Release Notes
hp StorageWorks
Data Replication Manager HSG80
ACS Version 8.7P
Product Version: ACS Version 8.7P
Fifth Edition (March 2004)
Part Number: AA-RPJ2E-TE
This document provides information for HP StorageWorks Data Replication Manager with HSG80 Array
Controller Software Version 8.7P that is not covered elsewhere in user documentation. Individuals responsible
for configuring, installing, and using the Data Replication Manager solution should refer to this document for
last-minute content.
For the latest version of these Release Notes and other Data Replication Manager documentation, access the
website at http://h18000.www1.hp.com/products/sanworks/drm/index.html. Click the technical documentation
link and the technical support page is displayed. Click manuals (guides, supplements, addendums, etc) for a
listing of related documentation.
Download from Www.Somanuals.com. All Manuals Search And Download.
Release Notes Contents
Release Notes Contents
These release notes cover the following major topics:
■
■
■
Data Replication Manager HSG80 ACS Version 8.7P Release Notes
3
Download from Www.Somanuals.com. All Manuals Search And Download.
What’s New
Intended Audience
This document is intended for customers who purchased or upgraded to the HP StorageWorks
Data Replication Manager (DRM) HGS80 Array Controller Software (ACS) Version 8.7P, and
for HP authorized service providers responsible for installing, configuring, and maintaining
DRM systems.
Related documentation
The following documents provide helpful information for running your DRM solution:
■
■
■
■
■
■
HP StorageWorks Data Replication Manager HSG80 Version 8.7P Configuration Guide,
part number AA-RPHZF-TE
HP StorageWorks Data Replication Manager HSG80 Version 8.7P Failover/Failback
Procedures Guide, part number AA-RPJ0E-TE
HP StorageWorks Data Replication Manager HSG80 ACS Version 8.7P Scripting User
Guide, part number EK-DRMSC-OA. E01
HP StorageWorks Data Replication Manager HSG80 ACS Version 8.7P Design Guide
Reference Guide, part number AA-RQ78C-TE
HP StorageWorks Continuous Access and Data Replication Manager SAN Extensions
Reference Guide, part number AA-RU5CE-TE
HP StorageWorks SAN Design Reference Guide, part number AA-RMPNL-TE
What’s New
The following sections summarize the major features, enhancements, and requirements of
using ACS Version 8.7P with DRM.
SAN Extension Products
Refer to the HP StorageWorks Continuous Access and Data Replication Manager SAN
Extensions Reference Guide for details on supported Fibre Channel over Internet Protocol
products. All WDM products are permitted with Continuous Access EVA and Data
Replication Manager.
Controller Firmware Upgrade Path
HP strongly recommends that the minimum version of DRM for new installations or upgrades
be ACS v8.7-3P. This version should be obtained from a direct install and not by overlaying
patches on earlier versions of 8.7P. For information on obtaining the appropriate ACS v8.7-3P
PCMCIA card, contact your HP service center.
The rolling upgrade is documented in the HP StorageWorks Data Replication Manager
HSG80 ACS Version 8.7P Configuration Guide. The procedure is designed to allow an array
controller software upgrade without the need for a server reboot. However, you must ensure
that all the latest drivers, and if applicable, the latest release of Secure Path are installed prior
to this upgrade. Installing the latest drivers may require the server to be rebooted. Information
4
Data Replication Manager HSG80 ACS Version 8.7P Release Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
What’s New
Operating System and Fibre Channel Switch Support
minimum hardware and software versions of items supported by those operating systems
compatible with Data Replication Manager running ACS v8.7P and subsequent updates.
Operating systems are listed by vendor in the left column. Each item in the same row, and
listed to the right, is supported by that operating system.
To use this table, select an operating system and operating system version, then move to the
right and select a Fibre Channel Adapter (FCA). Supported FCA firmware is located further to
the right, followed by the driver and Secure Path versions for the FCA. In the last column is a
brief statement about cluster support for that operating system and version.
Table 2 lists supported switches for the HSG80 controller with their approved version of
firmware when used for DRM. Be aware that a 2 Gb/sec switch is constrained by the HSG80
controller to 1 Gb/sec.
Table 1: Operating System Support Matrix
Operating
System
Adapter
Firmware
Adapter
Driver
Secure
Path
OS Version
FCA
Clustering
HP
11.0 (32-bit with
A5158A 1Gb PCI
A6685A 1Gb HSC
A6795A 2Gb PCI
Native
Native
3.0aSP1 or
3.0bSP1
ServiceGuard v11.14
Max: 4 nodes
HP-UX
0303 patch bundle)
11.11 (32-bit with
0603 patch bundle)
HP OpenVMS
7.2-2 with
VMS722_
FIBRE_SCSI-
V0400
LP8000 or
LP9002 (FCA2354)
3.81a4, 3.82a1,
3.91a1, or
3.92a0
Native
Native
VMSCluster
Max: 96 nodes
7.3 with
VMS73_
FIBRE_SCSI-
V0500
7.3-1 with
VMS731_
FIBRE_SCSI-
V0100
LP9802 (FCA2384)
1.00x8 or
1.81a1
HP Tru64
UNIX
5.1a BL22 PK4
5.1b BL1 PK1
LP8000 or
LP9002 (FCA2354)
3.81a4, 3.82a1,
3.91a1, or
3.92a0
Native
Native
TruClusters
Max: 8 nodes
LP9802 (FCA2384)
1.00x8 or
1.81a1
4.3.3, 5.1
Cambex 1Gb PCI
(1000F)
2.01.38
1.5.20.2
1.5.23.2
2.0c
2.0d
v5.1 supports
HACMP v4.5
IBM-AIX
Cambex 2Gb PCI
(2000F)
Data Replication Manager HSG80 ACS Version 8.7P Release Notes
5
Download from Www.Somanuals.com. All Manuals Search And Download.
What’s New
Table 1: Operating System Support Matrix (Continued)
Operating
Adapter
Firmware
Adapter
Driver
Secure
Path
System
OS Version
FCA
Clustering
Microsoft
4.0 SP6a
LP8000 (KGPSA-CB)
LP952 (FCA2101)
3.82a1
4.81a9
4.0c
NT - 2 nodes
Windows NT
(Intel)
BIOS 1.60a5
Windows 2000
Server - none
3.82a1
4.82a14
4.82a16
BIOS1.61a2
Windows 2000
Windows
2000
5.0 SP2, SP3, SP4
3.91a1
Advanced Server -
MSCS v1.1 & Oracle
9iRAC; Max: 2 nodes
BIOS1.63a1
(32-bit)
LP9002DC (FCA2355)
3.82a1 BIOS
1.61a2
4.82a9
4.82a14
4.82a16
Windows Server
2003, Enterprise
edition - MSCS &
Oracle 9iRAC; Max:
4 nodes
3.91a1 BIOS
1.63a1
QLA2340 (FCA2214)
or BL20P Mezzanine
card (not supported on
NT)
1.34
8.2.0.72
QLA2342
1.34
8.2.0.72
(FCA2214DC) or
BL20P Mezzanine card
(not supported on NT)
LP982 (FCA2408) (not
supported on NT)
1.01a2
1.01a2
4.82a16
4.82a16
LP9802 (FCA2404)
and LP9802DC
(FCA2404DC) (neither
supported on NT
Novell
5.1 SP6,
6.0 SP3
QLA 2340 (FCA2210)
1.29
6.50.z
3.0c with
SP1
N5.1 supports NCS
V1.01
NetWare
V6.0 supports NCS
v1.06,
Max: 6 nodes
Sun Solaris
2.6, 7, 81
2.6, 7, 8
JNI FCI-1063 (32-bit
PCI)
3.0.3
2.5.9-03
3.0c with
SP1
Veritas Cluster
Services v2.0 or v3.5;
Max 16 nodes
SWSA4-SB 1 Gb
32-bit SBUS
13.3.7
Sun Clusters v2.2;
Max: 16 nodes
JNI FC64-1063 (64-bit
Sbus)
2.6, 7, 8, 9
QLA2202 Sbus 1Gb
(FCA2257S)
FC 1.18.3,
4.11
firmware comes
with driver
QLA2310 Sbus 2Gb
(FCA2257P)
FC 1.18.5,
firmware comes
with driver
8 or 9 Build 2
QLA2202 cPCI 1Gb
(FCA2257C)
FC 1.18.5,
firmware comes
with driver
1. If used with 2 Gbps B-series switches, you must use the latest switch firmware (v2.2.1c, v3.1.1c, or 4.1.2b at time of publication).
6
Data Replication Manager HSG80 ACS Version 8.7P Release Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
What’s New
Table 2: Supported Switches for the HSG80
Fibre Channel Switch
DRM Supported Switch Firmware
B-Series
HP StorageWorks SAN Switch 8, 16, 8-EL, and
16-EL (1 Gb)
2.6.2 preferred
2.6.1c optional
HP StorageWorks SAN Switch 2/8, 2/16, 2/8-EL,
and 2/16-EL (2 Gb)
3.2 preferred
3.1.1c optional
HP StorageWorks SAN Switch Integrated/32 and
Integrated/64
2.6.2 preferred
2.6.1c optional
HP StorageWorks SAN Switch 2/32
4.2 preferred
4.1.2b optional
C-Series
Cisco MDS9120, MDS9140, MDS9216, MDS9506,
and MDS9509
1.2.1b
M-Series
HP StorageWorks Edge Switch 2/24
5.02.00-13
5.02.00-13
HP StorageWorks Edge Switch 2/16 and 2/32
HP StorageWorks Core Switch 2/64
4.2 preferred
4.1.2b optional
HP StorageWorks Director 2/64
HP StorageWorks Director 2/140
5.02.00-13
5.02.00-13
Data Replication Manager HSG80 ACS Version 8.7P Release Notes
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Common Platform Issues
Common Platform Issues
Performance Considerations—Adding Target Unit Back to Remote Copy Sets
Each remote copy set is forced into a full normalization when you add back the target unit
using the following command:
SET RemoteCopySetName ADD = TargetRemoteCopyName\UnitName
Example: set rcs1 add = buildngA\d1
In some cases this normalization has an impact on data replication performance and therefore
should not be performed during periods of high I/O activity at the target site. You may wish to
stagger the normalization of each remote copy set to minimize the performance impact.
Performance Considerations—Full Copy Operation
During full copy operations, host I/O performance is moderately reduced, and the length of
time required for the copy operation is longer than that for a merge operation.
Performance Considerations—Write History Log Merge
During Write History Log merge, host I/O performance is drastically reduced due to the high
priority given to the merge operation. The length of time required for the merge operation is
affected by host I/O, as new I/O is added to the end of the Write History Log, while the oldest
is pulled from the beginning of the log.
SWCC and OpenView Management Appliance Limitations
The HSG80 controller does not distinguish between commands issued from in-band command
tools (SWCC, Command Scripter, or the HP OpenView Storage Management Appliance) and
commands issued out of band through the serial port. Serial port commands should be
performed only when the customer has restricted commanding from other sources. Special
care must be taken with the Storage Management Appliance (SMA), as it periodically issues
polling commands that can interrupt serial port communications. If you will be using the serial
port on the HSG80 controller, remove the SMA from the fabric or use switch zoning to isolate
the SMA from the array in which controllers are commanded through a serial port.
Using Switch Zoning to Prevent Crashes When Using VTDPY Host Display
The HSG80 controller may crash when using the Display Host functionality in VTDPY. If
more than 21 connections are displayed (the equivalent of one page), the controller will crash
with a last fail code of 01932588 (cache data allocation parity error). HP recommends that you
use switch zoning to limit the number of connections visible to the controller. For more
information about switch zoning, refer to the HP StorageWorks Data Replication Manager
HSG80 ACS Version 8.7P Configuration Guide.
Invalid VTDPY Percentages
During the transition time between site failover and site failback, the log, merge, and copy
percentages on the original initiator displayed by VTDPY are not valid. Disregard these
percentages.
8
Data Replication Manager HSG80 ACS Version 8.7P Release Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
Common Platform Issues
Using Switch Zoning to Prevent Crashes When the 96-Connection Limit Is Exceeded
The HSG80 controller may crash if more than 96 connections exist on the fabric. HP suggests
that you use switch zoning to limit the number of connections visible to a single HSG80
controller. For more information about switch zoning, refer to the HP StorageWorks Data
Replication Manager HSG80 ACS Version 8.7P Configuration Guide.
I/O Pause During Fabric Reconfiguration
During a fabric reconfiguration, you will notice a brief pause in I/O functions on all servers
connected to the fabric. This brief cessation of read/write operations is normal. A fabric
reconfiguration can be caused by switches starting up or shutting down, and by the physical
plugging or unplugging of fiber cables.
Controller Saturation
High usage of many remote copy set and nonremote copy set LUNs has a serious impact on
the performance of the remote copy set LUNs, causing controller saturation and possibly
starving a full copy operation.
A saturated controller condition begins approximately when idle time falls to 25% or less
when viewed through VTDPY. When this occurs, you may see Aborted Command errors
through the Command Line Interface (CLI).
To prevent controller saturation:
■
Avoid placing multiple heavy-use loads on the controllers.
■
Use the VTDPY screen to monitor controller idle time percentage. Adjust load to maintain
an idle time of 25% or greater.
RAID 5 Remote Copy Set Target Drop
Under the following combined conditions, RAID 5 remote copy set targets may be dropped:
■
No write history log disk is configured, and
■
Host I/O is accessing the initiator remote copy set LUNs.
When both target controllers are shut down, a full copy operation is triggered. When the target
controllers are restarted, they will begin a 3-minute memory diagnostic.
While the memory diagnostics are running, the full copy I/O to RAID 5 target LUNs is stalled.
Therefore, after approximately 2 minutes, a timeout occurs and the target LUNs are dropped
from the remote copy set. This target drop problem occurs only on RAID 5 remote copy set
LUNs.
■
To prevent target LUN drop:
1. Set port_2_topology on both initiator controllers to offline before target controllers are
booted and powered on.
2. Wait five minutes after target controllers are restarted to allow for memory diagnostics
to complete.
3. Set port_2_topology on the initiator controllers back to fabric.
Data Replication Manager HSG80 ACS Version 8.7P Release Notes
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Common Platform Issues
■
If the target LUNs are dropped:
1. Wait five minutes to allow for the target controller memory diagnostics to complete.
2. Add the targets back into the remote copy sets.
The full copy operation begins.
Required Delay Time Before Failback
Be careful that you do not start a site failover or site failback process too soon. You must wait
a minimum of 15 minutes from the completion of a site failover process to begin a site failback
procedure. You must also wait a minimum of 15 minutes from the completion of a site failback
process to begin a site failover procedure.
Removing Targets from the Proper Controller
The target of a remote copy set should be removed by the controller to which it is online. A
problem occurs if both fabric intersite links are not functioning and you remove the target of a
remote copy set that is part of an association set with a write history log. If you try to remove
the target from the controller that the remote copy set is not online to, and then issue the CLI
command SHOW REMOTE COPY SET FULL, the target state will indicate LUN D0 is
copying 0% complete. The actual indication of the target state should be "No targets."
Example:
Name
---------------------------------------------------------------------------
RCS1 remote copy D1 AS1
Uses
Used by
Reported LUN ID: 6000-1FE1-0007-9DD0-0009-0510-3907-000E
Switches:
OPERATION_MODE = SYNCHRONOUS
ERROR_MODE
FAILOVER_MODE
= NORMAL
= MANUAL
OUTSTANDING_IOS = 20
Initiator (BUILDNGA\D1) state:
ONLINE to the other controller
Target state:
\D0
is COPYING
0% complete
Another problem occurs when you try to add the target back in. You will see the %EVL error
message: "Too many targets have been specified in this set." You cannot add a target if you are
in a normal production mode or if you are in a failed-over condition. You must first issue the
CLI command to delete the remote copy set, and then issue the CLI command to add the
remote copy set back in. Deleting and then re-adding the remote copy set will force
normalization.
If your intersite links will be down for an extended period of time after a failover, HP
recommends that you delete your associations sets and then remove your remote copy sets to
the target controller. This may require a remapping of your host to LUN connections with
some operating systems. Run the initiator controller in standalone mode until your intersite
links are re-established.
Startup of Only One Fabric at a Time
When an event occurs that causes a fabric reconfiguration (for example, a scheduled or
unscheduled outage of an intersite link, addition or removal of a switch or switch-to-switch
link, and so on), allow all of the Fibre Channel switches in that fabric to reconfigure before
you reconfigure the second fabric.
10
Data Replication Manager HSG80 ACS Version 8.7P Release Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
Common Platform Issues
Intermittent Double Normalization After a Full Failback or Failback to New
Hardware Procedure
After you have performed a full failback or failback to new hardware, a second normalization
(from the initiator to target) can occur. This double normalization happens after the point in the
failback procedure where you add the target and normalize your storage sets (from the target to
initiator).
The only effect of this extra normalization is to add the additional controller overhead of doing
a full copy—it causes no data corruption. When normalization is complete, you can proceed
with the failback and add the load at the appropriate point in the procedure.
Command Scripter Communication Loss Due to SCSI Error
If Command Scripter v1.0A has a loss of communication while a script is running, it will
cause the script to abort. You must then put the controllers in a known state by issuing the
appropriate CLI commands from the controllers. You can examine the .log files in the
$CLONE_HOME/log directory to determine which commands were executed before
communication was lost.
If the communication failure is due to a SCSI error, then the loss of connection is only
momentary. You can verify that the connection is re-established by issuing the following
command from the host:
cmdscript -f <device Name> "show this"
However, if this command continuously gives a communication failure error, a hardware
failure or configuration error is indicated. Troubleshoot the loss of connection for causes such
as broken links, failed devices, controller configuration, and so on.
Waiting for Write History Logging Disks
After clearing invalid cache and lost data, remote copy set processing will halt. When you
issue the CLI command SHOW REMOTE_COPY_SETS FULL, you may see the following
error message:
Waiting for write history logging disks to become ready.
Restart the controller to clear this condition.
Association Sets
Association sets can contain up to 12 remote copy sets. However, because all remote copy sets
within an association set are moved between controllers as a group, all remote copy sets within
an association set must be accessed by the same server.
For instance, 6 remote copy sets (one association set) could be accessed by one server and 6
remote copy sets (another association set) by the other.
Data Replication Manager HSG80 ACS Version 8.7P Release Notes
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform-Specific Issues
Platform-Specific Issues
HP HP-UX
Failure to Mount File System after Failover or Failback
If you are unable to mount a previously configured file system after a failover or failback, run
File System Check on the logical volume and retry the mount.
Example: FSCK -O full /dev/vg0#/lvol#
Configuring Host Server Remote Copy Sets
Remote copy sets (RCSs) at the target site will acquire the world wide name of their RCSs at
the initiator site when a failover occurs. HP recommends that you not configure the RCS on
the HP-UX host servers at the target site until after a failover.
HP OpenVMS
Additional Software Requirements
Remedial kits that you may require are available at:
HP Tru64 UNIX
Prevent Possible Data Corruption
If during the failover procedure you are unable to stop all applications and dismount all units
that are part of a remote copy set, you must reboot hosts prior to failback. Doing this prevents
possible data corruption caused by writing stale data from host cache to the units after
failback.
Note: Extreme care must be used when creating and managing remote copy sets on an ATM link. If
these links are overstressed (for example, an excessive number of remote copy sets created for a
given environment), unexpected behavior may result, such as loss of remote copy sets and link
failures.
Accessing Special Device Files During Fabric Failover
HP recommends that no attempt be made to access the special device files during a fabric
failover. Running any commands against the block or raw devices in /dev/disk or /dev/rdisk is
highly discouraged. In rare instances, running the FILEcommand against raw or block
devices during a fabric failover has prevented the surviving path from coming online following
failure of the original path.
12
Data Replication Manager HSG80 ACS Version 8.7P Release Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform-Specific Issues
IBM AIX
Increased LUN Support
Beginning with Secure Path Version 1.5.19.1 for the Cambex drivers, the maximum number of
LUNs supported increased from 16 to 32.
Microsoft Windows 2000
Auto Failback
The Secure Path for Windows 2000 Auto Failback feature is not currently supported in a Data
Replication Manager configuration. Disable this feature by starting Secure Path Manager, then
selecting Properties > Autofailback > Disable.
Booting Windows 2000 Servers Over the Fabric
Any of the Windows servers can be booted from a LUN on an HSG80 controller, including a
LUN that is part of a remote copy set. Instructions for configuring servers and booting
Windows 2000 are available for download from the Web at:
Two problem situations could arise when booting over the fabric:
■
If the boot LUN is online to a controller that the server cannot access, the server will be
unable to boot. This condition could occur if the link between the server and the fabric is
broken. At this stage of booting, the server cannot move the LUN between controllers. The
LUN must be manually moved to the other controller by issuing the following CLI
commands:
SET UNIT_NUMBER PREFERRED=OTHER
SET UNIT_NUMBER NORUN
SET UNIT_NUMBER RUN
■
When an intersite link with high latency (such as ATM) is used, the server may take a long
time to boot and may be slow to respond during normal operation. This is normal behavior
for the server. It is caused by the time required to replicate the boot disk across a very long
distance.
Check Status
If a target controller or switch becomes inoperative and the Windows 2000 host is rebooted,
Secure Path Manager will not report that you have lost multipath capability.
If you attempt to move a LUN to the inoperative path, a warning message appears, indicating
that you should check the Application Event Log for details. This may be an indication that
you have lost multipath capability.
Check the status of links, target switches, and target controllers.
Data Replication Manager HSG80 ACS Version 8.7P Release Notes
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform-Specific Issues
HSG80 Controller Soft Shutdown/Restart
When the SHUTDOWN THISor SHUTDOWN OTHERcommand is executed from the CLI, the
controller will shut down, forcing the LUNs to change paths. Secure Path will immediately fail
the LUNs over to the remaining path, but the original path may not be marked as failed for
several minutes.
Similarly, when the RESTART THISor RESTART OTHERcommand is executed from the
CLI, the controller will restart, forcing the LUNs to change paths. Secure Path will
immediately fail the LUNs over to the remaining path, but the original path will never be
marked as failed. The icon for the failed LUN will be marked with a yellow triangle with an
exclamation point inside. The controller will finish restarting and return to normal operation
without notification.
The following procedure can be used to check whether a system is in this state:
1. Select one of the units in Secure Path Manager.
2. Click the path marked Available in the right-hand pane, and then right-click it to bring up
the menu.
3. Select Verify Path from the menu that appears.
If the verify fails, the path is not available. The path becomes available again after the
controller is booted.
Component failures and other real failure scenarios cause paths in Secure Path to be correctly
marked as failed.
LUNs Lettered Incorrectly
When LUNs are moved between hosts (such as during a site failover or a site failback), it is
possible that the LUNs may become “out of letter order.”
To prevent the “out of letter order” status, follow the steps below:
1. Before booting the Windows 2000 host, make sure all LUNs are failed over to one HSG80
path. From the HSG80 CLI prompt, issue the following command:
Restart Other_Controller
2. Reboot the Windows 2000 host.
3. Use Disk Manager to assign the correct drive letter so that the disks now match the units
on the controller.
4. Once Windows 2000 sees the disks ordered properly, use Secure Path Manager to move
the units to the correct path.
Changing Host Connection Unit Offsets
If the UNIT_OFFSET of a connection is changed, the host must be rebooted to recognize the
change. The host will continue to operate using the offset that was previously in effect until it
is rebooted. For example, if a host connection has a unit offset of zero, it will be able to access
only units D0 through D7. If the offset is changed to 8, the host will still be able to access units
D0 through D7 until it is rebooted. After reboot, it will be able to access only units D8 through
D15.
14
Data Replication Manager HSG80 ACS Version 8.7P Release Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform-Specific Issues
Windows 2000 Plug and Play Manager Generates Numerous Pop-up Windows
Each time a LUN is dismounted ungracefully (for example a fabric failure), Windows 2000
displays a pop-up window that warns of “Unsafe removal of device.” This window can be
cleared by simply clicking OK. The window itself is harmless, but additional dismounts cause
more pop-up windows to appear. These windows can stack up on the desktop and consume
memory to the point that the system crashes. However, several hundred dismounts and
associated pop-up messages are required before a system crash is probable.
Windows Using Large LUNs While in SCSI-2 Mode
DRM supports Windows 2000 hosts accessing large LUNs above D7 without offsets via
Secure Path. However, all hosts using large LUNs on a controller in SCSI-2 mode must create
a dummy LUN 0 and give access to this LUN. HP also recommends that this phantom LUN be
set to “no write” access. Refer to the HP StorageWorks Secure Path for Windows Installation
and Reference Guide for additional information.
Association Sets
In a Windows 2000 cluster configuration, all remote copy sets within an association set must
be placed in one cluster resource group.
Microsoft Windows NT
Auto Failback
The Secure Path for Windows NT Auto Failback feature is not currently supported in a Data
Replication Manager configuration. Disable this feature by starting Secure Path Manager, and
then selecting Properties > Autofailback > Disable.
LUNs Lettered Incorrectly
When LUNs are moved between hosts (such as during a site failover or a site failback), the
LUNs may become “out of letter order.”
To prevent the “out of letter order” status, follow the steps below:
1. Before booting the Windows NT-X86 host, make sure all LUNs are failed over to one
HSG80 path. From the HSG80 CLI prompt, issue the following command:
Restart Other_Controller
2. Reboot the Windows NT-X86 host.
3. Use Disk Administrator to assign the correct drive letter so that the disks will now match
the units on the controller.
4. Once Windows NT sees the disks ordered properly, use Secure Path Manager to move the
units to the correct path.
Windows Using Large LUNs While in SCSI-2 Mode
DRM supports Windows NT hosts accessing large LUNs above D7 without offsets via Secure
Path. However, all hosts using large LUNs on a controller in SCSI-2 mode must create a
dummy LUN 0 and give access to this LUN. HP also recommends that this phantom LUN be
set to “no write” access. Refer to the HP StorageWorks Secure Path for Windows Installation
and Reference Guide for additional information.
Data Replication Manager HSG80 ACS Version 8.7P Release Notes
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform-Specific Issues
Association Sets
In a Windows NT- X86 cluster configuration, all remote copy sets within an association set
must be placed in one cluster resource group.
Novell NetWare
NetWare Cluster Services (NWCS)
NWCS v1.01 SP1 for NetWare 5.1 and NWCS v1.6 for NetWare 6 are supported at the
initiator and target sites. Stretch clusters are not supported at this time. A stretch cluster is
defined as having a NetWare Cluster using NWCS with cluster members located at both the
DRM initiator and target sites. NWCS supports both remote copy set and nonremote copy set
LUNs.
Planned Failover/Failback with NWCS
When preparing the initiator and target sites for a planned failover/failback, use caution when
removing access to the LUNs at the initiator site. Removing access to the split brain detector
(SBD) partition, as well as the cluster volumes, without first bringing down the cluster will
result in server abends. To avoid cluster members abending, issue the following command at
the system console:
CLUSTER DOWN
You can also run ULDNCS.NCFat the system console for each cluster member to unload
cluster services completely.
NetWare 6 Storage Planning Considerations
If you plan on using Novell Storage Services (NSS) logical volumes in a DRM configuration,
you should be aware that the nature of Novell's Distributed File Services (DFS) allows you to
span an NSS volume across multiple hard disk partitions. This is not desirable in a DRM
configuration. Instead, you should maintain a one-to-one relationship among LUNs, remote
copy sets, NSS partitions, NSS pools, and NSS logical volumes.
Additional Instructions for Failover/Failback
When NetWare volumes are created at the initiator site, they are inserted into the Novell
Directory Services (NDS) tree as servername_volumename (for example, SERVER1_VOL1).
After a site failover, the replicated NetWare volumes are still available and can be mounted by
any NetWare server at the target site, but the volumes will now take on the new server name
(for example, SERVER2_VOL1). In addition, they will not be automatically inserted into
NDS, and for traditional NetWare volumes only, they will not maintain the file system
permissions established at the initiator site. You MUST perform the following steps the first
time failed-over volumes are mounted at the target site:
Traditional NetWare Volumes
After failing over to the target site and mounting the NetWare volumes:
1. Type nwconfigfrom the file server console.
2. Select Directory Options.
3. Select Upgrade Mounted Volumes into the Directory, and supply an
administrator-equivalent userid and password.
16
Data Replication Manager HSG80 ACS Version 8.7P Release Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform-Specific Issues
4. Access a Windows workstation (or the file server's graphical console) and use the
ConsoleOne utility to establish the desired file system permissions for the newly inserted
volumes.
NSS Logical Volumes
After failing over to the target site and mounting the NSS logical volumes:
1. Run ConsoleOne from a Windows workstation or the file server's graphical console.
2. Select Disk Management > NSS Pools from the Tools menu.
3. Select the correct NDS Tree, NDS Context, and Server when prompted.
4. Ensure that the Media tab is highlighted and NSS Pools is displayed. Click the correct
NSS Pool from the list on the left to highlight the pool, and then click the Update NDS
button.
5. Click the Media tab and then NSS Logical Volumes.
6. Click the correct NSS Logical Volume from the list on the left to highlight the volume,
and then click the Update NDS button.
Note: You must perform steps 4 through 6 above for each NSS Pool/Volume pair you fail over from
the initiator site.
After the above procedures are accomplished, they will not have to be performed again as long
as the volumes are always mounted on the same target file server after a failover.
Upon failback to the initiator site, any new files or directories created at the target site will
need to have permissions reestablished using the ConsoleOne utility (for traditional NetWare
volumes only). When performing subsequent failovers, it is not necessary to insert the volumes
into the NDS tree—they will already be there. Simply make sure that the necessary
permissions are granted using ConsoleOne if any new files or directories have been created at
the initiator site (for traditional NetWare volumes only).
CPU Hog Abends
Auto Failback
If you experience CPU Hog Timeout server abends, you may have to adjust the CPU Hog
Timeout amount (using MONITOR.NLM under the menu parameter Server Parameters,
Miscellaneous) to a lower amount or 0 seconds (disabled).
Auto Failback is supported using Secure Path for NetWare. Failures involving the target site
(extended intersite link failures, target switch failures, target controller failures) cause Secure
Path to fail LUNs to their alternate paths. However, Auto Failback to the preferred path may
not occur after the link is restored. In these situations, use the Secure Path Manager (GUI) to
manually move LUNs back to their preferred paths. Refer to the HP StorageWorks Secure Path
for Novell Netware Installation and Reference Guide for additional details on performing this
operation.
Partitioned LUNs
Novell servers cannot access partitions if another partition on the same physical disk (LUN) is
accessed by another operating system. When this happens, the Novell server may lock up. To
prevent lockup, remove any other operating systems accessing the partitions.
Data Replication Manager HSG80 ACS Version 8.7P Release Notes
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Platform-Specific Issues
Maximum Number of Host Bus Adapters
The maximum number of host bus adapters supported by a Novell host is four. This is a
limitation of Secure Path.
Sun Solaris
Memory Requirement
Sun Solaris requires at least 512 MB RAM per CPU when running ACS v8.7P. Edit the
etc/system file to include the following line:
set lwp_default_stksize=0x8000
18
Data Replication Manager HSG80 ACS Version 8.7P Release Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
|