Haier Clothes Dryer HDY D70 F User Manual

Name of Parts

Program selector

Condenser Tumble Dryer

HDY-D70-F

Container handle

Door

Table of Contents

Before using the dryer

Name of Parts....................................1

Important Safety Instructions .....2-3

Installation.....................................4-6

Preparation ......................................7

Plinth

Earth terminal

Back plate

How to operate the dryer

Power supply cable

Control panel.................................8-9

Programming guide.........................10

Drying methods ...............................11

Back cover board

Maintenance

Rear footplate

Cleaning and maintenance .......12-13

Trouble shooting .......................14-15

Drainage outlet

Wiring circuit ..................................16

Specifications .................................17

Warning

Read all instructions before using dryer.

Dryers are provided with operating,care and in-

stallations instructions

SAVE THESE INSTRUCTIONS

This diagram may be slightly different from the layout of the machine you have just

purchased due to techincal improvements

Download from Www.Somanuals.com. All Manuals Search And Download.

Installtion

Dimensions

Change the door-opening direction

If the direction of the dryer's door is not suitable to the location, its opening direction

may be changed. The procedure is as follows:

a = 855 mm

b = 620 mm

c = 595 mm

Weight = 43 kg

1. Unscrew the 4 hinge screws holding the door onto the machine and remove

the door.

2. Unscrew the door catch 6 and prise out the catch cover on the opposite side

of the door and transpose them.

3. Unscrew the door hinges and prise out the hinge covers on the opposite side

of the door and transpose them.

4. Remove the 4 blanking plugs from the screw holes on the machine and insert

them in the holes on the other side.

Packing accessories

Checklist of the accessories and materials provided with the machine:

5. Refit the door on the opposite side of the machine.

Owner's

manual

Certificate of

Conformity

Name

Drainpipe

Quantity

To ensure the dryer operates normally, attention must be paid to the

following instructions;

■The dryer must be level when installed. Its bottom is equipped with

adjustable feet. Adjust these 4 feets to level the unit before operation；

■ Check whether there is any damage to the dryer during transportation.

Any damaged dryer must not be used. if the unit is damaged, contact

your dryer supplier;

d e

■ The dryer must be kept away from flammable substances；

■ The surrounding environment must be dry and ventilated;

■ To allow the dryer to perform better, the ambient temperature shall not be

lower than 10

℃

nor higher than 35℃.

a-door hinge b-catch cover c-door

d-hinge cover e-door catch f-blanking plug

Download from Www.Somanuals.com. All Manuals Search And Download.

Preparation

Installtion

Drain switchover

Attention

■ Before use, clean any deposits from inside the drum of the dryer with

a wet towel;

■Clean debris on the filter screen to increase the drying efficiency.

During the drying of the laundry, the condensate water is automatically

collected in the box inside the machine, so that the water needs to

be removed from the box after every drying cycle. If your

dryer is in the vicinity of a drain, you may allow the condensed

water to discharge directly into the drain through the drainpipe

provided to avoid emptying the box every time.

The method to connect the drainpipe is as follows:

1. Loosen the hose clip with the drain switchover joint;

2. Pull the hose off the joint;

Turning on power

Before turning on the power for the dryer, check:

■Whether the supply voltage is in accordance with the value indicated on the

nameplate;

■Whether the supply receptacle can withstand the maximum power load to

■

the dryer;

■Whether the supply receptacle is in accordance with the plug of the dryer.

■

3. Install the accessory drainpipe on the joint;

4. Fix the hose in place with the clip;

If not, replace the power supply cable or receptacle to make them accord

with each other; The replacement of the power supply cable must be

made by a qualified professional or our authorized service agent;

■The dryer must be grounded securely.

Note: The outlet of the drainpipe must not be higher than 1.0 m above

the floor

Treatment of laundry to dry

■

Check whether the laundry to be dried is suitable to be dried in the dryer;

■The dryer can only dry the laundry that has been spun dry. Do not put too

wet laundry into the machine;

■Empty all pockets of the laundry with such items as keys and coins and

remove the adornment that is not suitable to be dried;

■Pull up zippers, sew and mend up loosened fasteners and tie up

dispersed ribbons to prevent the laundry from being entangled. If

necessary, put small items into a net.

■To achieve a better drying result, shake the heavy laundry and make it loose

before load it into the dryer.

Load to dry

Make sure that the laundry you are going to dry is suitable for drying in a

dryer.You will find information on this on the laundry labels.The following

symbols mean:

Drying in the

tumble dryer

not possible

Dry at normal

temperature

Dry at

reduced temperature

Warning: Do not dry wool, silk, down and other delicate fabrics to avoid

damage to fabrics.

Download from Www.Somanuals.com. All Manuals Search And Download.

Control Panel

G - Programme progress display

Depending on the programme selected, the drying stage reached is

shown by the indicator lamps on the control panel:

- Drying

Séchage

- Ready to iron

- Airing

Air frais

repasser

Anti-froissage

- End/Anti-crease

At the end of a programme,the End/Anti-crease indicator lamp comes on.

The drum will continue to rotate at intervals to prevent laundry creasing, if you

do not wish to remove it immediately.

A - Program knob

Turn this knob to choose the drying program you desire. This type of dryer

has 11 program options . For description of specific programs, refer to the list of

programs on Page 10. When the drying program is selected,the relevant indicator

light is on.

H - LED screen

The screen displays the remaining time for a program, the delay time and

other related information.

Note: The remaining time to start a program is the default time for the

program. During operation, with variation of factors such as the moisture

content. The actual remaining time will be automatically adjusted until the preset

drying result has been achieved and the program is complete.

B - Start/Pause button

Gently touch this button to start the dryer. Gently touch this button again

during the operation of the dryer and the indicator light and display screen will

flash and the machine will be paused .Press the button again and the program

will continue .

I - Maintenance displays

C - Signal button

Bac plein

- Empty tank

When the drying cycle has finished, an intermittent acoustic signal will

sound.Touch this button,the buzzer will be canceled.

Filtre

- Clean filter

Condenseur

- Clean condenser

Important: After each drying cycle，

– Clean the filter；

– Drain the condensed water container；

(See section “Cleaning and maintenance”)

D- Anti-crease button

If this additional function is selected, the anti-crease phase at the end of

the drying cycle is lengthened by 60 minutes. The laundry can be removed

at any time during the anti-crease phase.

J -

E - Delicate button

During a program, the drying temperature and power will decrease and the

drying time will increase to take better care of the delicate laundry.

D+E composite button and child lock function

F- Delay button

During a program, press and hold down both buttons for 3 seconds to

set up the child lock function if necessary. At this time, The display screen

shows the remaining time and the lock alternatively, and the control panel will

lock. Press and hold down both buttons for 3 seconds once again and the child

lock will release.When the program is end or the power off during the program,

the child lock will release.

Gently touch this button before a program starts. You may choose to start

the dryer after a preset time. The delay range is between 1 and 19 hours.

Every touch of the delay button will increment by one hour. When you pass 19

hours, the delay time will turn off. After a delay time is set, gently touch the

Start/Pause button to the start the delay operation and the indicator light will

flash.

Download from Www.Somanuals.com. All Manuals Search And Download.

Programming Guide

Drying Methods

Type of Laundry

1.Turning on power

Max. load

Program

Degree of drying

Insert the power plug into an appropriate wall socket and turn on the power.

Operating power supply: (220-240)V/50Hz.

COTTON

Heavy cotton fabrics, sheets,

gowns.

Extra dry

Ready to wear

Ready to iron

Damp

7 kg

^Sec*

2. Laundry loading

Open the door and place the

laundry into the drum of the dryer

To save energy and achieve a better

drying result, please spin the laundry as

dry as possible. Place the laundry evenly

into the drum after shaking them loose.

Note: Do not put excess laundry into

the dryer to avoid damage to the dryer

and laundry.

Reference weight of fabrics for drying

Prêt à

ranger

●Jeans (appr 800

)

●

Overalls

(cotton appr 950g)

7 kg

Cotton fabrics, sheets, coats

Ordinary cotton fabrics

●Pajamas

●Blended fabric

clothes

(appr 800g)

(appr 200g)

Prêt à

repasser

●Shirts

(appr 300g)

●

T-shirt

(appr 300g)

Underwear

●

( appr 70g)

Humide

●Socks

(blended fabrics

appr 50g)

●Jackets (cotton

appr 800g)

●Single bed sheets

(cotton appr 800g)

●Woolen blankets

(appr 3000g)

SYNTHETIC

3. Setting drying program

Turn the program knob to set an optimal drying program according to the

laundry type and the drying result required.

Prêt à

ranger

3 kg

Ready to wear

Ready to iron

Ordinary synthetic fabrics

Prêt à

repasser

4. Selecting additional functions

According to you desire, select the additional function:

- Start Delay,- Deliacate,- Anti-crease,- Signal Off.

TIMER

Timer 20 min

Timer 40 min

7 kg

20 min

40 min

60 min

Heavy fabrics, needing

further drying.

5. Program operation

After a program is set, gently touch the Start/Pause button to start the

program

Timer 60 min

6. Program completion

Before the drying program ends, the dryer will enter the cold air cycle.

After the program is complete, the display screen will display "End." Open

SPECIAL PROGRAMS

Coup de

Refresh/Airing

One piece

7 kg

the door to remove the laundry.If the laundry is not removed after the drying

frais

program is complete,the dryer will start the anti-crease protection cycle

automatically.In the anti-crease protection cycle, the dryer's drum will run at

a set interval to keep your laundry loose.

Délicat

0.5 kg

* Programme setting for testing in accordance with EN 61121.

7. Turning off the dryer

Press the power keystoke to cut off the power supply and turn off the dryer

at the wall socket.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and Maintenance

1.Cleaning the surface

-Using a coin or other tool, push the slides on the cover to the position

as shown in the figure and then remove the cover;

-Turn the condenser's handle 90 degrees in the direction as shown in

the figure;

Wipe the body of the dryer and the control panel with a damp cloth.

Remember not use any organic solvent or corrosive agent to avoid

damage to the machine.

-Remove the condenser from the dryer;

2. Cleaning the filter screen

-Clean the condenser with a brush or flush with by a water jet;

Note: Do not use a sharp tool in cleaning the heat exchanger, otherwise

it may damage its sealing performance;

-Put the condenser back in place and lock up the cover;

-Put the lower deco panel back in place.

To ensure a good ventilation during drying,

the filter screen must be cleaned after every

drying program is complete.

Open the door and remove the filter screen

from the machine. Open the screen and clean

off the dust on the screen with a wet towel. After

cleaning, put the screen back in place.

3. Emptying the water collection box

During operation , steam condenses into

water and is collected in the box.The box must

be emptied after the program is complete.

-Hold the handle and pull the box outwards to

remove it. keep it level to prevent the water

from overflowing;

5. Cleaning the drum

-Pour away water. Note: the

After the dryer has operated for

a time, fabric caring agents or

calcium contained in the water will

form an almost invisible layer on

the inside of the drum.

This makes the dryer not able to

reliably and accurately identify the

dryness of the laundry. So the inside

of the drum, especially the stainless

steel pieces on the blades must be

cleaned regularly by a wet cloth.

water can not be used for drink or for food

processing;

-Put the box back in place.If the box has not

been emptied, the dryer will sound an alarm

when the box is full. The indicator light comes

on while the box is emptied and the dryer will

stop. It will not restart until the box is emptied.

4.Cleaning the condenser

The condenser must be cleaned monthly.

Switch off the power supply before cleaning.

-Hold the protrusions on both sides of the

lower deco panel and open it.

Download from Www.Somanuals.com. All Manuals Search And Download.

Trouble Shooting

Prompt and Alarm Information

The following must be confirmed before calling for service:

In case of an improper operation or trouble with the machine when it

operates, the code corresponding to the trouble will be displayed on the

screen:

Problem

Possible Cause

Cause

Code