R
Operator's Guide
T3204 and T3304 Series Label Printers
LP+t, IGP/PGL & IGP/VGL
Download from Www.Somanuals.com. All Manuals Search And Download.
T3204 and T3304 Series Label Printers
LP+t, IGP/PGL & IGP/VGL
Operator's Guide
P/N 136578–001, Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Warning and Trademarks
US and CANADA Radio Interference Note
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Properly shielded and grounded cables and connectors must be used in
order to meet FCC emission limits. The manufacturer is not responsible for
any radio or television interference caused by using other than
recommended cables and connectors or by unauthorized changes or
modifications to this equipment. Unauthorized changes or modifications
could void the user’s authority to operate the equipment.
The input/output (I/O) cable must be shielded for the printer to comply with
FCC rules and regulations Part 15 governing the radiation limits for Class “A”
equipment.
This digital apparatus does not exceed the Class A limits for radio noise
emissions from a digital apparatus set out in the radio interference regulations of
the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant
les limites applicables aux appareils numériques de la Classe A prescrites dans
le règlement sur le brouillage radioélectrique émis par le Ministère des
Communications du Canada.
WARNING
This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
Download from Www.Somanuals.com. All Manuals Search And Download.
Printronix, Inc. makes no representations or warranties of any kind regarding
this material, including, but not limited to, implied warranties of
merchantability and fitness for a particular purpose. Printronix, Inc. shall not
be held responsible for errors contained herein or any omissions from this
material or for any damages, whether direct, indirect, incidental or
consequential, in connection with the furnishing, distribution, performance or
use of this material. The information in this manual is subject to change
without notice.
This document contains proprietary information protected by copyright. No
part of this document may be reproduced, copied, translated or incorporated
in any other material in any form or by any means, whether manual, graphic,
electronic, mechanical or otherwise, without the prior written consent of
Printronix, Inc.
All rights reserved.
Trademarks
Printronix is a registered trademark of Printronix, Inc.
IGP is a registered trademark of Printronix, Inc.
LinePrinter Plus is a trademark of Printronix, Inc.
HP is a registered trademark of Hewlett–Packard Company.
PCL is a trademark of Hewlett–Packard Company.
Code V is a trademark of QMS, Inc.
QMS is a registered trademark of Quality Micro Systems, Inc.
IBM is a registered trademark of International Business Machines Corp.
17500 Cartwright Road, P.O. Box 19559
Irvine, California 92713
Telephone (714) 863–1900 FAX (714) 660–8682
Technical Support (714) 221–2686
COPYRIGHT
1997, PRINTRONIX, INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
About this Operator's Guide
This guide covers basic operating
procedures for the Printronix . T3204
and T3304 label printers. Printronix
wants you to feel comfortable and
confident using the T3204 and T3304
label printers, and this guide.
The guide has been designed to meet
the needs of all users, from beginners to
those experienced with thermal printers.
All text and illustrations refer to both
T3204 and T3304 printers except when
noted.
Follow the directions in this guide
along with those in your Setup
Guide in order to avoid injury to you
and damage to the printer
.
Conventions
Notes, Cautions, and Warnings
Notes provide supplemental information
note
caution
warning
that could affect printer operation or use.
Cautions describe conditions that could
damage the printer
.
Warnings describe conditions that could
harm you as well as damage the
equipment.
Message Display
These boxes show display messages as
they appear on the printer.
PAPER EMPTY
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
BASIC OPERATING PROCEDURES
Powering on the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Primary Operator Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printing Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
5
6
Loading Media
.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unloading Media
.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Installing the Ribbon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Removing the Ribbon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
INITIAL SETUP
Selecting Print Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Selecting Gap Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Setting Print Intensity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Selecting Media Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
.
Selecting the Ribbon Saver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
TROUBLESHOOTING
Cleaning the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Fault Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Table of Contents
i
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Powering On the Printer
caution
Before powering on the printer, make
sure it is plugged into the appropriate
power source.
Refer to the “Select a Site” section in
Chapter 2 of the Setup Guide for
information on proper power sources.
The power switch is located on the lower
right–hand corner of the rear of the printer. It
is marked f for power OFF and | for power
ON.
AC Power
Switch
For help with diagnosing printer problems,
printer self–test routines are automatically
run during the power–on cycle. Further
diagnostic tests can be performed using the
secondary operator panel functions. They
are covered in detail in the Setup Guide.
AC Power
Connector
Fuse
Holder
Using the Primary Operator Panel
Use the primary operator panel to perform
routine operations. The panel contains three
operator-accessible keys and three indicator
lights, used to control and indicate printer
status.
Message
Display
Primary
Control
Panel
note
The functions and meanings of some of the
keys and indicators on the primary operator
panel will change depending on the
firmware installed. This manual describes
printer operation with Printronix LP+,
IGP/PGL or IGP/VGL emulation firmware
installed. If your printer has Printronix
IGP/FGL emulation firmware, please refer
to the T3306 and T3308 Label Printers
Operator’s Guide, p/n 136452–001.
Message
Display
Contrast
Adjust
There is also a secondary operator panel,
consisting of a message display and six
keys. This panel is used to configure the
printer and to run self–tests, via the
configuration menus.
Secondary
Control
Panel
Operator’s Guide
1
Download from Www.Somanuals.com. All Manuals Search And Download.
using the primary operator panel
Selections from the main menu will need to
be changed when changes in the print mode,
media size, options and various other
configuration items are required for the
printer. Instructions begin on page 23 of this
guide.
note
Refer to the “Configuring the Printer”
chapter in the Setup Guide for complete
instructions in how to access and use the
secondary operator panel.
The following pages describe the status
indicator lights and keys comprising the
primary operator panel, along with the
related operating modes.
Status Indicator Lights
ON LINE/
PAUSE
The three status indicator lights (LEDs)
provide information about current printer
operation, as follows:
RIBBON
MEDIA
• POWER — Lit when the printer is
powered on.
• ON LINE/PAUSE — Lit when the printer is
on line or blinking when the printer is off
line or in a standby/fault state.
POWER
• RIBBON MEDIA — Lit when the printer
sensors fail to detect label media or the
presence of a ribbon.
Keys
Three primary operator panel keys provide
for the basic, day-to-day control of the
printer, as described on the following pages.
2
Operator’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
using the primary operator panel
CANCEL
Function Cancels all jobs, if pressed when
the printer is off line and not in a
fault state. Also clears faults and
puts the printer in the off line
mode.
CANCEL
Action
With the printer off line, cancel the
current run of labels by pressing
once.
Also, if a fault condition persists,
press once to clear fault.
Result
The printer will then cancel all
jobs and clear all imaged and
buffered data.
Or, in the case of fault clearing,
the printer will go off line without
canceling jobs.
note
Pressing the CANCEL key has no effect
when the printer is on line and running.
FEED
FEED
Function Prints any labels that have been
imaged and also the current label
in progress.
Action
With the printer off line, press
once to print labels.
Result
The printer will print any labels
that have been imaged and also
the current label in progress.
note
If no label is being processed, a blank page
will print.
Operator’s Guide
3
Download from Www.Somanuals.com. All Manuals Search And Download.
using the primary operator panel
ON LINE/PAUSE
ON LINE/
PAUSE
Function Temporarily stops the printing of
labels and controls the on line/
off line status of the printer.
Action To pause the printer, press once.
The on line/pause indicator will
blink.
To place the printer in the on line
mode, press once. The on line/
pause indicator will light.
Result
When the printer is paused, the
print mechanism will stop when
printing of the current label is
completed. All data will be held in
memory.
When the printer is in the on line
mode, the remaining labels in the
batch will be printed.
4
Operator’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Modes
The printer is capable of printing in either of
two modes:
• Direct Thermal only
(T3204–20 and T3304–20)
• Direct Thermal and Thermal Transfer
(T3204–21 and T3304–21)
The two modes have in common the
application of heat to produce the printed
image.They differ in the way the heat is
applied.
In thermal transfer printing, the individual dot
elements of the printhead apply heat to a
ribbon. The ink on the ribbon is a specially
formulated material that melts onto the print
media, bonding with the media to produce an
image.
Direct thermal printing does not use a ribbon.
Instead, the printer applies heat directly to
the print media, which reacts to the heat by
turning black.
note
All illustrations reflect the direct thermal and
thermal transfer printer configuration
(T3204–21 and T3304–21).
This mode requires the use of a special
direct thermal print media. It also requires
that the ribbon be removed, if already
installed.
note
Using direct thermal print media with a
ribbon installed will produce unacceptable
print quality
.
The desired mode is selected through the
printer menu system. The main menu is
accessed via the secondary operator panel.
note
Refer to the “Configuring the Printer”
chapter in the Setup Guide for complete
instructions in how to access and use the
secondary operator panel.
Operator’s Guide
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading Media
Media
Supply
Window
The printer accepts a wide range of media. It
can be loaded with roll–fed, fan–folded, or
die–cut continuous media of either thermal
transfer or direct thermal type. Media width
can range from 0.75 inches (19.1 mm) to
4.65 inches (118.1 mm). Media thickness
can range from 0.0025 inches (0.0635 mm)
to 0.01 inches (0.254 mm).
Use the following procedures to load media
of various kinds into the printer.
1
Press ON LINE/PAUSE to place the
Media
Supply Door
printer in the off line mode.
Open the media supply door.
2
3
Rotate the printhead latch
counterclockwise to unlatch, and raise
the printhead to an upright position.
Lower the hinge plate down. Slide the
media guide to the outer edge, and
rotate it to the down position.
Media
Guide
Printhead
Latch
Hinge
Plate
4
5
If you are loading fan–folded media,
skip the next step and go on to step 6.
To load roll–fed media, continue as
follows:
6
Operator’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
loading media
note
Printers have been built with two types of
standard media hubs: metal and plastic.
From the diagrams below, follow the media
loading instructions which match your
printer.
note
Do not use the media retainer if the media
supply roll is wider than 4 inches.
METAL HUB
a. If you are using media
with a 3” core, place the
3” media core adapters
on the media hub
assembly.
b. Place the media supply
roll on the media hub
assembly. Slide the media
retainer against the
supply roll and tighten the
thumb screw.
PLASTIC HUB
a. Place the 3” media
supply roll on the media
hub assembly.
b. Slide the media
retainer against the
supply roll and tighten the
thumb screw.
c. Skip the next step and continue with
step 7.
Operator’s Guide
7
Download from Www.Somanuals.com. All Manuals Search And Download.
loading media
6
To load fan–folded media, proceed as
follows:
a. Place the media supply either behind
or beneath the printer, as shown.
Media Hub
Assembly
Media
Retainer
Make sure the media feeds freely
from the container.
b. Route the media through the rear
media loading slot.
c. Continue with step 7.
Hinge Media Edge
Plate Sensor
Adjust
Media
Guide
7
Route the media over the guide plate,
under the media sensor and over the
platen roller (located beneath the
printhead).
Fanfold Media
8
9
Rotate the media guide up, and slide it
to the edge of the media.
Continue feeding the media under the
printhead until the media exits the
printhead assembly.
Slide the media forward, until it extends
beyond the printer front slot. Ensure that
all media guides are adjusted to the
width of stock being used.
8
Operator’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
loading media
10 If the media you are loading is of the
same width as the current media, skip
the next step and go on to step 12.
11 If you are loading media that is of a
different width from the current media,
you may need to adjust print quality as
follows:
note
The printer is aligned at the factory with
4–mil–thick label stock, whose width is
the maximum width accepted by the
printer.
a. Raise the hinge plate, and lower the
printhead by rotating the printhead
latch clockwise to the latched
position.
Media
Guide
Printhead
Latch
Hinge
Plate
b. Press ON LINE/PAUSE to enable
printing.
c. Send a sample test print file from the
host, or run the internal diagnostic
test file.
note
It may be necessary to feed several
labels before proper alignment of the
media occurs.
d. If the print quality is acceptable, go
on to step 12.
e. Otherwise, press ON LINE/PAUSE
again to place the printer in the of
f
line mode.
note
Although the head leveling knob can be
adjusted during printing, it is
recommended that this adjustment be
done while the printer is paused.
Operator’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
9
loading media
f. Pull the head leveling knob outward,
and rotate it one detent. Rotating the
knob clockwise from position 1 will
adjust the printer for media that is
narrower than the maximum width
accepted by the printer. When the
head leveling knob is rotated
clockwise from the detent position
just before position 1 to position 1,
the printhead will return to the
maximum media width position.
Head Leveling Knob
note
Each of the 18 positions on the head
leveling knob will raise or lower the
printhead 0.003 inches (0.076 mm),
giving a maximum adjustment range of
0.054 inches (1.37 mm).
g. Return to step a and repeat until you
obtain the desired print quality.
12 If you do not intend to use the optional
media rewind hub, skip the next step
and go on to step 14.
note
Use the rewind hub to print quantities of
labels in single batches, for later use. The
hub automatically rolls up the label media
for convenient handling. It is also used with
the automatic label peel-off dispenser
option to roll up the media backing after
labels have been peeled off.
10
Operator’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
loading media
13 To use the media rewind hub, complete
the following procedure.
a. Lower the lower right-hand front
panel.
b. Remove the arc plate from its stored
position, and install on the front of
the printer.
Route the media around the arc
plate and to the media rewinder.
c. Place the clasp over the end of the
media, and rotate the media
rewinder a few turns.
Rotate the media guide up, and slide
it to the media edge.
d. Lift and snap the lower right-hand
front panel closed.
Continue with step 14.
14 Raise the hinge plate, and lower the
printhead by rotating the printhead latch
clockwise to the latched position.
15 Close the media supply door.
16 Press ON LINE/PAUSE to enable
printing.
note
It may be necessary to feed several labels
before proper alignment of the media
occurs.
Operator’s Guide
11
Download from Www.Somanuals.com. All Manuals Search And Download.
loading media
17 The peel-and-present option allows for
on-demand label dispensing. Although
the peel-and-present mechanism is
included with every printer, the label
present sensor and internal rewind
options are required to use this feature.
To use the optional peel-and-present,
follow the instructions outlined below.
a. Turn off the printer, and open the
side access cover.
b. Rotate the printhead latch
counterclockwise to raise the
printhead.
c. Lower the hinge plate and the lower
front panel.
d. Using a Philips screwdriver, remove
the tear bar, invert it (flip it over), and
reinstall it.
e. Place the media supply roll on the
media hub assembly. Slide the
media retainer against the supply
roll, and tighten the thumbscrew.
f. Route the media over the guide
plate, through the media sensor, and
over the platen roller (located
beneath the printhead).
12
Operator’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
loading media
g. Route the media liner (backing)
around the tear bar to the media
rewinder.
h. Place the clasp over the end of the
media, and rotate the media
rewinder a few turns.
i. Rotate the media guide up, and slide
it to the media’s edge.
j. Lift and snap the lower right front
panel closed.
k. Raise the hinge plate, and latch the
printhead by rotating the printhead
latch clockwise to the latched
position.
l. Close the side cover.
note
It is possible to use the present
sensor only (without inverting the
tear bar) to provide on-demand
label printing in the tear-off mode.
To operate in this mode, media
should be routed as shown in
step f, and the Label Present
menu selection should be
enabled.
Operator’s Guide
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Unloading Media
Media
Supply
Window
Use the following procedure to unload media
from the printer.
1
Press ON LINE/PAUSE to place the
printer in the off line mode.
Open the media supply door.
2
3
4
Rotate the printhead latch
Media
Supply Door
counterclockwise to unlatch, and raise
the printhead to an upright position.
Lower the hinge plate down. Slide the
media guide to the outer edge, and
rotate it to the down position.
Cut the media either before or after the
front slot, depending on whether or not
the rewind hub is being used.
note
If the media rewind hub was being used,
you may choose to continue winding the
media onto the hub or to roll it back onto
the supply roll (media hub).
Media
Guide
Printhead
Latch
Hinge
Plate
5
If the installed media is fan–folded, skip
the next step and go on to step 7.
Otherwise, continue with step 6.
14
Operator’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
unloading media
6
To remove roll–fed media, proceed as
3–Inch Core
Adaptors
follows:
Media Hub
Assembly
a. Roll the media onto the media hub or
onto the rewind hub, as appropriate.
b. If you have rolled the media onto the
media hub, slide the roll of media of
f
Thumbscrews
Media
the hub.
Supply Roll
c. If you have rolled the media onto the
rewind hub, lower the lower
right-hand front panel.
Media Hub
Assembly
Media
Retainer
Unroll the media from the hub, and
remove the clasp
d. Lift and snap the lower right-hand
front panel closed.
Rewind Hub
7
To remove fan–folded media, proceed
as follows:
a. If the rewind hub was not being
used, simply pull the media through
the loading slot and out of the
printer.
Go on to step 8.
b. If the rewind hub was being used,
finish rolling the media onto the hub.
Operator’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
15
unloading media
Lower the lower right-hand front
panel.
c. Unroll the media from the hub, and
remove the clasp.
d. Lift and snap the lower right-hand
front panel closed.
Rewind
Hub
Right-Hand
Front Panel
Continue with step 8.
8
9
Raise the hinge plate, and lower the
printhead by rotating the printhead latch
clockwise to the latched position.
Close the media supply door.
Hinge
Plate
Printhead
Latch
16
Operator’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Ribbon
Media
Supply
Window
As noted previously, when printing in thermal
transfer mode, the printer requires a ribbon.
Use the following procedure to install a new
ribbon.
note
The thermal transfer mode is selected
through the printer menu system. The main
menu is accessed via the secondary
operator panel. Refer to the “Configuring
the Printer” chapter in the Setup Guide for
complete instructions in how to access and
use the secondary operator panel.
Media
Supply Door
1
Press ON LINE/PAUSE to place the
printer in the off line mode.
2
3
Open the media supply door.
Rotate the printhead latch
counterclockwise to unlatch, and raise
the printhead.
Lower the hinge plate.
4
Place the new ribbon supply roll on the
supply hub.
Printhead
Latch
Hinge
Plate
Operator’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
17
installing the ribbon
Ribbon Supply Roll
Supply Hub
Take-Up Hub
J-Hook
Make sure the ribbon roll is pushed up
against the hub flange.
5
6
Route the ribbon to the take-up hub, as
shown.
While holding the ribbon take-up hub,
rotate the J-hook clockwise to unlatch it.
18
Operator’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
installing the ribbon
7
8
Raise the J-hook upward, and place the
end of the ribbon over the take-up hub.
Slide the J-hook back into place, as
shown. While holding the ribbon take-up
hub, rotate the J-hook counterclockwise
to latch.
Turn the take-up hub until all the ribbon
slack is removed.
9
Raise the hinge plate, and lock the
printhead by rotating the printhead latch
clockwise.
Printhead
Latch
Hinge
Plate
10 Close the media supply door.
11 Press ON LINE/PAUSE to enable
printing.
J-Hook
Take-Up Hub
Ribbon
Operator’s Guide
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the Ribbon
Generally, ribbons are used to completion
and then replaced. Removal of the old ribbon
is simply a matter of pulling it off the take–up
hub and discarding it.
However, there may be times when the use
of direct thermal media is required and an
installed ribbon has not been completely
used up. (As noted previously, when printing
in direct thermal mode, the printer does not
use a ribbon.)
In this case, use the following procedure to
remove the ribbon.
Media
Supply
Window
note
The direct thermal mode is selected
through the printer menu system. The main
menu is accessed via the secondary
operator panel. Refer to the “Configuring
the Printer” chapter in the Setup Guide for
complete instructions in how to access and
use the secondary operator panel.
1
Press ON LINE/PAUSE to place the
printer in the off line mode.
Media
Supply Door
2
Open the media supply door.
20
Operator’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
removing the ribbon
Ribbon Supply Roll
Supply Hub
Take-Up Hub
J-Hook
CUT
Printhead
3
4
Cut the ribbon anywhere between the
take-up hub and the printhead.
Rotate the printhead latch
counterclockwise to raise the printhead,
and then lower the hinge plate.
5
While holding the ribbon take-up hub,
rotate the J-hook clockwise to unlatch it.
Operator’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
21
removing the ribbon
6
Slide the used ribbon off the hub, and
dispose of it.
7
Turn the ribbon supply hub clockwise to
draw the unused portion of the ribbon
back onto the supply roll.
note
You may leave the unused portion of the
ribbon in place until the next thermal
transfer print job, at which time you may
reinstall it by following the ribbon
installation procedure.
8
Raise the hinge plate, and lock the
printhead by rotating the printhead latch
clockwise.
9
Close the media supply door.
Printhead
Latch
Hinge
Plate
10 Press ON LINE/PAUSE to enable
printing.
22
Operator’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting Print Mode
PRINT MODE selects the printing mode of
the printer. Selecting DIRECT THERMAL
MODE activates direct thermal printing mode
(ribbon must not be installed). Selecting
THERMAL XFER activates thermal transfer
printing mode (ribbon required).
OFFLINE
IGP/PGL
1
2
Press ON LINE/PAUSE to place the
printer in the off line mode.
PAPER CONTROL
Page Width
Press
twice to enter the paper
until the print mode
control menu.
PAPER CONTROL
Print Mode
3
4
5
Press
menu is displayed.
Print Mode
Thermal Xfer *
Press
menu.
to enter the print mode
Print Mode
Thermal Xfer *
Print Mode
Direct Thermal
Press
to select between
thermal transfer and direct thermal print
methods.
Print Mode *
Direct Thermal
6
7
Press ENTER to select the option.
ONLINE
IGP/PGL
Press ON LINE/PAUSE to place the
printer in the on line mode.
Operator’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Selecting Gap Sensor
GAP SENSOR selects the type of media
used for printing. The options for this
selection are as follows:
• TRANSMISSIVE (see–through)
• REFLECTIVE (black stripe)
• NONE (default)
1
Press ON LINE/PAUSE to place the
OFFLINE
IGP/PGL
printer in the off line mode.
USER CONFIG
PAPER CONTROL
2
3
4
5
Press
Press
Press
to enter the configuration menus.
to reach the printer control menu.
to enter the printer control menu.
to reach the gap sensor
USER CONFIG
PRINTER CONTROL
PRINTER CONTROL
Media Handling
Press
menu.
PRINTER CONTROL
Gap Sensor
6
7
Press
Press
to enter the gap sensor menu.
to view the desired setting.
Gap Sensor
None *
Gap Sensor
None *
Gap Sensor
Reflective
Gap Sensor
Transmissive
Gap Sensor
Reflective *
8
9
Press ENTER to select the setting.
Press ON LINE/PAUSE to place the
ONLINE
IGP/PGL
printer in the on line mode.
24
Operator’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Print Intensity
The PRINT INTENSITY adjustment is used
to balance a new printhead, so that it prints
at the same level of darkness as did the
previous head. You can specify intensity
values from –10 through +10. The factory
default setting is 0.
OFFLINE
IGP/PGL
1
Press ON LINE/PAUSE to place the
printer in the off line mode.
USER CONFIG
PAPER CONTROL
2
Press
to enter the configuration
to reach the printer control
to enter the printer control
to reach the print
menus.
USER CONFIG
PRINTER CONTROL
3
4
5
6
7
Press
menu.
PRINTER CONTROL
Media Handling
Press
menu.
Press
PRINTER CONTROL
Print Intensity
intensity menu.
Press
menu.
to enter the print intensity
Print Intensity
0*
Press
value.
to select the desired
Print Intensity
–10
Print Intensity
0*
Print Intensity
10
Print Intensity
–3
8
9
Press ENTER to select the setting.
ONLINE
IGP/PGL
Press ON LINE/PAUSE to place the
printer in the on line mode.
Operator’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Selecting Media Handling
The options for this selection are as follows:
• SELF STRIP – selects the self strip option.
When the label present sensor is
installed and enabled, the printer can
be configured for “one up” printing.
• CUTTER selects the cutter mechanism
option.
The cutter must be installed to use this
option.
• TEAR OFF –selects the tear off option.
• CONTINUOUS – selects the continuous
feed option.
OFFLINE
IGP/PGL
1
2
Press ON LINE/PAUSE to place the
printer in the off line mode.
USER CONFIG
PAPER CONTROL
Press
to enter the configuration
to reach the printer control
to enter the printer control
menus.
USER CONFIG
PRINTER CONTROL
3
4
Press
menu.
PRINTER CONTROL
Media Handling
Press
menu.
26
Operator’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
selecting media handling
Media Handling
Continuous *
5
6
Press
menu.
to enter the media handling
to view the desired
Media Handling
Continuous
Press
option.
Media Handling
Tear Off
Media Handling
Cutter
Media Handling
Self Strip
7
8
Press ENTER to select the desired
Media Handling
Self Strip *
option.
ONLINE
IGP/PGL
Press ON LINE/PAUSE to place the
printer in the on line mode.
Operator’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Selecting the Ribbon Saver
RIBBON SAVER selects the ribbon saver
option, if the ribbon saver is installed.
1
2
Press ON LINE/PAUSE to place the
OFFLINE
IGP/PGL
printer in the off line mode.
Press
to enter the configuration
to reach the printer control
to enter the printer control
to reach the ribbon
USER CONFIG
PAPER CONTROL
menus.
3
4
5
6
7
Press
menu.
USER CONFIG
PRINTER CONTROL
PRINTER CONTROL
Media Handling
Press
menu.
PRINTER CONTROL
Ribbon Saver
Press
saver menu.
Ribbon Saver
Disable *
Press
menu.
to enter the ribbon saver
to view the desired
Ribbon Saver
Disable *
Press
option.
Ribbon Saver
Enable
Ribbon Saver
Enable *
8
9
Press ENTER to select the option.
Press ON LINE/PAUSE to place the
ONLINE
IGP/PGL
printer in the on line mode.
28
Operator’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning the Printer
Keeping the printer clean will help ensure
efficient operation and good print quality.
Media
Supply
Window
warning
Disconnect the AC power cord before
cleaning the printer
.
Cleaning the Outside of the Cabinet
Clean the outside of the cabinet with a soft,
lint–free cloth and mild detergent
(dishwashing liquid works well). Do not use
abrasive powders or chemical solvents.
Clean the window with plain water or a mild
window cleaner.
Media
Supply Door
caution
Always apply the cleaning solution to
the cloth; never pour cleaning solution
directly onto the printer
.
Cleaning Inside the Cabinet
Over time, it is normal for dust, particles of
paper, and ink to accumulate inside the
printer. Paper dust and ink build–up must be
removed periodically to avoid degraded print
quality. To clean the interior of the printer,
perform the following steps.
caution
To avoid damage to the printer, be
extremely careful when vacuuming and
dusting around the printhead and
surrounding areas.
1
Power–off the printer and unplug the
power cord.
2
3
Unload the media supply (page 14).
Remove the ribbon, if installed
(
page 20).
Operator’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
29
cleaning the printer
4
Using a soft–bristled, non–metallic
brush, remove dust particles from the
media path, ribbon guides and ribbon
path.
Cotton Swab
5
6
Brush and vacuum accumulated dust or
residue, especially in the printhead
areas.
Using a cloth dampened with
anhydrous alcohol, clean the ribbon
guides, rollers and mechanical
assemblies.
Printhead
Element
7
The printhead will require cleaning after
extended normal operation. Regular
cleaning will ensure the highest print
quality. Clean the printhead using a
clean cotton swab and anhydrous
alcohol.
Hinge
Plate
Printhead
Printhead
Latch
8
9
When the cutter or tear bar become dirty
with gummed media backing, clean the
area using a clean, lint–free cloth and
anhydrous alcohol.
Wipe the cabinet interior with a clean,
lint–free cloth damp (not wet) with water
and mild detergent, or spray the
surfaces lightly with window cleaning
solution.
10 Dry the interior with a dry, clean,
lint–free cloth.
11 Reload the media (page 6) and ribbon
(
page 17).
30
Operator’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Fault Messages
If a printer fault occurs, a specific message
appears in the message display. When this
happens, correct the fault immediately.
You can correct most faults by performing a
simple procedure, such as clearing a media
jam or reloading media or ribbon. For more
serious faults, however, call an authorized
Printronix service representative.
PROM Fault
PROM FAULT
Power–up initialization test detected a
PROM failure. Contact your authorized
service representative.
RAM Fault
RAM FAULT
Power up initialization test detected a RAM
failure. Contact your authorized service
representative.
RTC RAM Fault
RTC RAM FAULT
The RTC non–volatile RAM failed the
checksum test. Contact your authorized
service representative.
Printhead Control Fail
PRINTHEAD
Thermal printhead control circuit failed.
Contact your authorized service
representative.
CONTROL FAIL
A–D Converter Fail
A–D CONVERTER
FAIL
Analog–to–digital converter failed. Contact
your authorized service representative.
Operator’s Guide
31
Download from Www.Somanuals.com. All Manuals Search And Download.
fault messages
Paper Jam
PAPER JAM
Possible causes:
• Improper media.
• Actual label length greater than
programmed label length.
Paper Empty
PAPER EMPTY
MEDIA FAULT
Printer is out of media stock.
Media Fault
The ribbon system detected a fault.
Possible causes:
• Out of ribbon.
• Ribbon motion was stopped.
• Obstructions in the media movement.
• Paper motion stopped.
Cutter Fault
CUTTER FAULT
The cutter operation failed.
Possible causes:
• Cutter is jammed.
• Defective cutter hardware.
Ribbon Saver Fault
RIBBON SAVER FAULT
Ribbon saver operation failed.
Possible causes:
• Obstruction in ribbon area.
• Defective ribbon saver hardware.
Printhead Test Fail
PRINTHEAD
TEST FAIL
The printer has detected a failure in one or
more printhead dots.
32
Operator’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
PRINTRONIX
17500 CARTWRIGHT ROAD
P.O. BOX 19559
IRVINE, CA. 92623-9559
PHONE: 714/863-1900
FAX: 714/660-8682
PRINTRONIX
NEDERLAND BV
P.O. BOX 163, NIEUWEWEG 283
NL-6600 AD WIJCHEN
THE NETHERLANDS
PHONE: (31) 24-6490111
FAX: (31) 24-6419768
PRINTRONIX A.G.
42 CHANGI SOUTH
STREET 1
CHANGI
SOUTH INDUSTRIAL ESTATE
SINGAPORE 486763
PHONE: (65) 542-0110
FAX: (65) 543-0220
VISIT OUR WEBSITE AT:
136578–001B
Download from Www.Somanuals.com. All Manuals Search And Download.
|