16
HP Vectra VLi 8 PC
Models and Accessories
Product
Number
Hard
Drive
Video
Controller
St d.
RAM
Multi-media
LAN
OS1
Vectra VLi 8 PC
Models with Intel Pentium II Processor,
100MHz System Bus Speed, and 512 KB Level 2 Cache Memory
HP Vectra VLi 8 PC 400/100 (CPL: 03/99
)
D7941A/T 6.4 GB
Integrated
Matrox
MGA-G200 AGP 100 MHz
(8 MB SGRAM
64 MB
SDRAM
no
no
W95
NT
IDE
D7942A/T
3COM
3C905B- 4.0
TX
WS
fitted, not
D7943A/T 8.4 GB
32 ✕ Max IDE
no
W95
upgradeable)
IDE
CD-ROM
D7944T
6.4 GB
IDE
no
NT
4.0
WS
D7945A/T
32 ✕ Max IDE
CD-ROM
16
D8794A
no
DOS
Vectra VLi 8 PC
Models with Intel Pentium III Processor,
100 MHz System Bus Speed, and 512 KB Level 2 Cache Memory
HP Vectra VLi 8 PC 450/100 (CPL: 03/99
)
D7951A/T 6.4 GB
Integrated
Matrox
MGA-G200 AGP 100 MHz
(8 MB SGRAM
64 MB
SDRAM
no
no
W95
NT
IDE
D7952A/T
3COM
3C905B- 4.0
TX
WS
fitted, not
D7953A/T 8.4 GB
32 ✕ Max IDE
no
W95
upgradeable)
IDE
CD-ROM
D7954T
6.4 GB
IDE
no
NT
4.0
WS
D7955A/T
32 ✕ Max IDE
CD-ROM
Medium-Profile
Download from Www.Somanuals.com. All Manuals Search And Download.
Desktop Vectras
HP Vectra VLi 8 PC 16-1
HP Vectra VLi 8 PC
Input Devices
HP Standard Keyboard
HP Scrolling Mouse
C4735A
C4736A
Video Displays
All current HP Displays (see the HP Vectra Accessory Service Handbook)
Mass Storage
4.3-GB IDE hard disk
D8371A
D8372A
D8373A
D6650A
D6651A
6.4-GB IDE hard disk
8.4-GB IDE hard disk
HP 100 MB Atapi II Iomega ZIP drive
HP 100 MB Atapi II Iomega ZIP drive (pack of 10)
Multimedia
32✕ Max IDE CD-ROM drive (pack of 10)
32✕ Max IDE CD-ROM drive
D6656A
D4384A
D5183A
Multimedia sound accessory kit (16-bit audio board, cables, and software) -
pack of 10
Multimedia sound accessory kit (32✕ Max CD-ROM drive, 16-bit audio
D6657A
board, headphones, cables, and software)
16
Data Communications and LAN Adapter Boards
HP 56K V90 PCI Fax Modem
D7808A
D7504A
D7505A
D7506A
D7507A
HP 10/100 3Com 3C905B-TX, 10/100BT Ethernet card
HP 10/100 3Com 3C905B-TX, 10/100BT Ethernet card (pack of 10)
HP 10/100 Intel PRO/100+, 10/100BT Management adapter
HP 10/100 Intel PRO/100+, 10/100BT Management adapter (pack of 10)
Security
HP Master Pass Key System Kit
HP Master Pass Key
D6655A
D6658A
D6659A
HP Locks for Master Pass Key System (pack of 50)
Medium-Profile
Desktop Vectras
HP Vectra VLi 8 PC 16-3
Download from Www.Somanuals.com. All Manuals Search And Download.
HP Vectra VLi 8 PC
System Board, BIOS, and Memory
System Board
Switches: See the
table on the next page.
16
Main Memory:
Processor: Pentium II
or Pentium III SECC2
package with integrated
heatsink and level-2
cache memory.
Two DIMM sockets which support
up to a maximum of 512 MB.
Install 32 MB, 64 MB, 128 MB or
256 MB 100 MHz SDRAM modules.
Medium-Profile
Download from Www.Somanuals.com. All Manuals Search And Download.
16-4 HP Vectra VLi 8 PC
Desktop Vectras
HP Vectra VLi 8 PC
System Board Switches
Switch
Function
RESERVED — Do Not Use
Default
Off
1
2
—
On
Crash recovery mode: forces booting in the BIOS boot
block area
Off
On
Off
On
Normal operation
Normal operation ( keyboard space-bar power-on
enabled)
3
Off
On
Off
On
Off
—
Disables keyboard power- on
Clears User and Administrator passwords
Normal operation
4
5
Off
Off
Clears CMOS (to reload the Setup program defaults)
Normal operation
6-9
10
Processor frequency, see the following table
RESERVED — Do Not Use
—
—
Off
System Frequency1
Switch
6
7
8
9
Bus 100 MHz Bus 66 MHz
350 MHz2
400 MHz
450 MHz
500 MHz
Reserved
Reserved
Reserved
2332 MHz
2662 MHz
3002 MHz
3332 MHz
3662 MHz
4002 MHz
4332 MHz
Off
On
Off
On
Off
On
Off
On
Off
Off
Off
Off
On
On
Off
On
On
Off
Off
On
On
On
On
On
On
On
Off
Off
16
1.
2.
System and processor frequency is automatically determined by the type of processor.
These options are not yet available in any model of the HP Vectra VLi 8 at the time of
printing. This information is provided for completeness only.
BIOS History
For the latest BIOS, the flasher utility program, and the BIOS history refer to the
HP World Wide Web site.
Medium-Profile
Download from Www.Somanuals.com. All Manuals Search And Download.
Desktop Vectras
HP Vectra VLi 8 PC 16-5
HP Vectra VLi 8 PC
Part Numbers
a
k
o
g
j
h
f
n
i
m
l
d
b
c
e
1
16
8
6
2
5
10
9
3
7
12
11
4
Medium-Profile
Download from Www.Somanuals.com. All Manuals Search And Download.
16-6 HP Vectra VLi 8 PC
Desktop Vectras
HP Vectra VLi 8 PC
Parts List for HP Vectra VLi 8 PC
Item
Description
Repl.
Exchange
Part Number
Part Number
1
Box assembly:
5064-9152
—
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
Cover assembly
Bezel assembly
Status panel assembly
Blank filler (5.25 inch)
Blank filler (3.5 inch)
CD frame rail
I/O blank panel
I/O locker
AGP blank panel
HDD, FDD and CD-ROM cable kit
Master key lock
Power supply
Fan assembly
Rear bezel
Floppy disk drive (bezel-less)
Airflow guide
5064-7470
5064-7471
5064-9129
5042-3073
5042-3086
5002-6213
5002-3841
5002-4795
5002-6211
5064-9135
5064-2645
0950-3472
5064-9149
5064-9127
D2035-60391
tbd
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
not
shown
2
3
4
5
Battery type CR2032
CD-ROM to audio connector cable
Headphones
1420-0356
5182-1857
5182-3552
—
—
—
IDE hard disk drive 1
16
6.4 GB
8.4 GB
13.5 GB
—
—
—
D8372-69001
D8373-69001
D8435-69001
6
7
32 ✕ Max IDE CD-ROM drive
Enhanced mouse with scroll/zoom wheel
Standard keyboard
—
D4385-69001
C4736-60101
C4735-603xx2
C4732-60324
C4734-605xx2
5064-7455
—
—
—
—
—
Standard keyboard (Japan)
Multimedia keyboard
8
Backplane board
9
System board
See PC’s system board parts list
10
or
11
12
3Com 3C905B-TX LAN board
Intel PRO/100+ LAN board
3COM Wake on LAN Cable
Mini NLX board extractor
5064-6787
5064-7434
5183-2769
5064-9114
—
—
—
—
1.
2.
For optional disk drive information, see the Accessory Service Handbook.
Where “xx” is the code for your national keyboard (see the Accessory Service Handbook).
Medium-Profile
Download from Www.Somanuals.com. All Manuals Search And Download.
Desktop Vectras
HP Vectra VLi 8 PC 16-7
HP Vectra VLi 8 PC
System Board Parts List for HP Vectra VLi 8 PC
Description
Repl.
Exchange
Part Number
Part Number
System board:
Vectra VLi 8 system board with Matrox
MGA-G200 video controller and audio
subsystem
—
D4066-69001
Processors ( SECC2 package) :
Intel Pentium II 400/100 512KB L2 cache
Intel Pentium III 450/100 512KB L2 cache
Intel Pentium III 500/100 512KB L2 cache
Main memory modules:
—
—
—
D7645-69001
D7946-69001
D7957-69001
1 ✕ 64-MB, 100 MHz noon-ECC SDRAM
D6502-63001
—
Manuals and Documentation for HP Vectra VLi 8 PC
User’s Guide Manual Kit
D7940A
1
Troubleshooting and Upgrade Guide
no number
no number1
Technical Reference Manual: hardware and BIOS
1.
Electronic file available on HP’s Web site.
Notes:
16
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
Medium-Profile
Download from Www.Somanuals.com. All Manuals Search And Download.
16-8 HP Vectra VLi 8 PC
Desktop Vectras
2 How to Install and Replace Components In Your Desktop PC
Removing and Replacing the Cover
Removing and Replacing the Cover
Removing the Cover
1 Switch off the monitor and PC, disconnect all power cords and any
telecommunication cables.
2 If necessary, unlock the cover (with the key) at the rear of the PC.
3 Open the rear catches ➊ and remove the cover ➋.
➋
➊
➊
4 Remove the front panel.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Removing and Replacing the Cover
Replacing the Cover
1 Ensure that all internal cables are properly connected and safely
routed.
2 Replace the front panel.
3 Lower the cover and slide it into position.
4 If required, lock the cover (with the key) at the rear of the PC.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
The Label Inside Your PC
The Label Inside Your PC
Inside, your PC contains a label that can be used as a simplified guide
to help you install accessories and replace components.
Shows how to remove
Shows how to
remove the hard
disk drive
the system board
(step 1 does not apply to
your PC model)
Shows how to add an
accessory board
Shows how to remove
the floppy drive
Shows how to remove
the front drive bay
53
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Upgrading the Main Memory
Upgrading the Main Memory
NOTE
Use only HP memory modules provided for your PC model. The use of
other memory modules is not supported. For information about
supported HP accessories, connect to the web site
You can install up to a total of 512 MB (two 256 MB modules). Main
memory is available in 100 MHz modules of 32 MB, 64 MB, 128 or
256 MB. (Although the 256 MB memory modules are ECC, the ECC
feature is not used by this PC.)
Location of Main Memory
(modules can be installed in
either slot)
1 Remove the PC’s cover (described in this chapter).
2 Line up the two side notches correctly and insert the new memory
module. (You can use either slot.)
3 Replace the cover (described in this chapter).
54
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Upgrading and Installing Mass Storage Devices
Upgrading and Installing Mass Storage Devices
Drive Connectors
Internal drives, such as hard disk drives, DVD drives, and CD-ROM
drives, must be connected to data and power cables. When replacing
these drives, ensure you use the correct data and power connectors.
(you can use
either connector)
Master (boot) hard disk drive
2nd hard disk drive
CD-ROM, DVD or Zip drive
Floppy drive
Power Connectors
Number
Use for
Hard disk drives, DVD drives,
CD-ROM drives, Zip drives
5
(3 devices max.)
Floppy disk drive
1
55
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Upgrading and Installing Mass Storage Devices
Which Data Connectors There are three data cables inside your PC. Two of these are for IDE
devices.
to Use
•
An Enhanced Ultra ATA IDE (Integrated Drive Electronics) hard
disk drive cable.
For optimum performance, use this cable to connect the Ultra ATA
IDE hard disk drive.
•
•
A second IDE drive cable that supports two IDE devices. If you
install a CD-ROM drive, a DVD drive or a Zip drive, connect it to this
cable.
The third cable is non-IDE and has one connector for a floppy drive.
Up to three IDE devices can be connected to the system board using
the IDE data cables.
Before Installing an IDE Refer to the drive’s installation guide to see if you must set jumpers or if
there is a special installation procedure to follow.
Hard Disk
56
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Upgrading and Installing Mass Storage Devices
Upgrading the Hard Disk Drive
CAUTION
Handle the hard disk drive with care. Avoid shocks and violent
movement as this can cause damage to the hard disk drive’s internal
components.
Make sure that you back up your files before you install a hard disk
drive. Refer to your operating system documentation for information on
how to do this.
You can replace your PC’s hard disk drive with a larger one. To do this:
1 Remove the computer’s cover (described in this chapter).
2 Remove the drive’s connectors.
3 Remove the retaining screw ➊ and slide out the drive tray ➋.
➋
➊
4 Loosen the tray’s four screws and remove the old hard drive.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Upgrading and Installing Mass Storage Devices
5 Align the new hard drive in the tray (with the correct orientation)
and tighten the screws.
6 Replace the drive tray ➊ and retaining screw ➋.
➊
➋
7 Attach the data and power connectors.
8 Replace the cover (described in this chapter).
9 Verify the new configuration by checking the HP Summary Screen.
To access the HP Summary Screen, press Escwhen the Vectra logo
appears during startup.
NOTE
Ensure that you have installed all the required operating system and HP
drivers on the newly installed drive. To reinstall operating system and
HP drivers, use the Diagnostics & Recovery CD-ROM provided with
the PC. In addition, you can find the most up-to-date versions of HP
58
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Upgrading and Installing Mass Storage Devices
Installing a Second Hard Disk Drive
CAUTION
Handle the hard disk drive with care. Avoid shocks and violent
movement as this can cause damage to the hard disk drive’s internal
components.
Make sure that you back up your files before you install a hard disk
drive. Refer to your operating system documentation for information on
how to do this.
You can install a second hard disk drive in the lower front shelf of your
desktop PC.
1 Remove the computer’s cover (described in this chapter).
2 If there is already a drive installed in the front bay, remove its power
and data connectors (so that you can remove the drive bay).
3 Pull out the sliding latch ➊ and remove the drive bay ➋.
➊
➋
4 Align the new device in the bay (with the correct orientation) and
secure it with the screws provided.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Upgrading and Installing Mass Storage Devices
5 Slide the drive bay back into the PC (ensuring the bottom catches
engage properly) and replace the sliding latch.
➋
➊
6 Attach all data and power connectors.
7 Replace the cover (described in this chapter).
8 Verify the new configuration by checking the HP Summary Screen.
To access the HP Summary Screen, press Escwhen the Vectra logo
appears during startup.
NOTE
Ensure that you have installed all the required operating system and HP
drivers on the newly installed drive. To reinstall operating system and
HP drivers, use the Diagnostics & Recovery CD-ROM provided with
the PC. In addition, you can find the most up-to-date versions of HP
60
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Upgrading and Installing Mass Storage Devices
Installing Removable Media Devices
The PC has an integrated Enhanced IDE controller which supports up
to four IDE devices. Removable media IDE devices, such as CD-ROM
drives, DVD drives, tape drives and Zip drives, require front access.
You can install a removable media IDE drive in an empty front shelf.
Refer to the drive’s manual to see if you must set jumpers or if there is
a special installation procedure to follow.
1 Remove the computer’s cover (described in this chapter).
2 If there is already a drive installed in the front bay, remove its power
and data connectors (so that you can remove the drive bay).
3 Pull out the sliding latch ➊ and remove the drive bay ➋.
➊
➋
4 Align the new device in the bay (with the correct orientation) and
secure it with the screws provided.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Upgrading and Installing Mass Storage Devices
5 Slide the drive bay back into the PC (ensuring the bottom catches
engage properly) and replace the sliding latch.
➋
➊
6 Attach all data and power connectors. If you are installing a CD-ROM
or DVD drive, connect the audio cable too.
Audio
Connector
(optional)
7 Replace the cover (described in this chapter).
8 Verify the new configuration by checking the HP Summary Screen.
To access the HP Summary Screen, press Escwhen the Vectra logo
appears during startup.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Upgrading and Installing Mass Storage Devices
Configuring an IDE Device After Installation
After installing any device, you will need to verify that your PC has
correctly identified the new configuration, by viewing the HP Summary
Screen. If the configuration is not correct, run the Setup program to
configure the device. To enter the Setup program, press F2during
startup.
IDE drives are automatically detected by the Setup program. However,
a newly installed device may require that you install an appropriate
device driver. Refer to your operating system documentation for
details. You can obtain the latest drivers from HP’s Web site at:
63
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Replacing the Floppy Drive
Replacing the Floppy Drive
1 Remove the computer’s cover (described in this chapter).
2 Remove the drive’s connectors.
3 Lift the latch ➊ and slide out the floppy drive tray ➋.
➊
➋
4 Remove the tray’s screws and remove the old floppy drive.
5 Align the new floppy drive in the tray (with the correct orientation)
and replace the screws.
6 Slide the floppy drive tray back into the PC.
7 Attach the data and power connectors.
8 Replace the cover (described in this chapter).
64
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Installing Accessory Boards
Installing Accessory Boards
Accessory Board Slots
The PC has four accessory board slots.
NOTE
Use only XT format ISA accessory boards (width less than 10.4 cm or
4.09 inches).
Accessory Board Connectors
PCI 2
PCI 3
PCI 4
Physical Slot 1
Physical Slot 2
Physical Slot 3 (Combo)
Physical Slot 4
ISA 1
ISA 2
{
•
Physical slot 1 (the top slot) can be used for a full-length 32-bit PCI
board.
•
•
Physical slot 2 can be used for a full-length 32-bit PCI board.
Physical slot 3 is a combo slot and can be used either for a full-length
32-bit PCI or a full-length XT format 16-bit ISA board.
•
Physical slot 4 (the bottom slot) can be used for a full-length XT
format 16-bit ISA board.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Installing Accessory Boards
Installing an Accessory Board
NOTE
Use only XT format ISA accessory boards (width less than 10.4 cm or
4.09 inches).
1 Remove the computer’s cover (described in this chapter).
2 Remove the retaining bracket.
3 If the selected accessory board slot is located behind the processor,
you may need to slide out the system board to allow access (refer to
see “Replacing the System Board” on page 72 for information on how
to do this).
4 Remove the slot cover.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Installing Accessory Boards
5 Aligning the board carefully, slide it into position and press it firmly
into the slot.
6 If you slid out the system board to allow access to a lower slot,
replace it.
7 Replace the retaining bracket.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Installing Accessory Boards
8 The accessory board may need a special connection, such as:
•
•
WOL (Wake on LAN) connector to the Network board.
CD-ROM drive to the sound board (if you no longer want to use
the integrated audio).
Integrated Audio Connector
If you install an add-on sound
board, remove the cable in this
connector and insert it into the
sound board’s connector.
WOL Connector
For more information, refer to the documentation that came with
the accessory board. The necessary cables are usually provided with
the accessory board.
NOTE
If you install a network board and connect it to the WOL connector, you
must enable the Suspend Wake-Up/Integrated Networkand/or
Integrated Networkfields in the Powermenu of the PC’s Setup
program. This only applies if the network board supports these modes.
To enter the Setup program, press F2 during startup.
If you install an add-on sound board (and you no longer want to use the
integrated audio), you must set the Integrated Audio Interfacein
the Advancedmenu of the Setup program to Disabled.
9 Replace the cover (described in this chapter).
68
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Installing Accessory Boards
Configuring Accessory Boards with Plug and Play
Plug and Play is an industry standard for automatically configuring
your PC's hardware resources and the accessory boards installed in it.
Your PC has configurable support for Plug and Play in the BIOS.
All PCI accessory boards are Plug and Play, although not all ISA boards
are. Check the accessory board’s documentation if you are unsure.
When you start your PC after installing an accessory board, the Plug
and Play BIOS automatically detects which hardware resources (IRQs,
DMAs, memory ranges, and I/O addresses) are used by PC components
(such as the keyboard, the communications ports, network adapters,
and accessory boards).
Windows 95 and
Windows 98
Operating systems that support Plug and Play, such as Windows 95 and
Windows 98, will automatically detect a newly installed Plug and Play
accessory board and install the driver for this device, if the driver is
available.
Windows NT 4.0
For operating systems that do not support Plug and Play, such as
Windows NT 4.0, refer to the operating system documentation for
information about installing accessory boards.
In Windows NT 4.0, click the Start button then click Help. You can
use the contents or index to find information about installing devices.
Windows NT 4.0 helps you through the installation of devices such as
modems and sound boards.
NOTE
After installing a new device in Windows NT 4.0, you must re-install the
Microsoft Service Pack to update the operating system for your PC.
To do this, click the Start button then select Programs – Windows
NT Update.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Installing Accessory Boards
Configuring non-Plug and Play ISA Accessory Boards
If you install an ISA accessory board that is not Plug and Play, you will
need to configure the board before your PC can use it. For instructions
about configuring the board, refer to the documentation that came
with the board.
For guidelines on available IRQs and I/O addresses in your PC, refer to
page 119. Some operating systems, such as Windows 95, can display
the IRQs and I/O addresses currently used by your PC. Refer to the
operating system documentation for more information.
Refer to the documentation supplied with the operating system for
details on your operating system’s capabilities and restrictions
concerning non-Plug and Play accessory boards.
Resetting the PC’s
Configuration Data
If your PC is having difficulty recognizing the ISA board, try resetting
the PC’s data configuration. This will clear any old configuration data
that is no longer used. To do this, enter the PC’s Setup program, set the
Reset Configuration Data parameter to Yes, and restart the PC.
To enter the Setup program, press F2during startup.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Replacing the Processor
Replacing the Processor
1 Remove the computer’s cover (described in this chapter).
2 Remove the old processor.
3 Install the new processor and clip it into place.
4 If the new processor is a different speed, ensure that the system
board switches are correctly set for your processor speed. (The
correct switch settings are indicated on the system board.)
5 Replace the cover (described in this chapter).
6 Ensure that the latest version of BIOS is installed on your PC. To
learn which version of BIOS is currently installed on your PC, press
ESCduring startup. To get the latest BIOS version for your PC,
71
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Replacing the System Board
Replacing the System Board
1 Remove the computer’s cover (described in this chapter).
2 Remove the lower bracket.
3 Remove the main memory and processor from the old system board
(described in this chapter).
4 Remove the old system board.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Replacing the System Board
5 First ensure the lever is open, then carefully slide in the new system
board, aligning the rails and the rear connector bracket correctly.
6 Pushing on the lever and on the system board edge, slide the system
board firmly into place. Ensure the connectors are well aligned and
fully engaged.
7 Replace the main memory and processor in the new system board
(described in this chapter).
8 Replace the lower bracket.
9 Replace the cover (described in this chapter).
73
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Replacing the Power Supply
Replacing the Power Supply
WARNING
To avoid electric shock, do not open the power supply. There are no user-
serviceable parts inside.
1 Remove the computer’s cover (described in this chapter).
2 Remove all internal power supply connectors.
Hard drive(s)
Main power
(located on backplane near
power supply)
DVD/CD-ROM
drive(s)
Floppy drive
3 Remove the hard drive tray (described in this chapter).
4 Remove the four screws securing the power supply.
5 Slide the old power supply forward and remove it.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Replacing the Power Supply
6 Insert the new power supply (lining up the metal catches).
7 Replace the four screws to secure the power supply.
8 Re-install the hard drive tray (described in this chapter).
9 Reconnect all internal power supply connectors.
10 Replace the cover (described in this chapter).
11 Select the correct voltage setting for your country.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Changing the Battery
Changing the Battery
WARNING
There is a danger of explosion if the battery is incorrectly installed. For
your safety, never attempt to recharge, disassemble, or burn the old
battery. Replace the battery only with the same or equivalent type
recommended by the manufacturer. The battery in this PC is a lithium
battery which does not contain heavy metals, nevertheless, in order to
protect the environment, do not dispose of batteries in household
waste. Please return used batteries to the shop from which you bought
them, or to the dealer from which you purchased your PC, or to HP, so
that they can either be recycled or disposed of in an environmentally
sound way. Returned used batteries will be accepted free of charge.
You should order replacement battery HP 1420-0356 from your local
Sales and Service office, or a “CR2032 type” battery, which is available
from most local stores.
After removing the computer’s cover:
1 Remove the old battery by pressing the retaining clip with a
screwdriver and lifting the battery clear of the battery holder.
2 Place the new battery in the battery holder, with the “+“ sign on top,
and ensure it is properly seated.
After installing a replacement battery, replace the computer’s cover
and run the Setup program to reconfigure the computer. You enter
Setup by pressing F2at startup.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Installing a Security Cable
Installing a Security Cable
You can secure the PC to your desk, or any other fixed object, using a
KensingtonTM security cable. Using a security cable will also lock the
cover onto the PC.
The PC has a slot at the rear for securing the cable.
1 Insert the lock into the slot located at the rear of the PC.
2 Turn the key to lock the cable to the PC.
3 Remove the key and store it in a safe place.
NOTE
The KensingtonTM security cable is not an HP accessory. It cannot be
ordered from HP. Contact your reseller for more information.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
2 How to Install and Replace Components In Your Desktop PC
Installing a Security Cable
78
Download from Www.Somanuals.com. All Manuals Search And Download.
|