LIMITED WARRANTY
™
pureguardian
2-in-1
To the consumer, Guardian Technologies LLC warrants this product to be free of defects in materials
or workmanship commencing upon the date of the original purchase. Refer to your product carton
for the length of warranty and save your original sales receipt to validate start of warranty period.
If this product should become defective within the warranty period, we will repair or replace any
defective parts free of charge. The complete machine must be delivered pre-paid to any authorized
Guardian Technologies LLC warranty service center. Please include complete information on the
problem, day of purchase, copy of original sales receipt and your name, address and telephone
number. If you are not near a warranty station, call the factory for assistance in the US and Canada
at 1-866-603-5900. Use only genuine Guardian Technologies replacement parts.
Upright & Canister
with Silver Clean Technology
The warranty does not include unusual wear, damage resulting from accident, or unreasonable use
of the product. This warranty does not cover unauthorized repairs. This warranty gives you specific
legal rights and you may also have other rights (other rights may vary from state to state in the
U.S.A).
USE & CARE INSTRUCTIONS
We consider the registration process important to ensuring superior service to our customers,
however submitting this card to Guardian Technologies LLC is optional and does not affect your
rights to utilize this warranty according to the conditions stated above. If you have any questions
or comments about our product call toll free at 1-866-603-5900 or send comments to: Attn:
Customer Service, Guardian Technologies LLC, 7700 St. Clair Avenue, Mentor, OH 44060.
Replacement Parts:
HEPA Dirt Cup Filter: FLTB
Exhaust Filter: FLTA
Belt Style: BLT1
English Manual..................E-1
French Manual ..................F-1
Spanish Manual ................S-1
Upright to Canister Model No. GGU300
1 Year Limited Warranty
!
WARNING:
Guardian Technologies LLC
7700 St. Clair Avenue · Mentor, Ohio 44060
Cleaner assembly may include
small parts. Small parts can
present a choking hazard.
1-866-603-5900
©2010 Guardian Technologies LLC
REV0411
1
Download from Www.Somanuals.com. All Manuals Search And Download.
HOSE CRADLE & HOSE ASSEMBLY
HANDLE ASSEMBLY
Handle
· HOSE CRADLE ASSEMBLY
· HANDLE ASSEMBLY
· Set hose cradle on the top of the cleaner. (Fig. 1)
· Insert handle in the handle hole on the top of the body. (Fig. 6)
· Using a Phillips screwdriver, secure the 3/4-inch screw.
· HANDLE DISASSEMBLY
· Push the handle removal button.
· Pull handle upward.
· HOSE ASSEMBLY
· Insert the body end of hose into the hose hole on the top of the cleaner. (Fig. 2)
· Line up circular tab on hose cuff with inner groove. (Fig. 2)
· Connect and twist clockwise to secure proper hose connection. (Fig. 3)
· Place hose in hose cradle. (Fig. 4)
Protrusion
to lock
Handle
Hole
· Insert the base end of the hose into the hose inlet on the base of the cleaner. (Fig. 5)
Handle
Removal
Button
Fig. 6
BASE ASSEMBLY
· BASE ASSEMBLY
· Set the body on the top of the base. (Fig. 7)
· Use both sides of the guide feature on the base.
Fig. 1
Fig. 2
Fig. 3
· BASE DISASSEMBLY
· Push the release canister pedal.
· Lift up the body.
Body
Guides
Release
Canister
Pedal
Hose
Base Hose
Connector
Base
Fig. 4
Fig. 5
Fig. 7
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOL ASSEMBLY
CONVERTING TO CANISTER MODE (cont.)
· Attach crevice tool, dusting brush and upholstery
brush into storage area on the back of the vacuum. (Fig. 8)
· Push handle removal button and pull up on handle to disconnect from body. (Fig. 13)
· Insert hose into handle hose connector and twist clockwise to lock in position. (Fig. 14)
· Push button on wand to extend telescoping wand. (Fig. 14)
· Insert end of handle into hard floor nozzle. (Fig. 15)
Crevice
Tool
· Canister mode. (Fig. 16)
Dusting
Brush
Fig. 8
Upholstery
Brush
Handle
UPRIGHT MODE
Hose
Hose
Handle
Connector
USING IN UPRIGHT MODE
· Push the handle release pedal. (Fig. 9)
· Turn main power switch on. Turn brush power switch on.
Telescoping
Button
Handle
Removal
Button
Caution: The headlight and brush does not come on when in the upright position even if the
switch is on. You must release the handle for the brushroll to begin spinning. (Fig. 10)
Handle
Base Safety
Switch
Base
Handle
Release
Pedal
Fig. 13
Fig. 14
Fig. 9
Fig. 10
CONVERTING TO CANISTER MODE
CONVERTING TO CANISTER MODE
· Remove hose from base hose connector. (Fig. 11)
Handle
· Step on release canister pedal and pull body upward by canister handle. (Fig. 12)
Hard Floor
Nozzle
Canister
Handle
Body
Hose
Fig. 15
Fig. 16
Release
Canister
Pedal
Base Hose
Connector
Base
Fig. 11
Fig. 12
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
HEIGHT ADJUSTMENT KNOB
STORING
CLEANING & REPLACING FILTER
· Rotate the height adjustment knob to the
correct carpet height. (Fig. 17)
· After using the cleaner, store in
upright mode.
To optimize the vacuum performance you should clean the filter each time you empty the dirt cup.
· Lift up the dirt cup cover, rotate and remove the inner filter. (Fig. 21)
· To clean bare floor, set this knob to the
bare floor position and turn off the brush
power switch. (Located on the top of the
cleaner, see page 2)
· Store accessories on the storage clips
located on the cleaner body.
· Wrap the cord around the cord storage
hooks on the side of the body and hang
the plug at the cord clip on the wand.(Fig. 18)
· Tap the inner filter on a trash bin to remove the dust from the pleats. (Fig. 22)
Note: This inner filter is washable and can be rinsed if you notice a reduction in vacuum
performance (suction). To wash, first tap filter to remove excess dirt and dust from the pleats.
Rinse filter clean with warm water then allow to completely dry (a minimum of 24 hours) before
returning to dirt cup. Use filter: FLTB for inner dirt cup.
Dirt Cup Cover
Fig. 17
Fig. 18
Cord
Clip
Tap Gently
HEPA
Inner Filter
r
Cord
Plug
Fig. 21
Fig. 22
CLEANING DIRT CUP
· You will need to empty dirt cup when dust reaches the “FULL” line.
· Turn off the cleaner and unplug from electrical outlet.
EXHAUST FILTER CLEANING & REPLACEMENT
· Grasp the dirt cup handle and depress button, pull out the dirt cup from body. (Fig. 19)
· To empty, remove the dirt cup and hold over trash bin. Push the dirt release button
and dispose of the dirt. (Fig. 20)
· Pull out the exhaust filter. (Fig. 23)
· Replace the exhaust filter when it becomes dirty. (Fig. 24) Use filter: FLTA for exhaust filter.
Caution: This filter is not washable.
Filter Frame
Filter
Dirt
Release
Button
Exhaust
Filter
- FULL
- FULL
Body
Fig. 24
Body
Fig. 20
Dirt Cup
Dirt Cup
Release Button
Fig. 23
Note: Replacement parts can be purchased by calling 1-866-603-5900.
Fig. 19
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
BELT REPLACEMENT
TROUBLESHOOTING GUIDE
Warning: Before replacing the belt, make sure the cleaner is unplugged from electrical outlet.
· Turn off the cleaner and unplug from electrical outlet.
· Remove the bottom plate of the base by removing the 5 screws using a Phillips screwdriver.
(Fig. 25)
Please check each item below if you have trouble with your cleaner. Before checking, ensure that
the cleaner is unplugged from the power supply.
PROBLEM
PROBLEM
SOLUTION
· Set the new belt over motor pulley. (Fig. 26) Use belt: BLT1.
· Slip the brushroll into the belt and reassemble. (Fig. 27)
· Replace the bottom plate and secure the 5 screws.
Cleaner won’t run.
1. Power cord not firmly
plugged into outlet.
1. Plug unit in firmly.
2. Motor protector tripped.
2. Cool down and press the reset
button. (See page 3)
3. Need service.
3. Take to service center or call
1-866-603-5900
Motor
Pulley
Brushroll won’t spin.
1. Cleaner is not in the
upright mode.
1. The brush only turns on when the
handle is released for vacuuming.
The brush does not come on in
the upright position even if the
switch is on. Depress handle for
brushroll to start turning.
(See page 5)
Fig. 25
Fig. 26
Fig. 27
2. Brush switch is off.
3. Brushroll is jammed.
4. Belt is broken or off
motor pulley.
2. Make sure the brush switch is in on.
3. Remove it and clean debris, hair, etc.
off of brush, then replace.
4. Replace the new belt or correct
belt securing. (See page 10)
HEADLIGHT REPLACEMENT
· Turn off the cleaner and unplug from electrical outlet.
Cleaner or tool won’t
pick up dirt.
1. Incorrect height setting.
1. Rotate setting knob to correct
height setting. (See page 7)
2. Grasp hose tube and firmly push
onto base.
3. Try to remove clog by squeezing out
of hose.
· Press the handle release pedal and use the handle to place the body in a flat position.
· Remove the headlight cover by removing the screw with Phillips screwdriver. (Fig. 28)
· Pull the bulb straight out of the socket. (Fig. 29)
· Install the new bulb, model LBU.
· Replace the headlight cover and secure the screw.
2. Hose not attached to
base.
3. Clogged hose.
4. Dirt cup is full.
4. Empty dirt cup (See page 8), if
washed, after dried well, reinsert it.
Headlight
Cover
Headlight
5. Inner filter is blocked.
6. Crack or hole in hose.
5. Clean it or replace new. (See page 9)
6. Take to service center or call
1-866-603-5900.
Cleaner is difficult to
push.
1. Incorrect height setting.
1. Rotate height setting knob to correct
height setting. (See page 7)
2. Brush switch is off.
1. Dirt cup is full.
2. Make sure the brush switch is in on.
Fig. 28
Fig. 29
Visible dust escaping
from cleaner.
1. Empty dirt cup (See page 8) wash it,
after dried well, replace it.
2. Filter missing or
installed incorrectly.
2. Check inner filter & exhaust filter for
correct installation.
3. Dirt cup installed
incorrectly.
3. Pull out and re-insert dirt cup
correctly.
Note: Replacement parts can be purchased by calling 1-866-603-5900.
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
|