Hardware Reference Guide
HP Compaq t5135/t5530 Thin Clients
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Book
WARNING! Text set off in this manner indicates that failure to follow directions could result in
bodily harm or loss of life.
CAUTION Text set off in this manner indicates that failure to follow directions could result in
damage to equipment or loss of information.
NOTE Text set off in this manner provides important supplemental information.
ENWW
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
About This Book
ENWW
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of contents
2 Hardware changes
Replacing the battery ......................................................................................................................... 12
3 Specifications
4 Security provisions
5 Mounting the thin client
Non-supported mounting option ........................................................................................ 22
6 Thin client operation
ENWW
v
Download from Www.Somanuals.com. All Manuals Search And Download.
7 Electrostatic discharge
8 Shipping information
vi
ENWW
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Product features
Standard features
Thank you for purchasing an HP Compaq thin client. We hope you have years of use from our t5135 or
t5530 thin clients. Our goal is to provide you with award-winning clients that are easy to deploy and
manage with the power and reliability you expect.
HP has partnered with Altiris to manage HP Compaq thin clients. Altiris Deployment Solution is a leading-
edge tool to help with quick deployment and for ongoing management of the thin clients in your
organization. Each HP Compaq thin client is recognized by the Altiris Deployment Solution as a
supported device. As a result, you need not track license compliancy for each device. For additional
information about the Altiris Deployment Solution tool, refer to the Altiris Deployment Solution insert that
shipped with the thin client and the Deployment Solution User Guide that is available at
The next sections describe the features of the thin client. For a complete list of the hardware and software
search for a specific thin client model.
The following features are common to all HP thin clients:
no moving parts
●
●
●
●
no hard drives or diskette drives
5-minute setup time
central deployment and management using Altiris Deployment Solution
Various options are available for your thin client. For more information about available options, visit the
HP Web site at http://h30143.www3.hp.com/configure2.cfm
ENWW
Standard features
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Front panel components
Figure 1-1 Front panel components
(1)
(2)
(3)
(4)
Secure USB compartment
Power button
(5)
(6)
(7)
Line-out (headphone) audio connector
Line-in (microphone) connector
Flash activity LED
Power LED
Universal serial bus (USB) connectors (2)
* For more information, refer to the model-specific QuickSpecs at http://h18004.www1.hp.com/products/quickspecs/
Secure USB compartment ports
Figure 1-2 Secure USB compartment ports
The secure USB compartment allows you to use two USB devices in a secured location.
2
Chapter 1 Product features
ENWW
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear panel components
Figure 1-3 Rear panel components
(1)
(2)
(3)
(4)
Cable lock slot
(5)
(6)
(7)
(8)
PS/2 connectors (2)
Monitor connector
Serial connector
Power connector
Ethernet RJ-45 connector
Parallel connector
Universal serial bus (USB) connectors (4)
For more information, see the model-specific QuickSpecs at http://h18004.www1.hp.com/products/quickspecs/
ENWW
Rear panel components
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the stand
To install the stand:
1. Turn unit upside down.
2. Locate the slots on the bottom of the unit into which the tabs on the stand fit.
3. Insert the tabs into the slots (1), and then slide the stand about 1/2–inch toward the back of the
unit until it locks into place (2).
Figure 1-4 Installing the stand
Removing the stand
To remove the stand:
1. Turn unit upside down.
2. Press the tab (1), and then slide the stand about 1/2–inch toward the front of the unit and lift the
stand off the unit (2).
Figure 1-5 Removing the stand
4
Chapter 1 Product features
ENWW
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the keyboard
Figure 1-6 Keyboard features
(1)
(2)
(3)
(4)
Caps Lock key
Scroll Lock key
Num Lock key
Ctrl key
Activates/deactivates the Caps Lock feature.
Activates/deactivates the Scroll Lock feature.
Activates/deactivates the Num Lock feature.
Use in combination with another key; its function depends on the
application software you are using.
Windows Logo Key1
(5)
Opens the Start menu in Microsoft Windows. Use in combination with
(6)
(7)
Alt key
Use in combination with another key; its function depends on the
application software you are using.
Application key1
Similar to the right mouse button, opens pop-up menus in a Microsoft
Office application. May perform other functions in other software
applications.
(8)
Editing keys
Includes the following: Insert, Home, Page Up, Delete, End, and Page
Down.
Hold Ctrl and Alt while pressing Delete to restart the thin client.
1Available in select geographic regions.
ENWW
Using the keyboard
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows Logo Key
Use the Windows Logo Key in combination with other keys to perform certain functions available in
Windows operating systems.
Windows Logo Key + Tab
Windows Logo Key + e
Switch between open items.
Open My Computer.
Windows Logo Key + f
Search for a file or folder.
Search for computers.
Windows Logo Key + Ctrl + f
Windows Logo Key + m
Windows Logo Key + Shift + m
Windows Logo Key + Break
Windows Logo Key + r
Minimize all windows.
Undo minimize all.
Display the System Properties dialog box.
Open the Run dialog box.
Additional function keys
The following key combinations also work on HP Compaq t5135/t5530 thin clients:
Alt + Esc
Cycles through minimized applications.
Cycles through open applications.
Switches to the previous session.
Alt + Tab
Alt + Shift + Tab
Special mouse functions
Most software applications support the use of a mouse. The functions assigned to each mouse button
depend on the software applications you are using.
6
Chapter 1 Product features
ENWW
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial number location
Every thin client includes a unique serial number located as shown in the following illustration. Have this
number available when contacting HP customer service for assistance.
Figure 1-7 Serial number location
ENWW
Serial number location
7
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Hardware changes
General hardware installation sequence
To ensure the proper installation thin client hardware components:
1. Back up any data, if necessary.
2. If the thin client is powered on:
a. Turn the unit and any other attached devices off.
b. Disconnect the power cord from the wall outlet.
c. Disconnect any external devices or cables.
WARNING! To reduce the risk of personal injury from electrical shock and/or hot surfaces,
be sure to disconnect the power cord from the wall outlet and allow the internal system
components to cool before touching.
WARNING! To reduce the risk of electrical shock, fire, or damage to the equipment, do
not plug telecommunications or telephone connectors into the network interface controller
(NIC) receptacles.
CAUTION Static electricity can damage the electronic components of the thin client or
optional equipment. Before beginning these procedures, ensure that you are discharged of
static electricity by briefly touching a grounded metal object. See Preventing electrostatic
damage for more information.
3. Remove any hardware that you will replace.
4. Install or replace equipment. For removal and replacement procedures, see the following
sections:
❑
❑
NOTE Option kits include more detailed installation instructions.
5. Reconnect any external devices and power cords.
6. Turn on the monitor, the thin client, and any devices you want to test.
7. Load any necessary drivers.
8
Chapter 2 Hardware changes
ENWW
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Reconfigure the thin client, if necessary.
ENWW
General hardware installation sequence
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing USB devices in the secure USB compartment
The secure USB compartment allows you to install two USB devices in a secure location inside of the
thin client. Along with providing a hidden location, the secure USB compartment can be locked by the
optional security cable lock.
CAUTION The ambient temperature inside of the secure USB compartment can reach up to
55°C in worst case conditions. Make sure the specifications for any device you install in the
compartment indicate the device can tolerate a 55°C ambient environment.
NOTE In addition to following these instructions, follow the detailed instructions that accompany
the accessory you are installing.
procedures you should follow before and after installing or replacing hardware.
Removing the secure USB compartment cover
Use the following procedure to remove the secure USB compartment cover.
WARNING! Before removing the secure USB compartment cover, ensure that the thin client is
turned off and the power cord is disconnected from the electrical outlet.
To remove the secure USB compartment cover:
1. On rear of the thin client, remove the screw that secures the compartment cover to the unit (1).
2. On the front of the unit, push the compartment cover about 1/2–inch toward the back of the unit
(2).
3. Remove the cover from the unit by first lifting the rear (screw side) of the cover, and then lifting the
cover off the unit (3).
Figure 2-1 Removing the secure USB compartment cover
10 Chapter 2 Hardware changes
ENWW
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the USB device
Insert the USB device into the USB port in the secure USB compartment. See the following
▲
illustration for the location of the ports in the secure USB compartment.
Figure 2-2 Secure USB compartment port location
Replacing the secure USB compartment cover
To replace the secure compartment cover:
1. Place the cover on top of the unit so it is offset about 1/2–inch toward the rear of the unit, allowing
the tabs on the cover to align and insert into the slots on the chassis (1).
2. Slide the cover toward the front of the unit until it locks in place and the cover is flush with the front
panel of the chassis (2).
3. Replace the screw (3).
Figure 2-3 Replacing the secure compartment cover
To remove USB devices from the secure compartment, reverse the previous procedures.
ENWW
Installing USB devices in the secure USB compartment 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the battery
procedures you should follow before and after installing or replacing hardware.
To replace the battery:
1. Remove the side access panel and metal side cover
2. Remove and replace the battery
3. Replace the metal side cover and side access panel
Removing the side access panel and metal side cover
WARNING! Before removing the side access panel, ensure that the thin client is turned off and
the power cord is disconnected from the electrical outlet.
To remove the access panel:
2. Remove the two back panel screws that secure the access panel to the chassis (2).
3. Slide the access panel about 1/4–inch toward the front of the unit, and then lift the access panel
up and off the unit (3).
Figure 2-4 Removing the side access panel
To remove the metal side cover:
1. Remove the three screws that secure the metal side cover to the chassis (1).
12 Chapter 2 Hardware changes
ENWW
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Lift the metal side cover up and off the unit (2).
Figure 2-5 Removing the metal side cover
Removing and replacing the battery
To remove and replace the battery:
1. Locate the battery on the system board.
2. Pull back on the clip (1) that is holding the battery in place, and then remove the battery (2).
Figure 2-6 Removing and replacing the internal battery
3. Insert the new battery and position the clip back into place.
Replacing the metal side cover and side access panel
To replace the metal side cover:
1. Place the metal side cover on the chassis, making sure to align the screw holes in the cover with
the holes in the chassis.
ENWW
Replacing the battery 13
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Insert and tighten the three screws.
Figure 2-7 Replacing the metal side cover
To replace the access panel:
1. Place the access panel on the side of the unit, offset about 1/2–inch toward the front of the unit (1).
2. Slide the panel toward the rear of the unit until it locks into place (2).
3. Replace the two screws that secure the access panel to the chassis (3).
Figure 2-8 Replacing the side access panel
External drives
Various external USB drives are available as options for the t5135/t5530. For more information about
these drives, visit http://www.hp.com/products/thinclientsoftware, or refer to the instructions that
accompany the option.
For more information about available options, visit the HP Web site at http://h30143.www3.hp.com/
14 Chapter 2 Hardware changes
ENWW
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Specifications
Table 3-1 HP Compaq t5135/t5530 Thin Client
Dimensions
7.31 in.
7.31 in
2.06 in.
2.9 lb
18.57 cm
18.57 cm
5.24 cm
1.3 kg
Width (front to back)
Height (top to bottom)
Depth
Approximate Weight
Temperature Range (fanless design)*
Operating**
50° to 104° F
-22° to 140° F
10° to 40° C
-30° to 60° C
(max. rate of change is 10° C per hour or 18° F per hour)
Nonoperating
(max. rate of change is 20° C per hour or 36° F per hour)
*Specifications are at sea level with altitude derating of
** The operating temperature range when the thin client
1° C/300m (1.8° F/1000ft) to a maximum of 3Km (10,000ft), is attached to a flat panel using the HP Quick Release
with no direct, sustained sunlight. Upper limit may be limited is 50° to 95°F (10° to 35°C).
by the type and number of options installed.
Relative Humidity (non-condensing)
Operating
10–90%
5–95%
10–90%
5–95%
(max. wet bulb temperature is 28° C or 84.2° F)
Nonoperating
(max. wet bulb temperature is 38.7° C or 101.6° F)
Maximum Altitude (unpressurized)
Operating
10,000 ft
30,000 ft
3048 m
9144 m
(max. allowed rate of change is 457m per minute or 1500
ft per minute)
Nonoperating
(max. allowed rate of change is 457m per minute or 1500
ft per minute)
Power Supply
100–240 VAC
50–60 Hz
100–240 VAC
50–60 Hz
Operating Voltage Range
Rated Line Frequency
ENWW
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-1 HP Compaq t5135/t5530 Thin Client (continued)
Power Output (maximum)
40 W
3.3 A
40 W
3.3 A
Rated Output Current (maximum)
16 Chapter 3 Specifications
ENWW
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Security provisions
Securing the thin client
The HP Compaq t5135/t5530 thin client is designed to accept a security cable lock. This cable lock
prevents unauthorized removal of the thin client, as well as locking the secure compartment. To order
1. Locate the cable lock slot on the back panel.
2. Insert the cable lock into the slot, and then use the key to lock it.
Figure 4-1 Securing the thin client
ENWW
Securing the thin client 17
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Mounting the thin client
HP Quick Release
The HP Compaq t5135/t5530 thin client incorporates four mounting points on each side of the unit.
These mounting points follow the VESA (Video Electronics Standards Association) standard, which
provides industry-standard mounting interfaces for Flat Displays (FDs), such as flat panel monitors, flat
displays, and flat TVs. The HP Quick Release connects to the VESA-standard mounting points, allowing
you to mount the thin client in a variety of orientations.
NOTE When mounting, use the 10 mm screws supplied with the Quick Release Kit.
Figure 5-1 HP Quick Release
To order this option, visit the HP Web site at http://h30143.www3.hp.com/configure2.cfm
18 Chapter 5 Mounting the thin client
ENWW
Download from Www.Somanuals.com. All Manuals Search And Download.
To use the HP Quick Release with a VESA-configured thin client:
1. Using four 10 mm screws included in the mounting device kit, attach one side of the HP Quick
Release to the thin client as shown in the following illustration.
Figure 5-2 Connecting the HP Quick Release to the thin client
2. Using four screws included in the mounting device kit, attach the other side of the HP Quick Release
to the device to which you will mount the thin client. Make sure the release lever points upward.
Figure 5-3 Connecting the HP Quick Release to another device
ENWW
HP Quick Release 19
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Slide the side of the mounting device attached to the thin client (1) over the other side of the
mounting device (2) on the device on which you want to mount the thin client. An audible 'click'
indicates a secure connection.
Figure 5-4 Connecting the thin client
NOTE When attached, the HP Quick Release automatically locks in position. You only need to
slide the lever to one side to remove the thin client.
CAUTION To ensure proper function of the HP Quick Release and a secure connection of all
components, make sure both the release lever on one side of the mounting device and the
rounded opening on the other side face upward.
Supported mounting options
The following illustrations demonstrate some of the supported and not supported mounting options for
the mounting bracket.
You can mount a thin client between a flat panel monitor and the wall.
●
Figure 5-5 Thin client mounted with flat panel on wall
20 Chapter 5 Mounting the thin client
ENWW
Download from Www.Somanuals.com. All Manuals Search And Download.
You can mount the thin client on the back of a flat panel monitor stand.
●
Figure 5-6 Thin client mounted on back of monitor stand
You can mount the thin client on a wall.
●
Figure 5-7 Thin client mounted on wall
You can mount the thin client under a desk.
●
ENWW
HP Quick Release 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 5-8 Thin client mounted under desk
Non-supported mounting option
CAUTION Mounting a thin client in an non-supported manner could result in failure of the HP
Quick Release and damage to the thin client and/or other equipment.
Do not mount the thin client on a flat panel monitor stand, between the panel and the stand.
Figure 5-9 Unsupported mounting position - thin client between stand and monitor
22 Chapter 5 Mounting the thin client
ENWW
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Thin client operation
Routine thin client care
Use the following information to properly care for your thin client:
Never operate the thin client with the outside panel removed.
●
●
Keep the thin client away from excessive moisture, direct sunlight, and extreme heat and cold. For
information about the recommended temperature and humidity ranges for the thin client, see
Keep liquids away from the thin client and keyboard.
●
●
Turn off the thin client and wipe the exterior with a soft, damp cloth as needed. Using cleaning
products may discolor or damage the finish.
Supported orientations
HP supports the following orientations for the thin client.
CAUTION You must adhere to HP-supported orientations to ensure your thin clients function
properly.
You can place the thin client vertically using the supplied stand.
●
Figure 6-1 Vertical orientation
You can lay the thin client horizontally on its rubber feet.
●
ENWW
Routine thin client care 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 6-2 Horizontal orientation
You can lay the thin client under a monitor stand with at least one inch of clearance.
●
Figure 6-3 Under monitor stand
Non-supported orientation
HP does not support the following orientation for the thin client.
CAUTION Non-supported placement of thin clients could result in operation failure and/or
damage to the devices.
CAUTION Thin clients require proper ventilation to maintain operating temperature.
Do not put thin clients in drawers or other sealed enclosures. Thin clients require proper ventilation to
maintain operating temperatures.
24 Chapter 6 Thin client operation
ENWW
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 6-4 Do not put thin clients in drawers or other sealed enclosures
ENWW
Non-supported orientation 25
Download from Www.Somanuals.com. All Manuals Search And Download.
7 Electrostatic discharge
A discharge of static electricity from a finger or other conductor may damage system boards or other
static-sensitive devices. This type of damage may reduce the life expectancy of the device.
Preventing electrostatic damage
To prevent electrostatic damage, observe the following precautions:
Avoid hand contact by transporting and storing products in static-safe containers.
Keep electrostatic-sensitive parts in their containers until they arrive at static-free workstations.
Place parts on a grounded surface before removing them from their containers.
Avoid touching pins, leads, or circuitry.
●
●
●
●
●
Always be properly grounded when touching a static-sensitive component or assembly.
26 Chapter 7 Electrostatic discharge
ENWW
Download from Www.Somanuals.com. All Manuals Search And Download.
Grounding methods
There are several methods for grounding. Use one or more of the following methods when handling or
installing electrostatic-sensitive parts:
Use a wrist strap connected by a ground cord to a grounded Thin Client chassis. Wrist straps are
flexible straps with a minimum of 1 megohm +/- 10 percent resistance in the ground cords. To
provide proper grounding, wear the strap snug against the skin.
●
●
Use heelstraps, toestraps, or bootstraps at standing workstations. Wear the straps on both feet
when standing on conductive floors or dissipating floor mats.
Use conductive field service tools.
●
●
Use a portable field service kit with a folding static-dissipating work mat.
If you do not have any of the suggested equipment for proper grounding, contact an HP authorized
dealer, reseller, or service provider.
NOTE For more information about static electricity, contact an HP authorized dealer, reseller,
or service provider.
ENWW
Grounding methods 27
Download from Www.Somanuals.com. All Manuals Search And Download.
8 Shipping information
Shipping preparation
Follow these suggestions when preparing to ship the thin client:
1. Turn off the thin client and external devices.
2. Disconnect the power cord from the electrical outlet, then from the thin client.
3. Disconnect the system components and external devices from their power sources, then from the
thin client.
4. Pack the system components and external devices in their original packing boxes or similar
packaging with sufficient packing material to protect them.
Important service repair information
In all cases, remove and safeguard all external options before returning the thin client to HP for repair
or exchange.
In countries that support customer mail-in repair by returning the same unit to the customer, HP makes
every effort to return the repaired unit with the same internal memory and flash modules that were sent.
In countries that do not support customer mail-in repair by returning the same unit to the customer, all
internal options should be removed and safeguarded in addition to the external options. The thin client
should be restored to the original configuration before returning it to HP for repair.
28 Chapter 8 Shipping information
ENWW
Download from Www.Somanuals.com. All Manuals Search And Download.
|