the 1/2 load.
- To cancel the 1/2 load, you can press the 1/2 load button “ D ” again ,until the 1/2 load indicators
“ C” goes out.
C
E
A
H
B
D F
G
I
J
Reset drain function
You can use Reset drain function to stop the washing cycle under running by Rotating the knob to
"Reset ", and the appliance will stop after a few minutes drain phase.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
How to keep your dishwasher in shape
EN
After Every Wash
After every wash, turn off the water supply the appliance and leave the door slightly ajar so that moisture
and odors are not trapped inside.
Remove the plug
Before cleaning or performing maintenance, always switch off the remove the plug from the socket. Do
not run risks.
No solvents or Abrasive Cleaning Products
To clean the exterior and rubber parts of the dishwasher, do not use solvents or abrasive cleaning
products. Rather, It is recommended that you use only a cloth and warm soapy water.
To remove spots or stains from the surface of the interior, use a cloth dampened with water and a little
white vinegar, or cleaning product made specifically for dishwashers.
Moving the Appliance
If the appliance must be moved, try to keep it in a vertical position. If absolutely necessary, it can be
positioned on its back.
Seals
One of the factors that cause odors to form in the dishwasher is food that remains trapped in the seals.
Periodic cleaning with a damp sponge will prevent this from occurring.
The door should not be left in the open position since this could present a tripping hazard.
When You Go on Holiday
When you go on holiday, it is recommended that you run a wash cycle with the dishwasher empty and
then remove the plug from the socket, turn off the water supply and leave the door of the appliance
slightly ajar. This will help the seals last longer and prevent odors from forming within the appliance.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and maintenance
EN
Regular inspection and maintenance of your appliance helps to prevent problems from occurring.This
saves time and aggravation.You should therefore carefully inspect the inside of your dishwasher from
time to time.
Overall condition of appliance
Check that no grease or scale has accumulated on the inside of the dishwasher.
If you discover any deposits:
Clean the interior of the dishwasher thorughly with a dishwasher detergent solution.
Dishwasher salt
H
I
Check the LOW SALT indicator “ I ”. Top up with salt, if
required.
Rinse-aid
Check the LOW RINSE AID indicator “ H ”, on the front
panel. Top up with rinse-aid,if required.
Filters
The filters “ 7”,“ 8” prevent larger particles of food in the
water from reaching the pump.These particles may occa-
sionally block the filters.
When the appliance has finished washing, check the fil-
ters for particles of food and, if required, clean.
After undoing the coarse micro-filter “ 7 ” , the filter unit
“8” can be removed. Remove any particles of food and
rinse the filters under running water.
7
Insert the filter unit “ 8 ” and tighten the coarse micro-
filter.
8
19
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Spray arms
Lime and remnants of food in the washing water can block the
nozzles in the spray arms “ 9 ” and “ 10 ” and the arm mountings.
Inspect the nozzles in the spray arms for blocked holes
due to remnants of food.
9
If necessary, pull the lower arm “ 10 ” upwards and lift it off.
Unscrew the upper spray arm “ 9 ”.
10
Clean both spray arms under running water.
Refit the spray arms. Ensure that the lower arm has locked
into place and the upper one is screwed tight.
Ensure that the power supply is turned off prior to removal
and cleaning of any internal pars.
Trouble Shooting
Resolving minor problems yourself
Experience has shown that you can resolve most problems that rise during normal daily usage yourself,
without having to call out a service engineer.Not only does this save costs,but it also means that the
appliance is available for use again that much sooner. The following list of common occurrences and
their remedies should help you identify the causes of most problems.
Problems...
...when the appliance is switched on
Appliance does not start up
Fault with fuse in mains electricity supply.
Plug not inserted in wall socket.
Appliance door not closed properly.
The ON/OFF button has not been pressed.
The program selector knob has not been turned to RESET and back to the selected program.
Approximately 30 seconds has not elapsed since door shut, power on and program selector rotated.
Water tap not turned on.
Blocked strainer in water intake hose.
- The strainer is situated in the Aquastop or supply-hose connection.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Caution
Do not forget that repairs should only be carried out by a qualified
specialist. Improper repairs can lead to considerable equipment dam-
age as well as danger to the user.
Error display on the time-remaining indicator
When the buzzer emits 10 short warning signal every 30 seconds and the time-remaining indicator
display "E1"
Have you checked whether:
the door is closed properly.
When the buzzer emits 10 short warning signal every 30 seconds and the time-remaining indicator
display "E3"
Have you checked whether:
the drain hose is too low.
When the buzzer emits 10 short warning signals every 30 seconds and the time-remain-
ing indicator display "E4"
Have you checked whether:
the drain hose is crimped or bent.
the drain hose is too high.
the food filters are blocked, please remove and clean the
filters.
When the buzzer emits 10 short warning signals every 30 seconds and the time-remain-
ing indicator display "E5"
Have you checked whether:
the water is turned on and the hose is connected properly;
the water supply to the house is on and has sufficient pressure;
the water supply hose is crimped or bent;
the filter for the water supply hose is clogged.
the drain hose is too low.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
When the buzzer emits 10 short warning signals every 30 seconds and the time remain-
ing indicator display "E2" or "E6", Contact the nearest authorized service center.
If you take all these checks and the dishwasher still does not function or your dish-
washer have any other error display, you can power the dishwasher OFF, and wait a few
minutes. You can power the dishwasher on, try it again , if the dishwasher still does not
function and/or the problem persists, contact the nearest authorised service center and
provide them with the following information:
the nature of the problem.
the model type number (Mod...) And the serial number (S/N...), which are indicated on the plate
located on the side of the inner part of the door.
Lower spray arm rotates with difficulty
Spray arm is blocked by small items or food remains.
Lid in detergent compartment cannot be closed
Detergent compartment has been overfilled.
Mechanism is clogged with remnants of detergent.
Remnants of detergent stuck inside dispenser
Compartment was damp when it was filled up with detergent. Compartment must be dry before
detergent is added.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Water remains inside appliance after programme has ended
Blockage or kind in drainage hose.
Pump is jammed.
Filters are blocked.
The programme is still running. Wait for the programme to end .
...during washing
Unusual amount of foam is creased
Normal washing up liquid has been poured into the rinse-aid container.
Remove any spilled rinse aid with a cloth as it could otherwise lead to excessive foaming during the
next washing cycle.
Appliance stops suddenly while washing is taking place
Cut off electricity supply to appliance.
Water supply has been interrupted.
Knocking sound can be heared while washing is taking place
A spray arm is knocking against the dishes inside the appliance.
Rattling sound can be heared while washing is taking place
Crockery has not been stacked properly inside the appliance.
Knocking sound coming from inlet valves
This is caused by the way the water pipes have been laid and it has no effect upon the way the
appliance functions. There is no remedy for this.
...with the dishes,cutlery, etc.
Remnants of food are stuck to the dishes, cutlery,etc.
Dishwasher was not loaded properly. Jets of water could not reach all parts of the dishes, ect.
Too many items in the rack.
Items in the rack were touching each other.
Not enough detergent was added to dispenser.
Selected wash programme was not intensive enough.
Rotation of spray arm was obstructed by dishes, etc.
N ozzles in spray arm are blokcked by remnants of food.
Filters are blocked.
Filters have been incorrectly fitted.
Waste-water pump is jammed.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Plastic items are discoloured
Not enough detergent was added to dispenser.
Detergent has insuffcient bleaching properties. Use a detergent containing a chemical bleaching agent.
White stains are left on crockery, glasses have a milky appearance
Not enough detergent was added to dispenser compartment.
Amount of rinse-aid was set too low.
Although water is quite hard, no salt has been put in appliance.
Water softener was set too low.
Lid on salt container is not screwed tight.
If you used a phosphate-free detergent , try a detergent containing phosphates and compare results.
Dishes,cultlery,etc.have not been dried
Selected programme did not include drying function.
Amount of rinse-aid was set too low.
Items were removed from dishwasher too soon.
Glasses have a dull appearance
Amount of rinse-aid was set too low.
Tea stains or traces of lipstick have not been completely removed
Detergent does not have a sufficient bleaching effect.
Washing temperature was set too low.
Traces of rust on cutlery
Cutlery is not sufficiently rustproof.
Salt content in washing water is too high.
- Lid on salt container is not screwed tight.
- Too much salt was spilt while filling container.
Glasses become clouded and discoloured; coating cannot be wiped off
Unsuitable detergent was used.
Glasses are not dishwasher-proof.
Smears left behind on glasses and cutlery; glasses have acquired a metallic appearance
Amount of rinse-aid set too high.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Technical data
60 cm
60 cm
Width
Depth
Height
85 cm
Capacity
12 standard place settings
Mains water pressure
Power voltage
Fuse
0.03-1.0Mpa
220-240V~50Hz
13A
1950W
Total absorbed power
Important information
Notes on waste disposal
Old appliances still have some residual value. An environment-friendly method of disposal will ensure
that valuable raw materials can be recovered and used again.
When an appliance has reached the end of its working life,unplug it from the mains.Cut through the
mains cable and dispose of it together with the plug.
Destroy the door locking mechanism. This will ensure that children at play cannot become locked inside
and are not exposed to the risk of suffocation.
Your new appliance was protected by suitable packaging while it was on its way to you. All materials
used for this purpose are environment-friendly and can be recycled. Please make a contribution to
protecting the environment by disposing of the packaging appropriately.
Do not allow children to play with any parts of the packaging. There is a risk of suffocation by the
cardboard boxes and the plastic wrapping.
Up-to -date information concerning options for disposal can obtained from your retailer or local munici-
pal administration.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
General information
Measures must be taken to ensure that built-under and built-in units that are subsequently re-sited
as free-standing appliances cannot topple over. This can be achieved by bolting the dishwasher to
the wall or fitting it under a continuous work surface which is screwed to the adjacent cupboards.
Information on comparability tests implemented in compliance with
EN 50242
Appliance loaded in accordance with standard specifications.
Example of loaded dishwasher: See fig. 1 , 2.
Capacity: 12 place settings
Comparability programme: Light wash
Rinse-aid setting: 5
Detergent: 5g+25g
Fig.1
Fig.2
Height-adjustable top-basket must be inserted in the uppermost position.
If the comparability tests do not comply fully with EN 50242, e.g., degree of soiling, type of dishes and
cutlery, etc., contact the appliance manufacturer before starting the test.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|