HP Hewlett Packard Network Card A7011A User Manual

A7011A/A7012A  
PCI-X  
2-Port Gigabit Ethernet Cards  
on  
HP-UX 11i v 1.0 and 11i v 2.0  
Release Notes  
Software Versions B.11.11 and B.11.23  
Manufacturing Part Number : J6371-90004  
E0304  
U.S.A.  
© Copyright 2004 © Hewlett-Packard Development Company L.P.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Release Notes for PCI-X 2-Port Gigabit Ethernet Cards  
What’s in this Version  
Release Notes for PCI-X 2-Port  
Gigabit Ethernet Cards  
What’s in this Version  
The following information is for the initial release of HP’s PCI-X 2-Port Gigabit Ethernet  
cards for HP-UX 11i v 1.0 (version B.11.11) and HP-UX 11i v 2.0 (version B.11.23). The  
information here applies to the A7011A (1000Base-SX--fiber-based) card and A7012A  
(1000Base-T--copper-based). HP-UX 11i v 1.0 is for PA-RISC-based machines. HP-UX 11i v 2.0  
is for Itanium2-based machines.  
The Gigabit Ethernet software bundle (IEther-00) for HP-UX 11i v 1.0 is on the December  
2003 application CD. The Gigabit Ethernet software bundle (IEther-00) for HP-UX 11i v 2.0  
is on the March 2004 application CD. You can check to see if these drivers are present on your  
system by running the commands described in “How to Verify that the Correct Driver is in the  
Kernel” in this document.  
For the most up-to-date list of network cards and the systems that they work on, check the  
Card, Driver, Version matrix on http://docs.hp.comunder “Networking and  
Communications,” or ask your sales representative.  
Features  
Each A7011A and A7012A PCI-X 2-Port Gigabit Ethernet card has the following features:  
PCI-X operation in 133 MHz, 64-bit-compatible mode. Note: the cards can also operate in  
PCI mode and so can be put in a PCI slot. This will of course affect performance.  
Supports HP-UX 11i v 1.0 (64 bit) on PA-RISC platforms and HP-UX 11i v 2.0 on  
Itanium2platforms.  
Supports the following PA-RISC systems:  
— Superdome (or Superdome with IO Expansion (IOX) cabinet). Includes new 64-way.  
— rp8420 (base system or base system and I/O Expansion (IOX) cabinet),  
rp8400 (base system or base system and I/O Expansion (IOX) cabinet).  
— rp7420, rp7410.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Release Notes for PCI-X 2-Port Gigabit Ethernet Cards  
What’s in this Version  
— rp4440, rp3440.  
Supports the following Itanium2systems:  
— Superdome (or Superdome with IO Expansion (IOX) cabinet). Includes new 64-way.  
— rx8620 (base system or base system and I/O Expansion (IOX) cabinet).  
— rx7620.  
— rx5600.  
— rx2600.  
Supports Ignite-UX.  
On the A7011A, the 1000Base-SX port operates only at 1000 Mbit/s and only in  
full-duplex mode. It autonegotiates flow control but not speed or duplexity.  
Ensure that the 1000 Mbit/s port on the interfacing switch is set for autonegotiation or  
1000Mbit/s full-duplex mode.  
On the A7012A, the 1000Base-T port operates at 10 or 100 Mbit/s in either full- or  
half-duplex modes and at 1000 Mbit/s only in full-duplex mode.  
Ensure that you set both your switch and the gigabit Ethernet port on the card to  
autonegotiation or set both to the same speed and duplex mode  
The Gigabit Ethernet cards support use of Jumbo Frames. The maximum transmission  
unit (MTU) for using jumbo frames with the iether driver on HP-UX 11i v 1.0 or v 2.0 is  
in the range of 1501 to 9000 bytes.  
The Gigabit Ethernet LAN software supports TCP/IP, NFS, and DLPI applications.  
Ethernet and SNAP encapsulations are supported.  
Support interrupt migration.  
Support HP ServiceGuard.  
Support vPars.  
Support virtual LANs (VLANs).  
Support PCI-X/PCI online addition/replacement (OLA/R) on supported systems.  
The 1000Base-SX A7011A has two duplex LC connectors and two LEDs--one LED for each  
port. Each LED flashes to indicate Activity (data traffic) and is solid to indicate the link is  
up.  
The 1000Base-T A7012A has two RJ-45 ports. Each port has an activity/link LED and a  
speed LED that is off for 10 Mbit/s, green for 100 Mbit/s, or yellow for 1000 Mbit/s.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Release Notes for PCI-X 2-Port Gigabit Ethernet Cards  
Overview of Software Installation Process  
Overview of Software Installation Process  
The required operating environment is either HP-UX 11i v 1.0 or v 2.0 depending on whether  
you are installing to a PA-RISC-based machine (11i v1.0) or to an Itanium2-based machine  
(HP-UX 11i v 2.0). To install the Operating Environment, use the Ignite-UX-11-11  
Installation Utilities available on the HP-UX 11i v 1.0 (or 2.0) OE or AR media. The operating  
environment version should show as B.11.11 or B.11.23 when you type: uname -aat the  
system prompt.  
For instructions on how to install and configure the A7011A and A7012A hardware and  
software, refer to the PCI-X 2-Port Gigabit Ethernet Card for HP-UX 11i v 1.0 Installation  
Guide available on the web at http://docs.hp.com under “Networking and Communications.”  
If the A7011A or A7012A card was factory installed (ordered on product option 0D1) or is the  
“built-in” or “core” LAN, the LAN driver for this card will already be on your system disk.  
If Installing HP-UX 11i v 1.0 from the December 2003 OE or AR Media  
The December 2003 HP-UX 11i Operating Environment disk, or Application Software and  
Support Plus disks contain everything you need for HP-UX 11i v 1.0 (for PA-RISC-based  
machines).  
1. Using the December 2003 HP-UX 11i Operating Environment disk or Support Plus disk,  
load the HWEnable11i bundle. Load the HWEnable11i bundle before or with the driver  
bundles mentioned in the next step.  
2. Using the December 2003 HP-UX 11i Operating Environment disk or Application  
Software disk, load the latest required driver:  
Gigabit Ethernet driver (IEther-00 bundle version B.11.11.04).  
If Installing HP-UX 11i v 2.0 from the March 2004 OE or AR Media  
The March 2004 HP-UX 11i Operating Environment disk, or Application Software and  
Support Plus disks contain everything you need for HP-UX 11i v 2.0 (for Itanium2-based  
machines).  
1. Using the March 2004 HP-UX 11i Operating Environment disk or Support Plus disk, load  
the HWEnable11i bundle. Load the HWEnable11i bundle before or with the driver  
bundles mentioned in the next step.  
2. Using the March 2004 HP-UX 11i Operating Environment disk or Application Software  
disk, load the latest required driver:  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Release Notes for PCI-X 2-Port Gigabit Ethernet Cards  
How to Verify that the Correct Driver is in the Kernel  
Gigabit Ethernet driver (IEther-00 bundle version B.11.23.02).  
How to Verify that the Correct Driver is in the Kernel  
For instructions on how to install and configure the hardware and software, refer to the  
PCI-X 2-Port Gigabit Ethernet Card for HP-UX 11i V 1.0 Installation Guide available on the  
web at http://docs.hp.com under “Networking and Communications.”  
The required operating environment is HP-UX 11i v 1.0 or v 2.0. The operating environment  
version should show as B.11.11 or B.11.23 when you type: uname -aat the system prompt.  
The A7011A and A7012A cards require the iether driver from the IEther-00 bundle.  
To verify that the driver was loaded in the kernel, execute the following command:  
what /stand/vmunix | grep iether (for Gigabit Ethernet)  
You should see a response like:  
iether Version: 1 Jun 26 2003  
iether Revision: B.11.11.09 Jun 26 2003  
Known Problem  
The A7012A card does not interoperate with older switches containing a BCM 5400 PHY with  
a version earlier than C-5. The problem occurs when interfacing with older switches such as  
the HP Procurve Module J4115A (note: other switches might still have the BCM 5400 part).  
Procurve version J4115B fixes the Procurve problem.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Release Notes for PCI-X 2-Port Gigabit Ethernet Cards  
List of Related Documentation  
List of Related Documentation  
The following is a list of documents related to this product. They are available on the web at  
http://docs.hp.com under “Networking and Communications.” The Support Guide is also  
available on the Instant Information CD if you have an HP support contract.  
PCI-X 2-Port Gigabit Ethernet Card for HP-UX 11i v 1.0 and 2.0Installation Guide  
Provides step-by-step instructions on how to install and configure the hardware and  
software.  
Ethernet Support Guide  
Provides information on advanced features and detailed information on troubleshooting  
the combination Gigabit Ethernet cards.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Release Notes for PCI-X 2-Port Gigabit Ethernet Cards  
List of Related Documentation  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  

Greenheck Fan Ventilation Hood SSDFD 155 User Manual
Grizzly Grinder G0596 User Manual
Haier TV Receiver LE46D10F User Manual
Harbor Freight Tools Automobile Accessories 94318 User Manual
Healthrider Treadmill HRTL10980 User Manual
Honeywell Automobile Parts ML4105 User Manual
HP Hewlett Packard Printer StudioJet User Manual
H P Products Vacuum Cleaner 7161 User Manual
Husqvarna Blower 966629402 User Manual
Husqvarna Trimmer 326RX User Manual