Grundig Flat Panel Television 32 VLC 6121 C User Manual

LCD TV

32 VLC 6121 C

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents_{--------------------------------------------------------------------------------------------------------------------------------------}

48- operAtion-As-A-pC-monitor

48 Connecting a PC

48 Selecting presets for the PC

48 Settings for PC mode

49- operAtion-with-A-Common-

interFACe

49 What is a Common Interface?

49 Inserting the CA module

49 Access control for CI module and

smart card

50- speCiAl-settinGs

51 Searching for digital terrestrial

TV channels automatically

52 Searching for digital terrestrial

TV channels manually

53 Tuning analogue television channels

54 Changing stored analogue channels

56- inFormAtion

56 Displaying signal information

56 Service information for retailers

56 Environmental note

57 Technical data

58 Troubleshooting

-3

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

setup-AnD-sAFetY_{-------------------------------------------------------------------------------------------------------}

Please note the following instructions when

setting up the television set:

Make sure the power cord or the power sup-

ply unit (if provided) are not damaged.

This television is designed to receive and dis-

Only operate the television with the power

supply/power cord provided.

play video and audio signals.

All other uses are expressly prohibited.

Thunderstorms are a danger to all electrical

devices. Even when the television is switched

off, it can be damaged by a lightning strike to

the mains or the antenna. Always disconnect

the mains and antenna plugs during a storm.

The ideal viewing distance is five times the

diagonal screen size.

Light falling on the screen impairs picture

quality.

Use a damp, soft cloth to clean the screen.

Do not use water with soap or detergent.

To ensure the device is always adequately

ventilated, make sure there is sufficient space

between the television set and nearby furniture

(min 10 cm).

Only clean the housing of your television set

with the cloth provided. Do not use water with

soap or detergent.

The television is designed for use in dry rooms.

If you do use it outdoors, make sure it is pro-

tected from moisture such as rain or splashing

water.

When deciding where to put the device, re-

member that furniture is often coated with vari-

ous types of varnish and plastic. Many of these

contain chemicals which can corrode the feet

of the device, leaving marks on the surface of

the furniture which can be difficult or impossi-

ble to remove.

Never expose the television set to moisture.

Do not place any vessels such as vases on the

television, as they may spill liquid, thus present-

ing a safety risk.

The screen of your LCD television meets

the highest quality standards and has been

checked for pixel faults.

Despite the great care taken in manufacturing,

technological reasons make it impossible to

completely discount the possibility that some

pixels may be faulty.

Provided they are within the thresholds speci-

fied by the DIN norm, pixel faults of this kind

cannot be regarded as a defect as defined by

the warranty.

Place the television on a hard, level surface.

Do not place any objects such as newspapers

on the television or put cloth or similar items

under it.

Do not place the television close to heating

units or in direct sunlight, as this will impair

cooling.

Heat build-up can be dangerous and shortens

the service life of the television. For reasons of

safety, have a repairman remove any dirt in

the television from time to time.

To ensure fires do not occur,

always keep candles and other

open flames away from the device.

Never open the television under any circum-

stances. Warranty claims are excluded for

damage resulting from improper handling.

-4

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

setup-AnD-sAFetY_{-------------------------------------------------------------------------------------------------------}

Do not connect any other equipment while the

device is switched on. Also switch off other

equipment before connecting it.

Do not plug in the power cord of the device

until you have connected the external equip-

ment and the antenna.

To avoid safety problems arising from the bat-

teries used with the product, follow the instruc-

tions below.

In case of misplacement of batteries, they may

cause explosion due to short circuit.

Do not expose the batteries to excessive heat

such as direct sunlight, fire, etc.

Do not use old and unused batteries together.

Only replace the exhausted batteries with

those having the same model, value and prop-

erties.

To avoid environmental health problems aris-

ing from the product, batteries and accesso-

ries.

Make sure the mains plug is freely accessible.

Caution:

If you plan on using a wall bracket for your

television, make sure you read the assembly

manual for the wall bracket or have a spe-

cialist assemble it.

When purchasing the wall bracket, make

sure that all the fastening points on the televi-

sion are also on the wall bracket and that

they are all used when mounting it.

-5

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

GenerAl-inFormAtion_{----------------------------------------------------------------------------------}

Using the time shift function, you can quickly

special-features-of-your-

and easily pause a programme using the re-

-television-set

mote control and resume it at a later stage.

You can receive and watch digital TV channels

The programme is recorded in an external

using your television set (via DVB-T and DVB-C)

data medium.

– including High Definition programmes (HD).

You can record any digital TV channels you

However, the reception of digital TV channels

choose.

in HD is currently limited to a few countries in

The TV channels are converted by the televi-

Europe.

sion and saved on an external data medium

Although this television set complies with the

current DVB-T and DVB-C standards (status:

which is connected to the USB socket.

The saved programmes can be called up and

August 2010), the compatibility with future ter-

played from the archive on the external data

restrial DVB-T and DVB-C cable programmes

medium at any time.

cannot be guaranteed.

You can also play a programme from the

archive while recording another.

More information on recording and playing

TV programmes can be found on page 24.

Your television set can receive and process

all analogue and non-encrypted digital

TV channels. The television set is also equipped

with digital and analogue receivers.

The electronic TV guide (for digital channels

only) informs you about any schedule changes

at short notice, and provides an overview of

all the broadcasters' schedules for the next few

days. Detailed information on the individual

television programmes are – when provided

by the broadcasting station – are also avail-

able in the electronic TV guide.

You can connect various data media, such as

an external hard drive, a USB memory stick or

a digital camera, to the USB socket. Using the

file browser, you can then select and play the

file formats of your choice (for example, MP4,

MP3 or JPEG data).

-6

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

GenerAl-inFormAtion_{----------------------------------------------------------------------------------}

receiving-digital-channels

You require a digital roof antenna or indoor

antenna (passive or active indoor antenna

with its own power supply) to receive digital

television channels (DVB-T).

important-notes-on-

environmental-protection

The following information will help you to save

resources – and money as well.

If you are not using your television set for

If you wish to receive digital television chan-

several days, you should pull out the mains

plug for environmental and safety reasons.

This way the television does not consume any

electricity.

nels via your cable system (DVB-C), the an-

tenna cable for your cable operator must be

connected to the television set.

Unlike analogue broadcasting, not every

As switching off the television set does not

channel has its own transmission frequency.

Instead, several channels are grouped into

what are known as bouquets on a regional or

national level. You can find the current trans-

mission information on teletext from various

broadcasters, or by consulting a current TV

guide or the Internet.

completely disconnect it from the mains, pull

out the plug to disconnect it from the mains

completely.

If the device is equipped with a power switch,

switching it off using this switch will be suffi-

cient. The energy consumed by the television

set is reduced to virtually 0 W.

Various digital television channels from private

In standby mode, the television set uses very

broadcasters are encrypted (DVB-T and DVB-

C). Watching these channels and the record-

ing and playback functions are only possible

with the appropriate CI module and a Smart-

Card. Ask your specialist dealer.

little energy. However, it may be necessary to

leave the television set in standby mode for cer-

tain functions (for example automatic switch-on

and switch-off and for timer functions).

The range of channels available from the pub-

lic broadcasting institutions (ARD with EinsEx-

tra, EinsFestival or ZDF with ZDF Info and all

third party broadcasters) are not encrypted

and can be received without a SmartCard.

The television set uses less energy when the

brightness is reduced.

-7

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

ConneCtion-AnD-prepArAtion_{------------------------------------------------}

Connecting-the-antenna-and-power-cord

1a To receive terrestrial digital broadcasters

(DVB-T) connect the cable for the rooftop

or indoor antenna (passive or active indoor

antenna with its own power supply) to the an-

tenna socket »Ant-in« on the television set;

Plug the power cord into a wall socket.

note:

Do not plug in the power cord of the device

until you have connected the external equip-

ment and the antenna.

Only use the power cord supplied to connect

1b To receive digital cable channels (DVB-C)

connect the cable for the rooftop antenna

to the antenna socket »Ant- in« on the

television set;

the television set to a suitable earthed safety

socket.

Do not use an adapter plug or extension

lead which does not meet the applicable

safety standards. Do not tamper with the

power cord.

1c To receive analogue TV channels, connect

the cable for the rooftop antenna to the an-

tenna socket »Ant-in« on the television set

note:

When connecting an indoor antenna you

may have to try it out at different positions

until you get the best reception.

-8

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

ConneCtion-AnD-prepArAtion_{------------------------------------------------}

environmental-note

inserting-batteries-into-the-

-remote-control

This symbol on recharge-

able batteries/batteries

or on the packaging indi-

cates that the rechargea-

ble battery/battery may not be disposed of

with regular household rubbish. For certain

rechargeable batteries/batteries, this sym-

bol may be supplemented by a chemical

symbol. Symbols for mercury (Hg) or lead

(Pb) are provided if the rechargeable batter-

ies/batteries contain more than 0.0005%

mercury or more than 0.004% lead.

Rechargeable batteries/batteries, including

those which do not contain heavy metal,

may not be disposed of with household

waste. Always dispose of used batteries

in accordance with local environmental

regulations. Make enquiries about the appli-

cable disposal regulations where you live.

Open the battery compartment by removing

the lid.

Insert the batteries (2 x 1.5 V micro, for

example R03 or AAA). Observe the po-

larity marked in the bottom of the battery

compartment.

Close the battery compartment.

note:-

If the television no longer reacts properly

to remote control commands, the batteries

may be flat. Always remove used batteries.

The manufacturer accepts no liability for

damage caused by leaking batteries.

-9

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

overview_{-------------------------------------------------------------------------------------------------------------------------------------}

Connections-on-the-television-set

Av1-/-s-vhs

SCART socket (CVBS signal,

RGB signal);

Video and sound socket for

S-Video camcorder.

optic-out

Socket for audio output

(optical) for PCM/AC3

signals.

For connecting digital AV

amplifiers or AV receivers.

Component

Audio

pC-in

Socket for audio

input for a PC.

---pb-pr-Y/Av2 Sockets for video input

(YUV signal).

l--r

Sockets for audio input

VGA socket, video input

for PC.

(YUV signal);

Audio socket for

camcorder.

Ant-in

Antenna socket for a DVB-T,

DVB-C and analogue

antenna.

Y/Av2-

-Video socket for

camcorder

-10

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

overview_{-------------------------------------------------------------------------------------------------------------------------------------}

hDmi2

hDmi3

HDMI socket,

Controls-on-the-television-set

audio/video input.

8/i-

Switches the television on and

back into standby mode.

HDMI socket,

audio/video input.

v–--v+

menu-

Adjusts the volume;

Headphone jack (3.5 mm

jack plug);

Sockets for audio output.

selects menu functions.

-Opens the menu.

Select a menu option with

»p+« or »p–«.

usB

-USB socket for external

data media without a power

supply of their own and

PVR function.

Activate the function with

»v+«.

Confirm the function with

»v+« or »v–«..

hDmi1

Ci- -

HDMI socket,

audio/video input.

Press »menu« to quit the menu.

sourCe- Opens the pre-selection for

AV channels.

-Common Interface Slot.

In the menu, press »p+« or »p–«

to select and press »sourCe« to

confirm.

p–--p+

Switches the television on from

standby;

selects channels in steps;

selects function in the menu.

-11

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

overview_{-------------------------------------------------------------------------------------------------------------------------------------}

the-remote-control-–-main-functions

Switches on from standby;

Selects channel – directly

Switches on and off

(Standby).

Selects the channel list

(»All«, »FAV 1« to »FAV 4«).

Switches between

teletext and TV mode.

Opens the selection menu to

change picture formats.

Opens the »HDMI CEC De-

vice List«.

Then select with » « or » «

and press »oK« to confirm.

Displays information.

-Zapping function;

switches back one menu

level in the menus.

Opens the main menu

-Opens the channel list.

Opens the electronic

TV guide.

Opens the TOOLS menu.

Adjusts the volume.

Opens menu for AV channels

and USB input.

Then select using »

v«, » «,

» « or » « and press »oK«

to confirm.

Muting

Switches on from standby;

Selects channel – in steps.

Record, play, pause and

stop (only digital television

channels - to/from external

USB device).

Opens the »PRnP« menu.

navigation-in-the-menus

and down in the menus.

right in the menus.

-Activates various functions and

save functions/settings.

-12

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

overview_{-------------------------------------------------------------------------------------------------------------------------------------}

the-remote-control-–--

All-functions

Selects different subtitles

(only for digital television chan-

nels)

» «-(red)-

Selects pages in teletext;

Selects/activates various



Selects different audio lan-

guages (only for digital televi-

sion channels)

« (green)



« (yellow) functions in the menus.





« (blue)

Starts the recording (

digital television channels

recording is made on an exter-

nal data medium).

only for

, the



Starts playing a programme

from an external data medium;

Repeats a recorded pro-

gramme.

Freeze frame, if no external

data medium is connected;

Playback pause;

Time shift mode (only for digital

television channels and when

an external data medium is

connected).

Ends playback of a pro-

gramme from an external data

medium;

Ends a recording or

playback in time shift mode;

Splits the screen in teletext.

Switches to double character

size in teletext;

Selects the next title/next pic-

ture in the file browser.

Refreshes a teletext page;

Selects the previous track/pre-

vious picture in the file browser.

Stops scrolling through pages

in teletext;

Starts a fast reverse search in

the file browser.

Reveals answers in teletext;

Starts a fast forward search in

the file browser.

-13

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

settinGs_{------------------------------------------------------------------------------------------------------------------------------------------}

selecting-language,-country-and-

operating-mode

initial-set-up-and-tuning-

-television-channels

The television set is equipped with automatic

channel search, which searches for terrestrial

channels (DVB-T), cable channels (DVB-C) and

analogue channels.

Switch on the television set from standby with

»8«, »1…0« or »p+« or »p-«.

– During initial set-up, the »Installation Guide«

will be displayed.

You start the search and can then copy the tel-

evision channels into four favourite lists and sort

them there into your order of preference.

help:-

If this menu is not displayed, restore the

television set to its default settings (see

page 41).

For DVB-T and DVB-C channels 1000 presets,

and 100 presets for analogue channels.

2- Select the menu language with » «, » «,

»v« or »

Λ« and press »oK« to confirm.

the-various-settings

3- Select the mode with » « or » « and press

Depending on the type of antenna connected,

you can decide which channels you would like

the television to search for.

»oK« to confirm.

– The settings used in »Home Mode« help to

save energy.

Tunes digital terrestrial television channels, on

page 15.

– Alternatively, the menu item »Shop Mode«

can be selected which the retailer can use

for demonstrating the device functions.

Tunes digital television channels from the

cable provider, on page 15.

note:

End the »Shop Mode« by restoring the tel-

Tunes analogue television channels, in the

evision set to its default settings (see page

41).

chapter “Special functions”, starting on page

53.

4- Select the country in which the television set

Further settings for digital television channels

is operated with » «, » «, »v« or »Λ« and

after the initial set-up can also be found in the

chapter “Special functions”, starting on page

50.

press »oK« to confirm.

– The »Source Setup« menu appears with the

»Connection Type« line marked.

note:-

note:

Make the language and country selection for

all types, then continue reading the respective

chapter.

You can find a description of how to tune

the television channel of your choice – de-

pending on the antenna connected – in the

following chapters.

-14

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

settinGs_{------------------------------------------------------------------------------------------------------------------------------------------}

tuning-terrestrial-television-

channels-(DvB-t)

tuning-television-channels-from-

the-cable-provider-(DvB-C)

In the »Source Setup« menu, in the »Connec-

tion Type« line, select the option »Cable«

with » « or » «.

In the »Source Setup« menu, in the »Connec-

tion Type« line, select the option »Air« with

» « or » «.

Select the line »Scan Type« with »

«.

Use » « or » « to set the required scan

v« or

Select the line »Scan Type« with »

«.

Use » « or » « to set the required scan

v« or

»Λ

type:

– »DTV«, scan for digital television channels;

– »ATV«, scan for analogue television

channels;

– »DTV«, scan for digital television channels;

– »ATV«, scan for analogue television

channels;

–

»ATV & DTV«, scan for analogue and

digital television channels.

–

»ATV & DTV«, scan for analogue and

digital television channels.

Select the line »Cabel Scan Type« with »

or » «. Select the preferred option (»Quick«

or »Full«) with » « or » «.

– The search function »Quick« sets up the

channels according to the information pro-

vided by your cable provider in the trans-

mission signal.

v«

Caution:

The antenna power supply (5V ) may only

be switched on if the antenna is an active

indoor antenna with a signal amplifier and it

is not already supplied with a voltage via a

mains plug (or similar supply). Otherwise

you may cause a short circuit and irrepara-

bly damage your antenna.

– If the option »Full« is selected, the entire

frequency range will be scanned. The

search can take a long time with this op-

tion. This option is recommended if your

cable provider does not support the scan

Select the line »Active Antenna Power« with

or »Λ«.

Switch on the antenna power supply for the

antenna with » « or » « (»On«).



type

»Quick«.

Start the scan with » « (green).

note:

– The »Search Results« menu appears, and

the search for TV channels begins.

– Depending on the number of television

channels received, this can easily take a

few minutes.

You can accelerate the search. To do this,

you need information about the frequency

and network ID. You are usually able to get

this data from your cable operator or find it

in forums on the Internet.

– The scan is complete as soon as the »PRO-

GRAM TABLE« appears.

Start the scan with » « (green).



–

The »Search Results« menu appears, and

the search for TV channels begins.

note:

You can abort the scan by pressing

»menu«.

– Depending on the number of television

channels received, this can easily take a

few minutes.

– The scan is complete as soon as the »PRO-

GRAM TABLE« appears.

Press »menu« to end the setting.

note:

You can abort the scan by pressing

»menu«.

Press »menu« to end the setting.

-15

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

settinGs_{------------------------------------------------------------------------------------------------------------------------------------------}

selecting-channel-lists

Changing-the-program-table-for-

the-digital-channels

Open the menu with »menu«.

Channels which are found using the scan are

saved in the »PROGRAM TABLE«.

Select the »SOURCE SETUP« menu with »v«

or »Λ« and press »oK« to confirm.

– The »SOURCE SETUP« menu appears.

You can delete channels which are not required

from the programe table, and lock individual

channels (Parental control).

Select the line »Programe Table« with »v«

or »Λ« and press »oK« to confirm.

– The menu »PROGRAM TABLE« appears.

You can also add channels to the favourites list;

in addition, you can change the order of chan-

nels within the favourites list.

important:

Programe table and favourites lists are

saved separately according to the different

input sources (cable and air).

With » « (green) you can display the channels



which belong to one network.

When opening the programme table, the

respective channel list for the current input

signal appears.

Switch to the next page in the programe table

with »p+« and to the previous page with »p-«.

With »

« (yellow) you can open the »LIST



note:

MANAGEMENT« within the programe table.

In this List Management you can create your

own favourites lists.

If in the Program Table

appears added

to the name of the channel, you need a

CI module and a Smart-Card for watching

these channals.

INSTALLATION

PROGRAM TABLE

Network ALL

Das Erste

Service

ALL

DTV

RADIO

DATA

ATV

ZDF

SAT1

N24

3sat

SAT3

1 Das Erste

DTV

HD Sport

HD Test

10 RTL

DTV

11 HD 1

12 Life

13 Film

14 Promo

15 Sport1

DTV

16 TV Sport

17 Sat.8

18 SKY

19 TV6

20 TV5

DTV

Edit

Network

Manage lists

Sorting

Exit

Select favourites

Back

-16

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

settinGs_{------------------------------------------------------------------------------------------------------------------------------------------}

notes:

Creating-lists-of-favourites

You can save your favourite channels in up to

four favourites lists (FAV 1 to FAV 4).

Repeat steps 2 and 3 if you would like to

change other channels within the same

favourites list.

notes:

Repeat steps 1 to 3 if you would like to

change channels in a different favourites list.

Favourites lists must be created separately

for all input sources (cable and air).

Exit the current favourites list with »

(blue).

– The entire programe table will appear

again.



You can select the favourites list by pressing

»FAv«.

In the »PROGRAM TABLE« menu, switch over

to the list view with » « (yellow).



Deleting-channels

Select the channel of your choice with »

or »Λ«.

v«

In the »PROGRAM TABLE« menu, select the

television channel to be deleted with «,

» « or » « and press » «- (red) to

“Push” the channel into the favourites

Λ«,



lists 1 to 4 with » « or » « and press »oK«

activate.

to confirm.

– The position in the favourites list is marked

with »✔«.

Deletethecurrentchannelwith» «(yellow);



« (blue).

delete all channels with »



– You can enter the same channel in more

than one favourite list.

– Each favourite list can store up to 255

channels.

Confirm the deletion process with »

(green).



Quit the deletion process with » «.

note:

skipping-channels

You can mark television channels which should

be skipped when selecting with » « or » «.

It is still possible to select them using the number

buttons.

Channels can also be deleted from the

favourites lists. Select the channel to be

deleted with »

v«, »Λ«, » « or » « and

press »oK« to delete it.

When deleting a channel from the favourites

list, the order within the favourites list will be

updated.

In the »PROGRAM TABLE« menu, switch over

to the list view with » « (yellow).



Select the preferred channel with »

or » «.

v«

Press »menu« to end the set-up.

sorting-channels-in-the-favourite-list

You can change the order of channels in the

favourites list.

Select the column »Skip« with » « or » «

and use »oK« to mark the channel.

– The channel is marked by »✔«.

In the »PROGRAM TABLE« menu, select the

favourites list »1« to »4«.

note:

Channels can also be reactivated. Select the

channel with » « or » «, then select the

column »Skip« and reactivate the channel

with »oK«

2- Select the channel which should be moved

with » «, » «, » « or » « and mark it with

» «-(red).



Move the channel to its new position with

«, » «, » « or » « and press »oK« to

confirm.

-17

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

settinGs_{------------------------------------------------------------------------------------------------------------------------------------------}

notes:

picture-settings-

You can only select the »Mpeg NR« function

Open the menu with »menu«.

on digital and AV presets.

Select the menu item »PICTURE SETTINGS«

»Mpeg NR« reduces any interference from

artefacts (pixel blocks) from digital pro-

grammes due to MPEG compression (such

as from DVB-T receivers or DVD players).

The »Film Mode« detects and processes

feature films automatically for all channel

sources. This means you will always receive

an optimal picture.

This functions in the modi 480i, 576i and

1080i in TV playback and for other channel

sources.

If the »Film mode« is switched on for pro-

grammes without a feature film signal, minor

problems such as picture freeze, defective

subtitles or fine lines in the picture could

occur.

The function »Dynamic Contrast« adapts the

contrast dynamically and optimally for the

respective picture content.

With »Dynamic Backlight«, the device opti-

mally adapts the background lighting to the

picture content.

The »Backlight« can only be set manually

when the function »Dynamic Backlight« is

deactivated.

»MEMC« will only appear in menus of LCD

products with 200 Hz PPR Feature and LED

products with 400 Hz PPR feature..

with »v« or »Λ« and press »oK« to confirm.

– The »PICTURE SETTINGS« menu appears.

20.09.2010

15:46

PICTURE SETTINGS

Picture Mode

Brightness

Contrast

User

100

Sharpness

Colour

Colour Temperature

Medium

Enhanced picture settings

DNR

Off

Mpeg NR.

Exit

Back

Select the line »Picture Mode«, »Bright-

ness«, »Contrast«, »Sharpness«, »Colour«, or

»Colour Temperature« with »v« or »Λ«.

Select the value with » « or » « and press

»oK« to confirm.

notes:

When changing the values with » « or

Press »menu« to end the setting.

» «, the screen will be split. You can see

the current setting on the left side, the new

setting on the right side.

In the »PICTURE SETTINGS« menu you can

also find other additional settings.

Select the line »DNR«, »Mpeg NR«, »Vibrant

Colour«, »Perfect Clear«, »Film Mode«,

»Gamma«, »Dynamic Contrast«, »Dynamic

Backlight«, »Backlight« or »MEMC« with

v« or »Λ«.

Select the value with » « or » « and press

»oK« to confirm.

-18

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

settinGs_{------------------------------------------------------------------------------------------------------------------------------------------}

Automatic-volume

sound-settings-

Television stations broadcast at different vol-

umes. The automatic volume limiting (AVL) func-

tion means the volume is kept the same when

you switch between channels.

Open the menu with »menu«.

Select the menu item »SOUND SETTINGS«

with »v« or »Λ« and press »oK« to confirm.

– The »SOUND SETTINGS« menu appears.

Select the line »AVL« with »

v« or »Λ« and

20.09.2010

15:46

select the option »On« with » « or » «.

SOUND SETTINGS

note:

If the »SRS TS HD« setting has been selected

in the »Audio Mode« line, the AVL line can-

not be selected.

Volume

Balance

AVL

Off

stereo/two-channel-sound,-mono

Sound Type

Sound Mode

Stereo

Normal

Speech

If the device receives two-channel-sound pro-

grammes, e.g. a film with the original soundtrack

on audio channel B (display: »Dual II«) and

the dubbed version on sound channel A (dis-

play: »Dual I«), you can select the audio channel

you prefer.

Sound Preset

External connections

Audio Output Setup

Accessibility Settings

If the device receives stereo or Nicam pro-

grammes, it switches automatically to stereo

sound (display: »Stereo«).

End

Back

You can switch the sound to »Mono« if the stereo

sound quality is poor.

note:

Select the line »Audio Type« with »

v« or

Additional operations are explained in the

following sections.

»Λ

« and adjust the setting with » « or » «.

stereo-width

volume

This broadens the sound output for stereo pro-

grammes and improves the sound with mono

reception.

Select the line »Volume« with »

« or »

and change the setting with » « or » «.

Balance

Select the line »Audio Mode« with »

or » «.

v«

Select the line »Balance« with »

« or »

and change the setting with » « or » «.

Select the option »Spatial« with » « or » «.

-19

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

settinGs_{------------------------------------------------------------------------------------------------------------------------------------------}

soundeffects

equalizer

This menu offers three preset sound effects

(Music, Natural and Speech) and one setting to

be created by you (User).

Equalizer offers a sound setting that you can cre-

ate.

Equaliser appears in the menu when »Sound

mode« is selected as »Spatial« or »Normal«,

and »Sound Medium« as »User«.

Select the line »Sound Preset« with »

v« or

Λ«.

Select »Equalizer« with »v« or »Λ« and

Select the sound effect »Music«, »Natural«

or »Speech« by pressing » « or » «.

press »oK« to confirm.

The »EQUALIZER« menu appears.

note:

»User« option is active when »Sound mode«

setting is selected as »Normal or »Spatial«.

If the »SRS TS HD« setting has been selected

in the »Sound Mode« line, the »Equalizer«

line will not indicate.

srs-trusurround-hD

SRS TruSurround HD is a patented audio tech-

nology which is integrated into the television set

and only requires the built-in speakers to gener-

ate a Surround Sound effect.

Select the frequency bandwidth »120Hz«

with »v« or »Λ«.

Set the preferred value with » « or » «.

Set the next frequency bandwidth with »

or » « and repeat the setting.

v«

Select the line »Sound Mode« with »

or » «.

v«

Press » « to save the setting.

Select the option »SRS TS HD« with » « or

Audio-description-(Audio-subtitles)

» «.

Audio description is an additional audio channel

for visually-impaired persons. Descriptions are

provided of activities, surroundings, changes of

scene, gestures and actors' facial expressions.

Select the line »SRS Sound Preset« with »

v«

or »Λ«.

Select the sound effect »Music«, »Natural«

or »Speech« with » « or » «.

This audio channel is transmitted simultaneously

with the normal sound on digital channels. Avail-

ability depends on the respective channel and

broadcaster.

Select the line »Audio Description« with »

or »Λ

« and select the option »On« with » «

or » «.

Select the line »Volume« with »

« or »

and change the volume with » « or » «.

exiting-the-setting

Press »menu« to end the setting.

* Under licence from SRS Labs, Inc. TruSurround HD,

SRS and the

symbol are trademarks of

SRS Labs, Inc.

-20

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

television---operAtion_{--------------------------------------------------------------------------------}

Displaying-information

Basic-functions

1- Display information with »?«.

– The display disappears automatically after

a short while.

switching-on-and-off

Press »8«, »1…0« or »p+« or »p-« to switch

on the television from standby mode.

Freeze-frame

Press »8« to switch the television to standby.

If you wish to view a particular scene for longer,

you can “freeze” the frame of the current pro-

gramme.

selecting-channels

Press »1…0« to select presets directly.

Activate the freeze-frame function with »$«.

End the freeze-frame function with »$«.

note:

Select channels step by step with »p+« or

»p-«.

3- Open the channel list with »oK«, select the

preferred television channel with » «, » «,

» « or » « and press »oK« to confirm.

If an external data medium is connected

to the television, the time shift function is

activated with »$«. The time shift function is

described on page 27.

Exit the channel list with »menu«.

selecting-channels-from-lists

You can select channels from various lists (e.g.

all channels, FAV 1 to FAV 4).

picture-settings

Various picture settings are available.

Press »FAv« to open an overview of pro-

grame tables.

Open the Tools menu with »tools«.

Select the menu item »Picture Mode« with

– The overview is displayed.

»v« or »Λ«.

Select a channel list with »

Λ« or »v« and

3- Select »User«, »Eco TV«, »Vivid«, »Natural«,

»Movie«, »Sports« or »Game« by pressing

» « or » «.

open it with »oK«

Select a television channel with »

«, »Λ«,

» « or » « and press »oK« to confirm.

note:

Press »menu« to exit the channel list.

Picture setting »Game« can only be selected

in »HDMI«, »Component« and »PC« modes.

selecting-a-preset-Av-channel

Audio-settings

Various audio settings are available.

Open the »Select Source« menu with »

Select an AV preset with » «, »

» « and press »oK« to confirm.

«.

Λ«, » « or

Open the Tools menu with »tools«.

Use »1…0« to switch back to the television

channel.

Select the menu item »Sound Preset« with

»v« or »Λ«.

Adjusting-the-volume

Select the audio setting »User«, »Music«,

»Natural« or »Speech« by pressing » « or

Adjust the volume with »

«.

- -–

» «.

switching-sound-on/off

note:

Press » « to mute the sound or switch it

on again.

»User« option is active when »Sound mode«

setting is selected as »Normal or »Spatial«.

-21

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

television---operAtion_{--------------------------------------------------------------------------------}

Audio-language

electronic-tv-guide

Various languages are available on digital tele-

vision channels. This depends on the programme

being broadcast.

The electronic TV guide provides an overview of

all programmes that will be broadcast in the next

week (for digital channels only).

Open the selection menu with »

«.

Press »GuiDe« to display channel informa-

tion.

Select the language by pressing »

and press »oK« to confirm.

v« or »Λ«

notes:

Not all channels supply provide a detailed

subtitles

TV guide.

Various subtitles are available on digital televi-

sion channels. This depends on the programme

being broadcast.

Many broadcasters transmit the current

schedule, but do not offer detailed descrip-

tions.

Open the selection menu with » «.

There are broadcasters which do not pro-

vide any information at all.

Select the subtitles with »v« or »Λ« and

press »oK« to confirm.

Press »v« or »Λ« to select a television

channel.

Zoom-function

– Today's programmes on the television

channel selected are displayed.

Open the Tools menu with »tools«.

Select the menu item »Zoom« with »v« or

Switch to the information about the current

»Λ«.

programme with » «.

3- Press- »oK« repeatedly to enlarge the

notes:

display in three steps.

You can open and switch off the extensive

programme information with »?«.

eco-mode

This function allows you to reduce the power

consumption.

You can can added the selected broadcast

to the memory timer by pressing »oK«

Press »

« to select information on the next

Open the Tools menu with »tools«.

Select the menu item »Eco TV« with » « or »Λ«.

programme and, »

« to return to the infor-

mation for the current programme.

3- Switch on the Eco mode with » « or » «.

Select programmes on over the coming days

with » « (green), and switch back to the cur-

Switch the Eco mode off again with » « or » «.



rent day with » «-(red).



Zapping-function

This function remembers the channel you are

currently watching while you switch over to other

ones (zapping).

Switch back to the channel selection with

» «.

note:

Filter for certain programmes with »



(blue), select the channel type with » «,

Press »1…0« or »p+«, »p–« to select the

channel to be stored in the zapping memory

» «, »v« or »Λ« and press »oK« to con-

and press » « to confirm.

firm. Programmes which match the selected

channel type are displayed.

Press »1…0« or »

Λ«, »v« to switch to

another television channel.

7- Quit the electronic TV guide with »menu«.

Press » « to switch between the saved tel-

evision channel and the last television chan-

nel viewed.

4- End the function with »menu«.

-22

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

television---operAtion_{--------------------------------------------------------------------------------}

»panorama«-format-

Changing-the-picture-format

This setting is suitable for films in an especially

wide format.

The television automatically switches to the 16:9

format if this format is detected via the SCART

socket.

During programmes in 4:3 format, the picture is

stretched horizontally if the »Panorama« function

is selected. The picture geometry is stretched

horizontally.

Select the picture format with » «.

– The picture format (for example »16:9«) is

displayed.

– You can choose between the following

picture formats:

»overscan«-format

In this mode, HD pictures are not cropped by the

HDMI sockets or component sockets, and are

displayed in their original size. This only applies

in HDMI mode and for resolutions of 720p or

above.

»Auto«-format

The picture format is automatically switched to

»16:9« for 16:9 programmes.

The picture format is automatically switched to

»4:3« for 4:3 programmes.

»16:9«-and-»14:9«-formats

For programmes in 4:3 format, the picture is

stretched horizontally if the »16:9« format or

»14:9« format is selected.

The picture geometry is stretched horizontally.

With actual 16:9 input sources (from a set-

top box on the SCART socket) the picture fills

the screen completely and with the correct

geometry.

»4:3«-format

The picture is shown in 4:3 format.

»letterBox«-format-

The letterbox format is especially suitable for

programmes in 16:9 format.

The black borders which are usually at the top

and bottom of the screen are eliminated, 4:3 pic-

tures fill the screen.

The transmitted pictures are enlarged, but are

slightly cropped at the top and bottom. The pic-

ture geometry remains unchanged.

»subtitle«-format

If you cannot see the subtitles at the bottom of

the screen, select »Subtitle«.

-23

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

usB-reCorDinG_{---------------------------------------------------------------------------------------------------------------}

possible-limitations-when-using-

an-external-data-medium

Depending on the broadcaster, you may experi-

ence various restrictions on some of the functions

from some television channels.

information-on-recording-and-

playing-television-programmes

Recording and playback of television pro-

grammes is only possible with digital television

channels (DVB-T and DVB-C).

■

The digital television channels (DVB-T and

DVB-C) you are able to record and playback

also depends on the broadcaster.

GrunDiG-has-no-influence-on--

these-restrictions.

■

Recording a programme on the external data

■

Recording and playback of programmes,

medium can be disabled by the broadcaster.

If the message »URI* protected! PVR function

is blocked« appears on the screen, then re-

cording or timeshift is restricted (one recording

possible) or disabled (recording not possible)

by the broadcaster.

as well as the time shift function, can only be

carried out using an external data medium

(hard drive or USB stick). The data medium

should have a minimum storage capacity

of 2 GB.

* URI = User right information (Copyright in-

formation).

■

Recordings can be made with most data media

on the market. However, we cannot guarantee

operation for all data media.

■

If you record and save a programme on the

archive of an external data medium, playback

can be restricted.

The broadcaster can allow you to view this

programme one or more times, but it may only

be available for a certain period of time.

■

If a programme was recorded on an external

data medium, it can only be played back on

your television set. The playback of these pro-

grammes is not possible on other devices.

■

If you send your television to be repaired and

■

Programmes not suitable for minors will require

hardware components need to be replaced,

you might not be able to play the recordings

again on the repaired television.

the input of a PIN number immediately before

recording starts. If this authorisation is not

given, the recording may not start.

■

Reception for SKY broadcasting service is cur-

rently only possible in Germany with a suitable

set-top box or suitable CA module.

■

Copying a programme from a digital television

channel onto a video or DVD recorder using

the »Av- 1« socket (analogue picture/

sound signal) can also be restricted by the

broadcaster. Prerequisite is that your device

supports the copying function.

■

Grundig does not accept liability for any loss

of saved data on an external data medium.

-24

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

usB-reCorDinG_{---------------------------------------------------------------------------------------------------------------}

notes:

Connecting-external-data-media-

If you use a network cable for external hard

notes:

disks which have been connected to the

Before connecting the data medium, switch

the television to standby with

the device and then switch the television on

again.

»usB« socket of the television, this network

»8«. Connect

cable must also be disconnected from the

power supply when the television is switched

off.

Before removing the external data medium,

the television must be switched to standby,

so that no data loss occurs.

External data media may not be disconnect-

ed from the television while files on the data

medium are being accessed.

Your television features two USB sockets,

»usB«.

settings-for-usB-recording

selecting-the-menu

»usB« is used to connect data media,

which require an additional power supply

– for example, external hard disks.

Open the menu with »menu«.

Select the line »USB RECORDING« with

v« or »Λ« and press »oK« to confirm.

– The »USB RECORDING« menu appears.

20.09.2010

15:46

USB RECORDING

PRnP

Auto Preview

Manage data medium

Safely Remove Disk

Disk

USB

Partition

Capacity Used

1249

Used (MB)

Total (MB)

38145

Connect the »usB« socket of the television

and the corresponding socket of the data

medium (external hard disk) using a USB ca-

ble;

Remaining SD recording time

Remaining HD recording time

1,008 min

288 min

Exit

Back

insert the USB plug of the USB memory stick

into the »usB« socket of the television.

Confirm the display »

(green).

– The file browser appears.

« with »



-25

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

usB-reCorDinG_{---------------------------------------------------------------------------------------------------------------}

switching-on-automatic-preview

testing-the-external-data-medium

If the automatic preview is switched on, a pre-

view of the selected file appears in the file

browser.

You can subject external data media to a test

and establish whether they are suitable for the

chosen functionality.

Select the line »Auto Preview« with »

«.

v« or

Select the line »Disk« with »v« or »Λ«. If

»Λ

several data media are connected, select the

preferred data medium with » « or » «.

Switch on the function with » « or » «

« or »

(»On«).

Select the line »Partition« with »

Λ«.

If several partitions are available, select the

partition you wish to use with » « or » «.

Press »menu« to end the setting.

safely-remove-disk

Select the line »Check Disk« with »

« or

Select the line »Safely Remove Disk« with

« or » « and press »oK« to confirm.

Λ« and press »oK« to confirm.

Information on the data medium is dis-

played.

»v

–

note:

The disk can now be removed from the

socket.

Press »menu« to end the setting.

selecting-external-data-media

If several external data media are connected to

the television, you can select the preferred data

medium.

Select the line »Disk« with »v« or »Λ«

Select the preferred data medium with » «

or » «.

Press »menu« to end the setting.

selecting-a-partition-on-the-external-

data-medium

If the external data medium features several par-

titions, select the partition you would like to use.

Select the line »Partition« with »v« or »Λ«.

Select the partition you wish to use with » «

or » «.

Press »menu« to end the setting.

-26

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

usB-reCorDinG_{---------------------------------------------------------------------------------------------------------------}

″pausing”-time-shift--

programmes

You can pause the programme you are watch-

ing. This is a useful function, for example if the

telephone rings while you are watching a film

and you do not want to miss anything.

recording-programmes

You can record programmes. The data for these

programmes is recorded on an external data

medium and this archive is administered via the

television.

The following approximate values apply for re-

cording:

Recording time for high-definition programmes

(HD) is 7 minutes with 1 GB of memory,

for standard programmes it is 26 minutes.

A freeze-frame display of the last scene appears

on the screen and the programme is recorded

in the time shift memory of the external data

medium.

While recording, you can watch another pro-

gramme from the archive.

In time shift mode you can record a maximum of

20 minutes of the current programme.

You cannot change presets.

Press »^!« to pause the current programme.

– The picture is frozen, the time shift and the

remaining recording time are displayed.

one-touch-programme-recording

Select the television channel to be recorded

Press »⁸« to resume the programme.

with » »1…0« or »p+«, »p–« and press

–

The programme will continue to be

recorded.

« to start the recording.

– Information on the recording is displayed:

the recording symbol, the channel name,

the programme, the recording time and the

available memory space.

note:

The following functions are possible when in

time shift mode:

– Rewind, press »3« several times accord-

ing to speed (the picture freezes while

rewinding);

– Fast forward, press »4« several times

according to speed;

– Select pause with »!«.

– After a short time this information disap-

pears.

End the recording with »⁷«.

Confirm the display with » « (green);



Press »⁷« to quit the time shift function.

– The message »Live programme« appears,

and you will see the current programme

without time shift.

press » «-(red) to continue the recording.



notes:

After the recording is complete, the record-

– The scenes in the “time shift memory” are

deleted.

ing will be automatically saved on the exter-

nal data medium.

The »RECORDED FILES« menu, with the ar-

chived programmes, can be opened with

»reC.list«.

If the external data medium is disconnected

from the USB socket during recording, the

recording will be stopped automatically

and will not be saved.

Play your recordings, that you have record-

ed with your FAT32 formatted HDDs, in USB

mode.

-27

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

usB-reCorDinG_{---------------------------------------------------------------------------------------------------------------}

recording-a-programme-from-the-

channel-list

presetting-programmes-to-be-

recorded

Open the »CHANNEL LIST« with »oK«

Select a television channel with » «, »

» « or » « and press »oK« to confirm.

...-using-the-electronic-tv-guide

You can use data from the electronic TV guide

for recording.

Λ«,

Press »menu« to exit the channel list.

Press » « to start recording.

25 programmes can be preset for the timer

recording or as a reminder.

– Information on the recording is displayed:

the recording symbol, the channel name,

the programme, the recording time and the

available memory space.

– After a short time this information disap-

pears.

Press »GuiDe« to display channel informa-

tion.

– The electronic TV guide appears.

Select the preferred channel with »

v«

or »Λ«.

Switch to the information about the current

Press »⁷« to stop recording.

programme with » «.

Confirm the display with » « (green);



Select the programme of your choice with

v« or »Λ«.

press » «-(red) to continue the recording.

Confirm the programme with »

«.



– The symbol » « appears after the name

of the programme, and the data has been

added to the timer.

note:

If the data for the recording is to be changed,

use

« (yellow) and

« (blue) to





switch to the »SCHEDULED EVENTS«, press

«(green),changethedataandsaveitwith



« (green)

Press »menu« to exit the menu.

notes:

Before the timer recording begins, a warn-

ing message appears with a 20-second

countdown. You can switch over to the pro-

grammed television channel.

If the timer recording starts during playback,

playback is not interrupted: Recording takes

place automatically in the background as

long as you do not select »Yes« when the

timer countdown message is shown.

-28

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

usB-reCorDinG_{---------------------------------------------------------------------------------------------------------------}

...-by-manual-data-entry

You can preset up to 25 programmes for timer

recording.

editing-recording-data-in-the--

timer-menu

You can edit the data for programmed timer

recordings.

Press »GuiDe« to display channel informa-

tion.

– The electronic TV guide appears.

Select the timer menu by pressing »GuiDe«

 

sion.

« (yellow) and « (blue) in succes-

Open the »MAKE SCHEDULE« menu by

– The »SCHEDULED EVENTS« menu ap-

pears.

pressing » « (yellow) twice.



Select the line »Type« with »v« or »Λ«

Select the title of the programme to be

and select the option »Recording« with » «

changed with »

v« or »Λ« and activate the

or » «.

timer position with

« (green).



– The input menu is displayed.

Select the line »Channel« with »

« or »

and select the channel with » « or » «.

Select the required option with »

« and edit the data with »1…0« and

» « or » «.

v« or

»Λ

Select the line »Mode« with »v« or »Λ« and

select the preferred mode (»Once«, »Every

Day« or »Weekly«) with » « or » «.

4- Save the changes with » « (green).



– The timer has been changed.

Select the line »Start« (Start recording) with

« or » « and enter the date/time with

»1…0«.

Press »menu« to close the menu.

Deleting-recording-data-in-the-timer-

You can delete the data for programmed timer

recordings.

Select the line »End« (Stop recording) with

« or » « and enter the date/time with

»1…0«.

»v

8- Save the data with » « (green).



Select the timer menu by pressing »GuiDe«

 

sion.

– The programme is preset.

« (yellow) and « (blue) in succes-

Press »menu« to exit the menu.

notes:

Before the timer recording begins, a warn-

– The »SCHEDULED EVENTS« menu ap-

pears.

ing message appears with a 20-second

countdown. You can switch over to the pro-

grammed television channel.

Select the title of the programme to be deleted

with »

with

v« or »

Λ« and delete the timer position

« (yellow)



If the timer recording starts during playback,

Press »menu« to close the menu.

playback is not interrupted: recording takes

place automatically in the background as

long as you do not select »Yes« when the

timer countdown message is shown.

-29

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

usB-reCorDinG_{---------------------------------------------------------------------------------------------------------------}

playback

The recorded programmes – whether started

playback-during-a-recording

During a recording, you can either watch the

manually or using the timer function – are stored

programme you are currently recording or watch

on the external data medium. You can open the

a different one that you have already recorded.

archive on the external data medium by pressing

Select the channel to be recorded with

»1…0« or »p+«, »p–« and press »

start the recording.

»reC.list«.

« to

selecting-a-programme-from--

the-archive

Select the »Recorded Event« menu by press-

ing »reC.list«.

Open the »Recorded Event« menu with

»reC.list«

3- Select the programme you want with »

« or

– The menu appears.

« and press »8« to start playback.

Select the programme of your choice with

–

The recording continues in the background.

v« or »Λ« and start playback with »8«.

Press »7« to end playback.

Press »⁷« to end playback.

– The television switches over to the current

television channel.

Press »⁷« to stop recording.

Deleting-programmes-in-the-

recording-list

You can delete programmes from the record-

ing list.

Forward/reverse-picture-search

During playback, select the fast forward

speed (2x, 4x, 8x, 16x or 32x) with »4«;

Open the »Recorded Event« menu with

»reC.list«

during playback, select the rewind speed

(2x, 4x, 8x, 16x or 32x) with »3« (the pic-

ture freezes when rewinding).

– The menu appears.

Select the programme to be deleted with

v« or »

Λ«.

repeating-a-scene-(A-B)

You can mark the starting and ending point of a

scene. The scene is then repeated continuously.

Press »

« (blue) to delete the programme.



Confirm the security query with



(green)

Mark the starting point A by pressing »⁸« at

the required scene during playback.

–

note:

This scene is marked as the starting

point A.

You cannot delete programmes in the

»Recorded Event« menu which are currently

being recorded or played back.

Mark the end point B by pressing »8«

once again at the required scene during

playback.

Press »menu« to close the menu.

– This scene is marked as the end point B.

– The television repeats the programme be-

tween these two points.

Quit the repeat function with »⁷«.

-30

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

usB-operAtion_{----------------------------------------------------------------------------------------------------------------}

image-data

File-formats

Your television can display pictures in the formats

JPEG, PNG and BMP.

Your television can work with the following file

formats using the USB sockets:

JPEG stands for Joint Picture Experts Group.

It denotes a process for compressing picture files.

PNG and BMP are process used to save image

data with no, or very little, losses.

Picture files can be stored with other types of files

on one medium.

These files can be organised into folders and

subfolders.

video-data

Special codecs for video compression and

decompression provide more memory space

without compromising the picture quality exces-

sively.

Your television plays video files in the formats

DIVS, XVID, H.264/MPEG-4 AVC (L4.1, 4 ref-

erence pictures), MPEG-4, MPEG-2, MPEG-1,

MJPEG and MOV.

The following file name extensions are also sup-

ported: AVI, MKV, MP4, TS, MOV, MPG, DAT,

VOB. These files can also contain audio files

compressed using MP3, AAC or Dolby Digital^©.

Audio-data

Your television can play audio data in the for-

mats MP3, AAC, WMA.

MP3 is the abbreviation for MPEG-1 Level 3 and

is based on the MPEG-1 standard, which was

developed by the MPEG (Motion Picture Expert

Group).

AAC stands for Advanced Audio Coding and

was also developed by MPEG. AAC provides

better sound quality at an identical data rate.

WMA (Windows Media Audio) is a compres-

sion standard for audio data developed by

Microsoft.

These formats allow audio files to be recorded

and played which sound as good as a CD, while

taking up only a fraction of the memory space.

File name extensions which are supported: MP3,

MP2, WMA, M4A, AAC.

MP3 files can be organised into folders and

subfolders, as on the computer.

-31

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

usB-operAtion_{----------------------------------------------------------------------------------------------------------------}

Connecting-external--

data-media-

Before connecting the data medium, switch the

television to standby using »8«. Connect the

device and then switch the television on again.

Before removing the external data medium,

the television set must be switched to standby,

so that no data loss occurs.

notes:

If you use a network cable for external hard

disks which are connected to the »usB«

socket on the television, this network cable

must also be disconnected from the power

supply when the television is switched off.

External data media may not be disconnect-

Connect the »usB« socket of the television

and the corresponding socket on the data

device (external hard drive, digital camera,

card reader or MP3 player) using a USB ca-

ble;

ed from the television set while files on the

data medium are being accessed.

A bi-directional data transfer as defined for

ITE (Information Technology Equipment)

devices in EN 55022/EN 55024 is not

possible.

USB transfer is not in itself an operating

mode. It is only an additional function.

insert the USB plug of the USB memory stick

into the »usB« socket of the television set.

Confirm the display »

(green)

– The file browser appears.

« with



-32

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

usB-operAtion_{----------------------------------------------------------------------------------------------------------------}

the-file-browser-

The file browser displays video, audio and

picture files stored on external data media.

settings-in-the-usB--

setup-menu

selecting-the-menu

If an external data medium contains files in

different formats, you can, when necessary, filter

out the formats not required.

Open the menu with »menu«.

Select the »SOURCE SETUP« menu item with

»v

« or »

Λ« and press »oK« to confirm.

main-menu-of-the-file-browser

–

The »USB SETUP« menu appears.

note:

Additional functions are explained in the

following sections.

VIDEO FILES

switching-on-automatic-preview

ROOT

Photo

Music

Film

If this function is switched on, a preview of the

selected file then appears in the file browser.

Select the line »Auto Preview« with »

v«

or »Λ«.

USB DRIVE

Used (MB)

Total (MB)

475

Switch on the function with » « or » «

(»On«).

Use Control

Buttons

Speed

All

Repeat

Now

Total

Press »menu« to end the setting.

selecting-the-display-mode

Select »View Mode« with »v« or »Λ«.

Selected data format.

Total number of folders on the data medium.

2- Select the preferred option with » « or » «.

Press »menu« to end the setting.

3- Preview of the selected file.

setting-the-display-duration-for-

pictures-in-a-slideshow

4- Information on the external data medium.

Menu navigation.

Select »Slide Show Interval« with »v« or »Λ«.

Selectthedisplayduration(3, 5, 10 seconds)

with » « or » «.

Press »menu« to end the setting.

-33

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

usB-operAtion_{----------------------------------------------------------------------------------------------------------------}

Divx^®-voD

Basic-playback-functions-

You must have your device registered in order to

play the protected video that you will buy from

DivX^®.

Select the data medium by pressing »

«,

use » «, » «, » « or » « to select the option

»USB« and press »oK« to confirm.

– The file browser appears.

Select »DivX^®VOD« with »

confirm with »oK«

– Registration Code appears.

v« or »Λ« and

Select the file format (video files, audio files,

picture files) with » « or » «.

Visit “http://vod.divx.com” and register the

device with the registration code.

Switch to the folder/file list with »oK«.

note:

Press »menu« to end the setting.

USB data medium with several partitions is

connected to the USB sockets, the letter for

the respective drive (e.g. C) appears behind

the folder symbol. Select the letter of the

DivX Certified^®to play DivX^®and DivX

Plus™ HD (H.264/MKV) video up to

1080p HD including premium content.

drive with »

confirm.

v« or »Λ« and press »oK« to

ABOUT DIVX VIDEO: DivX^®is a digital video format created

by DivX, Inc. This is an official DivX Certified^®device that plays

DivX video. Visit divx.com for more information and software

tools to convert your files into DivX video.

Select the folder or file with »v« or »Λ« and

press »oK« to open it.

– A list of subdirectories appears.

ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified^®de-

vice must be registered in order to play purchased DivX Video-

on-Demand (VOD) movies. To obtain your registration code,

locate the DivX VOD section in your device USB setup menu.

Go to vod.divx.com for more information on how to complete

your registration.

note:

Switch back to the main folder with » «.

Select the track or picture with »

and press »⁸« to start playing.

You can view information on the film data by

pressing »?«.

v« or »Λ«

–

– When playing MP3 or WMA data, infor-

mation on the album, track and singer is

displayed at the left of the menu.

– When playing picture files, you can use

»?« to display information about the reso-

lution and size.

– When playing picture data, press »

?«

twice to enter the DivX Settings menu.

note:

When playing picture data, the file browser

switches off. Press » « to display the file

browser again.

Press »^!« to pause playback.

7- Press »⁸« to resume normal playback.

Press » « to end playback.

The file browser appears.

-34

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

usB-operAtion_{----------------------------------------------------------------------------------------------------------------}

notes:

Additional-playback--

functions

Depending on the file format, the following

additional functions are available:

Use »Λ« to select »Up Folder«, when you

would like to return to the last folder. Use

»Root« (and then press »oK«) to return to

the main folder.

selecting-chapters-on-Divx^®-files

(only video files)

It is possible that files which are actually

supported do not function correctly in USB

mode. This is because certain files are not

recorded with standardised compression

processes, although they feature the “right”

file ending.

During playback, select the next chapter

with » «.

During playback, select the previous

chapter with » «.

If a video file features several audio tracks

(audio streams), you can switch these over

during playback in full screen mode with

note:

You can also select chapters by entering the

chapter number with »1...0«.

«.

When playing music files, you can use other

options in the USB mode at the same time.

This way, you can, for example, enhance a

slideshow with music.

selecting-titles-on-Divx^®-files

(only video files)

During playback, select the next title with

«.

»Λ

For films, only subtitles in the SRT format

are supported. The names of the subtitle

and film files must be identical. Otherwise,

no subtitles will be shown.

During playback, select the previous title

with » «.

playing-selected-titles

Only the marked tracks are played.

Select the titles with »

»oK« to mark it.

v« or »

« and press

Select the next title with »

« or » « and

press »oK« to mark it.

Start playback with »⁸«.

Press » « to end playback.

note:

To remove the marking, select the title with

« or » « and press »oK« to remove the

marking.

»v

-35

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

usB-operAtion_{----------------------------------------------------------------------------------------------------------------}

selecting-a-track-or-picture-in-steps-

(sKip)

During playback, select the next track/

picture with »⁶«.

During playback, select the previous track/

picture with »⁵«.

– Playback begins with the track or picture

you selected.

selecting-a-certain-passage-for-

playback-

(video files only)

During playback, press »oK«

Enter the passage (time) with »1-...-0« and

press » « (green) or »oK« to confirm.



Fast-forward

(for video and audio files only)

You can select different speeds (2-fold, 4-fold,

8-fold,16-fold and 32-fold forwards and back-

wards).

Select the playback speed during playback

with »3« or »4«.

2- Press »⁸« to resume normal playback.

rotating-pictures-

(picture files only)

You can rotate pictures by 90°.

During playback, press » « or « to rotate

the pictures by 90°.

repeat-functions

Options:

– »One Repeat«: the current track will be

repeated.

– »All Repeat«: all tracks will be repeated.

Open the Tools menu with »tools«.

Select the menu item »Repeat« with »

v« or

»Λ«.

3- Select »All«, »Random«, »One« or »None«

by pressing » « or » «.

-36

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

teletext-operAtion_{-----------------------------------------------------------------------------------------------}

enlarging-the-character-height

If you have difficulty reading the text on the

screen, you can increase the character height.

top-text-or-FloF-text-mode

Press »txt« to switch on teletext.

Select teletext pages directly with »1...0«

To enlarge the character height of a teletext

page, keep pressing »⁵«.

or step by step with »v« and »Λ«.

Return to teletext page 100 with »?«.

note:

page-hold

At the bottom of the screen there is an info

A multiple page may contain several sub-pages,

which are automatically scrolled by the broad-

casting station.

bar with red, green and – depending on the

channel – yellow and blue panels. Similarly,

the remote control also features buttons with

different colours with which these pages can

be selected.

Stop the automatic scrolling of the sub-pages

with »3«.

2- Quit the function with »3«.

Go back a page with » «-(red).



Go to the next page with » « (green).



opening-a-sub-page-directly

Select a particular chapter with



If the selected teletext page contains additional

pages, the number of the current sub-page and

the total number of pages are displayed.

(yellow)

6- Select a particular subject with »

« (blue).



1- Press » « to open the sub-page function.

2- Use » « or » « to select the sub-page.

Quit teletext with »txt«.

normal-text-mode

3- Quit the function with » «.

Press »txt« to switch on teletext.

revealing-answers

Certain teletext pages contain hidden answers

or information.

Press »1…0« to select teletext pages directly.

Return to teletext page 100 with »?«.

Go back a page with »v«.

Display information with »4«.

Go to the next page with »Λ«.

2- Press »4« to conceal the information.

Quit teletext with »txt«.

split-screen

Additional-functions

This functions allows you to display the televi-

sion channel on the left side, the teletext on the

right side.

skipping-the-waiting-time

While a page search is progressing, you can

switch to the TV programme.

Switch the function on with »7«.

– The television channel and teletext are dis-

played next to each other.

Enter the teletext page number with »1…0«

and then press »⁶«.

Switch the function off with »⁷«.

– As soon as the page is found, the page

number is displayed.

Press »⁶« to switch to the teletext page.

-37

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

ConvenienCe-FunCtions_{-------------------------------------------------------------------------}

Changing-the-audio-language

(only for digital television channels)

opening-the-settinGs-menu

Open the menu with »menu«.

You can define a primary and a secondary

audio language.

Select the »SETTINGS« menu with »v« or

Λ« and press »oK« to confirm.

– The »SETTINGS« menu appears.

Select the line »Audio« with »v« or »Λ« and

press »oK« to confirm.

–

The »Select Audio Language« menu

20.09.2010

15:46

appears.

SETTINGS

Select the audio language with » «, » «,

»v« or »

Λ« and then use » «-(red) to set



Language settings

it as the primary audio language, or use

« (green) to set it as the secondary audio



English

language.

Audio

Subtitle

– The primary and secondary language is

display at the top right in the menu.

English

Off

Subtitle Mode

Date and time settings

Press »menu« to end the setting.

Changing-the-subtitle-language-

and-subtitle-mode

(only for digital television channels)

Date & Time

Time Adjustment

Time Zone

Auto

GMT +1

You can switch the subtitles on and off, select the

subtitle language and allocate a second subtitle

language.

Exit

Back

Select the line »Subtitle« with »v« or »Λ«

note:

and press »oK« to confirm.

– The »Select Subtitle Language« menu ap-

pears.

Additional operations are explained in the

following sections.

Select the subtitle language with »

v«,

language-settings

»Λ«, » « or » «, then use » «-(red) to set



it as the primary subtitle language, or use



Changing-the-menu-language

« (green) to set it as the secondary subti-

Select the line »Menu« with »v« or »Λ« and

tle language.

press »oK« to confirm.

– The primary and secondary language is

displayed at the top right in the menu.

–

The »Select Menu Language« menu

appears.

To go back one menu level, press » «.

2- Select the menu language with » «, » «,

Select the line »Subtitle Mode« with »v« or

»v« or »Λ« and press »oK« to confirm.

Λ« and then set the preferred option »Off«,

Press »menu« to finish the setting.

»Hard of Hearing« or »Basic« with » « or

» «.

Press »menu« to end the setting.

-38

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

ConvenienCe-FunCtions_{-------------------------------------------------------------------------}

setting-the-date-and-time

Automatic-setting

Your television set detects the difference in time

to Greenwich Mean Time (GMT) automatically,

as long as the channel selected transmits a time

signal.

timer-settings

entering-the-switch-off-time--

(sleep-timer)

In the »Sleep Timer« menu you can enter a time

for the television to switch off. After this time

has elapsed, the television switches to standby

mode.

Select the line »Time Adjustment« with »v«,

Select the line »Sleep Timer« with »

»Λ«.

v« or

then select the option »Manual« with » «

or » «.

– The lines »Time Zone« and »Daylight Sav-

ing« are active.

Enter the switch-off time with » « or » «.

note:

Select the line »Time Zone« with »v« and

To switch off the function, use » « or » « to

set the switch-off time to »Off«.

press »oK« to confirm.

– The »Select Time Zone« menu appears.

Press »menu« to end the set-up.

3- Select the appropriate time zone with » «,

switch-on-timer

» «, »

v« or »Λ« and press »oK« to con-

firm.

In the »Auto On« menu you can enter a switch-on

time for the television. After the preset time has

elapsed, the television switches on from standby

– at the preselected volume and the preselected

television channel.

Select the line »Daylight Saving« with »

v«

and use » « or » « to set the option »Auto«,

»Off« or »On«.

Press »menu« to finish the setting.

Select the line »Auto On« with

and press »oK« to confirm

»v

« or »

Λ«

manual-setting

You can also set the difference in time manually

– for example, when the correct time is not de-

tected automatically or does not correspond to

local time for other reasons

Select the line »Mode« with

« or » and

Λ«

use » « or » « to select when the television

should switch on.

Select the line »Input Source« with

»v« or »Λ«

and use » « or » « to select the input source.

Select the line »Date & Time« with »

v« or

« and press »oK« to confirm.

Select the line »Service Type« with

»v« or »Λ«

and use » « or » « to select the preferred op-

Select the line »Auto« with »v« or »Λ

« and

tion (ATV, DTV, Radio or DATA).

Select the line »Channel« with

press »oK« to confirm.

– Date and Time will be updated

automatically;

»v« or »Λ«

and use » « or » « to select the preferred

channel.

note:

Select the input box with »v« or »Λ«, enter

the data for Date and Time with »1...0«

and press »oK« to confirm.

The line »Channel« is only active when the in-

put signal currently in use has been set. If no

entry has been made, then the first channel of

the selected input source will be used.

-39

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

ConvenienCe-FunCtions_{-------------------------------------------------------------------------}

Select the line »Volume« with

« or »

and

parental-control-settings

Authorising-programmes

There are films which may be wholly or partially

unsuitable for children.

use » « or » « to set the volume.

Select the line »Set Hour« with

v« or »Λ«

and enter the time with »1…0«.

8- Save the data with » « (green).



These programmes contain information which

marks the content or scenes with access levels of

4 to 18. You can select one of the access levels,

thereby authorising playback.

note:

You can abort the entry by pressing » «-(red)



Press »menu« to end the setting.

Select the line »Parental Guidance« with

« or » « and press »oK« to confirm.

switch-off-timer

»v

In the »Auto Off« menu, you can enter a time

for the television to switch off. After this time

has elapsed, the television switches to standby

mode.

Enter the PIN code »1234« with »1-...-0«.

Select the access level with » « or » «.

Press »menu« to end the setting.

Select the line »Auto Off« with

« or »

Λ«

locking-menus

and press »oK« to confirm

This function allows you to lock the »Automatic

Channel Search«, »Digital Manual Tuning«, »An-

alogue Manual Tuning« and »Program Table«

menus so that they can be only accessed by

entering a PIN code.

Select the line »Mode« with

« or » and

Λ«

use » « or » « to set the preferred mode.

Select the line »Set Hour« with

»v« or »Λ«

and enter the time with »1…0«.

4- Save the data with » « (green).

Select »Menu Lock« with »v« or »Λ«.



note:

Enter the PIN code »1234« with »1-...-0«.

You can abort the entry by pressing » «-

(red).



Activate the lock with » « or » « (»On«).

note:

Press »menu« to end the setting.

To switch off the menu lock, use » « or » «

to select the setting (»Off«).

Automatic-switch-off-(Auto-sleep)

If this function is activated, the television switches

automatically to standby after 5 minutes if no

video signal is broadcast or in accordance with

the according to European regulations, the tel-

evision switches automatically to standby after 4

hours provided that none of the buttons on the

remote control or on the television is operated

during this period.

Press »menu« to end the setting.

locking-keys-(parental-lock)

When the key lock is activated, the buttons on

the television set do not function.

Select the line »Keypad Lock« with »

«.

v« or

»Λ

Enter the PIN code »1234« with »1-...-0«.

Select the line »Auto Sleep« with »

v« or

3- Activate (On) or deactivate (Off) the key lock

»Λ«.

with » « or » «.

Activate the function with » « or » «

Press »menu« to end the setting.

(»On«).

note:

To switch off the function, use » « or » « to

select the setting »Off«.

Press »menu« to end the setting.

-40

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

ConvenienCe-FunCtions_{-------------------------------------------------------------------------}

Changing-the-pin-code

updating-software

You can also enter a personal PIN code instead

of the default code »1234«. Please take note of

your own PIN code.

(for digital channels only)

In the »SETTINGS« menu, select the line

»Check For Updates updates« with » « or

« and press »oK« to confirm.

Select »Set PIN« with »v« or »Λ« and press

»Λ

»oK« to confirm.

– A search for new software will be made

and – if available – it will be installed.

Enter the current PIN code 1 2 3 4 with

»1...0«.

note:

If a search for software updates should be

Enter your new four digit PIN code with

»1...0«.

made automatically, select the line »Auto-

matic OAD« with »v« or »Λ« and use » «

Enter your new four digit PIN code with

»1...0« again.

or » « to select the option »On«.

– The software will be updated automati-

cally as far as possible.

Press »menu« to end the setting.

locking-television-channels-

You can lock individual television channels, for

example channels unsuitable for children, using

a personal PIN code.

restoring-the-television-to-the-

default-settings

This function allows you to delete the channel

lists and all custom settings.

Open the menu with »menu«.

Select the »SOURCE SETUP« menu with »

or »Λ« and press »oK« to confirm.

v«

In the »SETTINGS« menu, select the line

»Restore Factory Defaults« with »v« or »Λ«

Select the line »Program Table« with »

v« or

and press »oK« to confirm.

»Λ« and press »oK« to confirm.

Press » « (green) to confirm the warning



– The »PROGRAM TABLE« menu is dis-

played.

message.

– The »Source Setup« menu appears.

In the »PROGRAM TABLE« menu, switch

Continue the settings with the chapter “Initial

set-up and tuning television channels” on

page 14.

over to the list view with » « (yellow).



Select the channel to be locked with »

v«

or »Λ«.

Select the column »Lock« with » « or » «

and press »oK« to lock the channel.

Enter the PIN code »1234« with »1-...-0«.

– The channel is marked using »✔«.

note:

To remove the lock, select the channel again

with »v« or »Λ«, press »oK« to confirm

and then enter the PIN code 1 2 3 4 using

»1-...-0«.

Press »menu« to end the setting.

-41

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

operAtion-usinG-externAl-DeviCes_{------------------------------}

searching-for-and-activating--

external-devices

You can connect up to 11 devices with DIGI LINK

functions to your television.

DiGi-linK

Your television is equipped with

the DIGI LINK function.

This function uses the CEC

(Consumer Electronics Control)

protocol.

Open the CEC device list with »CeC«.

– The »HDMI CEC Device List« appears.

CEC allows external devices which are connect-

ed to the »hDmi« sockets by an HDMI cable

(e.g. DVD player) to be operated with a remote

control.

Prerequisite is that the devices connected support

CEC. Read the operating manual for the external

device to find out how to activate the correspond-

ing function.

Start the device search with » «-(red).

The devices found are displayed in the

menu.



–

3- Select the device for operation with »

v«,

«, » « or » « and press »oK« to mark it.

– If the selected device is connected to a

different input to the current one, a switch

to the respective input will occur auto-

matically.

the-DiGi-linK-functions-on-your-

television

Press »menu« to end the setting.

switching-on-the-television--

automatically-from-standby

If the »Autom. switch-on TV« function is activated

(»On«), then once the external device (e.g.

DVD player) is switched on, the television also

switches on and the appropriate HDMI preset is

selected.

Automatic-selection-of-the-hDmi-

preset-on-the-television

If your television is switched on and you then

switch on the external device (e.g. DVD player),

the appropriate HDMI preset on the television

will be selected.

selecting-the-menu-language

The television menu language is automatically

selected on the external device (e.g. DVD player).

The external device must support this function.

switching-off-the-external-device-

automatically

If you switch your television to standby, the ex-

ternal device (if it is switched on) will also be

switched to standby.

DIGI LINK is always active on your television set.

-42

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

operAtion-usinG-externAl-DeviCes_{------------------------------}

switching-the-device-to-standby

This option switches the external device to

standby.

Device-operation

You can decide whether external devices should

react to your television's remote control.

Press »

«, use »v«, »Λ«, » « or » « to

Press »

«, use »v«, »Λ«, » « or » « to

select the preset »HDMI1« to »HDMI3« and

press »oK« to confirm.

select the preset »HDMI1« to »HDMI3« and

press »oK« to confirm.

Open the menu with »menu«.

Select the menu item »SOURCE SETUP« with

Open the menu with »menu«.

Select the menu item »SOURCE SETUP« with

v« or »Λ« and press »oK« to confirm.

– The »SOURCE SETUP« menu appears.

Select »Device Standby« with »v« or »Λ«

20.09.2010

15:46

and press »oK« to confirm.

SOURCE SETUP

– The external device switches itself off.

Source

HDMI1

DIGILINK

GRUNDIG DVD

RC Passthrough

Device Selection

Remote Control

Device Standby

Exit

Back

Select the line »Remote Control« with »

or » «.

v«

5- Select the type of operation (»RC Pass-

through«, »Deck« or »Tuner« with » « or

» «.

notes:

»RC Passthrough« can be used for all devices.

»Deck« and »Tuner« can be selected in ac-

cordance with the external device which

has been connected.

Try out which type of remote control opera-

tion the external device reacts to the best.

Read about the scope of functions of the

DIGILINK-compatible device in the respec-

tive operating manual.

Press »menu« to end the setting.

-43

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

operAtion-usinG-externAl-DeviCes_{------------------------------}

high-definition--hD-ready

Connection-options

Which television socket(s) you connect your

Connect the corre-

external devices to depends on the sockets

the external device is equipped with and the

signals which are available.

sponding input sources

(e.g. HDTV receiver or

HD-DVD player) to the

»hDmi« sockets (for

digital HDTV sources).

Please note: With many external devices,

the resolution of the video signal must be

adjusted to the input sockets of the television

(see the operating manual of the external

device). You can find out which values you

need to set by referring to the guidelines in

the sections about the various connection

options.

This ensures that you can view digital HDTV

programmes, even if they are copy-protected

(HDCP High Bandwidth Digital Content Protec-

tion), without encountering problems.

Do not connect any other equipment while

the device is switched on. Also switch off the

other equipment before connecting it.

Do not plug in the power cord of the device

until you have connected the external equip-

ment and the antenna.

-44

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

operAtion-usinG-externAl-DeviCes_{------------------------------}

...-using-the-sCArt-socket--

(CvBs/rGB-signal)

Connecting-external-devices

...-with-digital-audio/video-signals

Suitable devices: Digital satellite receiver,

Suitable devices: Digital satellite receivers,

DVD player/recorder, set-top box, games con-

sole, video recorder, decoder.

Video signal: CVBS/RGB.

Audio signal: stereo, analogue.

»AV1« preset.

Playstation, BluRay player, DVD player/

recorder, set-top box, notebook, PCs.

Video signal: Digital video; resolution: stand-

ard 576p; HDTV 720p, 1080i, 1080p.

Audio signal: digital audio (stereo, multi-chan-

Connect the »Av1/s-vhs« socket on the

television and the corresponding socket on

the external device using a SCART cable

(video and audio signal).

nel compression, uncompressed).

Presets »HDMI 1«, »HDMI 2« or »HDMI3«.

Connect

the »hDmi1«, »hDmi2«,

» hDmi3« socket on the television and the

corresponding HDMI socket on the external

device using a standard HDMI cable (digital

video and audio signal).

Activating-a-decoder

If a decoder is connected to the »Av1/s-vhs«

socket, this must be activated to provide an

unencrypted video/audio signal.

...-with-analogue-video-signal-

(progressive)

Open the menu with »menu«.

Select »SETTINGS« with »v« or »Λ« and

press »oK« to confirm.

– The »SETTINGS« menu appears.

Suitable devices: DVD recorders/players,

games consoles.

Video signal: YUV; resolution: standard 576p;

HDTV 720p, 1080i, 1080p.

Audio signal: stereo, analogue.

»Component« preset.

Select the »Decoder« with »

v« or »Λ«.

Activate the function with » « or » «

(»On«).

Press »menu« to end the setting.

Connect the »Component- Y/Av2- pb-

pr« sockets on the television to the corre-

sponding sockets of the external device with

RCA cables (video signal).

...-with-s-video-signal

Suitable devices: DVD player/recorder, video

recorder, camera recorder, notebook, PC.

Video signal: Y/C.

Audio signal: stereo, analogue.

»S-VHS« preset.

Connect the »Component-l-r« sockets

on the television to the corresponding sock-

ets of the external device with RCA cables

(audio signal).

1- Connect the » Av1/s-vhs« socket on the

television and the corresponding socket on

the external device using an EURO/AV ca-

ble (video and audio signal).

-45

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

operAtion-usinG-externAl-DeviCes_{------------------------------}

...-with-an-analogue-tv-signal

using-a-DvD-player,-

DvD--recorder,-video-recorder--

or-set-top-box

Suitable devices: Digital satellite receiver,

DVD player/recorder, set-top box, camera

recorder.

Video signal: CVBS.

Audio signal: stereo, analogue.

»AV2« preset.

Switch on the external device and select the

function you wish to use.

Press

«, use »v«, »Λ«, » « or » « to

select the preset for the input signal (»AV1«,

»AV2«, »S-VHS«, »HDMI1«, »HDMI2«,

»HDMI3« or »Component«) and press

»oK« to confirm.

Connect the »Y/Av2« socket on the

television to the corresponding socket of the

external device with an RCA cable (video

signal).

Connect the »l--r« sockets on the television

to the corresponding sockets of the external

device with RCA cables (audio signal).

headphones

Connecting-the-headphones

Plug the headphone jack (3.5 mm ø jack

plug) into the headphone socket on the left

side of the television.

Changing-the-headphone-volume

Open the menu with »menu«.

Select the menu item »SOUND SETTINGS«

with »v« or »Λ« and press »oK« to confirm.

– The »SOUND SETTINGS« menu appears.

Select the menu item »Audio Output Setup«

with »

v« or »Λ« and press »oK« to confirm.

– The »Audio Output Setup« menu appears.

Select the line »Headphone« with » « or

»Λ«.

Set the preferred volume with » « and » «.

Press »menu« to end the setting.

note:

Prolonged listening with headphones at loud

volumes can damage your hearing.

-46

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

operAtion-usinG-externAl-DeviCes_{------------------------------}

playing-the-audio-signal-via-the--

hiFi-system

1- Connect the »U« sockets on the television to

the corresponding socket of the AV receiver

with an cable (digital audio signal).

hi-fi-system/Av-receiver

Connecting-the-hi-fi-system/-

Av-receiver

1- Connect the »optic- out« socket on the

television to the corresponding socket of the

device with an optical digital cable (digital

audio signal).

note:

If this function is not activated, the audio sig-

nal is transmitted to the HiFi system/AV re-

ceiver (connected to »U« 3.5 mm ø jack

plug) into the headphone socket on the left

side of the television.

setting-the-audio-format

You can select whether the audio signal output

via the »optic-out« socket should be in the

PCM or AC2 format.

Open the menu with »menu«.

Select the menu item »SOUND SETTINGS«

with »v« or »Λ« and press »oK« to confirm.

Select the menu item »SOUND SETTINGS«

– The »SOUND SETTINGS« menu appears.

with »v« or »Λ« and press »oK« to confirm.

– The »SOUND SETTINGS« menu appears.

Select »Audio Output Setup« with » « or

Λ« and press »oK« to confirm.

Select »Audio Output Setup« with » « or

– The menu appears.

Λ« and press »oK« to confirm.

– The menu appears.

Select the line »Audio Out« with »v« or »Λ«

and press » « or » « to activate the audio

Select the »Optic Out« with »v« or »Λ«.

output (»Line Out«).

Select the line » Audio Out Status« with »

or » « and select the option »Fixed« or »Ad-

justable« with » « or » «.

Select the preferred audio format (»PCM« or

»Auto«) with » « or » «.

v«

note:

If you wish to output the audio only via a

multi-channel amplifier/AV receiver, set the

option »TV Speaker« to »Off« in the menu.

notes:

If you select »Adjustable«, the volume can

be changed in the menu option » Audio Out

Volume«.

Press »menu« to end the setting.

If the audio should only be output via the

HiFi system/AV receiver, select the option

»Off« in the line »TV Speaker with » « or

» «.

Press »menu« to end the setting.

“Dolby” and the double-D logo are trademarks of

Dolby Laboratories.

Manufactured under licence from Dolby Laboratories.

-47

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

operAtion-As-A-pC-monitor_{-----------------------------------------------------------}

Connecting-a-pC

20.09.2010

15:46

Connect the »pC-in« socket on the television

to the corresponding socket on the PC using

a VGA cable (video signal).

SOURCE SETUP

Connect the »Audio« socket on the televi-

sion to the corresponding socket on the PC

using a suitable cable (audio signal).

Source

Auto Ajust

Extended settings

note:

Auto Ajust Mode

50H - 50V

Adjust your PC to the monitor (for example,

picture resolution 1280 x 768, picture fre-

quency 60 Hz).

Position

Size

Phase

selecting-presets-for-the-pC

Press »

« and use »v«, »Λ«, » « or » «

Exit

Back

to select the preset »PC« and press »oK« to

confirm.

Options:

settings-for-pC-mode

–

»Auto Ajust« for automatic PC configura-

tion.

Open the menu with »menu«.

– »Auto Ajust Mode«, select the option

»On« if the configuration should be imple-

mented automatically in PC mode.

– »Position« to configure the horizontal and

vertical picture position.

– »Size« to set the cycle frequency.

– »Phase« to eliminate flicker, unfocused

pictures or horizontal interference.

Select the »SOURCE SETUP« menu item with

v« or »Λ« and press »oK« to confirm.

– The »SOURCE SETUP« menu appears.

3- Select the function or setting with » « or

« or » «, » « to

Λ«, and then use »v«, »Λ

implement it.

Press »menu« to end the setting.

-48

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

operAtion-with-A-Common-interFACe_{-------------------}

what-is-a-Common-interface?

Access-control-for-Ci-module-and-

smart-card

Common Interface (CI) is an interface for

DVB receivers.

Encrypted channels can only be viewed

Open the menu with »menu«.

Select the line »SOURCE SETUP« with »

or »Λ« and press »oK« to confirm.

v«

with a CA module suitable for the encryp-

tion system and in conjunction with the

corresponding smart card.

The television set is equipped with a Com-

mon Interface slot into which CI modules

from various providers can be inserted.

You can insert the provider’s smart card into

the CA module in order to enable the en-

crypted channels you wish to view.

– The »SOURCE SETUP« menu appears.

Select the line »CA-Module« with » « or

« and press »oK« to confirm.

notes:

This menu provides operating instructions

and – after you enter your PIN code – ac-

cess to the PAY-TV provider's channels.

inserting-the-CA-module

note:

The remaining settings are described in the

operating manuals for your CI module and

smart card.

Switch the device off before you insert a CA

module into the »Ci« slot.

The CA modul is not supported in certain

countries and regions; please consult your

authorised dealer.

Insert the corresponding smart card into the

CI module.

Insert the CI module with the smart card into

the »Ci« slot on the television.

Press »menu« to end the setting.

note:

In the »CA Module« sub-menu you can see

which CA module has been inserted in the

CI slot.

If you are inserting a CA module into the

CI slot of the television for the first time, you

will need to wait a moment until the CA mod-

ule is detected.

-49

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

speCiAl-settinGs_{-----------------------------------------------------------------------------------------------------------}

note:

searching-for-television-chan-

You can accelerate the search. To do this,

you need information about the frequency

and network ID. You are usually able to get

this data from your cable operator or find it

in forums on the Internet. For example, the

frequency 402MHz and network ID 61441

can be entered for Germany.

nels-from-the-cable-provider-

automatically

Open the menu with »menu«.

Select the line »SOURCE SETUP« with »

or »Λ« and press »oK« to confirm.

– The »SOURCE SETUP« menu appears.

Select the line »Source« with

or » « and press »oK« to confirm.

Select the option »Cable« with » «, » «,

Start the scan with » «-(red).

– All channel and favourites lists will be

deleted and compiled anew.



»v

« or »

Select the line »Automatic Channel Search«

with » « or » « and press »oK« to confirm.

– The menu appears.

Λ« and press »oK« to confirm.

note:

After starting the scan, a security query will

appear. Press » « (green) to confirm the



option »Yes«.

– The »Results« menu appears, and the scan

for TV channels begins. Depending on the

number of television channels received,

this can easily take a few minutes.

20.09.2010

15:46

SOURCE SETUP

AUTOMATIC CHANNEL SEARCH

– The scan is complete as soon as the »PRO-

GRAM TABLE« appears.

Connection Type

Cabel

U.K.

Country

note:

ATV & DTV

Quick

Scan Type

You can abort the search by pressing

»menu«.

Cable Scan Type

Frequency (MHz)

Network ID

Auto

Press »menu« to end the setting.

Auto

Exit

Back

Start Search

Select the line »Scan Typ« with »

« or »

and set the option »DTV« with » « or » «.

Select the line »Cable Scan Type« with »

or »

with » « or » «.

v«

Λ« and set the option »Quick« or »Full«

– The search function »Quick« sets the channels

according to the information provided by your

cable provide in the transmission signal.

– If the option »Full« is selected, the entire fre-

quency range will be scanned. The search

can take a long time with this option. This op-

tion is recommended if your cable provider

does not support the search type »Quick«

-50

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

speCiAl-settinGs_{-----------------------------------------------------------------------------------------------------------}

searching-for-television-channels- searching-for-digital-terrestrial-

from-the-cable-provider-manu-

ally

tv-channels-automatically

Open the menu with »menu«.

Select the line »SOURCE SETUP« with »

or »Λ« and press »oK« to confirm.

Select the line »SOURCE SETUP« with »

– The »SOURCE SETUP« menu appears.

Select the line »Source« with

or » « and press »oK« to confirm.

Select the option »Air« with » «, » «, »

or »Λ« and press »oK« to confirm.

– The »SOURCE SETUP« menu appears.

Select the line »Source« with »v« or »

v« or

and press »oK« to confirm.

Λ« and press »oK« to confirm.

Select the option »Cable« with » «, » «,

»v« or »Λ« and press »oK« to confirm.

Caution:

Select » Digital Manual Tuning« with »

« or

The antenna power supply (line »Active

Antenna Power«) may only be switched on

if the antenna is an active indoor antenna

with a signal amplifier and it is not already

supplied with a voltage via a mains plug

(or similar supply). Otherwise you may

cause a short circuit and irreparably dam-

age your antenna.

« and press »oK« to confirm.

– The menu appears.

Enter the four-digit frequency with »1-...-0«

and press »oK« to confirm.

–

The search starts after confirming, the

channels found are displayed in the »Re-

sults« menu.

Select the »Active Antenna Power« with »

or » «. Switch on the antenna power supply

for the antenna with » « or » « (»On«).

v«

Press »menu« to finish the setting.

Select the line »Automatic Channel Search«

with »v« or »Λ« and press »oK« to confirm.

– The menu appears.

20.09.2010

15:46

SOURCE SETUP

AUTOMATIC CHANNEL SEARCH

Connection Type

Air

U.K.

Country

ATV & DTV

Scan Type

Exit

Back

Start Search

-51

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

speCiAl-settinGs_{-----------------------------------------------------------------------------------------------------------}

Select the line »Scan Typ« with »

v« or »Λ«

searching-for-digital-terrestrial-

tv-channels-manually

and set the option »DTV« with » « or » «.

Start the scan with » «-(red).



Open the menu with »menu«.

– All channel and favourites lists will be

deleted and compiled anew.

Select the line »SOURCE SETUP« with »

or »Λ« and press »oK« to confirm.

note:

– The »SOURCE SETUP« menu appears.

After starting the scan, a security query will

Select the line »Source« with »v« or »

appear. Press » « (green) to confirm the



and press »oK« to confirm.

option »Yes«.

Select the option »Air« with » «, » «, »v« or

– The »Reults« menu appears, and the scan

for TV channels begins. Depending on the

number of television channels received,

this can easily take a few minutes.

– The scan is complete as soon as the

»PROGRAM TABLE« appears.

»Λ

« and press »oK« to confirm.

Caution:

The antenna power supply (line »Active

Antenna Power«) may only be switched on

if the antenna is an active indoor antenna

with a signal amplifier and it is not already

supplied with a voltage via a mains plug

(or similar supply). Otherwise you may

cause a short circuit and irreparably dam-

age your antenna.

note:

You can abort the search by pressing

»menu«.

Press »menu« to end the setting.

Select the »Active Antenna Power«« with »

or » «. Switch on the antenna power supply

for the antenna with » « or » « (»On«).

v«

Automatic-service-update-

If this function is activated, possible changes of

network operators are updated automatically.

Select » Digital Manual Tuning« with »

« and press »oK« to confirm.

– The menu appears.

v« or

The unit must be located in stand-by mode.

»Λ

Open the menu with »menu«.

Select the line »SOURCE SETUP

or » « and press »oK« to confirm.

Select the line »Automatic Service Update«

with » « or » «.

Enter the channel number directly with

1-...-0« and press »oK« to confirm.

with »v«

–After the search is complete, the channels

found are displayed in the »Results« menu.

Press »menu« to finish the setting.

Select the automatic update with » « or » «

(»On«).

Press »menu« to end setting.

-52

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

speCiAl-settinGs_{-----------------------------------------------------------------------------------------------------------}

Select the line »Scan Typ« with »

v« or »Λ«

tuning-analogue-television-

-channels

This setting is only necessary if you cannot re-

ceive any digital channels and you have not car-

ried out an analogue search during initial setup.

The television channels can be set directly or

using the scan.

and set the option »ATV« with » « or » «.

Start the scan with » «-(red).



note:

After starting the scan, a security query will

appear. Press » « (green) to confirm the



option »Yes«.

– All channel and favourites lists for the ana-

logue channels will be deleted and com-

piled anew.

setting-all-analogue-television-

channels

– The »Results« menu appears, and the scan

for TV channels begins. Depending on the

number of television channels received,

this can easily take a few minutes.

– The search is complete as soon as the »PRO-

GRAM TABLE« appears.

Analogue channels are displayed in the channel

list after the digital channels.

note:

Plug the rooftop antenna cable (for analogue

television channels) into the »Ant-in«

socket on the television.

note:

Open the menu with »menu«.

You can abort the search by pressing

»menu«.

Select the line »SOURCE SETUP« with »

or »Λ« and press »oK« to confirm.

Press »menu« to end the setting.

– The »SOURCE SETUP« menu appears.

Select the line »Source« with »v« or »

and press »oK« to confirm.

Select the option »Air« or »Cable« with » «,

» «, »

v« or »Λ« and press »oK« to con-

firm.

Select the line »Automatic Channel Search«

with »

v« or »

Λ« and press »oK« to confirm.

20.09.2010

15:46

SOURECE SETUP

Source

Air

Automativ Channel Search

Digital Manual Tuning

Analogue Manual Tuning

Program Table

Signal Information

Automatic Service Update

CA - Modul

Not inserted

Off

Active Antenna Power

Exit

Back

-53

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

speCiAl-settinGs_{-----------------------------------------------------------------------------------------------------------}

tuning-the-television-channels-by-

entering-the-channel-numbers

Changing-stored-analogue-

-channels

If channels were stored with the automatic chan-

nel search while tuning the television channels,

you can delete them. You can also store chan-

nels in a different preset, change or enter the

name of a channel as well as skip channels.

Open the menu with »menu«.

Select the line »SOURCE SETUP« with »

v«

or »Λ« and press »oK« to confirm.

– The »SOURCE SETUP« menu appears.

Select the line » Analogue Manual Tuning«

with »v« or »Λ« and press »oK« to confirm.

selecting-a-channel-list

– The menu appears.

Open the menu with »menu«.

Select the line »SOURCE SETUP« with »

v«

INSTALLATION

ANALOGUE MANUAL TUNING

or »Λ« and press »oK« to confirm.

– The »SOURCE SETUP« menu appears.

Program No

TSystem

Band

Select the line »Program Table« with » « or

Λ« and press »oK« to confirm.

– The »PROGRAME TABLE« menu appears.

note:

Channel

Additional operations are explained in the

following sections.

Fine Tuning

48.25 MHz

Deleting-channels

In the »PROGRAME TABLE« menu, select the

television channel to be deleted with «,

«, » « or » « and press » «-(red) to con-

Auto Previous

Auto Next

Store

»v

firm.



Select the line »Program No« by pressing »

or » « and use » « or » « to save the preset.

Select »Band« by pressing »

use »» « or » « to choose between »S«

v«

Press » « (yellow) to confirm the deletion



« or »

(special channel) or »C« (normal channel).

Select the line »Channel« with » « or » « and

Λ« and

process.

note:

« (blue) allows all television channels



enter the channel number with » « or » « step

by step, or use »1…0« to enter it directly.

to be deleted.

Press » « (green) to confirm the deletion



notes:

process.

The current system is displayed in the

»System« line. If the colour or sound is

not functioning properly, select the line

»System« with »v« or »Λ«. Use » « or » «

to select the preferred setting.

If fine tuning is necessary, select the line

»Fine Tuning« with » « or » « and use » «

or » « to make the setting.

Press » « (blue) to save the setting.



note:

If you wish to remedy other television

channels, repeat steps 4 to 8.

8- Press »menu« to end the setting.

-54

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

speCiAl-settinGs_{-----------------------------------------------------------------------------------------------------------}

entering-channel-names-(8-digit-

maximum)

Creating-lists-of-favourites

You can select your favourite channels and

save them in up to four favourites lists (Fav 1 to

Fav 4).

In the »PROGRAME TABLE« menu, select the

television channel with » «, » «, » « or

» « and press » «-(red) to confirm.



In the »PROGRAME TABLE« menu, switch

over to the list view with » « (yellow).



Open the input keyboard with » « (green).



Select the preferred channel with »

or »Λ«.

v«

note:

If necessary, delete the current channel

name. To do this, select the »

« button

Use » « or » « to ”push“ the channel into

with » « or » « and delete repeatedly using

one of the favourites lists 1 to 4 and press

»oK« to confirm.

»oK«

Select the required letters or numbers with

«, » «, » « or » « and confirm with

»oK«

– The position in the favourites list is marked

with »✔«.

– You can enter the same channel in more

than one favourite list.

– Eachfavouritelistcanstoreupto255 chan-

nels.

Repeat the entry for further letters/numbers.

note:

Use the »ABC« button to switch to upper

note:

case letters and use the »?@123« button to

switch to symbols and numbers.

Channels can also be deleted from favour-

ites lists. Select the channel to be deleted

with »

v«, »Λ«, » « or » « and delete it with

Save the channel name by using »v«, »Λ«,

»oK«

» « or » « to select »Submit« and confirm

with »oK«

exiting-the-settings

Press »menu« to end the setting.

note:

If you wish to enter other channel names,

repeat steps 1 to 4.

skipping-television-channels

You can highlight television channels to be

skipped when you select with »Λ« or »v«.

Selection is still possible using the number

buttons.

In the »PROGRAMETABLE« menu, switch over

to the list view with » « (yellow).



Select the preferred channel with »

v«

or »Λ«.

Select the column »Skip« with » « or » «

and use »oK« to mark the channel.

– The channel is marked using »✔«.

note:

Channels can also be reactivated. Select the

channel with » « or » «, then select the

column »Skip« and reactivate the channel

with »oK«

-55

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

inFormAtion_{----------------------------------------------------------------------------------------------------------------------}

Displaying-signal-information

(for digital channels only)

service-information-for-retailers

Only operate the television

with the power supply/power

cord provided.

The product complies with the

Open the menu with »menu«.

Select the line »SOURCE SETUP« with »

or »Λ« and press »oK« to confirm.

v«

following EU directives:

2006/95/EC directive on electrical equipment

for use within certain voltage limits.

2004/108/EC directive on electromagnetic

compatibility.

2009/125/EC directive on ecodesign require-

ments for energy-related products.

Power consumption values and classes are speci-

fied according to the regulations 2009/642 and

2010/1062 and the standards EN62087 and

EN62301 as per European Union framework di-

rectives 2009/125/EC and 2010/30/EU

Select the line »Signal Information« with

« or » « and press »oK« to confirm.

– Information on the channel, network,

modulation, symbol rate, quality and

signal strength is displayed.

»v

notes:

The signal information changes in accord-

ance with the current input source.

The signal properties are displayed in the

lower section of the menu. The further the

bars for »Quality« and »Signal Strenght«

extend to the right, the better the reception

signal.

environmental-note

This product has been made

from high-quality parts and

The signal level not only depends on your

receiver system, but also on the channel

which is currently active. Remember this

when aligning your antenna based upon

the signal level display.

materials which can be re-used

and recycled.

Therefore, do not dispose of the

product along with normal household waste at

the end of its service life. Take it to a collection

point for the recycling of electrical and electronic

equipment. Dispose of the used device at a collec-

tion point for electrical and electronic equipment.

The symbol on the product, in the operating man-

ual or on the packaging indicates that recycling

is possible.

Press »menu« to close the menu.

Information on collection points is available from

your local authorities.

Help protect the environment by recycling used

products.

-56

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

inFormAtion_{----------------------------------------------------------------------------------------------------------------------}

Analogue-reception-ranges:

C02 ... C80, special channels S01 ... S41

GrunDiG-32-vlC-6121-C

technical-data

preset-channels:-

operating-voltage:-

TV/Radio

1000 (Cable – DVB-C) or

100 (Analogue)

1000 (Terrestrial – DVB-T) or

100 (Analogue)

8 AV, 1 USB

220–240 V, , 50–60 Hz

power-consumption:

On mode 83 W

Standby < 0,50 W

screen-(dm²):

28 dm²

screen-size:

80 cm/32 inch

energy-efficiency-class:

maximum-power-consumption

Operational 145 W

maximum-resolution:

WUXGA, 1920 x 1080

Annual-power-consumption

121 kWh

weight:

approx. 12 kg

Audio-output:-

2 x 20 W music power output

2 x 10 W Sine wave power

Dimensions:

W H D 79,5 cm 54,5 cm 8,1 cm

rohs-limits: Pb (Lead)/Hg (Mercury)

Pb meets ROHS directive / 56 mg

peak-luminance-ratio:

% 65

Digital-reception-ranges

Cable:

Overall band: 110 MHz – 862 MHz

Modulation:

16QAM, 32QAM, 64QAM,

128QAM and 256QAM

Symbol rate: 4.0 Msym/s to 7.0 Msym/s

terrestrial:

VHF/UHF band, Bandwidth 7 MHz

and 8 MHz

COFDM modi: 2k and 8k

Constellation: 16QAM, 64QAM, QPSK

terrestrial-(DvB-t2):

VHF/UHF band, Bandwidth 7 MHz

and 8 MHz

FFT Size:

Modulation:

1k, 2k, 4k, 8k, 16k, 32k

16QAM, 64QAM,

256QAM, QPSK

Guard Interval: 1/4, 19/256, 1/8, 19/128,

1/16, 1/32, 1/128

As this feature is optional, it is not available in

all products.

Technical changes and errors reserved.

-57

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

inFormAtion_{----------------------------------------------------------------------------------------------------------------------}

troubleshooting

If the information provided below does not help, please consult an authorised GRUNDIG dealer.

Please bear in mind that malfunctions can also be caused by external devices such as video recorders

or satellite receivers.

problem

possible-cause

remedy

Screen lit (snow), but no

station visible

Antenna cable

Is the antenna cable connected?

No TV channel tuned

Start a channel scan

Insuﬃcient contrast in picture

The picture settings are not correct

Adjust the brightness, contrast or

colour setting

Problem at station

Try another channel

Picture and/or sound distorted Interference from other devices

Place the device in a diﬀerent position

Ghosting, reﬂection

No colour

Channel setting

Antenna

Automatic or manual tuning/ﬁne tuning

Have antenna cable or system checked

Turn up the colour

Colour intensity too low

Adjust TV standard (if setting option

is available)

Select the correct colour standard

Problem at station

Try a diﬀerent channel

Picture but no sound

Volume is set to a minimum

Turn up or switch on the volume

Teletext impaired or absent

Problem at station

Try a diﬀerent channel

Television channel (no teletext)

or antenna system

Try with a diﬀerent TV channel,

carry out ﬁne tuning

Station signal too weak

Check antenna

The remote control does

not work

Obstacle between remote control

and device.

Point remote control at television

Battery problem

Check batteries and replace if

necessary

Operating mode undeﬁned

Switch oﬀ the television at the mains

switch for two minutes

Picture too dark in PC mode

Incorrect setting for picture resolution Change settings on the PC

and picture frequency on the PC

(e.g. 1280 x 768 resolution,

refresh rate 60 Hz)

note:

This is a Class A product. During operation the device could cause radio interference. In this case

the user may have to remedy this. Please contact your specialist dealer.

-58

ENGLISH

Download from Www.Somanuals.com. All Manuals Search And Download.

GSI Outdoors Ventilation Hood PNEG 524 User Manual
Haier Refrigerator PBFS21 User Manual
Haier Washer Dryer HWDC1000TXVE ME U User Manual
Haier Washer XPM20 A User Manual
Harbor Freight Tools Nail Gun 98917 User Manual
Harbor Freight Tools Paint Sprayer 97855 User Manual
Hotpoint Cooktop EG74 User Manual
Hotpoint Electric Pressure Cooker GW32 User Manual
Hotpoint Washer WM61 User Manual
Husqvarna Chainsaw 3120XP User Manual