15" Liquid Crystal Display
Television
User's Manual
MAK-000002
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
2
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Regulatory Information
FCC Compliance Statement1
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Additional Information
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
•
•
•
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected
•
Consult the dealer or an experienced radio/TV technician for help
Warning: You are cautioned that changes or modifications not
expressly approved by the party responsible for compliance could void
your authority to operate the equipment.
1. applies only to products purchased in the United States of America
3
Download from Www.Somanuals.com. All Manuals Search And Download.
DOC Compliance Notice1
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the Radio Interference
Regulations of the Canadian Department of Communications.This
device complies with Canada ICES-003 Class B.
CE Conformity Statement2
This device complies with the requirements set out in the Council
Directive on the approximation of the Laws of the Member States
relating to Electromagnetic Compatibility (89/336/EEC) and the
Amendment Directive (92/31/EEC), Low-Voltage Directive (73/23/EEC)
and the Amendment Directive (93/68/EEC).
1. applies only to products purchased in Canada
2. applies only to products purchased in the European Union
4
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Description of Warning Symbols
Before You Proceed
1. Read all Safety Notices in Section 2 of this manual and
instructions in the User’s Manual carefully before either plugging
in or turning the TV on.
2. Keep this User’s Manual in a safe place for future reference.
Keep the box and packaging in case the TV needs to be shipped
in the future.
3. Follow the TV and warning label instructions.
4. Any uses, operations, changes, alterations or modifications of
the TV that do not follow the instructions in this manual will void
this TV’s warranty.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING
CAUTION
This symbol is used to alert
users to pay attention to
important descriptions
regarding usage, maintenance
(repair), and additional
important information related
to this TV.
This symbol is used to alert
users to the risk of electric
shocks due to dangerous and
uninsulated components.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Safety Notices
Electric Power Notice
Electric power may cause personal injury and mechanical damage if
misused. Although safety has been taken into consideration during the
design and production of this TV, electric shock or fire can result if the
TV is misused. To prevent potential danger, read and follow the
instructions and warnings contained in this manual when setting up,
operating or cleaning the TV. In addition, please read all “Safety
Notices” contained in this manual carefully before using the TV.
Power Supply Safety Notes
1. To avoid electric shocks, do not use an extended power cord or
an outlet that does not match this TV's plug or leaves the plug
exposed.
2. This TV has a 3-pin grounded plug. The third pin connects to
ground; do not remove it or alter it in anyway.
3. If the power cord or plug is damaged or worn, unplug it
immediately and contact an authorized service technician for
maintenance.
4. To avoid fire or electric shocks, do not overload electric power
outlets.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Safety Notes
Antenna
We suggest that you use an outdoor antenna to get the best signal
possible unless you have cable TV or a centralized indoor antenna
system. You may, however, use an antenna indoors if it is placed in a
location free from interference.
Location
Avoid prolonged exposure to sunlight or other strong sources of heat.
Leave sufficient distance between the TV and the wall to provide
enough space for the emission of heat.
WARNING
To reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture.
Apparatus shall not be exposed to dripping or splashing and no
objects filled with liquids, such as vases, shall be placed on the
apparatus.
Power
To avoid danger of fires or electric shock, only use those adapters
listed below, which are compatible with this TV.
•
•
EDAC POWER ELECTRONICS CO., LTD.: EA1050A-120
LI SHIN INTERNATIONAL ENTERPRISE CORP.: 0218B1260
7
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
1
2
3
4
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
5
6
7
8
9
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install
in accordance with manufacturer’s
instructions.
Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding-type plug has two blades
and a third grounding prong. The wide blade
or the third prong are provided for your
safety. If the provided plug does not fit into
your outlet, consult an electrician for
replacement of the obsolete outlet.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
10 Protect the power cord from being walked on
or pinched, particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
11 Only use attachments/accessories specified
by the manufacturer.
12 Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or
sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13 Unplug this apparatus during lightning
storms or when unused for long periods of
time.
14 Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is
damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.
These servicing instructions are for use by
qualified service personnel only.To reduce
the risk of electric shock, do not perform any
servicing other than that contained in the
operating instructions unless you are
qualified to do so.
CAUTION
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Personal Safety
To avoid overloading the power supply, never
plug too many electrical devices into an outlet,
power strip, or extension cable.
Dangerous high-voltage electric power
components are located inside the TV. To avoid
electric shock, do not disassemble the TV in any
way.
Do not place or drop metals, small objects, or
flammable materials into the vent of the TV.
If the TV is dropped, falls down, or is otherwise
damaged, unplug the power cord immediately
and contact an authorized service technician.
If any fluid is sprayed or dropped into the TV,
contact an authorized service technician.
The screen of the TV is made of glass. Avoid
hitting or scraping it. If the screen is broken, do
not touch the broken glass.
Do not allow children to use the TV unattended.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Do not place the TV in locations where there is
excessive steam or dust.
Avoid blocking the TV's vents, do not place the
TV on a bed, sofa, carpet, or in a sealed cabinet.
Install the outdoor antenna (not included) away
from power transmission lines to avoid possible
danger.
Unplug the power cord and antenna connector
when there is a storm or when the TV is not in
use for long periods to avoid electric shock from
lightning.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
This TV is designed for home power sources as
labeled on the casing. Avoid using any other
power accessories to avoid electric shock or
other damage.
V
The plug can be inserted into an outlet in only
one direction as shown to the left. Do not alter
the plug. Contact an authorized service
technician if you cannot plug it in correctly.
If there is any problem that cannot be resolved
according to the instructions given in this
manual, contact an authorized service technician
immediately. Do not attempt any methods not
covered in this manual.
Maintenance
Do not attempt to repair the TV by yourself.
Contact an authorized service technician. Ask
the service technician to complete a safety
inspection before switching the power on after
completing any maintenance.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Preface
Thank you for purchasing a Hannspree Liquid Crystal Display Television
(LCD TV). Your new TV will allow you to enjoy superior audio and video
while enriching your lifestyle with advanced technology.
Please carefully read this manual in its entirety before setting up, using
or operating your TV. To ensure the safe and correct installation and
operations of the TV, it is important that the safety and operation
instructions in this manual are followed.
This instruction manual is designed to assist you in setting up and using
the TV. The information in this manual has been carefully checked for
accuracy; however, no guarantee is given to the correctness of the
contents. The information in this manual is subject to change without
notice.
To the extent allowed by applicable law, Hannspree California Inc.
(“Hannspree”) shall not be liable for direct, indirect, special, exemplary,
incidental or consequential damages arising from any defect or
omission in this manual, even if advised of the possibility of such
damages in advance.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Copyright
© Copyright 2004 Hannspree California Inc.
All rights reserved. This manual is protected by copyright and
distributed under licenses restricting its use, copying and distribution.
No part of this manual may be reproduced in any form by any means
without the prior written authorization of Hannspree. The TV described
in this manual may include copyrighted software of Hannspree (or other
third parties). Hannspree (or other third parties) preserves the exclusive
rights for copyrighted software, such as the right to distribute or
reproduce the copyrighted software. Accordingly, and to the extent
allowed by applicable law, any copyrighted software contained in the
product described herein shall not be distributed, modified, reverse
engineered, or reproduced in any manner without the prior written
authorization of Hannspree (or of other third parties).
The Hannspree logos presented herein are trademarks of Hannspree.
All other product names, trademarks or logos mentioned herein are
used for identification purpose only, and may be the trademarks or
registered trademarks of their respective owners.
The purchase of the product described herein shall not be deemed to
grant, either directly or by implication, estoppel or otherwise, any
license under the copyrights, patents, patent applications or trademarks
of Hannspree, except for the normal, non-exclusive use that arises by
operation of law in the sale of a product.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Introducing the TV
Thank you for purchasing this LCD TV. Your LCD TV is designed to be safe,
versatile, and easy to use. The design makes it a fun addition to any room.
You can watch broadcast or cable television channels, and easily connect a
VCR, VCD, DVD player or a game device to the standard RCA and S-Video
input ports that are included in the 4-IN-1 A/V cable. You can also connect
your TV to a PC and use the TV as an external monitor.
Convenient control buttons located on the TV and a handy remote control let
you change channels, adjust the volume, and change display settings
through an easy-to-use on-screen display menu system. The built-in stereo
speakers provide full rich sound and a convenient audio output port lets you
connect to an external audio system or headphones.
Features
•
•
•
•
•
•
Built-in TV tuner
4-IN-1 A/V cable
On-Screen Display (OSD) menu system
Built-in stereo speakers
3D Comb Filter
Advanced de-interlacing
15
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Checking Package Contents
Make sure the following components are included in the box. Please contact
Hannspree Customer Service immediately if anything is missing or
damaged.
•
•
•
•
•
•
•
•
•
•
•
TV
User’s manual
Quick start guide
Warranty and service manual
Power cord
Power adapter
4-IN-1 A/V cable
Remote control and battery/batteries
RCA jack x 3
VGA cable
Stop Card
16
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Getting Started
Control Panel
Description
Icon
Function
Turns the TV on and off.
0
/
On Off
Power
Indicates power status.
Power LED
In TV/AV mode, press this button to
mute the audio. Automatically
adjusts the screen parameter in PC
mode.
MUTE
AUTO
MUTE A
0
0
0
Mute (Auto)
AUTO
0
Selects the input source to be
displayed
(TV/CATV, AV, AV1,AV2 or PC).
SOURCE/S/
MENU/M/
Source
Menu
Turns the On-Screen Display (OSD)
menu on and off.
Changes channels. Press channel up
to increase the channel number.
Press channel down to decrease the
channel number. In PC or AV mode,
press either button to return to TV
mode.
channel up
(
/
/ S)
channel down
/ T)
Select
channel
(
/
Press volume up to increase the
audio volume. Press volume down to
decrease the audio volume.
volume up
(
(
/
/ + / S)
Adjust
volume
volume down
/
/ – / T)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Input and Output Jacks
Description
Connector
Function
Connects to a right audio (red)
or left audio (white) cable, or
video (yellow) cable.
AV1 (R-AUDIO/
L-AUDIO/VIDEO)
(Selected models
only)
Use the included 4-IN-1 A/V
cable to connect external
devices, such as a VCR, VCD,
DVD player, CVBS RCA
cables or a game device.
Audio Input: AV connector
audio (white and red) cables.
Video Input: AV connector
video (yellow) or S-Video
cable.
AV2 (AV, AV IN)
Connects to an antenna or
CATV cable television line.
ANT
Connects to the included
power adapter.
DC-IN (DC-12V)
Connects to a PC.
VGA/PC-IN
LINE IN
Connects to a PC's audio line-
out.
Connects to external stereo
speakers.
LINE OUT
Connects to headphones or
external speakers
Headphone jack
( )
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control
Description
Icon
Function
Press this button to activate the OSD
menu system and to adjust various
settings and personal preferences.
MENU
Menu
Arrow
MENU
/
/
ENTER
PressS / T / W and X to scroll
through the on-screen display
menus.
Favorite channels can be selected
using the W and X buttons on the
remote control.
S / T / W / X /
< / >
1
4
2
5
3
6
Use to select a channel directly.
Press 0-9 to enter the channel
number (press 1 and 0 for channel
10).
Number
7
8
0
9
Press this button to return to the last
channel selected.
RECALL / LAST
CC
Recall/Last
Caption/CC
Press this button to enable the
closed captions/subtitles (Only
available in the United States of
America).
Press this button to enable the
bilingual function when the program
has stereo/SAP/MONO capabilities.
MTS
MTS
Power
Turns the TV power on or off.
-VOL VOL+
>VOL VOL<
VOL VOL
Press volume up to increase the
audio volume. Press volume down to
decrease the audio volume.
Adjust volume
VOL VOL
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Description
Icon
Function
Press this button to eliminate sound.
Press mute again or press the
volume adjust buttons to restore
sound.
MUTE
Mute
Changes channels. Press channel
up to increase the channel number.
Press channel down to decrease the
channel number. In PC or AV mode,
press either button to return to TV
mode.
CH CH
CH CH
CH CH+
CH CH
Select channel
Source
Press this button to cycle the video
input sources. The source is
displayed on the screen.
SOURCE
AUTO
Press this button to automatically
adjust the screen parameters in PC
mode.
Auto (selected
models only)
Reset (selected
models only)
RESET
Press this button to reset the TV.
V-Chip (selected
models only)
This button allows you to change
v-chip settings.
V-CHIP
Press this button repeatedly to set
the length of time until the TV turns
off.
Sleep (selected
models only)
SLEEP
Press this button to show messages
on the screen, such as the channel
number and other. Press this button
again to show the real-time clock.
Press this button again to close the
display message.
Display (selected
models only)
DISPLAY
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Inserting the Remote Control Battery/Batteries
Lithium battery/batteries
1
Open the battery compartment cover at the
back of the remote control (A).
A
2 Slide the battery/batteries, with the positive
(+) side facing up, underneath the shorter set
of metal contacts (B).
B
3 Press the battery/batteries firmly into place
C
D
in the battery compartment (C)
4 Replace the battery compartment cover (D).
Note
Your remote control may have either AAA type batteries or CR2032 lithium
battery/batteries.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
AAA battery/batteries
1
Open the battery compartment cover at the
back of the remote control (A).
A
B
C
2 Insert the battery/ batteries paying
attention to the polarity markings inside
the battery compartment (B).
3 Replace the battery compartment cover
(C).
Note
Your remote control may have either AAA type batteries or lithium
battery/batteries.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
•
•
•
If the remote control is not used for a long period, remove the batteries
and store them separately.
Handle damaged or leaking batteries carefully, and wash hands after
such handling.
If your remote control has two batteries, do not mix new and old
batteries because the life of the new batteries will be shortened.
Chemical fluids may leak from the old batteries.
•
Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type recommended by the equipment
manufacturer. Discard used batteries according to manufacturer’s
instructions.
•
•
Refer to your local recycling or waste disposal rules and contact a local
waste disposal vendor to dispose of used batteries.
The remote control may have a magnet in it, so do not place magnetic
sensitive items such as watches, credit cards, or flash media close to
the cover.
•
Do not use force when pulling the remote control cover open; you may
damage the hinge.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Making Connections
Connecting to an Antenna or Cable TV
1
Connect one end of the VHF/UHF (Antenna) or CATV cable to ANT
Jack (VHF/UHF IN Jack) on the back of the TV.
2 Connect the other end of the VHF/UHF (Antenna) or CATV cable to
the antenna socket or CATV cable.
Antenna
ANT
ANT jack
(VHF/UHF IN jack)
Antenna/CATV
socket
Antenna/CATV
coaxial cable
Note
If you cannot receive channels after connecting to an antenna or cable TV
line, try scanning for channels. See “Auto Program” on page 50.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to AV Devices
Connect external devices such as a VCR, VCD or DVD player, or video
game console to the TV using the supplied 4-IN-1 A/V cable.
Connecting to a VCR/VCD/DVD Player
The illustration presented here shows how to connect the TV to a VCR,
VCD or DVD player. Actual connections may vary according to the make
and model of the device. Refer to the user’s manual included with the device
for more detailed instructions.
VCR
DVD
VCD
AV2
4-IN-1 A/V jack
B
R W Y
S-Video
connector
AV
connectors
4-IN-1 A/V cable
Note
•
The cables are color-coded (black, red, white, yellow). Connect each
color-coded cable to the appropriate connector on your device.
•
When connecting the S-Video connector and AV connector at the same
time, the priority is given to the S-Video connector.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a Video Camera
The instructions presented here are a general guide to connecting the TV to
a camcorder or other type of digital camera. Actual connections may vary
according to the make and model of the device. Refer to the user’s manual
included with the camcorder or camera for more detailed instructions.
S
WB
AV2
4-IN-1 A/V jack
S-Video
connector
B
R
W
4-IN-1 A/V cable
Y
AV connectors
Note
The cables are color-coded (black, red, white, yellow). Connect each color-
coded cable to the appropriate connector on your device.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a Video Game Console
The instructions presented here are a general guide to connecting the TV to
a game console using the RCA Jacks (some game devices may require a
unique adapter that is not provided). Actual connections may vary according
to the make and model of the game device. Refer to the user’s manual
included with the game console for more detailed instructions.
AV2
4-IN-1 A/V jack
AV
B R W Y
connectors
S-Video
connector
4-IN-1 A/V cable
Notes
•
Connect the 4-IN-1 A/V cable connectors to the corresponding
connectors on your game device adapter.
•
If the 4-IN-1 A/V cable does not fit the game device, then insert RCA jack
between the 4-IN-1 A/V cable and game device.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting External Speakers or Headphones
External speakers or headphones may be used to listen to the TV rather
than using the built-in speakers. Connect external speakers to the speaker
line out port or headphones to the headphone port as illustrated.
Headphones
HEADPHONE/
Headphone
jack
LINE OUT
Speaker line
out port
Speakers
Notes
•
External speakers or headphones are not included with the TV.
•
The internal TV speakers will not output sound when headphones are
plugged in.
•
Use external speakers with built-in amplifiers only.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a PC
You can connect the TV to a PC and use it as an external monitor. Connect
the TV’s VGA/PC-IN port to the PC’s VGA port. Connect the TV’s line in port
to the PC’s line out port to listen to the PC’s audio output on the TV’s
speakers. Refer to the following illustration.
VGA
LINE IN
Line out
VGA cable
PC-IN
VGA port
Line out
PC link cable
VGA port
Note
You can connect the line out port of a CD-ROM player, stereo, or other
device to the TV’s line in port to listen to the devices audio output.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Power Adapter
1
Connect the power cord to the power adapter as illustrated.
2 Plug the power adapter connector into the DC-IN input jack on the
rear panel of the TV.
3 Insert the three-pronged plug at the other end of the power cord into
a power outlet.
Three-pronged
plug
Power outlet
DC-IN
DC-IN
Power cord
Power adapter
30
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Using the TV
Using the Remote Control
For best results, use the remote control within a distance of 16 feet
(5 meters) from the front of the TV. Do not exceed an angle of 30 degrees
when pointing at the TV.
Notes
•
The operational distance may be shortened when the signal sensor is
directly exposed to strong light.
•
Aim the transmitter on the remote control at the signal sensor and
ensure that there are no obstacles between them.
Turning the TV On and Off
0
/
1
Press power
on the TV.
On Off on the remote control or control panel to turn
0
/
On Off
2 Press power
again; the TV is in off mode.
Selecting Channels
Press channel up or channel down on the control panel to select the
channel or enter the specific channel number by pressing the number
buttons on the remote control.
Switching Source Signals
Press source to select the incoming source signal.
The current source setting (TV/CATV, AV, AV1,AV2 or PC ) appears on the
upper left corner of the screen.
Adjusting the Volume
Press volume up to increase the volume. Press volume down to decrease
the volume. The volume level is displayed on the screen.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
10 Adjusting On-Screen Display (OSD)
Settings
The On-Screen Display (OSD) menu system provides a quick and simple
method to adjust your TV’s settings. This chapter describes how to change
each of the available settings.
The OSD can be used with either the remote control or the control panel.
Function
Menu
Control Panel Icon
Menu
Button
Menu
Remote Control Icon
MENU/ENTER, M
Channel
up
Right arrow
CH (
/
/
/ + / S)
/ – / T)
/ X
Channel
down
Left arrow
Enter
/ W
CH (
Enter
Menu
MENU/ENTER, M
Note
The following sections explain how to adjust settings in the OSD menus
using the control panel.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD Setting Menu
PC
Brightness&Contrast
Brightness
30
30
Press menu to enter the OSD
Contrast
menus. The Main Menu appears.
Return
Select
Menu OK
Note
To exit the OSD menus, press channel up or channel down to select Exit
. Then press menu to exit the OSD menus. Also, after you finish setting
OSD parameters, follow these instructions to exit the OSD menus.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Brightness
1
Press menu to enter the OSD menus.
2 Press menu again to enter the
Brightness & Contrast menu.
3 Press channel up to increase the
brightness. Press channel down to
decrease the brightness.
PC
Brightness&Contrast
Brightness
2
5
Contrast
4 Press menu to select Return.
5 Press channel down to exit the
Brightness & Contrast menu.
Return
Adjust
Menu Next
Note
The new setting is confirmed
automatically when the OSD times out.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Contrast
1
Press menu to enter the OSD menus.
PC
2 Press menu again to enter the
Brightness & Contrast menu.
3 Press menu to select Contrast.
4 Press channel up to increase the
contrast. Press channel down to
decrease the contrast.
Brightness&Contrast
Brightness
2
5
Contrast
Return
Adjust
Menu Next
5 Press menu to select Return.
6 Press channel down to exit the
Brightness & Contrast menu.
Note
The new setting is confirmed
automatically when the OSD times out.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Setting
PC
Press menu to enter the OSD
menus.
Audio Setting
Treble
Bass
1
Press channel up or channel
Balance
SRS
L
R
down to select Audio Setting.
ON
ON
OFF
OFF
Mute
2 Press menu to enter the Audio
Return
Setting menu.
Select
Menu OK
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Treble
PC
1
Press menu to enter the OSD menus.
Audio Setting
2 Press channel up or channel down to
select Audio Setting.
Treble
Bass
Balance
SRS
L
R
On
On
Off
Off
3 Press menu to enter the Audio
Setting menu.
Mute
Return
Adjust
Menu Next
4 Press channel up to increase the
treble. Press channel down to
decrease the treble.
5 Press menu to select Return.
6 Press channel down to exit the Audio
Setting menu.
Note
The new setting is confirmed
automatically when the OSD times out.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Bass
PC
1
Press menu to enter the OSD menus.
Audio Setting
2 Press channel up or channel down to
select Audio Setting.
Treble
Bass
Balance
SRS
L
R
On
On
Off
Off
3 Press menu to enter the Audio
Setting menu.
Mute
Return
Adjust
Menu Next
4 Press menu to select Bass.
5 Press channel up to increase the
bass. Press channel down to
decrease the bass.
6 Press menu to select Return.
7 Press channel down to exit the Audio
Setting menu.
Note
The new setting is confirmed
automatically when the OSD times out.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Balance
PC
1
Press menu to enter the OSD menus.
Audio Setting
2 Press channel up or channel down to
select Audio Setting.
Treble
Bass
Balance
SRS
L
R
On
On
Off
Off
3 Press menu to enter the Audio
Setting menu.
Mute
Return
Adjust
Menu Next
4 Press menu to select Balance.
5 Press channel up to change the
balance to the right speaker. Press
channel down to change the balance
to the left speaker.
6 Press menu to select Return.
7 Press channel down to exit the Audio
Setting menu.
Note
The new setting is confirmed
automatically when the OSD times out.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
SRS
This option enables the 3D Surround Sound feature.
PC
1
Press menu to enter the OSD menus.
Audio Setting
2 Press channel up or channel down to
select Audio Setting.
Treble
Bass
Balance
SRS
L
R
On
On
Off
Off
3 Press menu to enter the Audio
Setting menu.
Mute
Return
Adjust
Menu Next
4 Press menu to select SRS.
5 Press channel down to turn the SRS
on. Press channel up to turn the SRS
off.
6 Press menu to select Return.
7 Press channel down to exit the Audio
Setting menu.
Note
The new setting is confirmed
automatically when the OSD times out.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Mute
PC
1
Press menu to enter the OSD menus.
Audio Setting
2 Press channel up or channel down to
select Audio Setting.
Treble
Bass
Balance
SRS
L
R
On
On
Off
Off
3 Press menu to enter the Audio
Setting menu.
Mute
Return
Adjust
Menu Next
4 Press menu to select Mute.
5 Press channel down to turn the mute
on. Press channel up to turn the
mute off.
6 Press menu to select Return.
7 Press channel down to exit the Audio
Setting menu.
Note
The new setting is confirmed
automatically when the OSD times out.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Setting
PC
Press menu to enter the OSD
menus.
Video Setting
G
R
Hue
1
Press channel up or channel
Saturation
Sharpness
Color Temp
down to select Video Setting.
Standard
Menu OK
2 Press menu to enter the Video
Return
Select
Setting menu.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Hue
1
Press menu to enter the OSD menus.
PC
2 Press channel up or channel down to
select Video Setting.
Video Setting
G
R
Hue
Saturation
Sharpness
Color Temp
3 Press menu to enter the Video
Setting menu.
Standard
Menu OK
Return
Adjust
4 Press channel down to increase the
red hue. The image becomes more
red. Press channel up to increase
the green hue. The image becomes
more green.
5 Press menu to select Return.
6 Press channel down to exit the Video
Setting menu.
Note
The new setting is confirmed
automatically when the OSD times out.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Saturation
1
Press menu to enter the OSD menus.
PC
2 Press channel up or channel down to
select Video Setting.
Video Setting
G
R
Hue
Saturation
Sharpness
Color Temp
3 Press menu to enter the Video
Setting menu.
Standard
Return
Adjust
Menu Next
4 Press menu to select Saturation.
5 Press channel up to increase the
saturation. The screen image
becomes more vibrant. Press
channel down to decrease the
saturation. The screen image
becomes less vibrant.
6 Press menu to select Return.
7 Press channel down to exit the Video
Setting menu.
Note
The new setting is confirmed
automatically when the OSD times out.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Sharpness
PC
1
Press menu to enter the OSD menus.
Video Setting
2 Press channel up or channel down to
select Video Setting.
G
R
Hue
Saturation
Sharpness
Color Temp
Cold
3 Press menu to enter the Video
Setting menu.
Return
Adjust
Menu Next
4 Press menu to select Sharpness.
5 Press channel up to increase the
sharpness. Press channel down to
decrease the sharpness.
6 Press menu to select Return.
7 Press channel down to exit the Video
Setting menu.
Note
The new setting is confirmed
automatically when the OSD times out.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Color Temperature
PC
1
Press menu to enter the OSD menus.
Video Setting
2 Press channel up or channel down to
select Video Setting.
G
R
Hue
Saturation
Sharpness
Color Temp
Cold
3 Press menu to enter the Video
Setting menu.
Return
Adjust
Menu Next
4 Press menu to select Color Temp.
The following choices are available.
Warm
Press channel up or channel down to
select Warm.
Standard
Press channel up or channel down to
select Standard.
Cold
Press channel up or channel down to
select Cold.
5 Press menu to select Return.
6 Press channel down to exit the Video
Setting menu.
Note
The new setting is confirmed
automatically when the OSD times out.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Setting
PC
Press menu to enter OSD
menus.
TV Setting
TV/CATV
MTS
CATV
Stereo
Yes
1
Press channel up or channel
No
Auto Program
down to select TV Setting.
Manual Program
Favorite Channel
Return
2 Press menu to enter the TV
Setting menu.
Select
Menu OK
47
Download from Www.Somanuals.com. All Manuals Search And Download.
TV/CATV
PC
1
Press menu to enter the OSD menus.
TV Setting
2 Press channel up or channel down to
select TV Setting.
TV/CATV
MTS
TV
Stereo
Yes
No
Auto Program
Manual Program
Favorite Channel
Return
3 Press menu to enter the TV Setting
menu.
Adjust
Menu Next
4 Select one of the following.
Receiving Broadcast TV
Press channel up or channel down to
select TV when using an antenna to
receive TV.
Receiving Cable TV
Press channel up or channel down to
select CATV STD when connected to
cable.
5 Press menu to select Return.
6 Press channel down to exit the TV
Setting menu.
Note
The new setting is confirmed
automatically when the OSD times out.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
MTS
PC
1
Press menu to enter the OSD menus.
TV Setting
2 Press channel up or channel down to
select TV Setting.
TV/CATV
MTS
CATV
Stereo
Yes
No
Auto Program
Manual Program
Favorite Channel
Return
3 Press menu to enter the TV Setting
menu.
Adjust
Menu Next
4 Press menu to select MTS. The
following choices are available.
STEREO
Press channel up or channel down to
select Stereo (default), the default
audio signal belonging to a particular
channel.
SAP
Press channel up or channel down to
select SAP (Secondary Audio
Program), an audio channel used
with the NTSC TV standard for
auxiliary transmission of such items
as foreign language broadcasting.
This option may not be available in
your local area.
MONO
Press channel up or channel down to
select Mono, which outputs sound
through a single channel.
5 Press menu to select Return.
6 Press channel down to exit the TV
Setting menu.
Note
The new setting is confirmed
automatically when the OSD times out.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto Program
1
Press menu to enter the OSD menus.
PC
2 Press channel up or channel down to
select TV Setting.
TV Setting
TV/CATV
MTS
CATV
Stereo
Yes
No
Auto Program
3 Press menu to enter the TV Setting
menu.
Manual Program
Favorite Channel
Return
Adjust
Menu Next
4 Press menu to select Auto Program.
5 Press channel down to select Yes.
Channel indicator values range from 2
to 69 (antenna connection) or from 1 to
125 (CATV cable connection).
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual Program
This function allows you to search preset channels or to erase previously
preset channels.
PC
1
Press menu to enter the OSD menus.
TV Setting
2 Press channel up or channel down to
select TV Setting.
TV/CATV
MTS
CATV
Stereo
Yes
No
Auto Program
Manual Program
Favorite Channel
Return
3 Press menu to enter the TV Setting
menu.
Adjust
Menu Next
4 Press menu to select Manual
Program.
PC
5 Press channel up to enter the
Manual Program menu.
Manual Program
2
Manual Program
Down
Add
Up
Add/Erase
Erase
6 Press channel up or channel down to
find the channel you want to add.
When you have found the channel,
see the next section “Channel
Add/Erase” to add or erase the
channel.
Return
Adjust
Menu Next
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Channel Add/Erase
After you found a channel using Manual Program, follow the following
instruction to add or erase the channel.
PC
1
Press menu to select Add/Erase.
Manual Program
2
Up
Erase
2 Select one of the following option.
Manual Program
Down
Add
Add/Erase
Add Channel
Press channel down to select Add.
The channel is added to the channel
list.
Return
Adjust
Menu Next
Erase Channel
Press channel up to select Erase.
The channel is erased from the
channel list.
When you return to the normal TV
screen and use channel up and
channel down to browse channels,
an erased channel (for example,
Channel 3) is skipped automatically.
Note
You can still access the erased channel
by entering the channel number using the
number keys on the remote control.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Favorite Channel
Use the Favorite Channel function to save up to four channels for quick
access.(Only available in the United States of America)
PC
1
Press menu to enter the OSD menus.
TV Setting
2 Press channel up or channel down to
TV/CATV
MTS
CATV
Stereo
Yes
select TV Setting.
No
Auto Program
Manual Program
Favorite Channel
Return
3 Press menu to enter the TV Setting
menu.
Adjust
Menu Next
4 Press menu to select Favorite
Channel.
5 Press channel up to enter the
Favorite Channel menu.
PC
6 Press menu to select (M1, M2, M3,
or M4) from the list.
Favorite Channel
M1
M2
M3
M4
2
2
2
2
7 Press channel up or channel down to
select a channel number.
8 Press menu to select Return.
9 Press channel down to return to the
previous menu.
Return
Adjust
Menu Next
Note
Favorite channels can be selected using
theW and X buttons on the remote
control.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
PC Setting
1
Connect TV to a PC.
2 Press source to select PC.
3 Press menu to enter the OSD
menus.
PC
PC Setting
50
16
H.Position
V.Position
Phase
0
4 Press channel up or channel
down to select PC.
Clock
1688
More Option
Return
Select
Menu OK
5 Press menu to enter the PC
menu.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Horizontal Position
PC
1
Press menu to enter the OSD menus.
PC Setting
2 Press channel up or channel down to
select PC Setting.
50
H.Position
V.Position
16
0
Phase
Clock
3 Press menu to enter the PC Setting
menu.
1688
More Option
Return
Adjust
Menu Next
4 Press channel up to move the display
to the right. Press channel down to
move the display to the left.
5 Press menu to select Return.
6 Press channel down to exit the PC
Setting menu.
Note
The new setting is confirmed
automatically when the OSD times out.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Vertical Position
PC
1
Press menu to enter the OSD menus.
PC Setting
2 Press channel up or channel down to
select PC Setting.
50
16
H.Position
V.Position
Phase
0
Clock
3 Press menu to enter the PC Setting
menu.
1688
More Option
Return
Adjust
Menu Next
4 Press menu to select V.Position.
5 Press channel up to move the display
up. Press channel down to move the
display down.
6 Press menu to select Return.
7 Press channel down to exit the PC
Setting menu.
Note
The new setting is confirmed
automatically when the OSD times out.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Phase
PC
1
Press menu to enter the OSD menus.
PC Setting
2 Press channel up or channel down to
select PC Setting.
50
16
H.Position
V.Position
Phase
0
Clock
3 Press menu to enter the PC Setting
menu.
1688
More Option
Return
Adjust
Menu Next
4 Press menu to select Phase.
5 Press channel up to increase the
phase. Press channel down to
decrease the phase.
6 Press menu to select Return.
7 Press channel down to exit the PC
Setting menu.
Note
The new setting is confirmed
automatically when the OSD times out.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Clock
PC
1
Press menu to enter the OSD menus.
PC Setting
2 Press channel up or channel down to
select PC Setting.
50
16
H.Position
V.Position
Phase
0
Clock
3 Press menu to enter the PC Setting
menu.
1688
More Option
Return
Adjust
Menu Next
4 Press menu to select Clock.
5 Press channel up to increase the
clock. Press channel down to
decrease the clock.
6 Press menu to select Return.
7 Press channel down to exit the PC
Setting menu.
Note
The new setting is confirmed
automatically when the OSD times out.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
DOS Mode
1
Press menu to enter the OSD menus.
PC
2 Press channel up or channel down to
select PC Setting.
PC Setting
50
16
H.Position
V.Position
Phase
0
3 Press menu to enter the PC Setting
menu.
Clock
1688
More option
Return
Adjust
Menu Next
4 Press menu to select the More
Option.
PC
5 Press channel up to enter more
option.
More Option
Text
DOS Mode
Color Temp
User R :
User
30
30
30
6 Press channel up or channel down to
select Text or Graphics mode.
User G :
User B :
Return
Adjust
Menu Next
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Color Temperature
PC
1
Press menu to enter the OSD menus.
PC Setting
2 Press channel up or channel down to
select PC Setting.
50
16
0
H.Position
V.Position
Phase
Clock
3 Press menu to enter the PC Setting
menu.
1688
More option
Return
Adjust
Menu Next
4 Press menu to select the More
Option.
PC
5 Press channel up to enter More
Option.
More Option
DOS Mode
Text
Color Temp
Return
Standard
6 Press menu to select Color Temp.
Adjust
Menu Next
Warm
Press channel up or channel down to
select Warm.
Standard
Press channel up or channel down to
select Standard.
Cold
Press channel up or channel down to
select Cold.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
PC
User
More Option
Text
The User option enables users to
make their own color settings.
Press channel up or channel down to
select User. The user menu appears.
– Press menu to select User R, User
G, or User B.
DOS Mode
Color Temp
User R :
User
30
30
30
User G :
User B :
Return
Adjust
Menu Next
– Press channel up or channel down
to increase or decrease the
selected color temperature.
7 Press menu to select Return.
8 Press channel down to exit the More
Option menu.
Note
The new setting is confirmed
automatically when the OSD times out.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Miscellaneous Setting
PC
Press menu to enter the OSD
menus.
Miscellaneous
English
Language
Sleeper
1
Press channel up or channel
down to select Miscellaneous.
Press menu to enter the
Miscellaneous menu.
OFF
ON
OFF
OSD Display
Time Setting
More Option
2
Return
Select
Menu OK
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Language
PC
1
Press menu to enter the OSD menus.
Miscellaneous
2 Press channel up or channel down to
select Miscellaneous.
English
Language
Sleeper
Off
On
Off
OSD Display
Time Setting
More Option
3 Press menu to enter the
Miscellaneous menu.
Return
Adjust
Menu Next
4 Press channel up or channel down
to select a language.
5 Press menu to select Return.
6 Press channel down to exit the
Miscellaneous menu.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Sleeper
The Sleeper turns the TV off automatically after a set period of time.
1
Press menu to enter the OSD menus.
PC
2 Press channel up or channel down to
select Miscellaneous.
Miscellaneous
English
Language
Sleeper
Off
On
Off
OSD Display
Time Setting
More Option
3 Press menu to enter the
Miscellaneous menu.
Return
Adjust
Menu Next
4 Press menu to select Sleeper.
5 Press channel up or channel down to
select a power off time:
– OFF
– 30 minutes
– 60 minutes
– 90 minutes
– 120 minutes
6 Press menu to select Return.
7 Press channel down to exit the
Miscellaneous menu.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD Display
When set to Off, the OSD display (source data on top left corner of the TV
screen) turns off after approximately 5 seconds. When set to On, the OSD
does not turn off automatically.
PC
1
Press menu to enter the OSD menus.
Miscellaneous
2 Press channel up or channel down to
select Miscellaneous.
Language
Sleeper
English
Off
On
Off
OSD Display
Time Setting
More Option
3 Press menu to enter the
Miscellaneous menu.
Return
Adjust
Menu Next
4 Press menu to select OSD Display.
5 Press channel down to select On.
Press channel up to select Off.
6 Press menu to select Return.
7 Press channel down to exit the
Miscellaneous menu.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Time Setting
This setting allows you to set the TV clock.
PC
1
Press menu to enter the OSD menus.
Miscellaneous
2 Press channel up or channel down to
select Miscellaneous.
English
Language
Sleeper
Off
On
Off
OSD Display
Time Setting
More Option
3 Press menu to enter the
Miscellaneous menu.
Return
Adjust
Menu Next
4 Press menu to select Time Setting.
5 Press channel up to enter the Time
Setting menu.
6 Press menu to select the Hour or
Minute.
PC
Time Setting
AM -12-
-12-
Hour
:
7 Press channel up or channel down to
decrease or increase the time.
8 Press menu to select Return.
9 Press channel down to exit the Time
Setting menu.
Minute :
Return
Note
The new setting is confirmed
automatically when the OSD times out.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
More Option
This setting allows you to set the OSD background, closed caption function,
parental control features, and reset the TV.
PC
1
Press menu to enter the OSD menus.
Miscellaneous
2 Press channel up or channel down to
select Miscellaneous.
English
Language
Sleeper
Off
On
Off
OSD Display
Time Setting
More Option
3 Press menu to enter the
Miscellaneous menu.
Return
Adjust
Menu Next
4 Press menu to select More Option
setting.
PC
More Option
5 Press channel up to enter the More
Option menu.
OSD Background
C . Caption
Off
Parental
6 Press menu to select OSD
Background, C.Caption, Parental,
Reset, or Return.
Reset
Return
Adjust
Yes
No
Menu Next
67
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD Background
This setting allows you to make the OSD background transparent or
opaque.
PC
1
Enter the More Option menu.
More Option
OSD Background
2 Press channel down to make the
background transparent. Press
channel up to make the background
opaque.
C . Caption
Parental
Off
Reset
Return
Adjust
Yes
No
Menu Next
3 Press menu to select Return.
4 Press channel down to exit the More
Option menu.
Note
The new setting is confirmed
automatically when the OSD times out.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Caption (Closed Caption)
This setting allows you to select closed caption subtitles or text information
broadcast with the program1.
PC
1
Enter the More Option menu.
More Option
OSD Background
2 Press menu to select C.Caption.
3 Press channel up to select CC1,
CC2, CC3, CC4, Text1, Text2,
Text3, Text4, or Off.
C . Caption
Parental
Off
Reset
Return
Adjust
Yes
No
Menu Next
4 Press menu to select Return.
5 Press channel down to exit the More
Option menu.
1. Closed Caption is only available in the United States of America.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Parental
The Parental Control Function (V-CHIP) is used to block program viewing
based on the ratings sent by the broadcast stations1. The United States has
two rating systems for viewing contents, TV Parental Guidelines, and movie
ratings. The TV Parental Guidelines work in conjunction with the V-CHIP to
help parents screen out inappropriate television programs from their
children. Movie ratings are used for original movies rated by the Motion
Picture Association of America (MPAA) as watched on cable TV and not
edited for television. The V-CHIP can also be set to block MPAA-rated
movies.
PC
1
Enter the More Option menu.
More Option
OSD Background
2 Press menu to select Parental.
3 Enter the password number using the
remote control keypad.
C . Caption
Parental
Off
Reset
Return
Adjust
Yes
Menu Next
PC
No
4 Press X (on the remote control) to
submit the password.
The Parental submenu appears.
Enter Password
Submit
Return
Adjust
Menu Next
PC
Note
To use parental control functions, a
password must be entered. The default
password is 0000. The password may only
be entered using the remote control. If the
wrong password is entered, “Wrong
Password” is displayed. See “Change
Parental
V - Chip
Off
MPAA Rating
TV Rating
Change Password
Return
Adjust
Menu Next
1. Parental functions are only available in the United States of America and
is contingent upon the availability of the TV network programming.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
V-Chip
This setting allows you to turn the V-chip functions on or off.
PC
1
Enter the More Option menu.
Parental
2 Press menu to select Parental.
3 Enter the password number using
the remote control keypad.
V - Chip
Off
MPAA Rating
TV Rating
Change Password
4 Press menu to select Submit.
5 Press X (on the remote control) to
submit the password.
Return
Adjust
Menu Next
The Parental submenu appears.
6 Press the menu button to select
V-Chip.
7 Press channel up to toggle the
V-chip function on or off.
8 Press menu to select Return.
9 Press channel down to return to the
More Option menu.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
MPAA Rating
The MPAA rating menu allows you to block or unblock broadcast programs
based on their movie rating.
PC
1
Enter the More Option menu.
MPAA Rating
2 Press menu to select Parental.
3 Enter the password number using
the remote control keypad
G
- Allow -
- Allow -
- Allow -
- Allow -
PG
PG13
R
NC17
X
Return
- Allow -
- Allow -
4 Press menu to select Submit.
5 Press X (on the remote control) to
submit the password.
Adjust
Menu Next
The Parental submenu appears.
6 Press menu to select MPAA Rating.
7 Press channel up to display the
MPAA submenu.
8 Press menu to select a rating to
change.
9 Press channel up to allow or block
the selected rating.
10Press menu to select Return.
11 Press channel down to return to the
Parental menu.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Rating
The TV Rating menu allows you to block or unblock broadcast programs
based on their TV rating.
PC
1
Enter the More Option menu.
TV Rating
2 Press menu to select Parental.
3 Enter the password number using
the remote control keypad.
TV - Y
- Allow -
- Allow -
- Allow -
- Allow -
TV - Y7
TV - G
TV - PG
TV - 14
TV - MA
Return
- Allow -
- Allow -
4 Press menu to select Submit.
5 Press channel up to submit the
password.
Adjust
Menu Next
The Parental submenu appears.
6 Press menu to select TV Rating.
7 Press channel up to display the TV
Rating submenu.
8 Press menu to select a rating to
change.
9 Press channel up to allow or block
the selected rating. The Blocked
Content menu will display.
10Press menu to select Return.
11 Press channel down to return to the
Parental menu.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Ratings
MPAA Ratings
G
–
–
–
–
Suitable for a general audience, all children
Parental guidance suggested
Parental guidance for children under 13 suggested
Restricted viewing. Parental guidance suggested for children
under 17
PG
PG-13
R
NC-17
X
–
–
No-one under 17 allowed to view
Adults only
TV Ratings
Age based
TV-Y
TV-Y7
TV-G
–
–
–
Suitable for a general audience, all children
Directed at children aged 7 and older
General audience
TV-PG –
TV-14
TV-MA –
Parental guidance suggested
Parents strongly cautioned
Mature audience only
–
Content based
FV
D
L
S
V
–
–
–
–
–
Fantasy violence
Suggestive dialogue
Strong language
Sexual situations
Violence
Note
More information about the ratings system can be found by visiting these
web sites:
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Change Password
The Change Password function enables you to change the password
needed to access Parental Control features.
PC
1
Enter the More Option menu.
Change Password
2 Press menu to select Parental.
3 Enter the password number using
the remote control keypad.
4 Press menu to select Submit.
5 Press channel up to submit
password.
New
Confirm
Submit
Return
Adjust
Menu Next
6 The Parental submenu appears.
7 Press menu to select Change
Password.
8 Press channel up to display the
Change Password screen.
9 Enter the new password using the
keypad on the remote control.
10Enter the new password again to
confirm.
11 Press channel up to submit the new
password.
12Press menu to select Return.
13Press channel down to return to the
Parental menu.
Notes
•
If the two passwords entered do not
match, the message “Wrong
Password” is displayed.
•
Your password is required to access
any parental control feature in the
future. If you forget your password,
refer to “Troubleshooting” on page
79.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Reset
The Reset function returns all of your TV’s user settings to their factory
defaults.
Warning:
The reset function will erase all of your custom and favorite channel
settings, and will reset all display settings (such as contrast,
brightness, etc.) to the factory default values. The reset function
cannot be reversed once it begins.
PC
1
Press menu to enter the OSD menus.
Miscellaneous
2 Press channel up or channel down to
select Miscellaneous.
English
Language
Sleeper
Off
On
Off
OSD Display
Time Setting
More Option
3 Press menu to enter the
Miscellaneous menu.
Return
Adjust
Menu Next
4 Press menu to select More Option.
5 Press channel up to enter the More
Option menu.
PC
More Option
OSD Background
C . Caption
Off
6 Press menu to select Reset.
7 Press channel down to reset the
OSD settings.
Parental
Reset
Return
Adjust
Yes
No
Menu Next
By default, No is already selected
(highlighted in yellow). The TV
immediately resets when Yes is
selected and you see the message on
the screen.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
11 Taking Care of Your TV & Remote
Control
Turn the power off before you begin cleaning the
TV.
For best results, use a clean lens cloth to
remove dust and fingerprints from the screen.
Do not wipe the shell of the TV with alcohol,
methanol, gasoline or oil products to avoid
GAS
OIL
damaging the finish. Wipe the shell with a dry
soft cloth and use neutral cleaning fluids.
If your model has leather components, wipe the
leather parts with a dry cloth and keep the area
dry. Place the TV far from sources of steam to
avoid making the leather wet.
Be careful to disconnect the power plug
correctly. Hold the plug. Do not attempt to
disconnect the plug by pulling on the power cord.
Arrange and store the power cord neatly as
shown to the left to avoid knotting or bending
which may cause fire due to damage or electric
leakage.
Note
Protect the remote control from shock or vibration to avoid damage.
Do not place the remote control in hot or humid locations.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Troubleshooting
Situation
Solution
•
•
•
Connect the power cord properly.
Check if the power LED is on or not.
Press power on the control panel or remote
control.
•
Press source to cycle through connected
video sources.
No picture and sound.
•
•
•
Press channel up or channel down to
switch to other TV stations.
Check the TV/CATV OSD settings. See
Make sure all cables are connected
properly.
•
•
Check the antenna and cable connections.
Adjust the brightness in the OSD menus.
No picture, or poor picture, sound is OK.
Picture is not in color.
•
•
Adjust the saturation in the OSD menus.
Make sure all cables are connected
properly.
•
•
Make sure the source device is functioning
properly.
Make sure the audio cable is connected
securely.
Picture is OK, no sound.
•
•
Turn the mute off.
Press volume up on the control panel or
remote control.
•
Make sure the MTS option is set to Stereo,
•
•
Adjust the balance in the OSD menus. See
Make sure the audio cable is connected
securely.
One of the speakers has no sound.
•
•
Try the Auto Program function in the OSD
“TV Setting” menu. See “Auto Program” on
Cannot receive some TV channels using
cable TV.
Use the Reset function in the OSD menu.
Want to reset TV settings.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Situation
Solution
•
If OSD items are colored in light blue, the
system is in a state such that those settings
are not available.
Cannot operate menus.
Forgot parental control password.
Screen image turns over.
•
•
Use the master password 0928
Make sure the video signal cable is
connected properly.
•
•
Adjust the location of the antenna, placing it
far from roads or sources of interference.
Check the antenna and the video signal line
connections.
Snow appears on the screen.
Blurred or overlapped images.
•
•
•
Readjust the sharpness setting.
Choose programs with high quality signals.
Adjust the direction of the antenna or
change the video signal cable.
•
•
•
•
Make sure the battery is inserted correctly.
Replace the battery with a new one.
Make sure the TV power cord is plugged in.
Make sure the path between the remote
control and the sensor is clear.
Remote control doesn’t work.
•
Try operating the remote control at a closer
distance to the TV. Refer to “Using the
79
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Specifications
15-inch LCD TV
LCD Panel Size
Aspect Ratio
15-inch TFT
4:3
Display Resolution
TV System
1024 (horizontal) x 768 (vertical)
NTSC
VGA input (15 pin D-SUB / PC link cable), S-Video
Input and Composite Video Input (through the 4-IN-1
A/V cable)
Video System
Audio System
Line in
10-pin mini-DIN (Audio Input with 4-IN-1 A/V cable)
3.5 mm ø headphone port x 1 (Audio Output)
Built-in Speakers
Power Supply
2W + 2W / 3W + 3W
100-240V, 50/60 Hz, 12V DC
60 W Maximum
Power Consumption
Optional Accessories
External Speakers
PC Mode Support Timing
Pixel Format Hor. Freq. (kHz) Hor. Polarity Ver. Freq. (Hz) Vertical Polarity
Standard
DOS_Graphic
DOS_Text
VESA
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
640*400
720*400
640*480
640*480
640*480
800*600
800*600
800*600
800*600
1024*768
1024*768
1024*768
832*624
1024*768
640*480
31.47
31.47
31.47
37.861
37.5
35.156
37.879
48.077
46.875
48.363
56.476
60.023
49.7
-
-
-
-
-
+
+
+
+
-
-
+
-
70
70
60
72
75
56
60
72
75
60
70
75
75
75
67
+
+
-
-
-
+
+
+
+
-
-
+
-
VESA
VESA
VESA
VESA
VESA
VESA
VESA
VESA
VESA
MAC
MAC
MAC
60.2
35
-
-
-
-
81
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Glossary
Aspect Ratio: The ratio of width to height of a film, image or display
screen.
Broadcast TV: Broadcasting video signals using high-frequency
electromagnetic waves to distribute television channels to viewers
(standard TV broadcast).
CATV: Community Antenna Television, the original name for cable
TV. A television distribution system that uses coaxial cable instead of
the traditional radio broadcasting (over-the-air) method to deliver
television, FM radio, and other services to consumers.
Color Temperature: Adjusting the color temperature enables you to
set the intensity of white light. Color temperature is measured in
Kelvin (K). Higher color temperatures result in a blue tint. Lower
temperatures result in a red tint.
Hue: Colors in a color system are measured by hue, saturation and
luminance. Hue indicates the predominant color.
LCD (Liquid Crystal Display): A display technology that uses rod-
shaped molecules (liquid crystals) that flow like liquid and bend light.
MTS: Multi-channel Television Sound. Enables reception of audio
other than the primary (stereo) audio signal. SAP (Second Audio
Program) enables reception of a separate channel that may be a
different language or completely different information such as the
news.
OSD (On-Screen Display): A control panel on the television screen that
allows you to select viewing options.
Saturation: Chromatic purity indicating the amount of white contained
in a color. Fully saturated colors are pure colors; less saturated
colors appear as pastel shades.
Stereo: is the default audio signal belonging to a particular channel.
S-Video: Separate video, a video cabling standard used to transmit
video by keeping brightness (Y) and color information (C) on
82
Download from Www.Somanuals.com. All Manuals Search And Download.
separate channels. Most often used with camcorders, VCRs, and
quality receivers and amplifiers to provide sharper pictures.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
is a trademark of
SRS Labs, Inc.
SRS technology is incorpo-
rated under license from SRS
Labs, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|