Important Safety Precautions
When using this product, the safety precautions below must be taken
to offset possible legal liabilities and damages.
ELECTRICAL SAFETY
This product is intended for use when supplied with power from
the battery. Other usage may be dangerous and will invalidate any
approval given to this product.
SAFETY IN AIRCRAFTS
Due to the possible interference caused by this product to an aircraft's
navigation system and its communications network, using this product
on board an airplane is against the law in most countries.
ENVIRONMENT RESTRICTIONS
Do not use this product at gas or refueling stations. The use of this
product is also prohibited in fuel storehouses, chemical plants, and
locations containing explosives.
SAFETY FOR ENVIRONMENTS
Do not use this product in gas stations, fuel depots, chemical plants or
where blasting operations are in progress, or in potentially explosive
atmospheres such as fuelling areas, below deck on boats, fuel or
chemical transfer or storage facilities, and areas where the air contains
chemicals or particles, such as grain, dust, or metal powders. Please
be aware that Sparks in such areas could cause an explosion or fire
resulting in bodily injury or even death.
ROAD SAFETY
Vehicle drivers in motion are not permitted to use telephony services
with handheld devices, except in the case of emergency. In some
countries, using hand-free devices as an alternative is allowed.
INTERFERENCE WITH MEDICAL EQUIPMENT FUNCTIONS
This product may cause medical equipment to malfunction. The use of
this device is forbidden in most hospitals and medical clinics.
| 3
Download from Www.Somanuals.com. All Manuals Search And Download.
NONIONIZING RADIATION
This product should be operated in the suggested normal condition
only to ensure the radiative performance and safety of the interference.
As with other mobile radio transmitting equipment, users are advised
that for satisfactory operation of the equipment and for the safety
of personnel, it is recommended that no part of the human body be
allowed to come too close to the antenna during operation of the
equipment.
4 |
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
| 5
Download from Www.Somanuals.com. All Manuals Search And Download.
6 |
Download from Www.Somanuals.com. All Manuals Search And Download.
| 7
Download from Www.Somanuals.com. All Manuals Search And Download.
8 |
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Getting Started
1.6 Using the Start Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
1.1 Getting to Know your Device and
its Accessories
Front, top, and left-side view
1
2
3
4
5
6
7
15
14
8
9
10
11
12
13
No.
Item
Function
1
2
MiniSD Card Slot Lets you insert a storage card (miniSD) for storing data.
POWER Button
Press to turn off your device temporarily and switch the
device to sleep mode; press and hold (about five seconds)
to turn off your device completely.
When your device is in sleep mode, you can still use
the phone function to receive calls; however, the phone
function is off when you turn off the device completely.
10 | Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Notification
LED 1
Bi-color LED on the left side: Blue for Bluetooth system
notification of powered-up and ready to transmit radio
frequency signal, and Green for Wi-Fi status.
- Blinking Blue indicates the device is in Bluetooth-
enabled mode.
- Blinking Green indicates the device is in Wi-Fi-enabled
mode.
Please note that Bluetooth and Wi-Fi features can
coexist on your device. If the two features are enabled
simultaneously, the LED will blink Blue and Green
alternately.
4
5
Speaker
Notification
LED 2
Listen to audio or a phone call from here.
Bi-color LED on the right side: Green and Red for GSM
standby, SMS message, GSM network status, notification,
battery charging status.
- Blinking Green indicates the device connects to the
GSM network.
- Glowing Green indicates the battery is fully charged
(using the AC adapter).
- Blinking Red indicates the battery is low.
- Glowing Red indicates the device is in LDO charging
mode (the battery is empty).
- Blinking Amber (Green + Red) indicates there is
notification from the system.
- Glowing Amber (Green + Red) indicates the battery is
under charging by connecting the AC adapter.
6
7
8
9
Internet Explorer Press to launch Internet Explorer.
Messaging
Launches the outlook (email) application.
Use to write, draw, or make a selection with the stylus.
Performs the command shown in the label shown on the
Display Screen above the button.
Touch Screen
Left SOFT KEY
10 Right SOFT KEY
Performs the command shown in the label shown on the
Display Screen above the button.
11 END Button
12 NAVIGATION
control
Press to end a call.
Press this multi-directional control up, down, left, or right
to move through menus, program instructions; carry out
the selection by pressing the center button.
Press to answer an incoming call or dial a number.
Press up or down to adjust the volume. To adjust the
conversation phone volume, you must do it during a call.
Adjusting the volume at another time will affect the ring,
notification, and MP3 sound levels.
13 TALK Button
14 Volume
Controller
15 Comm Manager
Press to start Comm manager; press and hold to switch to
vibration mode.
Getting Started | 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Back, bottom, and right-side view
1
2
9
3
4
10
11
12
5
6
7
8
12 | Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
No.
1
Item
Function
Car Antenna
Connector
You can connect your phone to a car antenna to utilize
the superior reception quality. Car antenna must be
purchased separately.
2
3
4
5
6
7
8
9
Flash
Allows you to capture images even in a dark
environment.
Self-Portrait Mirror Position your device until this mirror reflects the image
you want to capture.
Camera Lens
The “live” incoming video stream enters through this
lens, when Camera mode is active.
Stylus and Stylus
Slot
Use the stylus to write, draw, or select items on the
touch screen.
Microphone
Speak into the microphone when receiving or making a
phone call or voice recording.
Sync Connector
Earphone Jack
Voice Command
Use this connector for synchronizing data or recharging
the battery.
Allows you to listen to audio or use the phone’s hand’s-
free kit.
Press to start Voice Speed Dial; press and hold to
record a voice note.
10 Infrared Port
Let you exchange file(s) or data with other devices
wirelessly.
11 RESET Button
12 CAMERA Button
With the stylus, press the RESET button to soft-reset
your device.
Press to launch the camera. Press again when in
camera mode to take a picture or record a video clip.
Getting Started | 13
Download from Www.Somanuals.com. All Manuals Search And Download.
The QWERTY keyboard
Your device provides you with a QWERTY keyboard, which is similar to
a standard keyboard on your PC. To use the QWERTY keyboard, slide
the screen panel to the right to reveal the keyboard.
The QWERTY keyboard
You can do the following with the QWERTY keyboard:
•
To type lowercase letters, press the keys using your thumbs or
fingers.
•
•
To use all uppercase letters, press
first, then
.
To type a single uppercase letter, press
corresponding key.
and then press the
•
•
To enter a number or symbol, press
corresponding key.
and then press the
Press the Left/Right SOFT KEY
shown in the label above the key.
to perform the command
•
•
•
Press
Press
to verify your data entries or exit the program in use.
to open the Start menu.
Press the arrow keys
movement.
/
/
/
for directional
14 | Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
The following accessories are provided with the device:
1
2
3
No.
1
Item
AC adapter
USB cable
Function
Recharge the device battery.
2
Connect your device to a PC and synchronize data.
3
Stereo headset
with volume
control
Provides a volume control jog dial and a Send/End
button. You can use the button to pick up and hang
up incoming and outgoing calls. Plug into Earphone
Jack to listen to audio files.
Getting Started | 15
Download from Www.Somanuals.com. All Manuals Search And Download.
1.2 Installing the SIM Card
Follow these steps to install a GSM SIM (Subscriber Identity Module)
card provided by your local Cingular Wireless representative. The SIM
card contains your phone number, service details, and phonebook/
message memory.
Your device supports both 1.8V and 3V SIM cards. Some legacy SIM
cards will not function within this device. The customer should consult
with their service provider for a replacement SIM card. There may be a
fees for this service
1. Make sure your device is turned off.
2. Remove the battery cover.
3. Pull the plastic ribbon to remove the battery. Then, insert the SIM
card into the SIM card slot with its gold contacts facing down (the
cut-off corner of the SIM card should match the cut-off corner in
the slot).
4. Replace the battery and gently push down to snap it into place.
5. Replace the battery cover.
16 | Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3 Battery Information
Your device contains a rechargeable Li-ion polymer battery. Your
device is designed to use only manufacturer-specified original batteries
and accessories. Battery performance depends on many factors,
including your wireless service provider’s network configuration, signal
strength, the temperature of the environment in which you operate your
device, the features and/or settings you select and use, items attached
to your device’s connecting ports, and your voice, data, and other
program usage patterns.
Battery life estimates (approximations):
•
•
Standby time: 150 ~ 200 hours
Talk time (Screen off): 3.5 ~ 5 hours
Warning! To reduce risk of fire or burns.
• Do not attempt to open, disassemble, or service the battery pack.
• Do not crush, puncture, short external contacts, or dispose of in fire
or water.
• Do not expose to temperatures above 60oC (140oF).
• Replace only with the battery pack designated for this product.
• Recycle or dispose of used battery as stipulated by local regulation.
To check the battery power
•
Tap the battery level icon (
Today screen.
) on the
•
Tap Start > Settings > System tab >
Power.
Getting Started | 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Charge the battery
New batteries are shipped partially charged. Before you can use your
device, you need to install and charge the battery. Some batteries
perform best after several full charge/discharge cycles. You can charge
the battery by:
•
•
Connecting your device directly to an external power source.
Plugging the device sync cable into the USB port on your PC.
Low battery
When the low-battery warning appears, do the following:
•
•
•
Immediately save your current data.
Synchronize with your PC to charge the battery.
Turn off your device.
1.4 Starting Up
Turn the device on and off
To turn on the device, press the POWER button. When you turn on
the device for the first time, you are asked to complete a calibration
process. For more information, see “Calibrate the device” on next
page.
To turn off the device, press POWER again.
Note
Pressing POWER turns off your device temporarily and switches the
device to sleep mode. However, you can still receive messages and
calls while your device is in the sleep mode.
18 | Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Calibrate the Device
Calibrating the device screen involves tapping with the stylus the
center of a cross as it moves around the screen. This process ensures
that when you tap the screen with your stylus, the tapped item is
activated.
If your device does not accurately respond to screen taps, follow these
steps to re-calibrate it:
1. Tap Start > Settings > System tab > Screen.
2. On the General tab, tap Align Screen, and follow the instructions
on the screen.
Buttons Lock
It is possible to lock the buttons on the device, so that the applications
may not be accidentally launched. Once you enable this feature, only
the Power button can turn on your device.
To configure the Buttons Lock settings
•
Tap Start > Settings > Personal tab > Buttons. On the Lock
tab, select the Lock all buttons except Power button check
box.
Getting Started | 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Manage screen settings
The device touch screen has three orientation modes: Portrait,
Landscape (right-handed), and Landscape (left-handed). Portrait
mode allows you to get a better view or a better operation of certain
programs on your device, while Landscape mode may be optimal for
viewing longer text files.
•
To change the orientation, tap Start > Settings > System tab >
Screen, and select the orientation you want.
Portrait mode
Landscape mode
•
•
To smooth the edges of screen fonts for many programs, on the
ClearType tab, select the Enable ClearType check box.
To increase the readability or to see more content on the screen,
on the Text Size tab, adjust the text size by moving the slider.
Note
When you slide the display panel to open the QWERTY keyboard, the
screen orientation changes automatically.
20 | Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 The Today Screen
The Today screen displays important information, such as upcoming
appointments and status indicators. You can tap a section on the
screen to open the associated program.
•
•
To access the Today screen, tap Start > Today.
To customize the Today screen display, including the background
image, tap Start > Settings > Personal tab > Today.
1
2
3
Tap to open the Start menu.
Tap to view connectivity status.
Indicates the radio signal strength.
Tap to configuration the phone
settings.
1
2 3 4 5
4
5
Tap to control device/ringer
volume level.
6
7
Displays the current time. Tap and
hold to change the clock mode:
Analog or Digital.
8
6
Displays the current date. Tap to
setup date, time, alarm, and more.
9
10
7
8
Tap to set owner information.
Your day at a glance with
reminders. Tap to open the related
program: messages, tasks, and
appointments.
11
12
9
Tap to open MSN sign-in screen.
10 Tap to lock or unlock the device.
: locked; : unlocked.
13
14
11 Indicates the battery status. Tap to
open the Power Settings screen.
12 Tap to start Comm Manager.
13 Tap to open the Calendar screen.
14 Tap to open the Contacts screen.
Getting Started | 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Indicators
Following are some of the status icons that you may see on your
device.
Icon
Description
Indicates the battery is fully charged.
Indicates the battery is very low.
Battery charging.
Sound on.
Sound off.
Ringer in vibration mode.
Connection is active.
Connection is not active.
Synchronization in progress.
Synchronization error.
Indicates maximum signal strength.
No signal.
Phone is turned off.
No phone service.
Searching for phone service.
Voice call in progress.
Calls are forwarded.
Call on hold.
Missed call.
GPRS/EDGE available
22 | Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Icon
Description
New e-mail or text messages.
New voice mail
There are more notifications. Tap the icon to view all.
Indicates Wi-Fi is turned on.
Indicates the device is locked.
: Wi-Fi off.
: Device unlocked.
1.6 Using the Start Menu
The Start menu, located at the top left corner of the Today screen,
displays a list of programs. It lets you close a screen and switch from
one program to another. You can start a program by scrolling through
the programs list and then pressing ENTER, or by tapping a program
with the stylus.
1
2
Tap to open the Today screen.
1
2
Tap to start a program. The items
displayed in Start menu can be
customized by tapping Start
> Settings > Personal tab >
Menus.
3
4
Tap to start a recently-used
program.
3
Tap to view and select more
programs that are installed in your
device.
4
5
6
5
6
Tap to change device settings.
Tap to see a Help topic for the
current screen.
Getting Started | 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Program Indicators
Following are some of the icons for the programs that are already
installed on your device.
Icon
Description
ActiveSync Synchronizes information between your device and a
PC.
Calculator Performs basic arithmetic and calculations, such as
addition, subtraction, multiplication, and division.
Calendar Keeps track of your appointments and creates meeting
requests.
Camera Snaps photos or shoots video clips with accompanying
audio.
ClearVue PDF enables you to view PDF files on your Pocket PC.
Comm Manager Allows you to manage the device’s connection
(including Wi-Fi, Bluetooth, and ActiveSync), and switch the ringer/
vibration mode.
Contacts Keeps track of your friends and colleagues.
Download Agent Provides information about the download status
and the downloaded content from the Internet.
Excel Mobile Creates new workbooks or lets you view and edit
Excel workbooks.
File Explorer Enables you to organize and manage files on your
device.
Games Lets you play two pre-installed games: Bubble Breaker
and Solitaire.
Help Enables you to see Help topics for a program on your device.
Internet Explorer Internet Explorer Mobile browses Web and WAP
sites, and downloads new programs and files from the Internet.
JAVA Enables you to download and install Java applications, such
as games and tools, on your device.
24 | Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Icon
Description
Messaging Sends and receives e-mail and text messages.
Modem Link Allows you to use your device as a modem.
Notes Creates handwritten or typed notes, drawings, and
recordings.
Phone Makes and receives calls, switches between calls and sets
up conference calling.
Pictures & Videos Collects, organizes, and sorts picture and video
files in the My Pictures folder of your device or on a storage card.
Pocket MSN Sends and receives instant messages with your MSN
Messenger contacts.
PowerPoint Mobile Lets you view and edit PowerPoint slides and
presentations.
Search Enables you to search contacts, data, and other information
on your device.
SIM Manager Collects, organizes and sorts the contact list stored
in your SIM card.
Tasks Keeps track of your tasks.
Windows Media Enables the multimedia function on your device.
Voice Speed Dial You can record voice tags so that you can dial a
phone number or launch programs simply by speaking a word.
Word Mobile Create new documents or lets you view and edit
Word documents.
Terminal Services Client Allows you to log on to a PC running
Terminal Services or Remote Desktop, and use all of the programs
available on that PC from your mobile device.
Zip Enables you to save memory and increase the storage capacity
of your device by compressing files in the conventional ZIP format.
Getting Started | 25
Download from Www.Somanuals.com. All Manuals Search And Download.
26 | Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Entering and Searching Information
2.6 Using Phone Pad
2.7 Drawing and Writing on the Screen
2.8 Recording a Note
2.9 Searching Information
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1 Introduction
When you start a program or select a field that requires text or
numbers, Input Panel automatically becomes available. Input Panel
provides access to the various input methods available on your device,
including Block Recognizer, Keyboard, Letter Recognizer, Phone
Pad, and Transcriber. By default, the Input Panel icon appears on
the menu bar to indicate which input method is currently selected. The
Input Selector arrow (shown at the right side of the Input Panel icon)
opens a list of available input methods.
To show or hide Input Panel
•
Tap the Input Panel icon on the menu bar.
Example:
Input Panel (Keyboard)
Input Selector arrow
Input Panel icon
Icon
Input method
The on-screen keyboard.
Letter Recognizer or Block Recognizer.
Phone Pad
Transcriber
28 | Entering and Searching Information
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2 Using the Keyboard
To enter text, symbols, and numbers, you can either type using the
QWERTY Keyboard or the standard on-screen Keyboard. For use of
the QWERTY keyboard, see the instruction in Chapter 1.
Using the standard on-screen Keyboard
The on-screen Keyboard is available when text entry is possible. You
can enter text by tapping keys on the keyboard that are displayed on
the screen.
To enter text using the on-screen Keyboard
1. In a program, tap the Input Selector arrow, and tap Keyboard.
2. Enter text by tapping keys on the on-screen Keyboard.
To enlarge the on-screen Keyboard
1. Tap the Input Selector arrow, then tap Options.
2. In the Input method list, select Keyboard.
3. Tap Large Keys.
Entering and Searching Information | 29
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 Using Letter Recognizer
With Letter Recognizer, you can write individual letters, numbers, and
punctuation, which are then converted into typed text.
To use Letter Recognizer
1. From a program, tap the Input Selector arrow, and tap Letter
Recognizer.
2. Write characters, numbers, and symbols in the designated writing
area.
•
•
Enter capital letters by writing in the ABC (left) area of the box.
Enter lower case letters by writing in the abc (middle) area of
the box.
•
•
Enter numbers by writing in the 123 (right) area of the box.
Enter punctuation and symbols by tapping in either area of the
box and then writing the desired character.
Note
Tip
Letter Recognizer is available when text entry is possible.
For help with writing characters with Letter Recognizer, tap the
question mark near the writing area.
30 | Entering and Searching Information
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4 Using Block Recognizer
With Block Recognizer, you use a single stroke to write letters,
numbers, symbols, and punctuation, which are then converted into
typed text.
To use Block Recognizer
1. From a program, tap the Input Selector arrow, and tap Block
Recognizer.
2. Write characters, numbers, and symbols in the designated writing
area.
•
•
•
Enter letters by writing in the abc (left) area of the box.
Enter numbers by writing in the 123 (right) area of the box.
Enter symbols and punctuation by tapping in either area of the
box and then writing the desired character.
Note
Tip
Block Recognizer is available when text entry is possible.
For help with writing characters with Block Recognizer, tap the
question mark near the writing area.
Entering and Searching Information | 31
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5 Using Transcriber
Transcriber is a handwriting recognition program that allows you to
write in cursive, print, or a combination of both. Transcriber works
transparently in the background of programs, recognizing words with
its integrated dictionary. When Transcriber is turned on, it interprets
stylus movement anywhere on the screen as handwriting input. For
more information about using Transcriber, see Help on your device.
To start Transcriber
1. Start a program that accepts user input, such as Word Mobile.
2. Tap the Input Selector arrow, and tap Transcriber. The
Transcriber introductory screen appears.
To write using Transcriber
1. In a program, position the cursor where you want text to appear.
2. Use the stylus to write anywhere on the screen. The handwriting
will be converted to text shortly after you lift the stylus from the
screen.
To enter punctuation and symbols
Transcriber comes with an on-screen keyboard that provides an easy
way to add punctuation or a special symbol to existing text.
•
From a program, tap
on the Transcriber toolbar.
The keyboard remains visible until you tap the button again.
Tips
To reposition the keyboard, tap and hold the title bar, then drag to the
desired location.
When no text is selected, you can also open the keyboard by doing
the gesture.
32 | Entering and Searching Information
Download from Www.Somanuals.com. All Manuals Search And Download.
To edit text
1. In a program, draw a line across the text you want to edit.
2. After you lift the stylus from the screen, the line will disappear and
the selected text will be highlighted.
3. Do either of the following:
•
•
Rewrite the text.
Use gestures to capitalize letters, insert a space, and so
on. For information about using gestures, see “Transcriber
Gestures” in this chapter.
Transcriber Gestures
Use quick strokes of the stylus to edit your text or to insert returns,
spaces, or tabs.
Do
To
Insert a paragraph return at the cursor.
The horizontal portion of the gesture must be at least two times
longer than the vertical portion.
Insert a space at the cursor.
The horizontal portion of the gesture must be at least two times
longer than the vertical portion.
Move the cursor one space back and erase any text.
Do the gesture by drawing a line from right to left.
Open the menu of alternate words if a word is selected or the on-
screen Transcriber keyboard if no text is selected.
Do the gesture by drawing a line straight down and back up.
Change the capitalization of a selected letter, word, or block of
text.
Do the gesture by drawing a line straight up.
Entering and Searching Information | 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Do
To
Undo the last action.
Do the gesture by drawing a line straight up and back down.
Copy the selected text.
Do the gesture by drawing a line from left to right and back.
Cut the selected text.
Do the gesture by drawing a line from right to left and back.
Paste copied or cut text.
Do the gesture by drawing a line from the lower left of the screen
diagonally up toward the right and back down to the right.
Insert a tab.
The horizontal portion of the gesture must be at least two times
longer than the vertical portion.
Tip
You can also use the Enter, Space, and Backspace buttons on the
Transcriber toolbar.
The Transcriber toolbar
The Transcriber toolbar, which appears at the bottom of the screen
when Transcriber is open, provides easy access to several tools, Enter,
Space, and Backspace buttons, and Left and Right arrow buttons.
Tap
To
Open the Options dialog box, where you can set options such as
writing direction, text entry, and shorthand.
Open Letter Shapes, where you can set your personal writing
styles to maximize recognition.
Use the miniature keyboard to quickly enter numbers, punctuation,
and
other symbols.
34 | Entering and Searching Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Tap
To
Change the character recognition mode.
•
•
•
a mode. This is the default for optimum handwriting
recognition.
123 mode. Numbers and some letters are allowed and the
calculator is activated.
A mode. All letters are automatically capitalized.
If you are in A or 123 mode, recognition returns automatically to
the default mode once you lift the stylus.
Insert a space at the cursor.
Insert a paragraph return at the cursor.
Move the cursor one space to the left.
Move the cursor one space to the right.
Move the cursor one space back and erase any text.
Open Transcriber Help.
Entering and Searching Information | 35
Download from Www.Somanuals.com. All Manuals Search And Download.
2.6 Using Phone Pad
Phone Pad provides a flexible, alternate method for entering
information. Using Phone Pad, you can easily switch between three
input modes: T9, Multi-Tap, and Numeric, including a list of symbols
for greater convenience.
To start Phone Pad
1. Start a program that accepts user input,
such as Word Mobile.
2. Tap the Input Selector arrow, then tap
Phone Pad.
Tip
Phone Pad can be started at any time, except when your device is in
Camera mode or displaying the Today screen.
Use T9 input mode
By default, the device Phone Pad is in T9 mode. It is the easiest
and most convenient way to enter text in English because it has
the capability to enter text in alphanumeric format. As you tap
alphanumeric keys on the keypad, T9 tries to automatically match the
letters you have selected with the most likely completed word.
You can do the following by using the T9 input mode:
•
•
To enter a word, tap the keys on the keypad.
To insert a word in the current program screen:
1. Tap any word in the word list (directly above the keypad).
2. Tap
.
3. Select a word, and tap
to insert the word.
36 | Entering and Searching Information
Download from Www.Somanuals.com. All Manuals Search And Download.
•
To enter a number, do any of the following:
•
•
Tap and hold on the desired number key on the keypad.
Select the numeric mode, and tap the number.
•
•
To insert a space or tab, tap
To scroll through the word list, tap
To enter a capital letter, tap
To add symbols, do any of the following:
.
or
.
•
•
.
•
Tap
to display the most frequently used symbols on the
word list.
•
Tap
to choose a symbol from the entire list.
Use Multi-Tap input mode
Multi-Tap input mode is an alphabetic mode that allows you to manually
enter individual letters to form words.
Use Numeric input mode
Numeric input mode allows you to enter a number each time you tap
a number key. You can compile several numbers on the word list,
then tap
screen.
to insert the numbers at the current cursor position on the
Use the Options screen
You can customize various behaviors for Phone Pad, including the
language database on the Options screen. To access the Phone Pad
Options screen, do any of the following:
•
•
Tap and hold
on the keypad.
Tap the Input Selector arrow at the bottom of the screen, and tap
Options. Then, on the Input Method tab of the Input screen, tap
Options.
Entering and Searching Information | 37
Download from Www.Somanuals.com. All Manuals Search And Download.
The Options screen provides you with the following settings to setup:
•
•
•
•
•
Turn on one-touch symbol entry. Select this check box to
choose one symbol at a time.
Auto-hide matching word list. Select this check box to hide the
wordlist after you choose a word.
Turn on screen tap sound. Select this check box to play a
sound each time you tap a key.
Automatically add a space after selecting a word. Select this
check box to add a space automatically at the end of every word.
Enable pop-up menu for deleting user-defined words. Select
this check box to display a pop-up (shortcut) menu whenever you
tap a word that is in the user database.
Options screen
38 | Entering and Searching Information
Download from Www.Somanuals.com. All Manuals Search And Download.
2.7 Drawing and Writing on the Screen
With your device, you can draw directly
on the screen, or write on the screen and
save notes in your own handwriting. To do
this, you must set the input mode in Notes
to Writing. If you prefer to use handwriting
or frequently add drawings to your notes,
you may find it helpful to set Writing as the
default input mode. If you prefer typed text,
set Typing as the default input mode.
For more information on what you can do
with Notes, see “Notes” in Chapter 7.
Drawing on the Screen
To set the input mode for Notes
1. Tap Start > Programs > Notes.
2. In the note list, tap Menu > Options.
3. In the Default mode box, tap one of the following:
•
•
Writing if you want to draw or enter handwritten text in a note.
Typing if you want to create a typed note.
4. Tap OK.
To write a note
1. Tap Start > Programs > Notes.
2. In the note list, tap New.
3. Write your text on the screen.
4. When finished, tap OK to return to the note list.
Notes To select handwritten text, tap and hold next to the writing. As soon as
dots appear, and before they form a complete circle, quickly drag across
the writing.
If a letter crosses three ruled lines, it is treated as a drawing rather than
text.
Entering and Searching Information | 39
Download from Www.Somanuals.com. All Manuals Search And Download.
To draw in a note
1. Tap Start > Programs > Notes.
2. In the note list, tap New.
3. To draw on the screen, use the stylus like a pen.
4. A selection box appears around your drawing.
5. When finished, tap OK to return to the note list.
Note
To select a drawing (for example, to copy or delete it), tap and hold the
drawing briefly. When you lift the stylus, the drawing is selected.
2.8 Recording a Note
You can create a stand-alone recording (voice note) or you can add a
recording to a note. For more information about creating, changing, or
saving notes, see “Notes” in Chapter 7.
To create a voice note
1. Tap Start > Programs > Notes.
2. Do one of the following:
•
•
To create a stand-alone recording, record from the note list.
To add a recording to a note, create or open a note.
3. If you do not see the Recording toolbar, tap Menu > View
Recording Toolbar.
4. Tap the record icon (
) to begin recording.
5. Hold your device’s microphone near your mouth or other source
of sound.
6. Tap the stop icon (
) when finished recording.
7. If you are adding a recording to a note, tap OK to return to the
note list when finished.
40 | Entering and Searching Information
Download from Www.Somanuals.com. All Manuals Search And Download.
8. If you are recording in an open note, an icon will appear in the
note.
9. If you are creating a stand-alone recording, the recording will
appear in the note list.
Tip
To quickly create a recording, press the RECORD button. When you
hear the beep, begin your recording. Release the button when you are
finished.
To change recording formats
1. Tap Start > Settings > Personal tab > Input.
2. Tap the Options tab, and in the Voice recording format list, tap
the format you want.
3. Tap OK.
Note
You can also change recording formats from within Notes. In the note
list, tap Menu > Options > Global Input Options link (at the bottom of
the page).
Entering and Searching Information | 41
Download from Www.Somanuals.com. All Manuals Search And Download.
2.9 Searching Information
You can search for files and other items stored on your device in the
My Documents folder or on a storage card. You can search by file
name or by words located in the item. For example, you can search in
e-mail messages, notes, appointments, contacts, and tasks, as well as
in online Help.
To search for a file or an item
1. Tap Start > Programs > Search.
2. In Search for, enter the file name, word, or other information you
want to search for.
3. If you have looked for this item before, tap the Search for arrow
and select the item from the list.
4. In Type, select a data type to help narrow your search.
5. Tap Search.
6. The My Documents folder and subfolders are searched.
7. In the Results list, tap the item you want to open.
Note
The storage card symbol
saved on a storage card.
is displayed next to the names of files
42 | Entering and Searching Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Using Phone Features
3.4 Smart Dialing
3.5 In-call Options
3.6 Additional Dialing Information
Download from Www.Somanuals.com. All Manuals Search And Download.
3.1 Using the Phone
Like a standard mobile phone, you can use your Pocket PC Phone to
make, receive, and keep track of calls and send SMS/MMS messages.
You can also take notes while talking, dial directly from Contacts, and
easily copy SIM contacts to Contacts on the device.
The Phone screen
From the Phone screen, you can access Call History, Speed Dial, and
Phone settings. To open the Phone screen, do one of the following:
•
•
•
Use the stylus and tap Start > Phone.
Press the TALK button ( ).
Directly dial the phone number
by pressing numeric keys on the
QWERTY keyboard.
TALK button
Enter your PIN
Most SIM cards are preset with a PIN (personal identification number)
that is provided by your wireless service provider. You need to enter
the PIN whenever you use your device.
1. Enter the preset PIN assigned by your wireless service provider.
2. Tap Enter.
Note
If your PIN is entered incorrectly three times, the SIM card will be
blocked. If this happens, you can unblock it with the PUK (PIN
Unblocking Key) obtained from your wireless service provider.
44 | Using Phone Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Turn on and off flight mode
In many countries you are required by law to turn off your phone on-
board an aircraft. Turning off the power doesn’t turn off the phone. You
must activate flight mode in order to turn off the phone.
You can turn on flight mode and still keep your device turned on and
use other functions.
•
Tap the Signal icon (
off the phone.
), and tap Turn on flight mode to turn
•
To resume call function, make flight mode unavailable by tapping
Turn off flight mode.
Adjust the device volume
1. Tap the Speaker icon (
).
2. Under Volume, do the following:
•
•
Adjust the phone volume (
) or
device volume ( ) by moving the
slider to the desired volume level.
Tap On, Vibrate, or Off to change
both the system and ringer volume
settings.
Volume Adjustment
Notes To adjust the conversation phone volume, you must do it during a call.
Adjusting the volume at another time will affect the ring, notification, and
MP3 sound levels.
When you activate Vibrate mode, sound will automatically be muted and
the device will vibrate when an incoming call is received. The Vibrate
icon (
) will appear in the title bar to indicate that Vibrate mode is
activated.
Using Phone Features | 45
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 Making a Call
With your device, you can make a call from Phone, Contacts, Speed
Dial, Call History, and SIM Manager.
Make a call from Phone
•
On the Phone screen, tap the desired phone number, and tap the
Talk button.
The Talk button
Phone Screen
If you tap a wrong number, tap the Back arrow (
Tip
) to erase
individual numbers one at a time. To delete all the numbers, tap and
hold the Back arrow.
Make a call from Contacts
•
Tap Start > Contacts.
•
Tap the desired contact, and press TALK twice (once to send the
number to the Phone keypad, and once to dial the number).
•
You can also tap the desired contact in the contacts list, and tap
the phone number that you want to call. Or, tap and hold the
desired contact, and on the shortcut menu, tap Call Work, Call
Home, or Call Mobile.
46 | Using Phone Features
Download from Www.Somanuals.com. All Manuals Search And Download.
To specify the number to dial
By default, the mobile telephone number (w) of a contact is dialed
when you make a call from Contacts. However, you can specify that a
different phone number is used instead.
1. Tap Start > Contacts.
2. Press NAVIGATION up or down to select the contact.
3. Press NAVIGATION left or right. The letters representing the
number will change as you scroll through them.
Make a call from Call History
1. On the Phone screen, tap the Call History button.
2. Tap Menu > Filter and tap a category.
3. Scroll to the desired contact or phone number, and tap Call.
Make a call from Speed Dial
Use Speed Dial to call frequently-used numbers with a single tap. For
example, if you assign a contact to the location 2 in Speed Dial, you
can simply tap and hold
on the Phone screen to dial the contact’s
number. Before you can create a Speed Dial entry, the number must
already exist in Contacts.
To create a Speed Dial entry
1. On the Phone screen, tap Menu > Speed Dial.
2. Tap Menu > New.
3. Tap a contact. Tap the phone number for which you want to
create a Speed Dial.
4. In the Location box, select an available location for the new
Speed Dial.
Using Phone Features | 47
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
Tips
Location 1 is generally reserved for your voice mail, and Speed Dial will
designate the next available location by default. If you want to place
a number in a position that is already occupied, the new number will
replace the number that is already there.
To create a Speed Dial entry from Contacts, tap and hold the contact
name, tap Add to Speed Dial, and select an available location for the
new Speed Dial.
To delete a Speed Dial entry, in the Speed Dial list, tap and hold the
desired entry, and tap Delete.
To make a call from SIM Manager
SIM Manager allows you to view the contents of your SIM card,
transfer SIM phonebook entries to Contacts on your device, and make
a call from your SIM card.
1. Tap Start > Programs > SIM Manager. Wait for your SIM card
contents to load.
2. Tap and hold the name or phone number of the person you want
to call, and tap Call.
3.3 Receiving a Call
When you receive a phone call, a message will appear, giving you the
option to either answer or ignore the incoming call.
To answer or reject an incoming call
•
•
To answer the call, tap Answer, or press TALK on the device.
To reject the call, tap Ignore, or press END on the device.
To end a call
Once an incoming or outgoing call is in progress, you can tap End or
press END on the device to hang up.
48 | Using Phone Features
Download from Www.Somanuals.com. All Manuals Search And Download.
3.4 Smart Dialing
Smart Dialing is a program that makes it easy for you to dial a
phone number. When you start entering numbers, Smart Dialing will
automatically search and sort the contact entries on the SIM card, in
Contacts, and the phone numbers in Call History (including incoming,
outgoing, and missed calls). Then, you can select the desired number
or contact from the filtered list to dial.
Start Smart Dialing
Open the Phone screen and tap the first digit of the number you want
to dial, and the Smart Dialing panel will appear automatically. You can
size the panel according to your need by tapping the arrow icon
.
Normal Panel
Enlarged Panel
Smart Dialing starts looking for numbers that match the sequence you
have entered. Each time you tap an additional digit or delete a digit, the
search is renewed and the result is re-displayed. The list may include
phone numbers and/or contact names associated with matching
number sequences.
Using Phone Features | 49
Download from Www.Somanuals.com. All Manuals Search And Download.
To make a call or send a text message using Smart Dialing
1. Begin entering the first few numbers.
2. In the Smart Dialing panel, browse the list by tapping the arrows
(
/
) or pressing NAVIGATION up or down to select the
desired contact or phone number.
3. The highlighted item will move one line when you press
NAVIGATION up or down; the highlighted item will scroll one
page when you tap the arrows.
4. Do one of the following:
•
•
When the correct contact is selected, tap Talk.
To call a different phone number associated with the selected
contact, tap and hold the selected contact, and tap the phone
number you want to call.
Tap and hold the contact to pop up the shortcut menu
•
To send a text message to the selected contact, tap and hold
the contact, and tap Send Text Message.
Tip
To view or edit information associated with the selected contact, tap the
contact’s name on the shortcut menu (applies only to entries stored in
Contacts on your device).
50 | Using Phone Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Set up Smart Dialing
1. On the Phone screen, and tap Menu > Smart Dialing Options.
2. On the Options tab, select the Enable Smart Dialing check box.
•
•
Select the Enable drag-scroll
check box to scroll in the matched
list by dragging.
Select the Enable double-click for
dialing check box to make a call
by double-clicking the item in the
matched list.
•
In Scroll unit, you can set up the
scrolling options when pressing
NAVIGATION up or down.
3.5 In-call Options
To put a call on hold
Your device notifies you when you have another incoming call, and
gives you the choice of rejecting or accepting the call. If you are
already on a call and accept the new call, you can choose to switch
between the two callers, or set up a conference call between all three
parties.
1. Tap Answer to take the second call, and put the first one on hold.
2. To end the second call and return to the first call, tap End or
press END on your device.
To switch between two calls
•
Tap Swap.
Using Phone Features | 51
Download from Www.Somanuals.com. All Manuals Search And Download.
To set up a conference call
1. Either put a call on hold, and dial a second number; or, accept a
second incoming call when you already have one in progress.
2. Tap Conference.
Note
Not all service providers support conference calling. Contact your
service provider for details.
To turn on and off the Speakerphone
The built-in Speakerphone on your device allows you to talk hands-free
or lets other people listen to the conversation.
•
During a call, tap Speaker On, or press and hold TALK until the
speakerphone turns on. The speakerphone icon (
the title bar.
) appears in
•
To turn off the speakerphone, tap Speaker Off, or press and hold
TALK again until the speakerphone turns off.
Warning! To avoid damage to your hearing, do not hold your device against
your ear when the Speakerphone is turned on.
To mute a call
You can turn off the microphone during a call, so that you can hear the
caller but the caller cannot hear you.
•
•
During a call, tap Mute.
When the microphone is turned off, the mute icon (
) appears
on the screen. Tap Unmute to turn on the microphone again.
52 | Using Phone Features
Download from Www.Somanuals.com. All Manuals Search And Download.
3.6 Additional Dialing Information
Make an emergency call
•
Enter the international emergency number for your locale, and
tap Talk.
Tip
Additional emergency numbers may be included in your SIM card.
Contact your service provider for details.
Make an international call
1. Tap and hold
on the Phone keypad until the + sign appears.
The + replaces the international prefix of the country that you are
calling.
2. Enter the full phone number you want to dial, and tap Talk. The
full phone number includes country code, area code (without the
leading zero, if any) and phone number.
SIM Tool Kit (STK)
A SIM card must be inserted in your device in order to use this feature,
which allows you to access a range of information services provided by
your service provider.
1. Tap Start > Programs > STK Service icon. A list of provided
services appears.
2. To access a service, tap the item in the list.
Using Phone Features | 53
Download from Www.Somanuals.com. All Manuals Search And Download.
54 | Using Phone Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Synchronizing Your Device
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1 Using ActiveSync
ActiveSync synchronizes information on your device with information
on your PC, such as Outlook content. ActiveSync can also synchronize
over a wireless or cellular network with Microsoft Exchange Server,
if your company or service provider is running Microsoft Exchange
Server with Exchange ActiveSync. When you synchronize, ActiveSync
compares the information on your device with the information on your
PC and/or Exchange Server and updates all locations with the most
recent information.
With ActiveSync, you can:
•
Synchronize information, such as Outlook E-mail, Contacts,
Calendar, or Tasks information on your device with your PC, as
well as pictures, video, and music.
•
Synchronize Outlook E-mail, Contacts, Calendar appointments,
and Tasks on your device directly with Exchange Server so that
you can stay up to date even when your PC is turned off.
•
•
Exchange files between your device and your PC without
synchronizing.
Select which types of information are synchronized and specify
how much information is synchronized. For example, you can
choose how many weeks of past Calendar appointments to
synchronize.
Before you can synchronize information with a PC, you must first install
ActiveSync on your PC and create a synchronization relationship
between your device and the PC. You can install ActiveSync from the
Getting Started CD that comes with your device. ActiveSync is already
installed on your device.
Once you have installed ActiveSync and set up a synchronization
relationship, ActiveSync on the PC recognizes your device when you
connect it, and automatically transfers the synchronization settings you
specified on your device.
56 | Synchronizing Your Pocket PC Phone
Download from Www.Somanuals.com. All Manuals Search And Download.
You may be able to synchronize your device with Exchange Server
through your company or wireless service provider. If you plan to
do so, obtain the name of the Exchange Server, your user name,
password, and domain name from your administrator before starting
the Sync Setup Wizard.
To install and set up ActiveSync
1. Install ActiveSync on your PC, as described on the Getting
Started CD. After Setup completes, the Sync Setup Wizard
automatically starts when you connect your device to the PC.
2. Follow the instructions on the screen to complete the wizard. In
the Sync Setup Wizard, do one or both of the following:
•
•
Create a synchronization relationship between your PC and
the device.
Configure an Exchange Server connection to synchronize
directly with Exchange Server.
3. Choose information types to synchronize.
Note
When you finish the wizard, ActiveSync synchronizes your device
automatically. Once synchronization completes, you can disconnect
your device from your PC.
Synchronizing Your Pocket PC Phone | 57
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2 Synchronizing Information
When you connect your device to the PC using a USB or serial cable,
an infrared connection, or a Bluetooth connection, ActiveSync will
immediately synchronize. While the device is connected, ActiveSync
synchronizes every time you make a change on either the PC or the
device.
Synchronizing Outlook information
If you have set up a synchronization relationship between your device
and the PC, synchronization keeps Outlook information up-to-date
on both computers. ActiveSync synchronizes a limited amount of
information by default to save storage space on your device. You can
change the amount of information synchronized for a given information
type in Settings for the information type.
You can set up your device to synchronize with more than one PC or
with a combination of one or more PCs and Exchange Server. When
synchronizing with multiple computers, the items that you synchronize
will appear on all of the computers with which they are synchronized.
For example, if you have set up synchronization with two PCs (PC1
and PC2), which have different items, and you synchronize Contacts
and Calendar on the device with both computers, the result is as
follows:
Location
PC1
New state
All Outlook contacts and calendar appointments that were on
PC2 are now also on PC1.
All Outlook contacts and calendar appointments that were on
PC1 are now also on PC2.
PC2
All Outlook contacts and calendar appointments from both PC1
and PC2 are on the device.
Device
Note
Outlook e-mail can be synchronized with only one computer.
58 | Synchronizing Your Pocket PC Phone
Download from Www.Somanuals.com. All Manuals Search And Download.
To start and stop synchronization
•
To synchronize Outlook information and other local information
on the PC, including media files, connect your device to the PC
using Bluetooth, infrared (IR) or a cable or cradle.
•
If you are synchronizing directly with Exchange Server, you can
use this connection to the PC to "pass through" to the network, or
you can synchronize without connecting to the PC over a cellular
or Wi-Fi network.
•
In ActiveSync, tap Sync. To end synchronization before it
completes, tap Stop.
To change which information is synchronized
1. In ActiveSync on the device, tap Menu > Options.
2. Do one or both of the following:
•
Select the check box for any items you want to synchronize.
If you cannot select a check box, you might have to clear the
check box for the same information type elsewhere in the list.
•
Clear the check box for any items you want to stop
synchronizing.
3. To stop synchronizing with one PC completely, tap the PC and
tap Delete.
Notes Outlook e-mail can be synchronized with only one computer.
To change available synchronization settings, select the type of
information and tap Settings.
To synchronize directly with Exchange Server
You can set up synchronization with Exchange Server on your device,
if it is available to you through your company or wireless service
provider. However, you should first ask your administrator for the
following information and then carry on with the steps: Exchange
Server name, your user name, password, and domain name.
Synchronizing Your Pocket PC Phone | 59
Download from Www.Somanuals.com. All Manuals Search And Download.
1. In ActiveSync on the device, tap Menu > Configure Server. If
you have not yet set up synchronization with Exchange Server,
this will say Add Server Source.
2. In Server address, enter the name of the server running
Exchange Server, and tap Next.
3. Enter your user name, password, and domain, and tap Next.
To change the rules for resolving synchronization conflicts, tap
Advanced.
4. Select the check boxes for the types of information items that you
want to synchronize with Exchange Server.
5. To change available synchronization settings, select the type of
information, and tap Settings.
6. Tap Finish.
4.3 Synchronizing via Infrared and Bluetooth
You can connect your device to the PC to synchronize using the local
wireless technologies, such as infrared (IR) and Bluetooth. These
technologies have almost similar but slightly differing requirements.
To synchronize with a PC via infrared
1. Follow the instructions in ActiveSync Help on the PC for setting
up your PC to receive infrared beams.
2. Line up the infrared (IR) ports according to the instructions in the
manufacturer’s documentation for your device so that they are
unobstructed and within close range.
3. On the device, tap Start > Programs > ActiveSync.
4. Tap Menu > Connect via IR.
5. Tap Sync.
60 | Synchronizing Your Pocket PC Phone
Download from Www.Somanuals.com. All Manuals Search And Download.
To synchronize with a PC via Bluetooth
1. Follow the instructions in ActiveSync Help on the PC for
configuring Bluetooth on your PC to support ActiveSync.
2. On the device, tap Start > Programs > ActiveSync.
3. Tap Menu > Connect via Bluetooth. Make sure that Bluetooth is
turned on at the device and the PC, and that they are within close
range.
4. If this is the first time you have connected to this PC via
Bluetooth, you must first complete the Bluetooth wizard on the
device and set up a Bluetooth partnership between your device
and the PC.
For more information about enabling and configuring Bluetooth, see
Chapter 6.
Note
You can also use the Sync Setup Wizard to set up the device to
synchronize remotely with Exchange Server. This wizard is started when
you connect your mobile device to your PC after installing ActiveSync
on the PC.
Synchronizing Your Pocket PC Phone | 61
Download from Www.Somanuals.com. All Manuals Search And Download.
4.4 Synchronizing Music, Video, and Pictures
If you want to carry your music or other digital media along with you
while you travel, ActiveSync works with Windows Media® Player to
synchronize music, video, and pictures with your device.
Other than selecting the Media information type in ActiveSync to
be synchronized, all media synchronization settings must be set in
Windows Media® Player. Before media can be synchronized, you must
do the following:
•
•
Install Windows Media® Player Version 10 on the PC.
Connect your device to the PC with a USB cable. If the device
is currently connected using Bluetooth or infrared, you must end
that connection before media can be synchronized.
•
•
Insert a storage card into your device (32MB or larger is
recommended).
Set up a sync partnership between the storage card and
Windows Media® Player.
Change Media synchronization settings
Once you select the Media information type in ActiveSync to be
synchronized, any of your favorite music, video, and picture files in
Windows Media® Player playlists can be synchronized. All you have to
do is set up synchronization in Windows Media® Player for those media
files.
To set up a sync relationship with a storage card
1. Open Windows Media® Player.
2. Click the Sync tab.
3. Select the storage card.
4. Click Set up Sync.
For information about using Windows Media® Player on the device,
see Chapter 8.
62 | Synchronizing Your Pocket PC Phone
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Managing Your Pocket PC Phone
5.6 Resetting Your Pocket PC Phone
Download from Www.Somanuals.com. All Manuals Search And Download.
5.1 Personalizing Your Pocket PC Phone
Today screen settings
The Today screen shows your upcoming appointments, active tasks,
and information about e-mail messages. You can customize the Today
screen on your device.
To customize the Today screen
1. Tap Start > Settings > Personal tab > Today.
2. On the Appearance tab, select the desired theme for the
background of the Today screen.
3. On the Items tab, select the items you want to appear on the
Today screen.
Tip
To change the order of items displayed on the Today screen, tap the
item, and tap Move Up or Move Down.
To add a custom background image
You can use one of your own pictures as the background image on the
Today screen. Be aware that pictures can affect the readability of text
on the Today screen.
1. Tap Start > Settings > Personal tab > Today.
2. Select the Use this picture as the background check box, and
tap Browse to view a list of your picture files.
3. Tap the file name of the picture you want to use.
4. Tap OK.
64 | Managing Your Pocket PC Phone
Download from Www.Somanuals.com. All Manuals Search And Download.
To set options for displaying appointments on the Today screen
If you have a large number of appointments, you may want to specify
the kind of appointments that are displayed on the Today screen.
1. Tap Start > Settings > Personal tab > Today.
2. Tap the Items tab.
3. Select Calendar and tap Options.
4. Do any of the following:
•
Select Next appointment to show only the next appointment
in your schedule, or Upcoming appointments to show
multiple appointments.
•
Clear the Display all day events check box if you do not want
to display all-day events.
To set options for displaying tasks on the Today screen
If you have a large number of tasks, you may want to specify the kind
of tasks that are displayed on the Today screen.
1. Tap Start > Settings > Personal tab > Today.
2. Tap the Items tab.
3. Select Tasks and tap Options.
4. Do any of the following:
•
Under Display number of, select the type of tasks you want
to appear on the Today screen.
•
In the Category list, select whether to display only tasks
assigned to a specific category or to display all tasks.
Managing Your Pocket PC Phone | 65
Download from Www.Somanuals.com. All Manuals Search And Download.
Customize the Start menu
You can choose which items appear in the Start menu.
1. Tap Start > Settings > Personal tab > Menus.
2. Select the check boxes of the items you want to appear in the
Start menu. You can select up to seven items.
Tip
You can also create folders and shortcuts to appear on the Start menu.
In ActiveSync on your PC, click Explore. In the Mobile Device window,
double-click My Windows Mobile-Based Device > Windows > Start
Menu, then create the folders and shortcuts that you want. You will see
the added items after you synchronize.
Set Date / Time / Language / Regional Options
You can set up the correct date, time, language, and regional settings
according to your use.
To set the time and date
1. Tap Start > Settings > System tab > Clock & Alarms.
2. Select the correct time zone and change the date or time.
Note
During synchronization, the time on your device is updated with the time
on your PC.
To set an alarm
1. Tap Start > Settings > System tab > Clock & Alarms > Alarms
tab.
2. Tap <Description> and enter a name for the alarm.
3. Tap the day of the week for the alarm. You can select multiple
days by tapping each desired day.
4. Tap the time to open a clock and set the time for the alarm.
66 | Managing Your Pocket PC Phone
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Tap the alarm icon (
) to specify the type of alarm you want.
You can choose a flashing light, a single sound, a repeating
sound, or vibration.
6. If you choose to play a sound, tap the list next to the Play sound
check box and tap the sound you want.
To set the time and date for a different location
If you visit or communicate with someone in a particular time zone
often, you can select it as your visiting time zone.
1. Tap Start > Settings > System tab > Clock & Alarms.
2. Tap Visiting.
3. Select the correct time zone and change the time or date.
To change language and regional settings
The style in which numbers, currency, dates, and times are displayed
is specified in regional settings.
1. Tap Start > Settings > System tab > Regional Settings.
2. On the Region tab, select your region and language.
3. The region you select determines which options will be available
on the other tabs.
4. To customize settings further, tap the appropriate tabs and select
the desired options.
Personal and system settings
Your device may come with programs already assigned to hardware
buttons. You can customize these buttons to open the programs you
use most, or to perform certain shortcuts such as changing the screen
orientation, opening the Today screen, or opening Input Panel.
To reassign programs or shortcuts to program buttons
1. Tap Start > Settings > Personal tab > Buttons.
Managing Your Pocket PC Phone | 67
Download from Www.Somanuals.com. All Manuals Search And Download.
2. A list of buttons and their current assignments is displayed on the
Program Buttons tab.
3. Tap the button you want to reassign. To help you identify the
buttons, there are numbers and icons representing the original
function of the button.
4. In the Assign a program box, tap the program or shortcut you
want to assign.
5. Tap OK.
To increase or decrease the size of text on the screen
1. Tap Start > Settings > System tab > Screen > Text Size tab.
2. Move the slider to increase or decrease the text size.
To enter owner information
Entering and displaying owner information are best practices; they
allow someone to return the device to you in case it is lost.
1. Tap Start > Settings > Personal tab > Owner Information.
2. On the Identification tab, enter your personal information.
Tip
If owner information is displayed on the Today screen, you can open
and edit the information directly from the Today screen. Just tap that
section of the screen.
To choose how to be notified about events or actions
1. Tap Start > Settings > Personal tab > Sounds & Notifications.
2. On the Sounds tab, choose how you want to be notified by
selecting the appropriate check boxes.
3. On the Notifications tab, in Event, tap an event name and
choose how you want to be notified by selecting the appropriate
check boxes. You can choose from several options, such as a
special sound, a message, or a flashing light.
68 | Managing Your Pocket PC Phone
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
Turning off sounds and the flashing light helps conserve battery power.
To adjust the speed for scrolling
Pressing and holding NAVIGATION up or down (Up/Down control)
scrolls through the items in a list.
1. Tap Start > Settings > Personal tab > Buttons > Up/Down
Control tab.
2. Do one of the following:
•
Under Delay before first repeat, move the slider to shorten
or lengthen the time that elapses before scrolling begins.
•
To change the time it takes to scroll from one item to the next,
under Repeat rate, move the slider to adjust the speed.
To find the operating system version number
The version of the operating system on your device will be listed near
the top of the screen.
•
Tap Start > Settings > System tab > About.
To get detailed device information
•
•
Tap Start > Settings > System tab > About.
The Version tab displays important device information, including
the type of processor and the amount of memory that is installed.
To change the device name
1. Tap Start > Settings > System tab > About.
2. Tap the Device ID tab.
3. Enter a name.
Note
The device name must begin with a letter, consist of letters from A to Z,
numbers from 0 to 9, and cannot contain spaces. Use the underscore
character to separate words.
Managing Your Pocket PC Phone | 69
Download from Www.Somanuals.com. All Manuals Search And Download.
Why is the device name important?
The device name is used to identify the device in the following
situations:
•
•
•
Synchronizing with a PC
Connecting to a network
Restoring information from a backup
Note
If you synchronize multiple devices with the same PC, each device must
have a unique name.
To make the battery last longer
•
Tap Start > Settings > System tab > Power. On the Advanced
tab, you can specify when your device turns off to conserve
battery power. For optimum conservation, specify 3 minutes or
less.
•
•
Use the AC adapter to plug your device into external power
whenever possible, especially when using a miniSD card or when
using a modem or other peripherals.
Adjust the backlight settings.
To adjust the brightness of the backlight
1. Tap Start > Settings > System tab > Backlight > Brightness
tab.
2. Move the sliders right to increase the brightness, or left to
decrease the brightness.
To set the backlight to dim after a time delay
1. Tap Start > Settings > System tab > Backlight.
2. Tap the Battery power tab, or the External power tab.
3. Select the Turn off backlight if device is not used for check
box, and specify the time delay.
70 | Managing Your Pocket PC Phone
Download from Www.Somanuals.com. All Manuals Search And Download.
Phone settings
You can customize phone settings, such as the ring type and ring tone
to be used for incoming calls, and the keypad tone to be used when
entering phone numbers.
To change the ring tone
1. From the Phone keypad, tap Menu > Options > Phone tab.
2. In the Ring tone list, tap the sound you want to use.
Tip
To use custom *.wav, *.mid, *.mp3, or *.wma files as ring tones, use
ActiveSync on your PC to copy the file to the /Windows/Rings folder on
your device. Then, select the sound from the Ring tone list. For more
information about copying files to your device, see ActiveSync Help on
your PC.
To change the ring type
You can change the way that you are notified of incoming calls. For
example, you can choose to be notified by a ring, a vibration, or a
combination of both.
1. From the Phone keypad, tap Menu > Options > Phone tab.
2. In the Ring type list, tap the desired option.
To change the keypad tone
You can change the tone you hear when entering a phone number on
the keypad. If set to Long tones, the tone is heard continuously for as
long as the number on the keypad is pressed. Use this setting if you
are having trouble accomplishing tasks that rely on tones from your
phone such as accessing messages from an answering machine. If set
to Short tones, the tone is heard only for one or two seconds. If set to
Off, no tone will be heard.
1. From the Phone keypad, tap Menu > Options > Phone tab.
2. In the Keypad list, tap the option you want.
Managing Your Pocket PC Phone | 71
Download from Www.Somanuals.com. All Manuals Search And Download.
Phone services
Phone Services, such as Call Waiting, enable you to choose how to
handle all incoming calls on your device.
To choose the services
1. Tap Start > Settings > Phone > Services tab.
2. Tap the service you want to use and tap Get Settings.
Networks
You can view available wireless networks, determine the order in which
your device accesses another network if the current one is unavailable,
and specify whether you want to change networks manually or
automatically. For more information about network settings, see Help
on your device.
To change phone network settings
1. Tap Start > Settings > Phone > Network tab.
2. By default, your device displays the current network as offered
by your service provider. You can customize to set your preferred
network.
To set preferred networks
1. Tap Start > Settings > Phone > Network tab. By default,
Network selection field is set to Automatic. However, you can
set it to Manual to choose your own network at any point of time.
2. Tap Set Networks.
3. Select the networks on the Phone: Preferred networks screen
and sort them according to your preference.
4. Tap OK.
72 | Managing Your Pocket PC Phone
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 Adding and Removing Programs
Before you purchase additional programs for your device, you should
note the name of your device, the version of Windows MobileTM
software running on it, and the type of processor. This information will
help you select a program that is compatible with your device. For
more information, see “To get detailed device information” and “To find
the operating system version number” in this chapter.
Programs available for purchase usually include a Setup program
(commonly named "setup.exe") that you must first install on your PC.
You can then use ActiveSync to add programs to your device, or add a
program directly from the Internet.
To add programs
1. Download the program to your PC (or insert the CD or disk that
contains the program into your PC). You may see a single *.exe
file, a *.zip file, a Setup.exe file, or several versions of files
for different device types and processors. Be sure to select a
program designed for your device and processor type.
2. Read any installation instructions or documentation that comes
with the program. Many programs provide special installation
instructions.
3. Connect your device and PC.
4. Double-click the *.exe file.
•
If the executable file is an installation wizard, follow the
instructions on the screen. Once the program has been
installed on your PC, the wizard will automatically transfer the
program to your device.
•
If an installation wizard does not start, you will see an
error message stating that the program is valid but that it
is designed for a different type of computer. You will need
to copy this program to your device. If you cannot find any
installation instructions for the program, use ActiveSync to
copy the program file to the Program Files folder on your
device.
Managing Your Pocket PC Phone | 73
Download from Www.Somanuals.com. All Manuals Search And Download.
To remove programs
You can only remove programs that you installed. Programs that come
with your device cannot be removed.
1. Tap Start > Settings > System tab > Remove Programs.
2. In the Programs in storage memory list, select the program you
want to remove, and tap Remove.
3. Tap Yes. If another confirmation message appears, tap Yes
again.
5.3 Managing Memory
You may need to stop a program if it becomes unstable or the program
memory is low.
To see how much memory is available
•
•
Tap Start > Settings > System tab > Memory.
On the Main tab, the amount of memory allocated to file and
data storage versus program storage is displayed, as well as the
amount of memory in use versus the available memory.
To see available storage card memory
You can see how much memory is available on a storage card that is
inserted in your device.
1. Tap Start > Settings > System tab > Memory.
2. Tap the Storage Card tab.
Tip
If you have previously inserted more than one storage card, tap the list
box and then the storage card whose information you want to see.
74 | Managing Your Pocket PC Phone
Download from Www.Somanuals.com. All Manuals Search And Download.
To free up program memory
Try the following to free memory on your device:
•
•
•
Close programs you are not currently using.
Move e-mail attachments to a storage card.
Move files to a storage card. Tap Start > Programs > File
Explorer. Tap and hold the file, and tap Cut. Browse to the
storage card folder and tap Edit > Paste.
•
•
Delete unnecessary files. Tap Start > Programs > File Explorer.
Tap and hold the file, and tap Delete.
Delete large files. To find your largest files, tap Start > Programs
> Search. In the Type list, tap Larger than 64 KB, and tap
Search.
•
In Internet Explorer Mobile, delete temporary Internet files and
clear history information. For more information, see “Internet
Explorer Mobile” in Chapter 6.
•
•
Remove programs you no longer use.
Reset your device.
To close a program
In most cases, programs automatically close to free needed memory,
however, you can close programs manually, if you prefer.
1. Tap Start > Settings > System tab > Memory > Running
Programs tab.
2. In the Running Programs list, tap the program you want to
close, and tap Stop.
Tip
In most programs, you can also use the shortcut “CTRL+Q” on the
on-screen keyboard to close the program.
Managing Your Pocket PC Phone | 75
Download from Www.Somanuals.com. All Manuals Search And Download.
5.4 Backing Up Files
You can back up files to your PC using ActiveSync, or copy files to a
storage card you insert into your device. Your device has an expansion
slot compatible with a range of mini SD storage cards.
Using ActiveSync, you can copy or move information from the PC to
the device and vice versa. Changes you make to the information on
one computer will not affect the information on the other computer. If
you want to automatically update information on both your device and
PC, synchronize the information instead. For more information about
copying and synchronizing files, see ActiveSync Help on your PC.
To copy files to a storage card
1. Push the storage card into the storage card slot until it clicks into
place. The card is secure when it does not protrude from the
base.
2. Tap Start > Programs > File Explorer and navigate to the
appropriate folder.
3. Tap and hold the file you want to copy, and tap Copy.
4. Tap the folder list (labeled My Documents by default) and tap
Storage Card.
5. Tap Menu > Edit > Paste.
To copy a file using ActiveSync
Copying a file results in separate versions of a file on your device and
PC. Because the files are not synchronized, changes made to one file
will not affect the other.
1. Connect your device to your PC.
2. In ActiveSync, click Explore, which opens the Mobile Device
folder for your device.
3. In the Mobile Device folder, go to the file that you want to copy on
your device or PC.
76 | Managing Your Pocket PC Phone
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Do one of the following:
•
To copy the file to your device, right-click the file, and click
Copy. Right-click the desired folder under Mobile Device, and
click Paste.
•
To copy the file to your PC, right-click the file and click Copy.
Right-click the desired folder on your PC, and click Paste.
To automatically save files on a storage card
In the Word Mobile, Excel Mobile, and Notes programs, you may find it
helpful to save all new documents, notes, and workbooks directly on a
storage card.
1. From the program file list, tap Menu > Options.
2. With a storage card inserted in the device, in the Save to box,
tap the appropriate storage card to automatically save new items
on the storage card.
3. Tap OK.
Note
In the file or note list, a storage card symbol is displayed next to the
names of files saved on a storage card.
Managing Your Pocket PC Phone | 77
Download from Www.Somanuals.com. All Manuals Search And Download.
5.5 Protecting Your Device
There are two kinds of security on your device. You can protect your
phone from unauthorized use by assigning a type of password called
a PIN (personal identification number). Additionally, you can prevent
unauthorized access to any part of the device by using password
protection.
Your first PIN will be given to you by your wireless service provider; you
can change the PIN later.
You create your own password when you begin using your device.
To protect your phone with a PIN
1. From the Phone keypad, tap Menu > Options > Phone tab.
2. Tap Require PIN when phone is used.
3. To change the PIN at any time, tap Change PIN.
Tip
Emergency calls can be placed at any time, without requiring a PIN.
To protect your device with a password
You can help keep your data more secure by requiring a password
every time the device is turned on.
1. Tap Start > Settings > Personal tab > Password.
2. Select the Prompt if device unused for check box, and in the
box to the right, select how long your device must be turned off
before a password is required. In the Password type box, select
the type of password you would like to use. Enter the password
and, if necessary, confirm the password.
If your device is configured to connect to a network, use a strong
password to help protect network security.
3. On the Hint tab, enter a phrase that will help you remember your
password, but doesn’t allow others to guess your password.
The hint will be displayed after the wrong password is entered
four times.
78 | Managing Your Pocket PC Phone
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Tap OK. The next time the device is turned on, you will be
prompted to enter your password.
Notes Each time a wrong password is entered, the time the device takes to
respond will get longer and longer until the device appears to be not
responding.
If you forget your password, you must follow the instructions in your
owner’s manual to clear memory before you can access your device.
To change your password
1. Tap Start > Settings > Personal tab > Password. You will be
prompted to enter your current password.
2. In the Password box, enter your new password.
3. On the Hint tab, enter a phrase that will help you remember your
new password, but doesn’t allow others to guess your password.
The hint will be displayed after the wrong password is entered
four times.
4. Tap OK.
To display owner information on the Today screen
Having your contact information displayed on the Today screen on
startup allows for easy identification of the device in case it is lost.
1. Tap Start > Settings > Personal tab > Owner Information.
2. On the Options tab, select the Identification information check
box.
3. On the Options tab, select the Notes check box if you want
additional text displayed, such as: Reward if found.
4. On the Notes tab, enter the additional text.
Tip
To display owner information on the Today screen, tap Start > Settings
> Personal tab > Today. On the Items tab, select the Owner Info
check box.
Managing Your Pocket PC Phone | 79
Download from Www.Somanuals.com. All Manuals Search And Download.
5.6 Resetting Your Pocket PC Phone
Occasionally you may need to reset your Pocket PC Phone. A normal
(or soft) reset of your device clears all active program memory and
shuts down all active programs. This can be useful when the device is
running slower than normal, or a program is not performing properly. A
soft reset is also necessary after the installation of some programs. If a
soft reset is performed when programs are running, unsaved work will
be lost.
You can also perform a hard reset (also known as a full reset). A hard
reset should be performed only if a normal reset does not solve a
system problem. After a hard reset, the device is restored to its default
settings — the way it was when you first purchased it and turned it
on. Any programs you installed, data you entered, and settings you
customized on the device will be lost. Only Windows MobileTM software
and other pre-installed programs will remain.
To perform a soft reset
•
Use the stylus to lightly press and hold the RESET button on
the left side of your device. The device restarts and displays the
Today screen.
RESET button
Warning! Always turn off your device before performing a soft reset or
installing/replacing the battery and SIM card.
80 | Managing Your Pocket PC Phone
Download from Www.Somanuals.com. All Manuals Search And Download.
To perform a hard reset
1. Press and hold the Comm Manager button and Voice Command
button on the device.
2. Keep the two buttons pressed, and at the same time, use the
stylus to lightly press and hold the RESET button.
Comm Manager button
Voice Command button
RESET button
Managing Your Pocket PC Phone | 81
Download from Www.Somanuals.com. All Manuals Search And Download.
82 | Managing Your Pocket PC Phone
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6
Getting Connected
6.4 Using Comm Manager
6.5 Using Terminal Services Client
6.6 Using Modem Link
Download from Www.Somanuals.com. All Manuals Search And Download.
6.1 Connecting to the Internet
Your device is equipped with powerful networking functions that enable
you to connect to the Internet through an Enhanced Data Rates
for GSM Evolution (EDGE)/General Packet Radio Service (GPRS)
network or a Bluetooth modem or a WLAN network. GPRS/EDGE is
a network data connection, allowing you access to the Internet or to
a corporate network to browse the Internet, and exchange e-mail or
instant messages.
Your device has two groups of connection
settings: My ISP (Internet Service Provider)
and My Work Network. The My ISP settings
are used to connect to the Internet, while
My Work Network settings can be used to
connect to any private, corporate network.
To connect to the Internet via ISP
1. Obtain the following information from
your ISP:
•
•
•
•
ISP server phone number
User name
Connection Setting
Password
Access point name (required for GPRS connection)
2. Tap Start > Settings > Connections tab > Connections.
3. Tap Add a new modem connection.
4. Enter a name for the connection.
5. Select a modem from the list. For example, if you want to use the
mobile phone network, select Cellular Line.
6. Tap Next.
7. Complete the connection wizard by entering the required
information and tap Finish.
84 | Getting Connected
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes To view additional information for any screen, tap Help.
To modify your connection settings, tap Manage existing connections on
the Connections screen, and complete the connection wizard.
To connect to a private network
1. Obtain the following information from your network administrator:
•
•
•
•
Server phone number
User name
Password
Domain (If provided by an ISP or a network administrator)
2. Tap Start > Settings > Connections tab > Connections.
3. In My Work Network, follow the instructions for each type of
connection.
4. Complete the connection wizard, then tap Finish.
Note
To start browsing the Internet or private network, tap Start > Internet
Explorer.
To reset or modify the network card settings on your device
1. Tap Start > Settings > Connections tab > Network Cards.
2. Select the Network Adapters tab.
3. In the My network card connects to list, select the appropriate
item:
•
If you want to connect to the Internet using your ISP or
WLAN to browse web page with Internet Explorer, select The
Internet.
•
If you want to connect to a private network and browse the
shared folder on the network with File Explorer, select Work.
Getting Connected | 85
Download from Www.Somanuals.com. All Manuals Search And Download.
4. In the Tap an adapter to modify settings field, select the
appropriate adapter.
5. When you select a network card and enter the settings screen,
you have to configure the required settings. On the IP Address
tab, select Use specific IP address and enter the requested
information. Contact your ISP or network administrator to obtain
the IP address, Subnet mask, and Default gateway.
6. On the Name Servers tab, configure the DNS and WINS
settings. Servers that require an assigned IP address may also
require a way to map computer names to IP addresses. DNS and
WINS are the resolution options supported on your device.
6.2 Internet Explorer Mobile
Internet Explorer Mobile is a full-featured Internet browser, optimized
for use on your mobile device.
To start Internet Explorer Mobile
•
Tap Start > Internet Explorer.
To choose a Home page
1. In Internet Explorer Mobile, tap Menu > Tools > Options >
General tab.
2. Do one of the following:
•
To use the displayed page as your Home page, tap Use
Current.
•
To use the default Home page, tap Use Default.
Tip
To go to your Home page, tap Menu > Home.
86 | Getting Connected
Download from Www.Somanuals.com. All Manuals Search And Download.
To transfer favorites from your PC
You can transfer the favorites you have stored on your PC to your
device by synchronizing the Internet Explorer favorites on your PC with
your device.
1. In ActiveSync on your PC, on the Tools menu, click Options, and
select Favorites.
2. In Internet Explorer on your PC, save or move favorite links to the
Mobile Favorites subfolder in the Favorites list.
3. Connect your mobile device to your PC. If synchronization does
not start automatically, click Sync.
To add a favorite
1. In Internet Explorer Mobile, go to the page you want to add.
2. Tap and hold the page, and tap Add to Favorites.
3. Confirm or change the name, and select a folder for storing the favorite.
To delete a favorite or folder
1. In Internet Explorer Mobile, tap Menu > Favorites > Add/Delete tab.
2. Select the item you want to delete, and tap Delete.
To change the size of text on Web pages
•
In Internet Explorer Mobile, tap Menu > Zoom, and tap the size
you want.
To show or hide pictures on Web pages
•
In Internet Explorer Mobile, tap Menu > View > Show Pictures.
A check mark next to Show Pictures indicates that pictures will
be displayed on Web pages.
Getting Connected | 87
Download from Www.Somanuals.com. All Manuals Search And Download.
To change how Web pages fill the screen
1. In Internet Explorer Mobile, tap Menu > View.
2. Tap one of the following:
•
One Column. Arranges the content into one column that is
as wide as the screen. This means that you will rarely have to
scroll horizontally.
•
Default. Maintains a layout similar to what you see on a
desktop computer, but it makes items smaller and arranges
the content so that you can see most of it without having to
scroll horizontally.
•
Desktop. Keeps the same layout and size as on a desktop
computer, which will require both horizontal and vertical
scrolling.
To clear the History list
1. In Internet Explorer Mobile, tap Menu > Tools > Options >
Memory tab.
2. Tap Clear History.
To save a picture from a Web page
1. In Internet Explorer Mobile, tap and hold the picture, and tap
Save Image.
2. Do one of the following:
•
•
To save the picture in My Pictures on your device, tap Yes.
To save the picture in another location, such as a storage
card, tap Save As.
To change cookies and security settings
Internet Explorer Mobile supports the protocols used by Secure
Sockets Layer (SSL). A connection that uses SSL helps you to send
personal information more safely.
88 | Getting Connected
Download from Www.Somanuals.com. All Manuals Search And Download.
Cookies are small files containing information about your identity and
preferences so that a page can tailor information to your needs. The
page sends the file, and it is stored on your mobile device.
1. In Internet Explorer Mobile, tap Menu > Tools > Options >
Security tab.
2. Select the check boxes for the options you want, and tap OK.
Tip
To prevent Internet Explorer Mobile from accepting any cookies, clear
the Allow cookies check box.
To delete temporary Internet files
Some Web content is stored as you view it to speed up the display
of pages you frequently visit or have already seen. You may want to
delete these files to free storage space.
1. In Internet Explorer Mobile, tap Menu > Tools > Options >
Memory tab.
2. Tap Delete Files. All pages stored on your device, including
offline favorites content, will be deleted.
Getting Connected | 89
Download from Www.Somanuals.com. All Manuals Search And Download.
6.3 Using Bluetooth
Bluetooth is a short-range wireless communications technology.
Devices with Bluetooth capabilities can exchange information over a
distance of about 10 metres without requiring a physical connection.
You can even beam information to a device in a different room, as long
as it is within the Bluetooth signal coverage range.
The software included with your device allows you to use Bluetooth in
the following ways:
•
Beam information, such as files, appointments, tasks, and contact
cards, between devices that have Bluetooth capabilities.
•
Create a dial-up modem connection between your device and a
Bluetooth-enabled phone, then transfer data using the Bluetooth
phone as a modem.
To turn on or off Bluetooth on your device
1. On your device, tap Start > Settings > Connections tab >
Bluetooth.
2. Select the Turn on Bluetooth and Make this device
discoverable to other devices check boxes.
3. Tap OK.
Bluetooth modes
Bluetooth on your device operates in three different modes:
•
•
On. Bluetooth is turned on and you can use Bluetooth features.
Off. Bluetooth is turned off. In this mode, you can neither send
nor receive information using Bluetooth. You might want to turn
the radio off at times in order to conserve battery power, or in
situations where radio use is prohibited, such as onboard an
aircraft and in hospitals.
90 | Getting Connected
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Discoverable. Bluetooth is turned on, and all other Bluetooth-
enabled devices within a range of 10 meters can detect your
device.
Note
By default, Bluetooth is turned off. If you turn it on, then turn off your
device, Bluetooth also turns off. When you turn on your device again,
Bluetooth automatically turns on.
To make your device discoverable
1. On your device, tap Start > Settings > Connections tab >
Bluetooth.
2. Select the Turn on Bluetooth and Make this device
discoverable to other devices check boxes.
3. Tap OK.
Note
Selecting the Make this device discoverable to other devices check
box also turns on Bluetooth.
Bluetooth partnerships
A Bluetooth partnership is a relationship that you create between your
device and another Bluetooth-enabled device in order to exchange
information in a secure manner. Creating a partnership between two
devices involves entering the same personal identification number
(PIN) or Passkey on both devices. Creating a partnership between
two devices is a one-time process. Once a partnership is created,
the devices can recognize the partnership and exchange information
without entering a PIN again. Make sure the two devices are within a
range of 10 meters from one another, and Bluetooth is turned on and in
discoverable mode.
Getting Connected | 91
Download from Www.Somanuals.com. All Manuals Search And Download.
To create a Bluetooth partnership
1. On your device, tap Start > Settings > Connections tab >
Bluetooth.
2. On the Devices tab, tap New Partnership. Your device searches
for other Bluetooth devices and displays them in the box.
3. Tap the desired device name in the box.
4. Tap Next.
5. Enter a passkey to establish a secure connection.
The passkey must be between 1 and 16 characters.
6. Tap Next.
7. Enter the same passkey that is entered on the other device.
You can, however, edit and enter a new name for the other
device.
8. Tap Finish.
To accept a Bluetooth partnership
1. Ensure that Bluetooth is turned on and in discoverable mode.
2. Tap Yes when prompted to establish a partnership with the other
device.
3. Enter a passkey (the same passkey that is entered on the device
requesting the partnership) to establish a secure connection. The
passkey must be between 1 and 16 characters.
4. Tap Next.
5. Tap Finish. You can now exchange information with the other
device.
To rename a Bluetooth partnership
1. Tap Start > Settings > Connections tab > Bluetooth.
2. Tap and hold the partnership on the Devices tab.
3. On the shortcut menu, tap Edit.
92 | Getting Connected
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Enter a new name for the partnership.
5. Tap Save.
To delete a Bluetooth partnership
1. Tap Start > Settings > Connections tab > Bluetooth.
2. Tap and hold the partnership on the Devices tab.
3. Tap Delete from the shortcut menu.
Beam information using Bluetooth
1. On the device, tap and hold an item to beam.
The item can be an appointment in your calendar, a task, a
contact card, or a file.
2. Tap Beam [type of item].
3. Tap the device name to which you want to send the beam. The
item is beamed to the device you selected.
Note
If the device you want to beam to does not appear in the box, make sure
that it is turned on, discoverable, and within close range (10 meters) of
your device.
Use a Bluetooth device as a modem
You can use a phone that has Bluetooth capabilities as a modem for
your device.
To do so, create a Bluetooth modem connection on your device and
then send information to another device by using Bluetooth. The device
relays the information over the network and then sends back to your
device any information that you had requested over the connection.
Once you create a modem connection to the Bluetooth phone, you can
reuse it whenever you want to use the phone as a modem. Make sure
that your device and the destination device are turned on, Bluetooth is
turned on, and that the devices are within close range.
Getting Connected | 93
Download from Www.Somanuals.com. All Manuals Search And Download.
To configure and use a Bluetooth device as a modem
1. On your device, tap Start > Settings > Connections tab >
Connections.
2. Tap Add a new modem connection.
3. Enter a name for the connection.
4. In the Select a modem list, tap Bluetooth.
5. Tap Next.
6. If the device appears in the My Connections list, skip to step 11.
7. If the device does not appear in the My Connections list, tap
New, and follow the remaining steps.
8. Select the device name from the list and tap Next.
9. Enter a passkey and tap Next.
10.Enter the same passkey on the device and tap Finish.
11.In the My Connections list, tap the device and tap Next.
12.Enter the phone number to dial for this connection and tap Next.
13.Enter the required logon information for this connection and tap
Finish.
You can start using this service for the program that uses the Bluetooth
connection, such as Inbox on your device, to send and receive e-mail,
or Internet Explorer to browse the Web.
94 | Getting Connected
Download from Www.Somanuals.com. All Manuals Search And Download.
6.4 Using Comm Manager
Comm Manager allows you to manage Wi-Fi Internet and Bluetooth
connections on your device. In addition, it allows you to control
the phone’s ringer/mute function; and, it can start ActiveSync to
synchronize (see Chapter 4 for detailed information).
You can use the device’s Power Save
Mode to make optimal use of the battery
under the WLAN networking environment,
view a variety of data related to the current
configuration and signal quality, and
increase network security.
To enable the Wi-Fi function of Comm
Manager on your device, you need access
to broadband Internet, and the necessary
access point or router that emits WLAN
signals. If you do not have access to
Comm Manager panel
broadband Internet, consult your ISP before
you try to enable Wi-Fi.
Connect to a Wi-Fi network
1. Tap Start > Programs > Comm Manager, or tap the Comm
Manger icon (
panel.
) on the Today screen, to open Comm Manager
2. Tap the Wi-Fi button to turn on/off the wireless function. The Wi-Fi
icon indicates the wireless status.
: Wi-Fi is turned on.
: Wi-Fi is turned off.
3. On the Wireless Manager screen, tap Settings > Wi-Fi Settings
to configure the required settings. When the configuration is
completed, you can connect to a Wi-Fi network using your
device.
Getting Connected | 95
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
You can also tap Start > Settings > Connections tab > Wireless LAN
to open the Wireless LAN Settings screen.
To save battery power while connected to a Wi-Fi network
•
On the Settings tab of the Wireless
LAN Settings screen, move the Power
Save Mode slider to a position that
optimizes performance with the least
power consumption.
For example, move the slider to left
(Best Performance) to have the optimal
WLAN performance; move to right
(Best Battery) to obtain the maximum
battery usage.
To check the Wireless LAN status
You can check the current wireless connection status from the
following three screens of your device:
•
Today screen. When you enable Wi-Fi on your device, the
Comm Manager icon will change to enabled mode ( ).
Wi-Fi is enabled
96 | Getting Connected
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Wireless LAN Main screen. The current connection status and
signal quality for each specific wireless channel appears on the
Wireless Manager screen with the current configuration.
•
Configure Wireless Networks screen. Tap Start > Settings >
Connections tab > Network Cards. This screen displays the
wireless networks currently available, and allows you to add new
ones if available.
Note
Wi-Fi networks are self-discoverable, meaning that no additional steps
are required for the phone to connect to a Wi-Fi network. It may be
necessary to provide a username and password for certain closed
wireless networks, however.
Getting Connected | 97
Download from Www.Somanuals.com. All Manuals Search And Download.
6.5 Using Terminal Services Client
The Terminal Services Client allows you to log on to a PC running
Terminal Services or Remote Desktop, and use all the resources
available on that PC. For example, instead of running Word Mobile on
your device, you can run the PC version of Word and access the .doc
files available on that PC.
Connect to a Terminal Server
1. On your device, tap Start > Programs > Terminal Services
Client.
2. Enter the server name.
3. You can also select a server name in Recent servers if you have
recently connected to a server.
4. Select the Limit size of server desktop to fit on this screen check
box if you want to use programs that have been specifically sized
for use with your device.
5. Tap Connect.
Navigate within Terminal Services Client
When connected to a remote server, you may notice that your device
screen is displaying more than one horizontal and vertical scroll bar.
Use these scroll bars to either scroll the contents on the PC, or to scroll
the PC display through the Terminal Services Client window.
To make sure you are scrolling the PC display through Terminal
Services Client, use the five directional buttons at the bottom of the
Terminal Services Client window. To better fit information on your
device screen, select the Limit size of server desktop to fit on this
screen check box. For best results, the programs on your desktop PC
should be maximized.
98 | Getting Connected
Download from Www.Somanuals.com. All Manuals Search And Download.
Disconnect without ending a session
1. From the Terminal Services Client screen on your device, tap
Start > Shutdown.
2. Tap Disconnect.
Notes Do not use the Start menu on your device.
If a network administrator has configured Terminal Services Client on
your device to reconnect to disconnected sessions, and you previously
disconnected from a Terminal Server without ending the session, the
Terminal Services Client reconnects to that session.
Disconnect after ending a session
1. From the Terminal Services Client screen on your device, tap
Start > Shutdown.
2. Tap Log Off.
Getting Connected | 99
Download from Www.Somanuals.com. All Manuals Search And Download.
6.6 Using Modem Link
Modem Link allows you to use your device
as an external modem for another device
(such as your PC) via the infrared or USB
connection.
Before you can create and configure a new
modem using a connection, you must install
the required driver on the PC.
Modem Link
Enable/Disable Modem Link
To activate Modem Link
1. On your device, tap Start > Programs > Modem Link.
2. In the Connection list, select the desired connection type
(IrCOMM or USB).
3. Tap Activate.
Notes Before tapping Activate, make sure your device has a GPRS SIM card
installed, and you have connected your device the a PC (via IrDA or
USB).
When you activate Modem Link, ActiveSync will be disabled
automatically .
To deactivate Modem Link
•
On the Modem Link screen, tap Deactivate.
100 | Getting Connected
Download from Www.Somanuals.com. All Manuals Search And Download.
Set Up Your PC
Before using Modem Link, you must configure a new modem on the
PC, and obtain the APN (access point name) from your ISP (Internet
service provider). To connect through a USB port, you need to first set
up a USB modem on your PC. Before setting up a USB modem, verify
that you have the following files: USBMDM, USBModem_Dialer and
ActiveSync has been installed on PC. Both files are available on the
Getting Started CD.
To configure a USB modem on your PC, run the Getting Started CD
from the CD-ROM of your PC and do the following:
1. Connect your device to the PC using the USB cable.
2. On your device, tap Start > Programs > Modem Link.
3. Select USB as the connection type.
4. Tap Activate on the Modem Link screen of your device. The
“Found New Hardware” message appears on your PC.
5. On your PC, select Display a list of the known drivers for this
device so that I can choose a specific driver and click Next.
6. In the Hardware types list, select Modem and click Next.
7. Click Next.
8. Click Have Disk, it will try to find the correct USB Modem driver
from Disk.
9. Click Next, then it complete.
10.Copy the USB Modem Dialer from the Getting Started CD to
your PC, then double-click the USB Modem Dialer.
11.Enter the GPRS settings (enter the APN assigned by your ISP).
12.Click Dial to start the connection.
Getting Connected | 101
Download from Www.Somanuals.com. All Manuals Search And Download.
To create a new dial-up connection
After a new modem has been set up on your PC, you must create a
new dial-up connection to connect your PC to the Internet using your
device.
1. On your PC, select Start > Settings > Control Panel.
2. Double-click Network and Dial-up Connections.
3. Double-click Make New Connection.
4. Click Next to continue.
5. Click Dial-up to the Internet.
6. Click Next.
7. Click Set up my connection manually and click Next.
8. Click Connect using a dial modem and click Next.
9. Enter the ISP Name and click Next.
10.Enter the telephone number as *99# and click Next.
11.You don’t have to enter the username and password when using
GPRS. Click Next to continue.
12.Enter a name for this connection and click Next.
13.Select No when the installation wizard prompts you to set up an
Internet mail account and click Next.
14.Click Finish to exit the wizard.
15.Double-click the connection you have set up and try to connect.
102 | Getting Connected
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7
Exchanging Messages
and Using Outlook
7.7 Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
7.1 E-mail and Text Messages
Messaging is where all of your e-mail accounts and your text message
account are located. You can send and receive Outlook e-mail, Internet
e-mail through an Internet service provider (ISP), and text messages.
You can also access e-mail from work using a VPN connection. For
more information about e-mail and text messages, see Help on the
device.
To set up an e-mail account
You need to set up an e-mail account that you have with an Internet
service provider (ISP) or an account that you access using a VPN
server connection (typically a work account) before you can send and
receive mail.
1. Tap Start > Messaging.
2. Tap Menu > Tools > New Account.
3. Enter your e-mail address, then tap Next. Auto configuration
attempts to download necessary e-mail server settings so that
you do not need to enter them manually.
4. Once Auto configuration has finished, tap Next.
5. Enter your name (the name you want displayed when you send
e-mail), user name, and password; tap Next.
Select the Save Password check box if you want to save your
password so that you do not need to enter it again.
If Auto configuration was successful, the Your name and User name
fields automatically get populated. Tap Next, then Finish to complete
setting up your account, or tap Options to access additional settings.
For example:
•
•
Change the time intervals for downloading new messages.
Limit the amount of messages that are downloaded and
authentication method for outgoing mails.
•
Download attachments or parts of messages.
104 | Exchanging Messages and Using Outlook
Download from Www.Somanuals.com. All Manuals Search And Download.
If Auto configuration is unsuccessful or you have an account you
access using a VPN server connection, contact your ISP or network
administrator for the following information and enter it manually:
Setting
Description
Enter the user name assigned to you by your ISP or network
administrator. This is often the first part of your e-mail
address, which appears before the at sign (@).
User name
Choose a strong password. You have the option to save
your password so you do not need to enter it each time you
connect to your e-mail server.
Password
Not required for an account with an ISP. May be required for
a work account.
Domain
Account type
Account name
Select POP3 or IMAP4.
Enter a unique name for the account, such as Work or
Home. This name cannot be changed later.
Incoming mail
server
Enter the name of your e-mail server (POP3 or IMAP4).
Enter the name of your outgoing e-mail server (SMTP).
Outgoing mail
server
Select this to ensure that you always send e-mail from this
account using an SSL connection. This enables you to send
personal information more securely. Note that if you select
this and your ISP does not support an SSL connection, you
will not be able to send e-mail.
Require SSL
connection
Outgoing
mail requires
Select this if your outgoing e-mail server (SMTP) requires
authentication. Your user name and password from above
authentication will be used.
Use separate
settings
Select this if your outgoing e-mail server requires a different
user name and password than the ones you entered before.
Exchanging Messages and Using Outlook | 105
Download from Www.Somanuals.com. All Manuals Search And Download.
Outgoing server settings:
User name
Password
Domain
Enter your user name for the outgoing e-mail server.
Enter your password for the outgoing e-mail server.
Enter the domain of the outgoing e-mail server.
Select this to ensure you always send e-mail from this
account using an SSL connection. This enables you to send
personal information more securely. Note that if you select
this and your ISP does not support an SSL connection, you
will not be able to send e-mail.
Require SSL
for outgoing
mail
Tip
You can set up several e-mail accounts in addition to your Outlook E-
mail account.
To compose and send a message
1. In the message list, tap Menu > Switch Accounts and select an
account.
2. Tap New.
3. Enter the e-mail address or text message address of one or
more recipients, separating them with a semicolon. To access
addresses and phone numbers from Contacts, tap To.
4. Enter your message. To quickly add common messages, tap
Menu > My Text and tap a desired message.
5. To check the spelling, tap Menu > Spell Check.
6. Tap Send.
Tips
To enter symbols, tap Shift using the on-screen keyboard.
To set the priority, tap Menu > Message Options.
If you are working offline, e-mail messages are moved to the Outbox
folder and will be sent the next time you connect.
If you are sending a text message and want to know if it was received,
before sending the message, tap Menu > Tools > Options. Tap Text
and select the Request delivery notification check box.
106 | Exchanging Messages and Using Outlook
Download from Www.Somanuals.com. All Manuals Search And Download.
To reply to or forward a message
1. Open the message and tap Reply, or Menu > Reply All, or
Menu > Forward.
2. Enter your response. To quickly add common messages, tap
Menu > My Text and tap a desired message.
3. To check the spelling, tap Menu > Spell Check.
4. Tap Send.
Tips
To see more header information, scroll up.
To always include the original message, from the list view, tap Menu
> Tools > Options > Message tab, and select the When replying to
e-mail, include body check box.
In the Outlook E-mail account, you will send less data if you do not edit
the original message. This may reduce data transfer costs based on
your rate plan.
To add an attachment to a message
1. In an open message, tap Menu > Insert and tap the item you
want to attach: Picture, Voice Note, or File.
2. Select the file you want to attach, or record a voice note.
To receive attachments
An attachment sent with an e-mail message or downloaded from
the server appears below the subject of the message. Tapping the
attachment opens the attachment if it has been fully downloaded, or
marks it for download the next time you send and receive e-mail. You
can also download attachments automatically with your messages if
you have an Exchange Server mail account.
If you have an Outlook E-mail account, do the following:
1. Tap Start > Programs > ActiveSync.
2. Tap Menu > Options.
3. Tap E-mail > Settings, then select Include File Attachments.
Exchanging Messages and Using Outlook | 107
Download from Www.Somanuals.com. All Manuals Search And Download.
If you have an IMAP4 E-mail account with an Internet service provider
(ISP) or an account that you access using a VPN server connection
(typically a work account), do the following:
1. Tap Start > Messaging.
2. Tap Menu > Tools > Options.
3. Tap the name of the IMAP4 account.
4. Tap Next until you reach Server information, and tap Options.
5. Tap Next twice, and select Get full copy of messages and
When getting full copy, get attachments.
Tip
To store attachments on a storage card rather than on the device,
tap Menu > Tools > Options > Storage tab, and select the Store
attachments on a storage card check box.
Downloading messages
The manner in which you download messages depends the type of
account you have:
•
•
To send and receive e-mail for an Outlook E-mail account, begin
synchronization through ActiveSync. For more information, see
“Synchronizing Outlook information” in Chapter 4.
To send and receive e-mail messages for an e-mail account
that you have with an Internet Service Provider (ISP) or that you
access using a VPN server connection (typically a work account),
download messages through a remote e-mail server. For more
information, see “To download messages from the server” later in
this chapter.
•
Text messages are automatically received when your phone
is turned on. When your phone is turned off (in flight mode),
messages are held by your service provider until the next time
your phone is turned on.
108 | Exchanging Messages and Using Outlook
Download from Www.Somanuals.com. All Manuals Search And Download.
To download messages from the server
To send and receive e-mail messages for an e-mail account that you
have with an Internet Service Provider (ISP) or that you access using
a VPN server connection (typically a work account), you first need to
connect to the Internet or your corporate network, depending on the
account.
1. Tap Menu > Switch Accounts and tap the account you want to
use.
2. Tap Menu > Send/Receive. The messages on your device and
e-mail server are synchronized: new messages are downloaded
to the device Inbox folder, messages in the device Outbox folder
are sent, and messages that have been deleted from the server
are removed from the device Inbox folder.
Tips
If you want to read the entire message, tap Menu > Download
Message while in the message window. If you are in the message list,
tap and hold the message, and tap Menu > Download Message. The
message will download the next time you send and receive e-mail. This
will also download message attachments if you selected those options
when you set up the e-mail account.
Managing folders
Each Messaging account has its own folder hierarchy with five default
Messaging folders: Inbox, Outbox, Deleted Items, Drafts, and Sent
Items. The messages you receive and send through the account are
stored in these folders. You can also create additional folders within
each hierarchy. The Deleted Items folder contains messages that
have been deleted on the device. The behavior of the Deleted Items
and Sent Items folders depends on the Messaging options you have
chosen.
Exchanging Messages and Using Outlook | 109
Download from Www.Somanuals.com. All Manuals Search And Download.
If you use an Outlook E-mail account, e-mail messages in the Inbox
folder in Outlook will be synchronized automatically with your device.
You can select to synchronize additional folders by designating them
for synchronization. The folders you create and the messages you
move will then be mirrored on the e-mail server. For example, if you
move two messages from the Inbox folder to a folder named Family,
and you have designated Family for synchronization, the server
creates a copy of the Family folder and copies the messages to that
folder. You can then read the messages while you are away from your
PC.
If you use a text message account, messages are stored in the Inbox
folder.
If you use a POP3 account and you move e-mail messages to a folder
you created, the link is broken between the messages on the device
and their copies on the e-mail server. The next time you connect, the
e-mail server will detect that the messages are missing from the Inbox
folder on the device and will delete them from the e-mail server. This
prevents having duplicate copies of a message, but it also means that
you will no longer have access to messages that you move to folders
created from anywhere except the device.
If you use an IMAP4 account, the folders you create and the e-mail
messages you move are mirrored on the e-mail server. Therefore,
messages are available to you anytime you connect to your e-mail
server, whether it is from your device or PC. This synchronization of
folders occurs whenever you connect to your e-mail server, create new
folders, or rename/delete folders when connected. You can also set
different download options for each folder.
110 | Exchanging Messages and Using Outlook
Download from Www.Somanuals.com. All Manuals Search And Download.
7.2 MMS Messages
Creating and sharing MMS messages with your friends and family is
easy with your device. You can even use the device camera to capture
photos and video clips while composing a new MMS message, and
send them along with your message.
Set up MMS
Before you can use MMS, you have to configure the required settings
on your device.
To access MMS
•
Tap Start > Messaging.
Note
You can also send an MMS message directly from the Pictures & Videos
or Camera programs. Do one of the following:
• Select a picture from My Pictures, and tap Menu > Send. In Select an
account, tap MMS.
• Capture a photo or an MMS video clip using the camera, and tap
Send. In Select an account, tap MMS.
To set up an MMS account
•
To set up your default MMS Messaging
account, tap Start > Messaging >
Menu > Switch Accounts > MMS.
Exchanging Messages and Using Outlook | 111
Download from Www.Somanuals.com. All Manuals Search And Download.
Manage MMS messages
After configuring the required settings, you can start to compose and
manage your MMS messages.
To start composing an MMS message
You can compose MMS messages in a combination of various slides,
where each slide can consist of a photo, audio or video clip, and/or
text.
1. Tap Start > Messaging.
2. Tap New, then select New Flix Message or New Pix Message.
For example, you can select New Pix Message to send an MMS
message containing photos.
3. In To, enter the recipient’s phone number or e-mail address
directly, or tap To, Cc, or Bcc to choose a phone number or an
e-mail address from Contacts.
4. Enter a subject for your message.
5. Tap the Insert icon (
) to select and send a photo or video clip.
By default, it will open My Picture folder. To navigate to any other
folder containing pictures or videos, tap the Down arrow (
corresponding to My Pictures folder.
)
6. Select a photo or video clip. When selected, you can:
•
•
•
•
Tap
Tap
Tap
to view it.
to insert it into the MMS message you are composing.
to discard it.
Tap and hold the thumbnail to display a shortcut menu
containing the options: File Info and Delete. Select File Info
to display the file information of the photo or video clip; select
Delete to remove the selected photo or video clip.
7. Enter text and insert audio clips by tapping the respective areas.
8. Tap Send to send the message.
112 | Exchanging Messages and Using Outlook
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
The following icons act as shortcuts to some of the operations on the
MMS Message screen:
• Tap
• Tap
• Tap
to preview your message
to go to the previous slide
to go to the next slide
To create an MMS message from a template
•
Tap Edit > New from Template to compose a message using a
predefined template.
Note
To save a message as a template, open the message and tap Edit >
Save as Template.
To add predefined text strings to an MMS message
You can instantly add text to any slide from a list of predefined words or
phrases, called Canned Text.
•
•
Tap
to add a text string from the Canned Text list.
To edit or delete a phrase on the Canned Text list, tap and hold a
string, then tap Edit or Delete from the shortcut menu. To create
and add a new phrase to the list, tap New.
Exchanging Messages and Using Outlook | 113
Download from Www.Somanuals.com. All Manuals Search And Download.
To add an audio clip to an MMS message
You can add audio clips to your MMS message. However, you can add
only one audio clip per slide.
1. Tap Tap here to insert an audio clip.
By default, it will open My Sounds folder. To navigate to any other
folder containing pictures or videos, tap the Down arrow (
corresponding to My Sounds folder.
)
2. Select an audio file. When selected, you can:
•
•
Tap
Tap
Tap
Tap
Tap
to play the audio clip.
to pause.
•
•
•
•
to stop.
to insert it into your MMS message.
to discard it.
To record a new audio clip and add it to your MMS message,
tap . This activates the recording control mode for a new
audio clip. Tap
to start recording, and
to stop recording.
The new audio clip is automatically inserted into your MMS
message.
To reply to an MMS message
•
Tap Menu > Reply to reply to the sender of the message, or tap
Menu > Reply All to reply to all persons listed in To, Cc, and Bcc
of the message.
To view an MMS message
You can view MMS messages in several ways.
•
•
Use the playback controls
,
, and
.
Tap Objects to see a list of files included in the message. To
save a file, select it, and tap Tools > Save.
•
View the slides manually by scrolling through the message using
the NAVIGATION control.
114 | Exchanging Messages and Using Outlook
Download from Www.Somanuals.com. All Manuals Search And Download.
To set advanced options for an MMS message
•
•
•
•
Tap Options > Background to choose a background color from
the list.
Tap Options > Text on Top to align the included text to appear at
the top of the message.
Tap Options > Text Below to align the included text to appear at
the bottom of the message.
Tap Options > Message Options to configure and manage
the sending time, validity, priority, class, and other settings for a
message.
Change MMS settings
You can set options to keep track of your messages, retrieve
messages immediately, accept or reject messages, and request a
delivery or read receipt. You can also specify a resolution for images
you send, message delivery attempts, and set up a server to access
messages.
To configure MMS settings
1. Tap Start > Messaging.
2. Tap Menu > MMS Configuration.
3. Select any of the following:
•
Retrieve messages immediately. Select this check box to
download new messages automatically without being notified.
(Typically, when you are connected to a network, you receive
a notification whenever you receive a new message.) You can
also choose to download messages when you are on your
home network only.
•
•
Save sent messages. Select this check box to save a copy of
messages that you send.
Reject all messages. Select this check box so all incoming
MMS messages are not downloaded.
Exchanging Messages and Using Outlook | 115
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Allow delivery report and Allow read report. Select these
check boxes to send and receive delivery and read reports.
Use signature with this account. When you select this
check box, you can add your personal signature in the MMS
messages. Edit your signature in the following Signature field.
•
•
Attempts before giving up. Select a value from this list to
limit the number of times the program attempts to send your
message.
Photo resolution. Select a value from this list to choose the
resolution for images that you send. Decreasing the original
resolution helps speed up the sending and receiving of
messages.
•
Servers. On this tab, you can create a new server or select an
existing one from the list to store and manage your messages.
You can also set a server as default by tapping Set As
Default.
116 | Exchanging Messages and Using Outlook
Download from Www.Somanuals.com. All Manuals Search And Download.
7.3 Pocket MSN Messenger
MSN Messenger delivers the features of MSN Messenger to your
mobile device. With Pocket MSN Messenger you can do the following:
•
•
•
Send and receive instant messages.
See which contacts are online or offline.
Subscribe to status updates for selected contacts so you know
when they come online.
•
Block contacts from seeing your status or sending you messages.
Before you can use MSN Messenger, your device must be connected
to the Internet. For information about setting up an Internet connection,
see “Connecting to the Internet” in Chapter 6.
Note
You must have either a Microsoft .NET Passport or Hotmail account to
use MSN Messenger. If you have a Hotmail.com or MSN.com e-mail
address, you already have a Passport. To get a Passport account, go to
http://www.passport.com. To get a Hotmail account, go to http://www.
hotmail.com.
To start MSN Messenger
1. Tap Start > Programs > Pocket MSN.
2. Tap MSN Messenger.
To sign in or out
•
To sign in, tap anywhere on the
MSN Messenger screen. Enter the
e-mail address and password for
your Passport or Hotmail account,
and tap Sign In. Signing in may take
several minutes, depending on your
connection speed.
•
To sign out, tap Menu > Sign Out.
Your status changes to Offline.
Exchanging Messages and Using Outlook | 117
Download from Www.Somanuals.com. All Manuals Search And Download.
To add or delete contacts
•
To add a contact, tap Menu > Add a Contact, and follow the
instructions on the screen.
•
To delete a contact, tap and hold the contact's name, and tap
Delete Contact.
To send an instant message
1. Tap the contact to whom you want to send a message.
2. Enter your message in the text entry area at the bottom of the
screen, and tap Send.
Tip
To quickly add common phrases, tap Menu > My Text and select a
phrase in the list.
To block or unblock contacts
•
To block a contact from seeing your status and sending you
messages, tap and hold the contact, then tap Block from the
shortcut menu.
•
To unblock a contact, tap and hold the name of the blocked
contact, then tap Unblock from the shortcut menu.
To check your own Messenger status
•
Tap and hold your own name at the top of the page. Your current
status is indicated in the displayed list by a bullet point.
To change your display name
1. Tap Menu > Options > Messenger tab.
2. Enter the name you want to display to others in MSN Messenger.
To get more help about MSN Messenger
•
When in MSN Messenger, tap Start > Help.
118 | Exchanging Messages and Using Outlook
Download from Www.Somanuals.com. All Manuals Search And Download.
7.4 Calendar
Use Calendar to schedule appointments, including meetings and
other events. Your appointments for the day can be displayed on the
Today screen. If you use Outlook on your PC, you can synchronize
appointments between your device and PC. You can also set Calendar
to remind you of appointments with a sound or flashing light, for
example.
You can look at your appointments in several different views (Day,
Week, Month, Year, and Agenda). To see detailed appointment
information in any view, tap the appointment.
To schedule an appointment
1. Tap Start > Calendar.
2. Tap Menu > New Appointment.
3. Enter a name for the appointment, and enter information such as
start and end times.
4. To schedule an all-day event, in the All Day box, tap Yes.
5. When finished, tap OK to return to the calendar.
Notes All-day events do not occupy blocks of time in Calendar; instead, they
appear in banners at the top of the calendar.
To cancel an appointment, tap the appointment and tap Menu > Delete.
Tip
To have the time entered automatically in Day view, tap the time slot for
the new appointment, and tap Menu > New Appointment.
Exchanging Messages and Using Outlook | 119
Download from Www.Somanuals.com. All Manuals Search And Download.
To send a meeting request
Use Calendar to schedule meetings via e-mail with contacts who use
Outlook or Outlook Mobile.
1. Tap Start > Calendar.
2. Schedule a new appointment, or open an existing one and tap
Edit.
3. Tap Attendees.
4. Tap the name of the contact you want to invite.
5. To invite each additional attendee, tap Add and tap the name.
6. Tap OK.
7. The meeting request will be sent to the attendees the next time
you synchronize your device with your PC.
Note
When attendees accept your meeting request, the meeting is
automatically added to their schedules. When their response is sent
back to you, your calendar is updated as well.
To set a default reminder for all new appointments
You can have a reminder automatically turned on for all new
appointments you schedule.
1. Tap Start > Calendar.
2. Tap Menu > Options > Appointments tab.
3. Select the Set reminders for new items check box.
4. Set the time when you want the reminder to alert you.
5. Tap OK to return to the calendar.
120 | Exchanging Messages and Using Outlook
Download from Www.Somanuals.com. All Manuals Search And Download.
7.5 Contacts
Contacts is your address book and information storage for the people
and businesses you communicate with. Store phone numbers, e-mail
addresses, home addresses, and any other information that relates to
a contact, such as a birthday or an anniversary date. You can also add
a picture or assign a ring tone to a contact.
From the contact list, you can quickly communicate with people. Tap
a contact in the list for a summary of contact information. From there,
you can call or send a message.
If you use Outlook on your PC, you can synchronize contacts between
your device and PC.
To create a contact
1. Tap Start > Contacts.
2. Tap New and enter the contact information.
3. When finished, tap OK.
Tips
If someone who is not in your list of contacts calls you or sends you
a message, you can create a contact from Call History, or from the
message by tapping Menu > Save to Contacts.
In the list of contact information, you’ll see where you can add a picture
or assign a ring tone to a contact.
To change contact information
1. Tap Start > Contacts.
2. Tap the contact.
3. Tap Menu > Edit and enter the changes.
4. When finished, tap OK.
Exchanging Messages and Using Outlook | 121
Download from Www.Somanuals.com. All Manuals Search And Download.
To work with the contact list
There are several ways to use and customize the contact list. Here are
a few tips:
1. Tap Start > Contacts.
2. In the contact list, do any of the following:
•
In Name view, you can search for a contact by entering a
name or number, or by using the alphabetical index. To switch
to Name view, tap Menu > View By > Name.
•
To see a summary of information about a contact, tap the
contact. From there you can also make a call or send a
message.
•
•
To see a list of available actions for a contact, tap and hold the
contact.
To see a list of contacts employed by a specific company, tap
Menu > View By > Company. Then, tap the company name.
To copy SIM contact to Contacts
If you have saved contacts on your SIM card, you can copy them into
Contacts on your device.
1. Tap Start > Programs > SIM Manager.
2. Select the desired item, then tap Tools > Save To Contacts.
To find a contact
There are several ways to find a contact when your contact list is long.
1. Tap Start > Contacts.
2. If you are not in Name view, tap Menu > View By > Name.
3. Do one of the following:
•
Begin entering a name or phone number in the provided
text box until the contact you want is displayed. To show all
contacts again, tap the text box and clear the text, or tap the
arrow to the right of the text box.
122 | Exchanging Messages and Using Outlook
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Use the alphabetical index displayed at the top of the contact
list.
Filter the list by categories. In the contact list, tap Menu >
Filter. Then tap a category you’ve assigned to a contact. To
show all contacts again, select All Contacts.
7.6 Tasks
Use Tasks to keep track of things you need to do. A task can occur
once or repeatedly (recurring). You can set reminders for your tasks
and you can organize them using categories.
Your tasks are displayed in a task list. Overdue tasks are displayed in
red.
To create a task
1. Tap Start > Programs > Tasks.
2. Tap New, enter a subject for the task, and fill in information such
as start and due dates, priority, and so on.
3. When finished, tap OK.
Tip
You can easily create a short, to-do-type task. Simply tap the Tap here
to add a new task box, enter a subject, and press ENTER. If the task
entry box is not available, tap Menu > Options and select the Show
Tasks entry bar check box.
To change the priority of a task
Before you can sort tasks by priority, you need to specify a priority level
for each task.
1. Tap Start > Programs > Tasks.
2. Tap the task you want to change the priority for.
3. Tap Edit and in the Priority box, tap a priority level.
4. Tap OK to return to the task list.
Exchanging Messages and Using Outlook | 123
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
All new tasks are assigned a Normal priority by default.
To set a default reminder for all new tasks
You can have a reminder automatically turned on for all new tasks you
create.
1. Tap Start > Programs > Tasks.
2. Tap Menu > Options.
3. Select the Set reminders for new items check box.
4. Tap OK to return to the task list.
Note
The new tasks must have due dates set in order for the reminder to take
effect.
To show start and due dates in the task list
1. Tap Start > Programs > Tasks.
2. Tap Menu > Options.
3. Select the Show start and due dates check box.
4. Tap OK.
To locate a task
When your list of tasks is long, you can display a subset of the tasks or
sort the list to quickly find a specific task.
1. Tap Start > Programs > Tasks.
2. In the task list, do one of the following:
•
•
Sort the list. Tap Menu > Sort by, and tap a sort option.
Filter the list by category. Tap Menu > Filter, and tap the
category you want displayed.
Tip
To filter your tasks further, tap Menu > Filter > Active Tasks or
Completed Tasks.
124 | Exchanging Messages and Using Outlook
Download from Www.Somanuals.com. All Manuals Search And Download.
7.7 Notes
Notes helps you to quickly capture thoughts, questions, reminders,
to-do lists, and meeting notes. You can create handwritten and typed
notes, record voice notes, convert handwritten notes to text for easy
readability, and send notes to others.
Entering information in Notes
There are several ways to enter information in a note. You can enter
typed text by using the on-screen keyboard or handwriting recognition
software. You can also use the stylus to write or draw directly on the
screen. On devices that support recording, you can create a stand-
alone recording or embed a recording in a note.
To set the default input mode for Notes
If you frequently add drawings to your notes, you may find it helpful to
set Writing as the default input mode. If you prefer typed text, select
Typing.
1. Tap Start > Programs > Notes.
2. In the note list, tap Menu > Options.
3. In the Default mode box, tap one of the following:
•
•
Writing if you want to draw or enter handwritten text in a note.
Typing if you want to create a typed note.
4. Tap OK.
To create a note
1. Tap Start > Programs > Notes. In the note list, tap New.
2. Tap the Input Selector arrow next to the Input Method icon on
the menu bar, tap the input method you want, and enter your text.
3. If the Input Selector arrow is not displayed, tap the Input Method
icon.
4. When finished, tap OK to return to the note list.
Exchanging Messages and Using Outlook | 125
Download from Www.Somanuals.com. All Manuals Search And Download.
126 | Exchanging Messages and Using Outlook
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8
Experiencing Multimedia
Download from Www.Somanuals.com. All Manuals Search And Download.
8.1 Using Camera
Taking photos and recording video clips along with audio is easy with
your device’s built-in camera.
To switch to any of the Camera modes
•
•
•
Tap Start > Programs > Camera; or
Tap Start > Programs > Pictures & Videos > Camera icon; or
Press CAMERA on your device.
The CAMERA button
To exit the Camera
Tap the exit icon (
•
).
Use the camera
The camera on your device allows you to capture pictures and video
clips by using various built-in modes with flexibility. The Camera mode
is set to the Photo capture mode by default. The lower right corner of
the screen displays the active capture mode. To switch to other capture
modes, do any of the following:
•
•
Tap
or
on the screen.
Press NAVIGATION left or right.
Current capture mode
128 | Experiencing Multimedia
Download from Www.Somanuals.com. All Manuals Search And Download.
The available capture modes of the camera are as follows:
•
•
•
•
Photo: Captures standard still images.
Video: Captures video clips, with or without accompanying audio.
MMS Video: Captures video clips suitable for sending via MMS.
Contacts Picture: Captures a still image and gives you the
option to immediately assign it to a Photo ID for a contact.
•
•
•
Picture Theme: Captures still images and places them within
frames.
Sport: Captures a sequence of still images (5 ~ 30) automatically
for a short duration at a defined frequency.
Burst: Captures a sequence of still images (maximum 30) as
long as CAMERA on the device or ENTER on the NAVIGATION
is kept pressed.
File formats supported
Using the above capture modes, the camera in your device captures
files in the following formats:
Capture type
Still image
Video
Format
BMP, JPEG
Motion-JPEG AVI (.avi), MPEG-4 (.mp4)
H.263 baseline (.3gp), MPEG-4 (.mp4)
JPEG
MMS Video
Burst / Sport
Experiencing Multimedia | 129
Download from Www.Somanuals.com. All Manuals Search And Download.
Use shortcuts in Camera mode
While in Camera mode, you can use the following buttons and icons on
your device as a shortcut when performing operations.
The ENTER button
Press ENTER to take a picture when you are capturing still image.
Press ENTER to start recording an incoming video stream; press it
again to stop recording.
The NAVIGATION control
•
Press NAVIGATION up or down to increase or decrease the
zoom level.
•
Press NAVIGATION left or right to go to the previous or next
sequential capture mode.
The CAMERA button
Press the CAMERA button on the device to switch to Camera mode.
If already in Camera mode, press once to take a still image or to start
recording a video clip.
Camera mode icons
Photo mode
Video mode
•
Current time indicator. The time indicator tells you the current
time (for example, the time shown in the Photo mode screenshot
is
).
130 | Experiencing Multimedia
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Remaining information indicator. The film icon (
displays the remaining, available shots of pictures based on
current settings.
)
•
•
•
•
•
Resolution indicator. The resolution icon (
indicates the current resolution.
/
/
/
/
)
Ambience indicator. The ambience icon (
indicates the current ambience.
/
/
/
/
/
)
Zoom-Ratio indicator. Tapping the up/down arrow (
the screen allows you to zoom in and zoom out.
) on
/
Mode Switching button. Tapping the left/right arrow (
the screen allows you to switch the capture mode.
) on
/
Self-Time indicator. If the Self-Timer function is enabled, the
timer icon ( ) will appear on the camera screen. When you
press the Enter button or CAMERA button to capture a still
image, it start to count down, and then capture a still image after
the assigned time (5 seconds or 10 seconds).
•
Previous/Next Template button. In Picture Theme mode, tap
the template selector icon (
) to display the previous/next
/
sequential template.
•
•
Camera Settings. Tap the tool icon ( ) to open the Camera
Settings screen. Tap OK to return to Camera mode.
Flash. Tap the flash icon to turn on/off the flash light. The
icon
indicates the flash light is turned on; the
flash light is turned off.
icon indicates the
•
•
Picture Viewer. Tap the viewer icon (
video in Pictures & Videos.
) to view the picture or
Exit. Tap the exit icon (
) to exit the Camera program.
Experiencing Multimedia | 131
Download from Www.Somanuals.com. All Manuals Search And Download.
Use Still Image capture modes
While using Still Image capture modes, such as Photo, Contacts
Picture, Picture Theme, Sport, and Burst, you can capture still
image(s) by pressing CAMERA on the device or ENTER on the
NAVIGATION control. The Still Image capture modes support either
BMP or JPEG format, as specified by you on the Camera Settings
screen.
While capturing an image in the Picture Theme capture mode, you can
select a built-in template from the default template folder. To browse
and select different templates, tap the template selector icon or tool
icon to select a template from the Camera Settings screen.
Use Video capture mode
While using the Video capture mode, you can press CAMERA or
ENTER to start recording a video clip (with audio if desired). To stop
recording, press CAMERA or ENTER again. Your device displays the
first frame of the captured video clip by default on the Review screen.
Before you capture a video clip, you can specify the recording limit in
terms of time and file size on the Camera Settings screen so that the
recording stops automatically when the clip size reaches that limit.
You can set the capture format to either Motion-JPEG AVI or MPEG-4
on the Camera Settings screen.
Use MMS Video capture mode
The MMS Video capture mode offers additional options that make it
convenient for you to capture a video file and then send it via MMS.
Press ENTER or CAMERA to start recording a video clip (with audio if
desired). To stop recording, press ENTER or CAMERA again.
To limit the size of the video that you plan to send through MMS, there
is a fixed, preset file size specified for videos captured using the MMS
Video mode. The recording process automatically stops when this limit
132 | Experiencing Multimedia
Download from Www.Somanuals.com. All Manuals Search And Download.
is reached. However, you can stop recording the video manually before
the specified limit is reached. The digital time indicator on the bottom
left corner of the screen indicates the time limit in seconds.
You can specify the capture format to be either H.263 or MPEG-4 on
the Camera Settings screen; however, the ideal format for MMS is
H.263 (3GPP). After you capture the video file, tap
screen to send the file through MMS.
on the Review
Use the Review screen
After taking a still image or recording a video clip, you can view the
image or video clip in the Review screen. In addition, you can send the
image or video clip through e-mail, or delete it immediately.
Review mode icons
Review screen of still image
Review of video
•
Back to Preview. Tap
to go back to Camera mode to capture
an image.
•
•
•
Send. Tap
to send the captured image to someone via e-mail.
to remove the captured image.
Delete. Tap
View in Pictures. Tap
to switch to Pictures & Videos program.
The captured image will be displayed in the Detailed View.
•
•
View in Windows Media. In Video capture mode, tap
switch to Windows Media® Player to play back the new video you
just recorded.
to
Assign to Contacts. Tap
to send the new file immediately to
a contact in the contact list.
Experiencing Multimedia | 133
Download from Www.Somanuals.com. All Manuals Search And Download.
To access the Review screen
1. In Camera mode, tap Tools > Options > General tab.
2. Select the Review after capture check box. Please note that this
check box is selected by default to allow you to review the image
or video clip after it has been captured.
Use zooming
While capturing a still image or a video clip by using the main camera,
you can zoom in to make the object in focus move closer, and you can
zoom out to make the object move farther away. In all capture modes,
use NAVIGATION on your device, or tap the triangular Up arrow next
to the Zoom Ratio indicator, to zoom in a still image or an incoming
video stream. When the zooming limit is reached, you will hear a beep.
To zoom out, press NAVIGATION down, or tap the Down arrow. The
main camera zoom range for a picture or a video clip depends on the
capture mode and capture size. Following is a summary.
Capture mode
Capture size setting
Scaled (1600 x 1280)
1.3M (1280 x 1024)
Large (640 x 480)
Medium (320 x 240)
Small (160 x 120)
Medium (176 x 144)
Small (128 x 96)
Zoom range
No zooming available
1.0x to 2.0x
1.0x to 2.0x
1.0x to 4.0x
1.0x to 8.0x
1.0x to 2.0x
1.0x to 2.0x
1.0x to 2.0x
1.0x to 4.0x
1.0x to 8.0x
Photo
Video and MMS Video
Contacts Picture
Large (640 x 480)
Medium (320 x 240)
Small (160 x 120)
Depends on the size of
the template currently
loaded
Determined by the
current template
Picture Theme
134 | Experiencing Multimedia
Download from Www.Somanuals.com. All Manuals Search And Download.
Capture mode
Capture size setting
Large (640 x 480)
Medium (320 x 240)
Small (160 x 120)
Large (640 x 480)
Medium (320 x 240)
Small (160 x 120)
Zoom range
1.0x to 2.0x
1.0x to 4.0x
1.0x to 8.0x
1.0x to 2.0x
1.0x to 4.0x
1.0x to 8.0x
Sport
Burst
Note
The capture sizes available for certain capture formats also vary from
one capture mode to another. The zoom range has been calculated
based on the following ratio:
• 1.0x = normal size (no zooming)
• 2.0x = double enlargement
• 4.0x = quadruple enlargement
• 8.0x = octuple enlargement
Use the Camera Settings screen
While capturing a still image or video clip using any capture modes, tap
the tool icon (
) to access the Camera Settings screen. The Camera
Settings screen allows you to configure the capture settings.
Experiencing Multimedia | 135
Download from Www.Somanuals.com. All Manuals Search And Download.
You can configure the following settings on the Camera Settings
screen.
Setting
Allows you to
Capture mode
Capture format
Capture size
Capture frequency
Record limitation
Template
Select a capture mode
Select a capture format
Select a capture size
Select a capture frequency
Specify the maximum time or file size for recording
Select a template
Browse
Navigate to a folder containing templates
Select a count of automatic capturing
Select an ambience type
Burst count
Ambience
After you configure settins, tap OK or Start Camera on the Camera
Settings screen to go back to the Camera screen.
Use the Tools menu
The Tools menu on the Camera Settings screen provides the following
advanced options for configuring and customizing the Camera mode
functions.
136 | Experiencing Multimedia
Download from Www.Somanuals.com. All Manuals Search And Download.
The Adjust item
Tap Tools > Adjust to adjust the camera display properties, such as
Contrast, Brightness, Saturation, Hue, and Gamma. Select one of
these properties from the list and move the slider (or tap the slider) to
change the value. The preview window on the Adjust screen displays
the effect of changes you make on the Adjust screen. Tap OK to save
the settings. You an tap Reset at any time to reset all properties to their
default.
The Option item
Tap Tools > Options to display the Options screen with the following
three tabs:
•
General tab. This field includes the following options:
•
Disable shutter sound. Select this check box to disable
all default sounds played while capturing a still image or
recording a video clip.
•
Keep backlight on while in viewfinder. Select this check
box to ensure that the backlight remains turned on while
you view the incoming video stream, overriding your device
backlight settings.
•
Review after capture. Select this check box to display the
captured image immediately after you take a picture. The
Review screen provides options for performing various
operations on the new file. Clearing this check box saves any
newly captured file using the default file name, and returns to
the Camera screen.
•
•
•
Apply “Date and time stamp” while capturing images.
Select this check box to automatically compose the current
date and time in the captured images.
Flicker Adjustment. To eliminate flicker image, select the
proper frequency (Auto, 50Hz, or 60Hz) of the country where
the device is being used.
Save to. Select where you want to save your files. You can
either save the files to main memory or to a storage card.
Experiencing Multimedia | 137
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Image tab. This field provides image-related settings for captured
files.
•
Prefix type and Prefix string. By default, the file name of
each new captured image file is set to “IMAGE” followed by
a sequential number, for example: IMAGE_00001.jpg. To
change this prefix, select String in the Prefix type list, then
enter the desired characters in the Prefix string box.
•
Counter Index. By default, the newly captured image files are
named with a prefix and some sequential numbers, such as
00000, 00001, 00002, and so on. To reset the numbering to
“00001” for your captured image files, tap Reset counter.
•
•
JPEG Quality. Select the JPEG image quality level for all
captured still images. You can choose from SuperFine, Fine,
Normal, and Basic.
Self-Timer. Select the Self-Timer option for capturing images:
Off, 5 seconds, or 10 seconds. Selecting 5 seconds or 10
seconds delays the capturing by the specified time after you
press CAMERA or ENTER.
•
Video Tab. The options in this field are for configuring the
advanced settings of the captured video files.
•
Prefix type and Prefix string. By default, the file name of
each new, captured video file is set to “VIDEO” followed by a
sequential number, for example: VIDEO_00001.avi. To change
this prefix, select String in the Prefix type list and enter the
desired characters in the Prefix string box.
•
•
Counter Index. By default, the newly captured video files are
named with a prefix and some sequential numbers, such as
00000, 00001, 00002, and so on. To reset the numbering to
“00001” for your captured video files, tap Reset counter.
Recording with Audio. Select this check box to record audio
with the captured video clips. This check box is selected by
default. If you clear this check box and then capture a video
clip, it would have no audio.
138 | Experiencing Multimedia
Download from Www.Somanuals.com. All Manuals Search And Download.
8.2 Using Pictures & Videos
The Pictures and Videos program collects, organizes, and sorts
images and video clips in the following formats on your device.
File Type
Image
File Extensions
*.bmp, *.jpg
Video
*.avi, *.wmv, *.mp4, *.3gp
You can view the pictures as a slide show, bean them, send them via
e-mail, edit them, or set them as the background on the Today screen.
To copy a picture or video clip to your device
You can copy pictures from your PC and view them on your device.
•
Copy the pictures from your PC or a storage card to the My
Pictures folder on your device.
For more information about copying files from your PC to your device,
see ActiveSync Help on your PC.
Note
You can also copy pictures from your PC to your device using a memory
card. Insert the memory card into the memory card slot on your device,
then copy the pictures from your PC to the folder you created on the
memory card.
To view pictures
1. Tap Start > Programs > Pictures & Videos. The images in the
My Pictures folder appear as thumbnails by default.
2. Select a picture and tap View. If you cannot find a picture in the
default My Pictures folder, go to another folder by tapping the
Down arrow.
Experiencing Multimedia | 139
Download from Www.Somanuals.com. All Manuals Search And Download.
Pictures and Videos
To play videos with audio
1. Tap Start > Programs > Pictures & Videos. The video files in
the My Pictures folder appear as thumbnails by default, which
appear with a media icon (
).
2. Select a video and tap the thumbnail to play it with the built-in
Windows Media® Player.
To view slide shows
You can view your pictures as a slide show on your device. Pictures
are shown in fullscreen view with 5-second intervals between slides.
1. Tap Start > Programs > Pictures & Videos.
2. Tap Menu > Play Slide Show.
Note
You can specify how pictures are scaled to optimize their display in
a slide show. Tap Menu > Options, then tap Portrait Pictures or
Landscape Pictures on the Slide Show tab
Tap anywhere on the screen to display the Slide Show toolbar, which
you can use to stop or pause the slide show, rotate the view, and more.
Press NAVIGATION right or left to move forward or backward through
the slides.
140 | Experiencing Multimedia
Download from Www.Somanuals.com. All Manuals Search And Download.
To sort pictures and video clips
If you store a large number of pictures or video clips on your device,
you may find it helpful to sort them to quickly find a specific picture or
clip. You can sort by name, date, and size.
1. Tap Start > Programs > Pictures & Videos.
2. Tap the sort list (labeled Date by default), and select the item you
want to sort by.
To delete a picture or video clip
Do any of the following to remove a picture or a video clip:
•
Select a picture or video clip on the Pictures & Videos screen,
and tap Menu > Delete. Tap Yes to confirm the deletion.
•
Tap and hold the thumbnail of the picture you want to delete, then
tap Delete.
To edit a picture or video clip
You can rotate, crop, and adjust the brightness and color contrast of
your pictures.
1. Tap Start > Programs > Pictures & Videos.
2. Tap the picture you want to edit.
3. Tap Menu > Edit, and do any of the following:
•
•
To rotate a picture 90 degrees counterclockwise, tap Rotate.
To crop a picture, tap Menu > Crop. Then, tap and drag to
select the area to crop. Tap outside the box to stop cropping.
•
To adjust the brightness and contrast levels of a picture, tap
Menu > AutoCorrect.
Note
To undo an edit, tap Menu > Undo. To cancel all unsaved edits you
made to the picture, tap Revert to Saved.
Experiencing Multimedia | 141
Download from Www.Somanuals.com. All Manuals Search And Download.
To set a picture as the Today screen background
You can use a picture as the background on the Today screen.
1. Tap Start > Programs > Pictures & Videos.
2. Select the picture you want to set as the background.
3. Tap Menu > Set as Today Background.
4. In Transparency level, select a higher percentage for a more
transparent picture, or a lower percentage for a more opaque
picture.
5. Tap OK.
To send pictures and video clips via e-mail
You can send pictures and video clips to other devices via e-mail.
1. First, set up Messaging to send and receive messages.
2. From the program, select the item you want to send.
3. Tap Menu > Send, and select one account (such as Outlook
E-mail or MMS) to send the attached item.
4. A new message is created with the item attached.
5. Enter the recipient name and subject, and tap Send. The
message will be sent the next time you synchronize your device.
Note
Pictures and video clips are saved automatically before they are sent.
To beam a picture
You can beam a picture to your friends or a family member using
Infrared.
1. Tap Start > Programs > Pictures & Videos.
2. Select the picture you want to beam.
3. Tap Menu > Beam.
4. Select a device to beam the picture.
5. Tap OK.
142 | Experiencing Multimedia
Download from Www.Somanuals.com. All Manuals Search And Download.
To assign pictures to contacts
You can assign a picture to a contact so that you can easily identify the
contact at any point of time.
1. Tap Start > Programs > Pictures & Videos.
2. Select the picture you want to assign to a contact.
3. Tap Menu > Save to Contact.
4. Tap the contact, or navigate and tap Select to choose the contact
from your Contacts list.
To use advance options
1. Tap Start > Programs > Pictures & Videos.
2. Select the picture for which you want to configure further settings.
3. Tap Menu > Options. The Options screen appears, allowing you
to:
•
•
•
Resize a picture so that you can send it faster to someone
using your e-mails.
Configure the view settings during slide shows and activate
screensaver options.
Configure your device camera and camcorder settings.
Experiencing Multimedia | 143
Download from Www.Somanuals.com. All Manuals Search And Download.
8.3 Using Windows Media® Player
You can use Microsoft Windows Media® Player 10 Mobile for Pocket
PC to play digital audio and video files that are stored on your device
or on a network, such as on a Web site.
Using Windows Media® Player, you can play both audio and video files.
These are the following file formats that are supported by this version
of Windows Media® Player.
File Formats Supported
Video
File Extensions
• Windows Media Video
• MPEG4 Simple Profile
• H.263
*.wmv, *.asf
*.mp4
*.3gp
• Motion JPEG
• 3GPP2
*.avi
*.3g2
Audio
• Windows Media Audio
• MP3
*.wma
*.mp3
• MIDI
*.mid, *.midi, *.rmi
*.amr
*.awb
• AMR Narrow Band
• AMR Wide Band
• AAC
*.m4a
• 3GPP2
*.gcp
About the controls
The following are available controls on the Windows Media® Player.
This control
Does this
This control
Does this
Increases the volume
level.
Plays a file.
Decreases the volume
level.
Pauses a file.
144 | Experiencing Multimedia
Download from Www.Somanuals.com. All Manuals Search And Download.
This control
Does this
This control
Does this
Skips to the beginning
of the current file or to
the previous file.
Turns the sound on
or off.
Displays a video by
using the entire screen
(full screen).
Skips to the next file.
Displays a Web site
where you can find
music and videos to
play.
Adjusts the playback
progress of a selected
file.
Note
If your device hardware supports it, you can rewind and fast-forward
files by pressing and holding the Left/Right controls.
About the screens and menus
Windows Media® Player has three primary screens:
•
Playback screen. The default screen that displays the playback
controls (such as Play, Pause, Next, Previous, and Volume), the
album art window, and the video window. You can change the
appearance of this screen by choosing a different skin.
•
•
Now Playing screen. The screen that displays the Now Playing
playlist. This special playlist indicates the currently playing file
and any files that are “queued up” to play next.
Library screen. The screen that lets you quickly find your audio
files, video files, and playlists. It contains categories such as My
Music, My Video, My TV, and My Playlists.
At the bottom of each screen is a menu called Menu. The commands
on this menu change depending upon which screen you are viewing.
Experiencing Multimedia | 145
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback screen menu
When you are viewing the Playback screen, the following commands
appear on Menu.
This control
Library
Does this
Displays the Library screen so you can choose a file to play.
Starts or pauses playback.
Stops playback.
Play/Pause
Stop
Shuffle/
Repeat
Plays the items in the Now Playing playlist randomly/
repeatedly.
Full Screen
When a video is playing, displays it by using the entire screen.
Lets you adjust various Windows Media® Player options,
including network, skin, and hardware button options.
Options
Properties
About
Displays information about the currently playing file.
Displays information about Windows Media® Player, such
as the version number.
Now Playing screen menu
When you are viewing the Now Playing screen, the following
commands appear on Menu.
This control
Library
Does this
Displays the Library screen so you can choose a file to play.
Move Up/
Down
Moves the selected item up/down in the playlist order.
Deletes the selected item from the playlist.
Remove from
Playlist
Shuffle/
Repeat
Plays the items in the Now Playing playlist randomly/
repeatedly.
Clear Now
Playing
Deletes all items from the Now Playing playlist.
Displays error information about the selected item (an
exclamation mark appears before the item name if error
details are available).
Error Details
Properties
Displays information about the selected file.
146 | Experiencing Multimedia
Download from Www.Somanuals.com. All Manuals Search And Download.
Library screen menu
When you are viewing the Library screen, the following commands
appear on Menu.
This command
Queue Up
Does this
Adds the selected item to the end of the current (Now
Playing) playlist.
Delete from
Library
MDeletes the selected item from the library.
Now Playing
Library
Displays the Now Playing screen.
Displays the Library screen so you can choose a file to play.
Update
Library
Adds new items to the library by searching your device or
storage card.
Lets you find and play files that are stored on your device or
storage card but that are not in the library..
Open File
Open URL
Properties
Lets you play a file on a network, such as the Internet.
Displays information about the selected file.
About licenses and protected files
Some content (such as digital media files downloaded from the
Internet, CD tracks, and videos) have associated licenses that protect
them from being unlawfully distributed or shared. Licenses are created
and managed by using digital rights management (DRM), which is the
technology for securing content and managing its access rights. Some
licenses may prevent you from playing files that have been copied to
your device. Files that have licenses associated with them are called
“protected files.”
If you want to copy a protected file from your PC to your device, use
the desktop Player to synchronize the file to your device (instead of
dragging the file from a folder on your PC to a folder on your device,
for example). This will ensure that the license is copied along with the
protected file. For more information about synchronizing files to your
device and other mobile devices, see desktop Player Help.
Experiencing Multimedia | 147
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
You can view the protection status for a file by checking its file
properties (tapping Menu > Properties).
To play items on your device
Use the library to find and play songs, videos, and playlists that are
stored on your device or removable storage card.
1. If you are not on the Library screen, tap Menu > Library.
2. On the Library screen, tap the Library arrow (near the top of the
screen), then tap the library that you want use (for example, My
Device or Storage Card).
3. Tap a category (for example, My Music or My Playlists), tap and
hold the item that you want to play (such as a song, album, or
artist name), then tap Play.
Note
To play a file that is stored on your device but is not in a library, on the
Library screen, tap Menu > Open File. Tap and hold the item that you
want to play (such as a file or a folder), then tap Play.
To play an item on a network
Use the Open URL command to play a song or video that is stored on
the Internet or on a network server.
1. If you are not on the Playback screen, tap OK to close the current
screen and display the Playback screen.
2. Tap Menu > Open URL.
3. Do one of the following:
•
•
In the URL box, enter a network address.
In the History box, tap a URL that you have previously used.
Note
To play an item on a network, you must be connected to a network. For
more information about creating a remote connection between your
device and a network, see Connections Help on your device.
148 | Experiencing Multimedia
Download from Www.Somanuals.com. All Manuals Search And Download.
Copy files to your device
Use the latest version of the desktop Player (Windows Media® Player
10 or later) to synchronize digital media files to your device (instead of
dragging a file from a folder on your PC to a folder on your device, for
example). Using the desktop Player ensures that licenses are copied
with protected files.
When synchronizing files, always synchronize the files to a storage
card that is inserted into your device. Do not synchronize to a storage
card that is inserted into a storage card reader. In addition, do not
synchronize to the internal storage location (RAM) in your device. For
more information about synchronizing files to mobile devices, see
desktop Player Help on the PC.
Note
Audio files copy faster if the desktop Player is configured to
automatically set the quality level for audio files copied to your device.
For more information, see desktop Player Help on the PC.
Accessibility for people with disabilities
Microsoft is committed to making its products and services easier
for everyone to use. Many accessibility features have been built into
Microsoft products, including features for individuals who have difficulty
typing or using a mouse, who are blind or have low vision, or who
are deaf or hard-of-hearing. For more information about the following
topics, see the Accessibility section of the Microsoft Web site (http://
www.microsoft.com/enable/default.aspx).
•
•
•
•
•
•
Accessibility in Microsoft Windows
Adjusting Microsoft products for people with accessibility needs
Free step-by-step tutorials
Microsoft documentation in alternative formats
Assistive technology for Windows
Customer service for people who are deaf or hard-of-hearing
Experiencing Multimedia | 149
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
The information in this section applies to users who license Microsoft
products in the United States. If you obtained this product outside the
United States, your package contains a subsidiary information card that
you can use to contact your subsidiary about the products and services
available in your area.
Troubleshooting
If you encounter a problem while using the Windows Media® Player, a
number of resources are available to help you troubleshoot the issue.
For more information, see the Troubleshooting Windows Media® Player
Mobile page at the Microsoft Web site (http://www.microsoft.com/
windows/windowsmedia/player/windowsmobile/troubleshooting.
aspx).
150 | Experiencing Multimedia
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9
Using Other Applications
9.6 Using ZIP
9.7 Using Voice Speed Dial
Download from Www.Somanuals.com. All Manuals Search And Download.
9.1 Word Mobile
Word Mobile is a streamlined version of Microsoft Word. Word
documents created on your PC can be opened and edited on your
device. You can also create and edit documents and templates in Word
Mobile and save them as *.doc, *.rtf, *.txt, and *.dot files.
You can have only one document open at a time. When you open a
second document, the first one is saved and closed automatically.
When you close a newly created document, it is automatically named
after the first several words in the document and placed in the Word
Mobile document list. You can easily rename the document with a more
meaningful name and move it to another folder or a storage card.
To create a file
1. In Word Mobile, tap New.
2. You’ll see either a blank document or template, depending on
what you’ve selected as the default template.
3. Enter text as desired.
4. When finished, tap OK to save the file.
Unsupported features in Word Mobile
Word Mobile does not fully support some features of Microsoft Word
such as revision marks and password protection. Some data and
formatting may be lost when you save the document on your device.
The following features are not supported in Word Mobile.
•
•
•
•
•
Backgrounds
Shapes and text boxes
Artistic page borders
Smart tags
Metafiles
152 | Using Other Applications
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Bi-directional text. While Word Mobile will open documents
containing bi-directional text, the indentations and alignment may
be displayed and saved incorrectly.
Password-protected files. Word Mobile does not support
opening password-protected documents. You must first remove
the password protection in Word on the PC if you want to view
the document on the device.
•
Document protection.Word Mobile does not support displaying
files that have been protected in Word on the PC.
The following features are partially supported in Word Mobile.
•
•
•
•
Picture bullets
Revision marks
Table styles
Underline styles. Underline styles not supported by Word Mobile
are mapped to one of the four supported styles: regular, dotted,
wavy, or thick/bold/wide.
•
Legacy Pocket Word files. You can open *.psw files in Word
Mobile; however, if you edit a file, you will need to save it in
*.doc, *.rtf, *.txt, or *.dot format.
The following features are not supported on the device; however, they
are retained in the file so that when a file is opened on the PC again,
they appear as expected.
•
•
•
•
Footnotes, endnotes, headers, footers
Page breaks
Lists
Fonts and font sizes. Fonts not supported by the device are
mapped to the closest font available, although the original font
will be listed on the device.
To get more help about Word Mobile
When in Word Mobile, tap Start > Help.
•
Using Other Applications | 153
Download from Www.Somanuals.com. All Manuals Search And Download.
9.2 Excel Mobile
Excel Mobile makes it easy for you to open and edit Excel workbooks
and templates created on your PC. You can also can create new
workbooks and templates on your device.
Tips
Work in full-screen mode to see as much of your workbook as possible.
Tap View > Zoom and select a percentage so that you can easily read
the worksheet.
Unsupported features in Excel Mobile
Excel Mobile does not fully support some features such as formulas
and cell comments. Some data and formatting may be lost when you
save the workbook on your device. Note the following Excel Mobile
formatting considerations:
•
Alignment. Horizontal, vertical, and wrap-text attributes remain
the same, but vertical text appears horizontal.
•
•
•
Borders. Appear as a single line.
Cell patterns. Patterns applied to cells are removed.
Fonts and font sizes. Fonts not supported by your device are
mapped to the closest font available. The original font is listed on
your device. When the workbook is opened in Excel on your PC
again, the data is displayed in the original font.
•
•
Number formats. Numbers formatted using the Microsoft Excel
97 conditional formatting feature are displayed in Number format.
Formulas and functions. If an Excel file contains a function
that is not supported by Excel Mobile, the function is removed,
and only the returned value of the function appears. The
following formulas are also converted to values: formulas entered
as an array or containing an array argument, for example,
=SUM({1;2;3;4}); formulas containing external link references
or an intersection range reference; and formulas containing
references past row 16384 are replaced with #REF!
154 | Using Other Applications
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Protection settings. Most worksheet and workbook protection
features are disabled but not removed. However, support
for password protection has been removed. Workbooks that
are password-protected or workbooks in which one or more
worksheets are password-protected cannot be opened. You must
remove the password protection in Excel on the PC and then
synchronize to open the file on the device.
•
•
Zoom settings. Are not retained. Excel supports a per worksheet
zoom setting, while the Excel Mobile zoom setting is applied to
the entire workbook.
Worksheet names. Names that reference worksheets within the
same workbook are displayed accurately, but names that refer to
other workbooks, arrays, for example, ={1;2;3;4}, array formulas,
or intersection ranges are removed from the name list. If a
name is removed from the list, it is left in formulas and functions,
causing those formulas to be resolved as “#NAME?” All hidden
names are not hidden.
•
•
•
AutoFilter settings. Are removed. However, you can use the
AutoFilter command in Excel Mobile to perform similar functions.
If you have an AutoFilter applied to a worksheet that causes rows
to be hidden, the rows remain hidden when the file is opened in
Excel Mobile. Use the Unhide command to display the hidden
rows.
Chart formatting. All charts will be saved the way they are
shown in Excel Mobile. Unsupported chart types are changed to
one of these supported types: Column, Bar, Line, Pie, Scatter,
and Area. Background colors, gridlines, data labels, trend lines,
shadows, 3D effects, secondary axes, and logarithmic scales are
turned off.
Worksheet features. The following features are not supported
in Excel Mobile and are removed or modified when a workbook
is opened on the device: hidden sheets are not hidden; VBA
modules, macro sheets, and dialog sheets are removed and
replaced with a place holder sheet; text boxes, drawing objects,
pictures, lists, conditional formats, and controls are removed;
pivot table data is converted to values.
Using Other Applications | 155
Download from Www.Somanuals.com. All Manuals Search And Download.
9.3 Viewing Slide Shows with PowerPoint Mobile
With PowerPoint Mobile, you can open and view slide show
presentations created on your PC in *.ppt and *.pps format with
PowerPoint '97 and later.
Many presentation elements built into the slide shows such as
slide transitions and animations will play back on the device. If the
presentation is set up as a timed slide show, one slide will advance to
the next automatically. Links to URLs are also supported.
PowerPoint features not supported on the device include:
•
•
•
Notes. Notes written for slides will not be visible.
Rearranging or editing slides. PowerPoint Mobile is a viewer only.
File formats. Files created in *.ppt format earlier than PowerPoint
'97 and HTML files in *.htm and *.mht formats are not supported.
To start a slide show presentation
1. Tap Start > Programs > PowerPoint Mobile.
2. In the presentation list, tap the slide show you want to view.
3. Tap the current slide to advance to the next slide.
If the presentation is set up as a timed slide show, slides will advance
automatically.
To stop a slide show
•
In a PowerPoint Mobile presentation, tap
> End Show.
To navigate between slides
You can advance to the next slide if a presentation is not set up as a
timed slide show, return to the previous slide, or go to any slide out of
sequence.
1. Tap Start > Programs > PowerPoint Mobile.
2. Open the presentation you want to view.
3. Tap
> Next or Previous, or tap Go to Slide and tap the the
slide you want to view.
156 | Using Other Applications
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
Simply tap the current slide to go to the next one.
Notes If you have zoomed in to see a slide in more detail, you cannot navigate
to another slide until you zoom out.
Tapping Next or Previous may play an animation on a slide rather than
navigate to another slide.
9.4 Using ClearVue PDF
ClearVue PDF displays Portable Document
Format (PDF) files. These files usually have
a *.pdf file extension.
To open a PDF file on your device
1. Tap Start > Programs > ClearVue
PDF.
2. Tap File > Open to view a list of PDF
files on your device.
3. Tap the file you want to view.
To navigate through a PDF document
You can do any of the following:
•
Tap the Up, Down, Right, and Left arrow keys on the horizontal
and vertical scrollbars to move to the desired direction of the
page.
•
•
•
Press NAVIGATION up, down, right, and left to move around the
page.
Tap the space between the arrow keys and the scrollbar with your
stylus to move one screen towards the desired position.
Use the Left, Right, Up, and Down arrow keys on the QWERTY
keyboard to move to the desired position.
Using Other Applications | 157
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Tap anywhere on the screen with your stylus and drag it to move
around the page so that you can view all the areas.
To enlarge or reduce the display size
1. Open a pdf file you want to view.
2. Tap Zoom.
3. Select a predefined zoom ratio, or
Page Width or Whole Page.
4. Tap Custom to set an arbitrary zoom
ratio.
9.5 Using MIDlet Manager
MIDlets are Java applications that can run on mobile devices. Your
device supports Java 2 Micro Edition, J2ME. The MIDlet Manager
allows you to download Java applications, such as games and tools
that are specifically designed for mobile devices. Although some Java
applications and games have already been installed on your device,
the Java MIDlet Manager gives you the flexibility of installing and
managing additional J2ME applications from the Internet.
To install MIDlets from the Internet
1. Locate the MIDlet/MIDlet suite while connected to the Internet.
2. Select the MIDlet/MIDlet suite to download.
3. Confirm to start downloading.
4. Run the file(s) to install.
Note
You can cancel the installation at any time.
158 | Using Other Applications
Download from Www.Somanuals.com. All Manuals Search And Download.
To install MIDlets from a PC
You can install the MIDlets/MIDlet suites on your device from a PC
using the USB sync cable, the optional cradle, infrared, or Bluetooth.
MIDlets copied to your device using infrared, Bluetooth, or e-mail
attachments are automatically saved in the My Documents folder.
However, you can copy the MIDlet file(s) from a PC to any of the
following temporary folders on your device from where MIDlet Manager
can install them.
•
•
Device memory: ../My device/My Documents/My MIDlets
Storage card: ../My device/Storage Card
Note
If the My MIDlets folder does not exist in My Documents, you can create
one with the same folder name. However, a folder named Storage Card
automatically appears after you insert an storage card into your device.
To install a MIDlet/MIDlet suite
1. Tap Start > Programs > MIDlet Manager > Menu > Install.
2. Select the MIDlet/MIDlet suite from the list.
3. Tap Install from the shortcut menu.
4. Confirm to complete the installation.
Note
To remove the MIDlet files from the temporary folder, tap Delete from
the shortcut menu.
To run MIDlets on your device
1. Tap Start > Programs > MIDlet Manager.
2. Tap a MIDlet to run.
To view the MIDlets currently running
•
On the MIDlet Manager screen, tap Show > Running.
Using Other Applications | 159
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
To view the most recently used MIDlets, tap Show > Recent.
To stop running a MIDlet
1. Tap Start > Programs > MIDlet Manager.
2. Tap Show > Running.
3. Tap and hold a MIDlet on the Running MIDlets screen, and tap
Stop.
Note
To stop all MIDlets currently running on your device, tap Menu > Stop All.
Manage MIDlets/MIDlet suites
You can organize the MIDlets into groups and define custom groups.
You can also change the default settings for a MIDlet.
To customize the display settings
1. Tap Sort By at the top of the MIDlet Manager screen.
2. Choose to sort by Name or by Size.
To change the display name of a MIDlet
1. Tap and hold a MIDlet, and tap Rename.
2. Enter a new name for the MIDlet.
3. Tap OK.
Note
You cannot change the name of a MIDlet suite.
To uninstall a MIDlet/MIDlet suite
Before you uninstall a MIDlet/MIDlet suite, make sure that it is not running.
1. Tap and hold the MIDlet/MIDlet suite on the MIDlet Manager
screen, and tap Uninstall.
2. Tap OK to confirm.
160 | Using Other Applications
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
You cannot uninstall a single MIDlet from a MIDlet suite; you can
uninstall only the complete MIDlet suite.
To check storage space
•
Tap Menu > System Info on the MIDlet Manager screen to see
how much device storage space is used by MIDlets.
To select a network type
•
Tap Menu > Choose Network Type on the MIDlet Manager
screen, and select a network type from the list.
To configure MIDlet security
You can adjust security settings for each MIDlet/MIDlet suite.
1. Tap and hold a MIDlet.
2. Tap Security from the shortcut menu.
Note that some features may not be available for all MIDlets/MIDlet
suites. Following are the security options that you can set for a running
MIDlet/MIDlet suite.
Security Option
Net Access
Description
Determines whether a MIDlet/MIDlet suite can access
the Internet.
Enables a MIDlet/MIDlet suite to access services, such
as infrared and Bluetooth.
Local Connectivity
App Auto Run
Messaging
Enables a MIDlet/MIDlet suite to run at specified times,
or any time.
Determines whether a MIDlet/MIDlet suite can send
and/or receive SMS messages.
Multimedia
Recording
Enables a MIDlet/MIDlet suite to record sounds and
images.
Using Other Applications | 161
Download from Www.Somanuals.com. All Manuals Search And Download.
Error messages
The following is a list of error messages that you may receive while
managing and using MIDlets/MIDlet suites on your device.
Error Message
Description
Either RAM shortage, or
insufficient space on the
file system
There is not sufficient memory on your device.
There is no network connection available.
Network out
The installation information provided by the
MIDlet manufacturer is inaccurate.
The jar size does not
match that specified in
the jad
The installation information provided by the
MIDlet manufacturer is inaccurate.
The jar manifest does
not match the jad
There is a problem with the installation file
provided by the MIDlet manufacturer.
Invalid Java application
descriptor (jad)
There is a problem with the installation file
provided by the MIDlet manufacturer.
Invalid Java archive
(jar)
One or more features required by this MIDlet is
not available on your device.
This Java application
is not compatible with
this device
162 | Using Other Applications
Download from Www.Somanuals.com. All Manuals Search And Download.
9.6 Using ZIP
This feature allows you to save memory and increase the storage
capacity of your device by compressing files in the conventional ZIP
format. You can view and extract archive files received from various
sources. You can also create new *.zip files on your device.
Start ZIP and Open .zip files
You can use ZIP to either archive files or open an existing archive file
on your device. Each time you start ZIP on your device, it searches for
files that have the .zip file extension, and displays these files on the
Archive List screen.
To start ZIP on your device
1. Tap Start > Programs > ZIP.
2. Open a file using any of the following:
•
•
•
Select a file and tap File > Open
Archive.
Tap and hold a file and tap Open
Archive.
Double-tap a file.
View Archive List screen
The Archive List screen displays the *.zip files on your device in the
order they are found. While adding files to an archive file, ZIP
automatically compresses the files before adding them. On the Archive
List screen, you can use the File menu and View menu. Some of the
options available on the File menu also appear on the toolbar of the
Archive List screen.
Using Other Applications | 163
Download from Www.Somanuals.com. All Manuals Search And Download.
•
File menu
•
New Archive. Lets you create a new archive file with a .zip file
extension.
•
•
•
•
Open Archive. Lets you open a ZIP file.
Rename Archive. Lets you rename an existing ZIP file.
Delete Archive. Lets you remove a ZIP file.
Archive Properties. Displays information about the current
archive file.
•
•
•
Send. Lets you send a ZIP file either via e-mail or infrared.
Recent. Displays a list of recently used files.
Options. Lets you set various view mode and compression
level options for an archive file.
•
About ZIP. Displays version and copyright information.
•
View menu
•
•
•
•
Large Icons. Displays all files as large icons.
Small Icons. Displays all files as small icons.
List. Displays all files in a list.
Details. Displays all files in detail.
Note
You cannot select multiple ZIP files.
Manage a ZIP file
After you open a ZIP file, you can either
extract the file to a folder or location, or
perform various tasks on the file. The icons
on the toolbar of the ZIP screen also provide
some of these functions. Following is an
illustration of the ZIP screen.
164 | Using Other Applications
Download from Www.Somanuals.com. All Manuals Search And Download.
•
File menu
•
New Archive. Creates a new archive file with a .zip file
extension.
•
•
•
•
•
Find Archive. Locates an archive file.
Close Archive. Closes an archive file.
Rename Archive. Lets you rename an archive file.
Delete Archive. Removes an archive file.
Archive Properties. Displays information about the current
archive file.
•
•
•
Integrity Test. Checks the selected file for data correctness
and reliability.
Refresh. Lets you refresh the content of the current archive
file.
Recent. Displays a list of recently opened archive files,
including the current file.
•
Action menu
•
•
Add. Lets you add files to the archive.
Extract. Lets you extract files from the archive to the folder of
your choice.
•
•
•
•
•
Delete. Removes files from the archive.
Send via E-mail. Lets you send the archive file via e-mail.
Send via Infrared. Lets you send the archive file via infrared.
View. Lets you view a file from the archive file.
Multi-Select Mode. Lets you select multiple files in the
archive file.
•
•
•
Select All. Selects all files in the archive file.
Select None. Clears all selected files in the archive file.
Select Invert. Selects in reverse from the archive file.
Using Other Applications | 165
Download from Www.Somanuals.com. All Manuals Search And Download.
•
View menu
•
•
Show Folders. Shows the folder instead of the entire path.
Up One Level. Takes you up one level from the current
directory.
•
•
•
•
•
•
•
•
•
Large Icons. Displays all files as large icons.
Small Icons. Displays all files as small icons.
List. Displays all files in a list.
Details. Displays all files in detail.
Extended. Displays all files in detail.
Sort by. Sorts all files by the sort order you select.
Properties. Displays information about the current file.
Status Pane. Displays the status of the current file.
Toolbar. Shows or hides the toolbar.
•
Tools menu
•
Options. Lets you set various view mode and compression
level options for an archive file.
•
About Zip. Displays version and copyright information.
166 | Using Other Applications
Download from Www.Somanuals.com. All Manuals Search And Download.
9.7 Using Voice Speed Dial
You can record voice tags so that you can dial a phone number or
launch programs simply by speaking a word
Create a voice tag for a phone number
1. Tap Start > Contacts, or tap Contacts
on Today screen, to open the Contacts
list.
2. Do one of the following:
•
•
•
Tap and hold the desired contact,
then tap Add Voice Tag.
Select the desired contact, then tap
Menu > Add Voice Tag.
Tap the desired contact to open
the contact’s detailed screen, then
select a phone number and tap
Menu > Add Voice Tag.
3. Select the phone number that you want to create a voice tag,
then tap the record button (
).
Select the desired
phone number.
Tap the record button
to start recording.
Using Other Applications | 167
Download from Www.Somanuals.com. All Manuals Search And Download.
4. When completed, a voice tag icon (
) will be displayed on the
right of the item.
5. When you create a voice tag for the item, you can do one of the
following:
•
•
•
Tap the record button (
Tap the play button (
Tap the delete button (
) to rebuild the voice tag.
) to play the voice tag.
) to delete the voice tag.
The voice tag icon
The control buttons
Tip
To improve the accuracy, please record your voice in a quiet place.
Create a voice tag for a program
1. Tap Start > Settings > Personal tab >
Voice Speed Dial.
2. On the Application tab, it displays a list
of all installed programs on your device.
3. Create a voice tag for the desired
program as described above.
4. Now, you can launch the program by
saying the recorded voice tag after
pressing the Voice Command button.
168 | Using Other Applications
Download from Www.Somanuals.com. All Manuals Search And Download.
Make a call or launch programs using a voice tag
1. Press the Voice Command button on
your device.
2. After a “beep” sound, say the recorded
voice tag that you have assigned to the
phone number you want to call or the
program you want to launch. The system
will repeat the voice tag and then dial out
or launch the program automatically.
Note
If the system can not recognize your voice tag, please speak clearly
and reduce the surrounding noise. Then, try again.
To view and test the voice tags you have created
1. Tap Start > Settings > Personal tab > Voice Speed Dail.
2. On the Voice Tag tab, it displays a list
that contains all the voice tags you have
created.
3. Select an item in the list, and you can
do one of the following:
•
•
•
Tap the record button (
the voice tag.
) to rebuild
) to play the
) to delete
Tap the play button (
voice tag.
Tap the delete button (
the voice tag.
Using Other Applications | 169
Download from Www.Somanuals.com. All Manuals Search And Download.
170 | Using Other Applications
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
A.2 PC Requirement to Run ActiveSync 4.x
A.3 Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
A.1 Regulatory Notices
Regulatory Agency IDs
For regulatory identification purposes, your product is assigned a
model number of WIZA100.
To ensure continued reliable and safe operation of your device, use
only the accessories listed below with your WIZA100.
The Battery Pack has been assigned a model number of WIZA16.
This product is intended for use with a certified Class 2 Limited Power
Source, rated 5 Volts DC, maximum 1 Amp power supply unit.
European Union Notice
Products with CE marking comply with the R&TTE Directive (99/5/
EC), the EMC Directive (89/336/EEC), and the Low Voltage Directive
(73/23/EEC) issued by the Commission of the European Community.
Compliance with these directives implies conformity to the following
European Norms (in parentheses are the equivalent international
standards).
•
EN 60950-1 (IEC 60950-1)
Safety of InformationTechnology Equipment.
•
ETSI EN 301 511
Global system for mobile communications (GSM); Harmonized
EN for mobile stations in the GSM 900 and GSM 1800 bands,
covering essential requirements of article 3.2 of the R&TTE
directive (1995/5/EC ).
•
ETSI EN 301 489-1
Electromagnetic compatibility and Radio spectrum Matters
(ERM); ElectroMagnetic Compatibility (EMC) standard for radio
equipment and services; Part 1: Common technical requirements.
172 | Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
ETSI EN 301 489-7
Electromagnetic compatibility and Radio spectrum Matters
(ERM); ElectroMagnetic Compatibility (EMC) standard for radio
equipment and services; Part 7: Specific conditions for mobile
and portable radio and ancillary equipment of digital cellular radio
telecommunications systems (GSM and DCS).
ETSI EN 301 489-17
Electromagnetic compatibility and Radio spectrum Matters
(ERM); ElectroMagnetic Compatibility (EMC) standard for radio
equipment and services; Part 17: Specific conditions for 2.4 GHz
wideband transmission systems and 5 GHz high performance
RLAN equipment.AccessoriesModel NumberCradlePH15x
ETSI EN 300 328
Electromagnetic compatibility and Radio spectrum Matters
(ERM); Wideband Transmission systems; data transmission
equipment operating in the 2.4 GHz ISM band and using spread
spectrum modulation techniques.
•
•
EN 50360:2001
Product standard to demonstrate the compliance of mobile
phones with the basic restrictions related to human exposure to
electromagnetic fields (300 MHz - 3 GHz).
EN 50371:2002
Generic standard to demonstrate the compliance of low power
electronic and electrical apparatus with the basic restrictions
related to human exposure to electromagnetic fields (10 MHz
- 300 GHz) - General public.
Appendix | 173
Download from Www.Somanuals.com. All Manuals Search And Download.
This equipment may be operated in:
AT
FI
BE
FR
LV
PT
IS
CY
DE
LT
CZ
GR
LU
SI
DK
HU
MT
ES
CH
EE
IE
IT
NL
SE
BG
PL
GB
RO
SK
LI
NO
TR
Federal Communications Commission Notice
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harm-ful interference to radio or TV reception,
which can be determined by turning the equipment on and off, the user
is encouraged to try to correct the interference by one or more of the
following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•
Consult the dealer or an experienced radio or television
technician for help.
174 | Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
Modifications
The FCC requires the user to be notified that any changes or
modifications made to the device that are not expressly approved
by High Tech Computer Corporation may void the user’s authority to
operate the equipment.
Important Health and Safety Information
Retain and follow all product safety and operating instructions. Observe
all warnings in the operating instructions on the product.
To reduce the risk of bodily injury, electric shock, fire, and damage to
the equipment, observe the following precautions.
Safety Precautions for RF Exposure
Tests for SAR are conducted using standard operating positions
specified by the FCC with the phone transmitting at its highest certified
power level in all tested frequency bands. Although the SAR is
determined at the highest certified power level, the actual SAR level
of the phone while operation can be well below the maximum value.
This is because the phone is designed to operate at multiple power
levels so as to use only the power required to reach the network. In
general, the closer you are to a wireless base station antenna, the
lower the power output. Before a phone model is available for sale to
the public, it must be tested and certified to the FCC that it does not
exceed the limit established by the government-adopted requirement
for safe exposure. The tests are performed in positions and locations
(for example, at the ear and worn on the body) as required by the
FCC for each model. (Body-worn measurements may differ among
phone models, depending upon available accessories and FCC
requirements). For body worn operation, to maintain compliance with
FCC RF exposure guidelines, use only original manufacturer approved
accessories. When carrying the phone while it is on, use the specific
original manufacturer supplied or approved carrying case, holster, or
other body-worn accessory.
Appendix | 175
Download from Www.Somanuals.com. All Manuals Search And Download.
General Precautions
•
Heed service markings
Except as explained elsewhere in the Operating or Service
documentation, do not service any product yourself. Service
needed on components inside these compartments should be
done by an authorized service technician or provider.
•
Damage requiring service
Unplug the product from the electrical outlet and refer servicing to
an authorized service technician or provider under the following
conditions:
•
Liquid has been spilled or an object has fallen into the
product.
•
•
•
•
The product has been exposed to rain or water.
The product has been dropped or damaged.
There are noticeable signs of overheating.
The product does not operate normally when you follow the
operating instructions.
•
Avoid hot areas
The product should be placed away from heat sources such as
radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
•
•
Avoid wet areas
Never use the product in a wet location.
Avoid pushing objects into product
Never push objects of any kind into cabinet slots or other
openings in the product. Slots and openings are provided for
ventilation. These openings must not be blocked or covered.
•
Mounting Accessories
Do not use the product on an unstable table, cart, stand,
tripod, or bracket. Any mounting of the product should follow
the manufacturer’s instructions, and should use a mounting
accessory recommended by the manufacturer.
176 | Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Avoid unstable mounting
Do not place the product with an unstable base.
Use product with approved equipment
This product should be used only with personal computers and
options identified as suitable for use with your equipment.
•
•
Adjust the volume
Turn down the volume before using headphones or other audio
devices.
Cleaning
Unplug the product from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning, but NEVER use water to clean the LCD screen.
Safety Precautions for Power Supply Unit
•
Use the correct external power source
A product should be operated only from the type of power source
indicated on the electrical ratings label. If you are not sure of the
type of power source required, consult your authorized service
provider or local power company. For a product that operates
from battery power or other sources, refer to the operating
instructions that are included with the product.
•
Handle battery packs carefully
This product contains a Li-Ion Polymer battery. There is a risk of
fire and burns if the battery pack is handled improperly. Do not
attempt to open or service the battery pack. Do not disassemble,
crush, puncture, short external contacts or circuits, dispose of
in fire or water, or expose a battery pack to temperatures higher
than 60˚C (140˚F).
Appendix | 177
Download from Www.Somanuals.com. All Manuals Search And Download.
Exposure to Radio Frequency (RF) Signals
Your wireless phone is a radio transmitter and receiver. It is designed
and manufactured not to exceed the emission limits for exposure
to radio frequency (RF) energy set by the Federal Communications
Commission of the U.S. Govern-ment. These limits are part of
comprehensive guidelines and establish permitted levels of RF energy
for the gen-eral population. The guidelines are based on the safety
standards previously set by both U.S. and international standards
bodies:
•
•
American National Standards Institute (ANSI) IEEE. C95.1-1992
National Council on Radiation Protection and Measure-ment
(NCRP). Report 86. 1986
•
•
International Commission on Non-Ionizing Radiation Protection
(ICNIRP) 1996
Ministry of Health (Canada), Safety Code 6. The standards
include a substantial safety margin designed to assure the safety
of all persons, regardless of age and health.
In the U.S. and Canada, the SAR limit for mobile phones used by the
public is 1.6 Watts/kg (W/kg) averaged over one gram of tissue. The
standard incorporates a substantial margin of safety to give additional
protection for the public and to account for any variations in usage.
Normal condi-tions only ensure the radiative performance and safety
of the interference. As with other mobile radio transmitting equip-ment,
users are advised that for satisfactory operation of the equipment
and for the safety of personnel, it is recommended that no part of
the human body be allowed to come too close to the antenna during
operation of the equipment.
178 | Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
SAR Information
•
•
•
1.132 W/Kg @ 1g (FCC) body
0.251 W/Kg @ 1g (FCC) head
0.242 W/Kg @ 10g (CE)
Warning! DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. TO REDUCE RISK OF FIRE OR BURNS, DO NOT
DISASSEMBLE, CRUSH, PUNCTURE, SHORT EXTERNAL
CONTACTS, EXPOSE TO TEMPERATURE ABOVE 60˚C (140˚F),
OR DISPOSE OF IN FIRE OR WATER. REPLACE ONLY WITH
SPECIFIED BATTERIES. RECYCLE OR DISPOSE OF USED
BATTERIES ACCORDING TO THE LOCAL REGULATIONS OR
REFERENCE GUIDE SUPPLIED WITH YOUR PRODUCT.
Appendix | 179
Download from Www.Somanuals.com. All Manuals Search And Download.
A.2 PC Requirement to Run ActiveSync 4.x
To connect your device to the PC, you must have Microsoft®
ActiveSync® program installed on your PC. ActiveSync 4.x is included
in the Installation CD, which is compatible with the following operating
systems and applications:
•
•
•
•
•
•
•
•
•
•
Microsoft® Windows® 2000 Service Pack 4
Microsoft® Windows® Server 2003 Service Pack 1
Microsoft® Windows® Server 2003 IA64 Edition Service Pack 1
Microsoft® Windows® Server 2003 x64 Edition Service Pack 1
Microsoft® Windows® XP Professional Service Packs 1 and 2
Microsoft® Windows® XP Home Service Packs 1 and 2
Microsoft® Windows® XP Tablet PC Edition 2005
Microsoft® Windows® XP Media Center Edition 2005
Microsoft® Windows® XP Professional x64 Edition
Microsoft® Outlook® 98, Microsoft® Outlook® 2000 and
Microsoft® Outlook® XP, and Microsoft® Outlook® 2003
messaging and collaboration clients
•
•
•
•
•
•
Microsoft® Office 97, excluding Outlook
Microsoft® Office 2000
Microsoft® Office XP
Microsoft® Office 2003
Microsoft® Internet Explorer 4.01 or later (required)
Microsoft® Systems Management Server 2.0
180 | Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
A.3 Troubleshooting
If you encounter any problems with your device, consult the following
guide and try to solve these problems. If you are still having problems
after reviewing these solutions, please contact your service provider.
Power & Battery
Problem
Solutions
• Soft reset the device with the Stylus.
I can not turn on
my device.
• Connect your device to the AC adapter and check
LED indicator whether device is charging. Possibly
the battery is drained off.
Your device is designed by default to turn itself off if
not used for 3 minutes. This period can be adjusted to
a maximum of 5 minutes. Refer to the Power setting in
the manual for more information.
My device keeps
turning itself off.
My device’s date
& time reset to
factory default if I
have removed or
replaced battery.
Always re-attache the battery immediately during
replacement. The data will lose if the battery is
removed for a long time.
Why my device
power reduce
faster than my
friend’s?
Battery consumption varies from user to user due to
the way it is being used. Devices set under specific
identical test conditions may be compared objectively.
ActiveSync
Problem
Solutions
• Make sure you have correctly installed the ActiveSync
software found on the Companion CD that came with
your device, and followed the instructions accordingly.
Restart your device or/and PC and try again.
ActiveSync
operation cannot
be performed or
connected.
• DO NOT plug in the USB cable before loading
ActiveSync.
Appendix | 181
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Solutions
• Make sure the ActiveSync cradle/cable is connected
securely.
• On you PC, make sure the Connection Settings are
correctly selected in File > Connection Settings of
Microsoft ActiveSync.
Make sure your have established a Partnership with
the PC, and check Tools > Options of Microsoft
ActiveSync on your PC, to see if the information type
you want has been selected for synchronizing. For
more information, refer to Chapter 4.
ActiveSync is
connected, but I
can not transfer
data.
Display & Sound
Problem
Solutions
Screen freezes or
no response.
Soft reset your device by pressing Reset button with
the Stylus.
• Check the Sounds settings by tapping Start >
Settings > Personal tab >Sound & Notifications.
My device doesn’t
make any sound.
• Check the Volume Control, the speaker may be
muted.
What type of
extension files
can set up for
Alarm tone?
The format is *.wav, and should be located under
\Windows.
• Make sure the jack is clean and free from foreign
particle.
My device’s sound
only can be heard
from the headset.
• Re-insert the headset plug into the Audio Jack and
then unplug it may help sometimes.
• Make sure the headset is supplied with the device.
182 | Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection & Bluetooth
Problem
Solutions
• Make sure you have set up and connected to an
Internet Service Provider.
• Make sure the wireless connection to your mobile
Service Provider is switched on, and that the signal is
unobstructed.
I can not connect
to the internet;
Web surfing
doesn’t work.
• Verify with your Internet Service Provider that your
user name and password are correct.
Synchronization to a server allows your device to sync,
over-the-air (OTA) directly to a Microsoft Exchange
2003 Server. This allows you to update your e-mail,
contacts, calendar and tasks information securely from
any location with data connectivity. In order to use this
functionality, you do not need a PC running however it
does require your IT administrator to enable you to use
this service.
I can’t perform
over-the-air
synchronization.
• Transfer only one file, or no more than 25 contact
cards, at a time.
• Line up the IR ports so that they are unobstructed and
within close range.
Unable to use
Infrared (IR)
to transfer
• Make sure nothing is between the two IR ports.
• Adjust the room lighting. Some types of light interfere
with IR connections. Try moving to a different location
or turning off some lights. Do not try to use infrared
beaming in the sunlight.
information.
I can not end a
Bluetooth connection.
Turn Bluetooth connection off with Comm Manager.
• Make sure the Bluetooth function on the other device
is activated.
• Make sure you are within 10 meters of each other, and
there are no obstructions.
I can not find a
particular device.
•
Make sure the other device is set in “Discoverable” mode.
I can not connect to
the internet through
WiFi or ActiveSync
Please change the first connection setting from “MEdia
Net” to “My Work Network” or “My ISP”. (Start >
Settings > Connections > Connections > Advanced
(Desktop passthrough) > Select Networks > choose “My ISP”).
I can not connect
to the internet
through GPRS /
EDGE:
Please change the first connection setting from “My
Work Network” or “My ISP” to “MEdia Net”. (Start >
Settings > Connections > Connections > Advanced
> Select Networks > choose “Media Net”).
Appendix | 183
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection & Bluetooth (continued)
Problem
Solutions
After I create a new POP3
E-mail account, I cannot
retrieve email from this
account. The error message:
“Cannot connect to current
setting.”
In Messaging application, click Menu
> Tools > Options..., select the POP3
account you created. Go to fourth step (E-
mail Setup 4/4) and click “Options”. Change
Connection to Media Net.
Operating
Problem
Solutions
• You may have opened too many
programs. To release the operation load,
you can terminate unneeded running
programs by tapping Start > Settings
> System tab > Memory > Runnig
Programs.
My device operation
performs slowly.
• Reset your device by pressing Reset
button with the Stylus.
Memory
Problem
Solutions
A warning message about
“Running out of memory”
pops up on the screen.
Reset your device by pressing Reset button
with the Stylus.
• Delete any unnecessary files such as old
e-mail, image files, or large video files.
• Remove unneeded programs by selecting
Settings from the Start menu and then
Remove Programs.
Some ways to create space
on your phone are:
• Install the programs or store files onto the
miniSD card.
Media Player
Problem
Solutions
I can not move a file from one
folder to another in Windows
Media Player.
Use File Manager to move the file around
the device
184 | Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Solutions
What type of
• Video formats supported: *.wmv, *.asf, *.mp4, *.avi.
extension files can
Windows Media
Player play?
• Audio formats supported: *.wma, *.mp3, *.mid, *.midi,
*.rmi, *.amr, *.awb, *.m4a.
Phone
Problem
Solutions
• You may not located in network coverage area. Move
to coverage area and try again
My device can not
dial out or receive
calls.
• Make sure the phone is not in Flight Mode. Tab the
Antenna icon and turn off the Flight Mode.
Start entering the initial letters of the Contact you want
to call, and the system will automatically search and
sort the contact entries on the SIM card, in Contacts,
and the phone numbers in Call History (including
incoming, outgoing, and missed calls). Then, you can
select the desired number or contact from the filtered
list to dial.
How can I quickly
find a contact and
place a call?
• During a call, tap Speaker On, or press and
hold TALK until the speakerphone turns on. The
How do I enable
the Speakerphone’
function?
speakerphone icon (
) appears in the title bar.
• To turn off the speakerphone, tap Speaker Off, or
press and hold TALK again until the speakerphone
turns off.
• Make sure the SIM cards is installed properly.
Why is no signal
with SIM card
insertion?
• Network could be SIM locked. Contact your service
provider for assistance.
• Test your SIM in other phone, possibly the SIM card
is damaged.
Appendix | 185
Download from Www.Somanuals.com. All Manuals Search And Download.
A.4 Specifications
System Information
Processor
Memory
TI OMAP 850
- ROM : 128 MB
- RAM : 64 MB DDR SDRAM
Operating System Windows MobileTM Version 5.0
Display
LCD Type
2.8” transflective TFT-LCD with back-light LEDs, touch-
sensitive screen
Resolution
240 x 320 with 65,536 colors
Alignment Support Portrait and Landscape
GSM/EDGE Module
Functionality
Mode
GSM/EDGE (850, 900, 1800, and 1900)
Dual (GSM)
Yes
Internal Antenna
Camera Module
Type
CMOS 1.3Mega pixel with fixed lens
Resolution
1600x1280, 1280x1024 (SXGA), 640x480 (VGA),
320x240 (QVGA), 160x120 (QQVGA), 352x288 (CIF),
176x144 (QCIF)
Physical
Dimensions
Weight
109mm (L) x 58mm (W) x 23.7mm (T)
160g (with battery)
186 | Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Lights
Navigation
Buttons
- 5-way Navigation pad
- Five program buttons : Camera, Messaging, Internet
Explorer, Voice Command, Comm Manager
- Two phone functions : Call and End
- Two Soft Keys
- Volume control slider
- Power On/Off button
- Reset button
Keyboard
LEDs
QWERTY type, 41 keys
Bi-color LED on the right side: Green and Orange for
GSM standby, SMS message, GSM network status,
notification, battery charging status.
Bi-color LED on the left side: Blue and green for
Bluetooth system notification of powered-up and ready
to transmit radio frequency signal, and Wi-Fi status.
Audio
Audio Controller
AGC
Microphone/Speaker Built-in/Dual, Hands-free
Headphone
AMR/AAC/WAV/WMA/MP3 codec
Connection
Infrared
I/O port
IrDA SIR
USB, miniSD card slot with door(top)
External connector for GSM and EDGE
Stereo earphone/microphone jack
Antenna
Audio
Expansion Slots
miniSD Card
Yes
Appendix | 187
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring MMS message settings
Connection 187
Contacts 121
A.5 Index
A
Accessibility 149
ActiveSync 57
Audio 187
Cookies, Security Settings (Internet
Explorer) 88
B
D
Battery 17
Display 186
Drawing and Writing on the Screen
Bluetooth 61
C
E
Calendar 119
Calibration 19
Camera 186
Composing MMS messages from
F
188 | Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
Physical 186
Specifications 186
Synchronizing music, video, and
pictures 62
Synchronizing via Infrared and Blue-
tooth 60
Synchronizing with Exchange Server
R
T
Temporary Internet files, deleting
Transcriber 32
Troubleshooting Windows Media
Player 150
S
Searching 42
Security Settings (Internet Explorer)
Setting Date / Time / Language /
U
Uninstalling MIDlets/MIDlet suites
Setting pictures as Today back-
grounds 142
190 | Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
WEEE Notice
The Directive on Waste Electrical and Electronic Equipment (WEEE), which
entered into force as European law on 13th February 2003, resulted in a
major change in the treatment of electrical equipment at end-of-life.
The purpose of this Directive is, as a first priority, the prevention of WEEE,
and in addition, to promote the reuse, recycling and other forms of recovery
of such wastes so as to reduce disposal.
The WEEE logo (
) on the product or on its box indicates that this
product must not be disposed of or dumped with your other household
waste. You are liable to dispose of all your electronic or electrical waste
equipment by relocating over to the specified collection point for recycling
of such hazardous waste. Isolated collection and proper recovery of your
electronic and electrical waste equipment at the time of disposal will allow
us to help conserving natural resources. Moreover, proper recycling of the
electronic and electrical waste equipment will ensure safety of human health
and environment. For more information about electronic and electrical waste
equipment disposal, recovery, and collection points, please contact your
local city centre, household waste disposal service, shop from where you
purchased the equipment, or manufacturer of the equipment.
192 | Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
|
